This patch adds driver changes for capturing the link change count in
ethtool statistics display.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.
For example -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of build_skb() throughout in driver's receieve
data path [HW gro flow and non HW gro flow]. With this, driver can
build skb directly from the page segments which are already mapped
to the hardware instead of allocating new SKB via netdev_alloc_skb()
and memcpy the data which is quite costly.
This really improves performance (keeping same or slight gain in rx
throughput) in terms of CPU utilization which is significantly reduced
[almost half] in non HW gro flow where for every incoming MTU sized
packet driver had to allocate skb, memcpy headers etc. Additionally
in that flow, it also gets rid of bunch of additional overheads
[eth_get_headlen() etc.] to split headers and data in the skb.
Tested with:
system: 2 sockets, 4 cores per socket, hyperthreading, 2x4x2=16 cores
iperf [server]: iperf -s
iperf [client]: iperf -c <server_ip> -t 500 -i 10 -P 32
HW GRO off – w/o build_skb(), throughput: 36.8 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.59 0.00 32.93 0.00 0.00 43.07 0.00 0.00 23.42
HW GRO off - with build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.70 0.00 31.70 0.00 0.00 25.68 0.00 0.00 41.92
HW GRO on - w/o build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.86 0.00 24.14 0.00 0.00 6.59 0.00 0.00 68.41
HW GRO on - with build_skb(), throughput: 37.5 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.87 0.00 23.75 0.00 0.00 6.19 0.00 0.00 69.19
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds ethtool callback implementation for flash update.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise NETIF_F_GRO_HW and set edev->gro_disable according to the
feature flag. Add qede_fix_features() to drop NETIF_F_GRO_HW if
XDP is running or MTU does not support GRO_HW or GRO is not set.
qede_change_mtu() also checks and disables GRO_HW if MTU is not
supported.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds ethtool callback implementations for querying/configuring
the Energy Efficient Ethernet (EEE) parameters.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for adding and deleting rx flow
classification rules. Using this user can classify RX flow
constituting of TCP/UDP 4-tuples [src_ip/dst_ip and src_port/dst_port]
to be steered on a given RX queue
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool getter APIs to query
RX flow classification rules.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Solves the following warning in qede -
- Several cases of missing cpu_to_le16() conversions
- Adds 'static' to one function declaration
- Removes dcbnl operation that's currently getting populated twice
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some variants of adapters support the 1G speed capability. Need to
allow the configuration of 1G speed if adapter supports it.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver always allocates the maximal number of tx-buffers irrespective of
actual Tx ring config.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fail the configuration of advertised speed-autoneg value if the config
update is not supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value for status block id could be more than 256 in 100G mode, need to
update its data type from u8 to u16.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.
It also adds 2 new PCI device-IDs to qede:
- 0x8070 for QL41xxx PFs
- 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently utilizes the same loop variable in two
nested loops.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver support for,
- Registering the ptp clock functionality with the OS.
- Timestamping the Rx/Tx PTP packets.
- Ethtool callbacks related to PTP.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for forwarding via XDP. Once the eBPF is attached,
driver would allocate & configure a designated transmission queue
meant solely for forwarding packets. Said queue would share the
receive-queue's interrupt line, and would have it's own Tx statistics.
Infrastructure changes required for this [spread-out through the code]:
- Determine the DMA direction of the receive buffers based on the presence
of the eBPF program.
- Turn the sw Tx ring into a union, as regular/XDP queues have different
needs for releasing resources after completion [regular requires the SKB,
XDP requires the transmitted page].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ndo_xdp callback. This patch would support XDP_PASS,
XDP_DROP and XDP_ABORTED commands.
This also adds a per Rx queue statistic which counts number of packets
which didn't reach the stack [due to XDP].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the cacheline usage of both queues by reordering -
This reduces the cachelines required for egress datapath processing
from 3 to 2 and those required by ingress datapath processing by 2.
It also changes a couple of datapath related functions that currently
require either the fastpath or the qede_dev, changing them to be based
on the tx/rx queue instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As qede utilizes an internal-reload sequence as result of various
configuration changes, the netif state wouldn't always accurately describe
the status of the configuration.
To compensate, we're storing an internal state of the device, which should
only be accessed under the qede_lock.
This patch fixes and improves several state/lock interactions:
- The internal state should only be checked while locked.
- While holding lock, it's preferable to check state rather than
the netdevice's state.
- The reload sequence is not 'atomic' - unload and subsequent load
are not in the same critical section.
This also add the 'locked' variant for the reload, which would later be
used by XDP - useful in the case where the correct sequence is 'lock,
check state and re-configure if good', instead of allowing the reload
itself to make the decision regarding the configurability of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor logic for gathering statistics into a per-queue function.
This improves readability of the driver statistics' flows.
In addition, this would be required by the XDP forwarding queues
[as we'll need the Txq statistics gathering methods for those as well].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently doesn't support multi-CoS, but it contains logic
where multiple transmission queues could be theoretically manipulated.
No point in maintaining the infrastructure at the moment.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the qed_lm_maps is closely tied with the QED_LM_* defines,
when iterating over the array use actual size instead of the qed
define to prevent future possible issues.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is interested in various tidbits about
the driver - including the driver state & several configuration
related fields [MTU, primtary MAC, etc.].
This adds the necessray logic to update MFW with such configurations,
some of which are passed directly via qed while for others APIs
are provide so that qede would be able to later configure if needed.
This also introduces a new default configuration for MTU which would
replace the default inherited by being an ethernet device.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is configured to use Tx/Rx-only queues,
the length of the statistics would be shortened to accomodate only the
statistics required per-each queue, and the values would be provided
accordingly.
However, the strings provided would still contain both Tx and Rx strings
for each one of the queues [regardless of its configuration], which might
lead to out-of-bound access when filling the buffers as well as incorrect
statistics presented.
Fixes: 9a4d7e86ac ("qede: Add support for Tx/Rx-only queues.")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses incorrect APIs to unmap DMA memory which were
mapped using dma_map_single(). This patch fixes it to use
appropriate APIs for un-mapping DMA memory.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx indirection table entries are in the range [0, (rss_count - 1)]. If
user reduces the rss count, the table entries may not be in the ccorrect
range. Need to reconfigure the table with new rss_count as a basis.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the execution of loopback test, driver may receive the packets which
are not originated by this test, loopback implementation need to skip those
packets.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS configuration is not supported for 100G adapters.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes in kernel ethtool implementation requires the driver
callback for get_channels() has to populate the values for max tx/rx
coalesce fields.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h
qlcnic: min_mtu 68, max_mtu 9600
CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of the per-queue statistics introduced a harmless warning
on all 32-bit architectures:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function 'qede_get_ethtool_stats':
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
This changes the cast to 'void *' to shut up the warning, which
avoids the assumptions on the size of the pointer type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68db9ec2df ("qede: Add support for per-queue stats.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make semantic-only adjustments to qed* drivers, such as:
- Changes in code indentation.
- Usage of BIT() macro.
- re-naming of variables.
- Re-ordering of variable declerations.
- Removal of (== 0) and (!= 0) in conditions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.
Please consider applying this to 'net-next' branch.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling IP fragmented packets with csum in their
transport header, the csum isn't changed as part of the
fragmentation. As a result, the packet containing the
transport headers would have the correct csum of the original
packet, but one that mismatches the actual packet that
passes on the wire. As a result, on receive path HW would
give an indication that the packet has incorrect csum,
which would cause qede to discard the incoming packet.
Since HW also delivers a notification of IP fragments,
change driver behavior to pass such incoming packets
to stack and let it make the decision whether it needs
to be dropped.
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
