We add support for the PCIFB2 card from EAE.
Beside other cards, this card has the backplane mode enabled by default.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We read the backplane mode of each subcard from bits 2 and 3 of the misc
register.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the sysfs interface the read back the backplane
status of the interface.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to track the status of our queued packages. This way the driving
process knows if failed packages need to be retransmitted. For this
purpose we queue the transferred/failed packages back into the err_skb
message queue added with some status information.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the pdev data to the pci devices netdev structure. This way
the interface get consistent device names in the userspace (udev).
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_id was miscalculated. Only the two bits 4-5 are relevant for the
MA1 card. PCIARC1 and PCIFB2 use the four bits 4-7 for id selection.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change some general performance settings and to provide
some performance settings based on the device that is probed.
This includes:
- Setting the maximum read/write outstanding request limit
- Reducing the AXI interface burst length size
- Selectively setting the Tx and Rx descriptor pre-fetch threshold
- Selectively setting additional cache coherency controls
Tested and verified on all versions of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver hardcodes the PBLx8 setting. Remove the need for
specifying the PBLx8 setting and automatically calculate based on the
specified PBL value. Since the PBLx8 setting applies to both Tx and Rx
use the same PBL value for both of them.
Also, the driver currently uses a bit field to set the AXI master burst
len setting. Change to the full bit field range and set the burst length
based on the specified value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In prep for setting fine grained read and write DMA cache coherency
controls, allow specific values to be used to set the cache coherency
registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IRQ affinity, set the affinity hints for the IRQs to be (initially) on
the processors corresponding to the NUMA node of the device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to perform memory allocations on the node of the device. The
original allocation or the ring structure and Tx/Rx queues allocated all
of the memory at once and then carved it up for each channel and queue.
To best ensure that we get as much memory from the NUMA node as we can,
break the channel and ring allocations into individual allocations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the device interrupts should function as level interrupts. For
some hardware configurations this requires setting some control bits
so that if the interrupt status has not been cleared the interrupt
should be reissued.
Additionally, when using MSI or MSI-X interrupts, run the interrupt
service routine as a tasklet so that the re-issuance of the interrupt
is handled properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I2C communication fails, it tends to always fail. Rather than
continuously issue an error message (once per second in most cases),
change the message to be issued just once.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has some missing functionality when operating in the mode that
supports 2.5GbE. Fix the driver to fully recognize and support this speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function that performs a software reset of the hardware
provides a return code. During driver probe check this return code and
exit with an error if the software reset fails.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just to be on the safe side, should the update of the timestamp registers
not complete, issue a warning rather than looping forever waiting for the
update to complete.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spurious Tx timestamp interrupts can cause an oops in the Tx timestamp
processing function if a Tx timestamp skb is NULL. Add a check to insure
a Tx timestamp skb is present before attempting to use it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PTP initialization, the Timestamp Control register should be
cleared and not the Tx Configuration register. While this typo causes
the wrong register to be cleared, the default value of each register and
and the fact that the Tx Configuration register is programmed afterwards
doesn't result in a bug, hence only fixing in net-next.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using SFPs, the supported and advertised settings should be initially
based on the SFP that has been detected. The code currently indicates the
overall support of the device as opposed to what the SFP is capable of.
Update the code to change the supported link modes, auto-negotiation, etc.
to be based on the installed SFP.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and centralize the mailbox command rate change interface by
having a single function perform the writes to the mailbox registers
to issue the request.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that ofdpa_neigh_del() can sometimes free
"found". It just makes sense to use it first before deleting it.
Fixes: ecf244f753 ("rocker: fix maybe-uninitialized warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f4 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case a VLAN device is enslaved to a bridge we shouldn't create a
router interface (RIF) for it when it's configured with an IP address.
This is already handled by the driver for other types of netdevs, such
as physical ports and LAG devices.
If this IP address is then removed and the interface is subsequently
unlinked from the bridge, a NULL pointer dereference can happen, as the
original 802.1d FID was replaced with an rFID which was then deleted.
To reproduce:
$ ip link set dev enp3s0np9 up
$ ip link add name enp3s0np9.111 link enp3s0np9 type vlan id 111
$ ip link set dev enp3s0np9.111 up
$ ip link add name br0 type bridge
$ ip link set dev br0 up
$ ip link set enp3s0np9.111 master br0
$ ip address add dev enp3s0np9.111 192.168.0.1/24
$ ip address del dev enp3s0np9.111 192.168.0.1/24
$ ip link set dev enp3s0np9.111 nomaster
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Tested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't hold any tx lock when trying to disable TX during reset, this
would lead a use after free since ndo_start_xmit() tries to access
the virtqueue which has already been freed. Fix this by using
netif_tx_disable() before freeing the vqs, this could make sure no tx
after vq freeing.
Reported-by: Jean-Philippe Menil <jpmenil@gmail.com>
Tested-by: Jean-Philippe Menil <jpmenil@gmail.com>
Fixes commit f600b69050 ("virtio_net: Add XDP support")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Robert McCabe <robert.mccabe@rockwellcollins.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 3.70a of the Designware has additional DMA registers so
add those to the ethtool DMA Register dump.
Offset 9 - Receive Interrupt Watchdog Timer Register
Offset 10 - AXI Bus Mode Register
Offset 11 - AHB or AXI Status Register
Offset 22 - HW Feature Register
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset adds support for Innova IPSec network interface card.
About Innova device:
--------------------
Innova is a network card with a ConnectX chip and an FPGA chip as a
bump-on-the-wire.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ I2C | | SBU | | +------+
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | Flash |
+-----+ +-------+
The FPGA synthesized logic is loaded from dedicated flash storage and has
access to its own dedicated DDR RAM.
The ConnectX chip firmware programs the FPGA by accessing its configuration
space over either the slow internal I2C link or the high-speed internal link.
The FPGA logic is divided into a "Shell" and a "Sandbox Unit" (SBU).
mlx5_core driver (with CONFIG_MLX5_FPGA) handles all shell functionality,
while other components may handle the various SBU functionalities.
The driver opens high-speed reliable communication channels with the shell and
the SBU over the internal link.
These channels may be used for high-bandwidth configuration or for SBU-specific
out-of-band data paths.
About Innova IPSec device:
--------------------------
Innova IPSec is a network card that allows offloading IPSec cryptography operations
from the host CPU to the NIC. It is an Innova card with an IPSec SBU.
The hardware keeps the database of IPSec Security Associations (SADB) in the FPGA's
DDR memory.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ Internal I2C | | IPSec | | +------+
| | SBU | |
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | |
| | | Flash |
|SADB | | |
+-----+ +-------+
Modes and ciphers:
Currently the following modes and ciphers are supported:
IPv4 and IPv6
ESP tunnel and transport modes
AES 128 and 256 bit encryption, with GCM authentication (RFC4106)
IV is generated using seqiv, in sync with Linux's geniv.
More modes and ciphers may be added later.
Notes:
In the future similar functionality will be included in a single-chip NIC.
About the driver:
-----------------
Patches 1-4 prepare some existing driver code for the new feature:
* Add support for reserved GIDs in the hardware GID table
* Allow multiple modules to enable hardware RoCE support independently
Patches 5-6 define structs and helper functions for QP work-queues.
Patches 7-11 add various FPGA-related features required for Innova.
IPSec.
Patch 12 adds abstraction layer for Mellanox IPSec-offload capable devices.
atches 13-16 add IPSec offload support to the mlx5 netdevice.
This driver services the new IPSec offload API introduced in commit
d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Configuration Path:
If Innova IPSec device is detected, the mlx5e netdevice gets the new
NETIF_F_HW_ESP feature and the xdo callbacks, indicating ESP offload
capabilities, and also the matching TX checksum and GSO features.
The driver configures offloaded Security Associations (SAs) by sending
an ADD_SA or DEL_SA message to the IPSec SBU, which updates the SADB in DDR.
These messages and their responses are sent over a high-speed channel.
Counters for ethtool are retrieved by the driver from the SBU.
Data path:
On receive path, the SBU decrypts ESP packets which match the offloaded SADB,
but keeps them encapsulated.
The SBU injects metadata (Mellanox owned ethertype) indicating that crypto-offload
has taken place, the SA with which it was done, and the authentication result.
The ConnectX chip performs RX checksum offload on the packet, and RSS using the
ESP SPI value. The driver detects the special ethertype, and attaches a struct
secpath to the RX SKB, including flags to indicate that crypto offload took place,
the authentication result, and which xfrm_state was used for decryption, in the
olen and ovec members. The RX SKB may have useful CHECKSUM_COMPLETE. A separate
patchset will add support for that in the xfrm stack.
On transmit path, the stack encapsulates the packet but does not encrypt it, and
indicates in the SKB's secpath that crypto offload is to be performed and the SA
to use to do so.
The driver avoids performing crypto-offload for ESP fragments, and packets with
IP options, as the SBU cannot currently do that. For eligible packets, the driver
prepends a special ethertype with metadata instructing the hardware to perform crypto offload.
The stack builds regular (non-GSO) SKBs so that they contain a placeholder for the ESP trailer.
The driver trims it off, because the SBU automatically appends the trailer for offloaded packets.
The ConnectX chip performs TX checksum offload on inner UDP or TCP packets,
and GSO for TCP packets (duplicating the prepended metadata).
The segmented packets then undergo encryption in the SBU before going on the wire.
Performance:
We measure single stream of TCP on Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz
Using AES-NI with ESP GSO we get constant 4.1 Gbps.
Using crypto offload we get constant 18 Gbps.
Note that these numbers require CHECKSUM_COMPLETE support in XFRM, which we submit separately.
- Ilan Tayari
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZUmf1AAoJEEg/ir3gV/o+ukIIALp/5+E1W0cC9xvY1X9dTETW
cKsHvDJ7G1CxUy18W8Mf9z+WOqC6hGCqS+yicOb+umfIqkTcLHDb2irlqprYLC+F
oYl1HqgHTaiAYByqL90qiyPcFbfsaNIqA9KOsED2qdZ1yxjoYBiJnSDZDAdO/0lN
Lt1czNswFc5ovnEUGn8bkjLZZH2pJoJWEI4g4hN9cq33BLLq8A795F/ZjwCJTQ1X
qXdKcEmktBrgZiSiTVFxxpQVhO/uB0HmzaZzrY1k1P5e6yhHEr422mcOcF9KcSL4
aeyRYHjoIh51vPMbScPjvfbO/PwooU3LWLlxLVNLG0MmkSaGyJeUXg/wHsGI910=
=JN0A
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-06-27 (Innova IPsec offload support)
This patchset adds support for Innova IPSec network interface card.
About Innova device:
--------------------
Innova is a network card with a ConnectX chip and an FPGA chip as a
bump-on-the-wire.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ I2C | | SBU | | +------+
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | Flash |
+-----+ +-------+
The FPGA synthesized logic is loaded from dedicated flash storage and has
access to its own dedicated DDR RAM.
The ConnectX chip firmware programs the FPGA by accessing its configuration
space over either the slow internal I2C link or the high-speed internal link.
The FPGA logic is divided into a "Shell" and a "Sandbox Unit" (SBU).
mlx5_core driver (with CONFIG_MLX5_FPGA) handles all shell functionality,
while other components may handle the various SBU functionalities.
The driver opens high-speed reliable communication channels with the shell and
the SBU over the internal link.
These channels may be used for high-bandwidth configuration or for SBU-specific
out-of-band data paths.
About Innova IPSec device:
--------------------------
Innova IPSec is a network card that allows offloading IPSec cryptography operations
from the host CPU to the NIC. It is an Innova card with an IPSec SBU.
The hardware keeps the database of IPSec Security Associations (SADB) in the FPGA's
DDR memory.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ Internal I2C | | IPSec | | +------+
| | SBU | |
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | |
| | | Flash |
|SADB | | |
+-----+ +-------+
Modes and ciphers:
Currently the following modes and ciphers are supported:
IPv4 and IPv6
ESP tunnel and transport modes
AES 128 and 256 bit encryption, with GCM authentication (RFC4106)
IV is generated using seqiv, in sync with Linux's geniv.
More modes and ciphers may be added later.
Notes:
In the future similar functionality will be included in a single-chip NIC.
About the driver:
-----------------
Patches 1-4 prepare some existing driver code for the new feature:
* Add support for reserved GIDs in the hardware GID table
* Allow multiple modules to enable hardware RoCE support independently
Patches 5-6 define structs and helper functions for QP work-queues.
Patches 7-11 add various FPGA-related features required for Innova.
IPSec.
Patch 12 adds abstraction layer for Mellanox IPSec-offload capable devices.
atches 13-16 add IPSec offload support to the mlx5 netdevice.
This driver services the new IPSec offload API introduced in commit
d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Configuration Path:
If Innova IPSec device is detected, the mlx5e netdevice gets the new
NETIF_F_HW_ESP feature and the xdo callbacks, indicating ESP offload
capabilities, and also the matching TX checksum and GSO features.
The driver configures offloaded Security Associations (SAs) by sending
an ADD_SA or DEL_SA message to the IPSec SBU, which updates the SADB in DDR.
These messages and their responses are sent over a high-speed channel.
Counters for ethtool are retrieved by the driver from the SBU.
Data path:
On receive path, the SBU decrypts ESP packets which match the offloaded SADB,
but keeps them encapsulated.
The SBU injects metadata (Mellanox owned ethertype) indicating that crypto-offload
has taken place, the SA with which it was done, and the authentication result.
The ConnectX chip performs RX checksum offload on the packet, and RSS using the
ESP SPI value. The driver detects the special ethertype, and attaches a struct
secpath to the RX SKB, including flags to indicate that crypto offload took place,
the authentication result, and which xfrm_state was used for decryption, in the
olen and ovec members. The RX SKB may have useful CHECKSUM_COMPLETE. A separate
patchset will add support for that in the xfrm stack.
On transmit path, the stack encapsulates the packet but does not encrypt it, and
indicates in the SKB's secpath that crypto offload is to be performed and the SA
to use to do so.
The driver avoids performing crypto-offload for ESP fragments, and packets with
IP options, as the SBU cannot currently do that. For eligible packets, the driver
prepends a special ethertype with metadata instructing the hardware to perform crypto offload.
The stack builds regular (non-GSO) SKBs so that they contain a placeholder for the ESP trailer.
The driver trims it off, because the SBU automatically appends the trailer for offloaded packets.
The ConnectX chip performs TX checksum offload on inner UDP or TCP packets,
and GSO for TCP packets (duplicating the prepended metadata).
The segmented packets then undergo encryption in the SBU before going on the wire.
Performance:
We measure single stream of TCP on Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz
Using AES-NI with ESP GSO we get constant 4.1 Gbps.
Using crypto offload we get constant 18 Gbps.
Note that these numbers require CHECKSUM_COMPLETE support in XFRM, which we submit separately.
- Ilan Tayari
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is cpts function to check if packet can be timstamped with cpts.
Seems that ptp_classify_raw cover all cases listed with "case".
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpts can timestmap only ptp packets at this moment, so driver
cannot mark every packet as though it's going to be timestamped,
only because h/w timestamping for given skb is enabled with
SKBTX_HW_TSTAMP. It doesn't allow to use sw timestamping, as result
outgoing packet is not timestamped at all if it's not PTP and h/w
timestamping is enabled. So, fix it by setting SKBTX_IN_PROGRESS
only for PTP packets.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sw timestamp function close to channel submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using netdev_<level>(netdev, "%s: ...", netdev->name) duplicates the
name in the output. Remove those uses.
Miscellanea:
o Use the netif_<level> convenience macros at the same time
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in mlx4_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in netif_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current way to find if the phy is internal is to compare DT phy-mode
and emac_variant/internal_phy.
But it will negate a possible future SoC where an external PHY use the
same phy mode than the internal one.
By using phy-mode = "internal" we permit to have an external PHY with
the same mode than the internal one.
Reported-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_options.c file contains multiple netdev_info statements that clutter kernel output.
This patch replaces all netdev_info with netdev_dbg and adds a netdev_dbg statement for the
packets per slave parameter. Also fixes misalignment at line 467.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael J Dilmore <michael.j.dilmore@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hostapd adds a station, it does so before sending the association
response frame, so that it can indicate the correct status code in the
response.
However, when this then fails, or the association response already is
a reject for some other reason, then there's no station entry and thus
no per-station management queue to send the response on and it must be
sent on the probe response queue. The code should therefore not warn.
In theory, we could check and warn if the status code is success, but
that seems excessive, so just relax the check to allow any association
response frames.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only a000-series devices were going to use this, but actually
initialize using the context info, which includes paging, so
this code is never invoked; remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we now support 8 device families, move their configuration
files into a new subdirectory "cfg".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This structure represents V2, V1 has the three last fields missing.
Rename it to be more accurate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the first frame on a given TID is received with seqno 0 and needed
to be retransmitted, we erroneously drop it because the deduplication
data is initialized to zero, and then comparing
if (unlikely(ieee80211_has_retry(hdr->frame_control) &&
dup_data->last_seq[tid] == hdr->seq_ctrl &&
dup_data->last_sub_frame[tid] >= sub_frame_idx))
return true;
will return in iwl_mvm_is_dup() since last_sub_frame is also set to
zero, and sub_frame_idx is usually zero since this only covers the
relatively rare case of A-MSDU.
Fix this by initializing the last_seq array to 0xffff, which is an
impossible value for hdr->seq_ctrl to have here because the lower
four bits are the fragment number, and fragments aren't handled in
this code but go to mac80211 instead.
Fixes: a571f5f635 ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In commit b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work
as expected"), the code was changed to make the stop conditional
on not having failed (and on not having init_dbg), which doesn't
make sense - we should stop the device regardless of failures.
Failure to do so is leading to the device being enabled when it
shouldn't be, and - if it gets re-enabled later - the new context
info code gets confused as paging data wasn't freed.
Remove the invalid error condition again.
Fixes: b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work as expected")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.
Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.
While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print out both queue IDs to be able to see what went wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new a000 2ax series and add
the five PCI ID for it.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no reason to pass mvm and trig as parameters to the macro,
since it will be expanded inside the function itself. Also remove the
bogus buf parameter which doesn't exist and is not used.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The sta_id variable is used as an index in an array, should be unsigned.
Found by Klocwork.
Fixes: 9f9af3d7d3 ("iwlwifi: mvm: re-aggregate shared queue after unsharing")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A hardware issue on 9000 series devices sometimes causes RF-kill
interrupts to not be propagated to the host properly if ASPM is
enabled. Work around this by setting the right hardware bit to
allow it to interrupt the host for this reason (rfkill).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a hardware issue, certain power saving had to be
disabled. However, this issue was fixed in B-step, so the
workaround only needs to apply to A-step.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some static checkers (e.g. smatch) complain if a non-constant
format string is used, even if that's a static const variable.
Since there's no impact on code generation, just change those
format strings to be macros.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the kernel-doc, and remove some fields even the firmware doesn't
use in ToF, RX, scan, station and generic FW APIS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix various "Excess struct/union/enum/typedef member '...' description
in '...'" warnings from kernel-doc, mostly caused by typos.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a debugfs entry to get a verbose description of the power settings
used in each band with the currently selected SAR geographic profile.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are going to add debugfs entry to retrieve the current geographic
profile being used in the FW. Currently the driver reads those tables
from the BIOS and passes them to the FW.
To prepare for this retrieving we want to store those
tables in the driver.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trivial fix to spelling mistake in mwifiex_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check return value from call to wl18xx_top_reg_write(),
so in case of error jump to goto label out and return.
Also, remove unnecessary value check before goto label out.
Addresses-Coverity-ID: 1226938
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kstrtoul() test was reversed so this always returned -ENOTSUPP.
Fixes: 27d7f47756 ("net: wireless: replace strict_strtoul() with kstrtoul()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Declare hwbus_ops structures as const as they are only passed as an
argument to the function cw1200_core_probe. This argument is of type
const. So, make these structures const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two recent commits added new RSI_FSM_STATES (namely FSM_FW_NOT_LOADED
and FSM_COMMON_DEV_PARAMS_SENT) and the corresponding table fsm_state
was not updated to match. This can lead to an array overrun when
accessing the latter two states in fsm_state. Fix this by adding in
the missing states.
Detected by CoverityScan, CID#1398379 ("Illegal address computation")
Fixes: 9920322ccd ("rsi: add tx frame for common device configuration")
Fixes: 015e367494 ("rsi: Register interrupt handler before firmware load")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 9cc4b7cb86 ("brcmfmac: Make skb header writable
before use") the headroom usage has been fixed. However, the
driver was keeping statistics that got lost. So reworking the
code so we get those driver statistics back for debugging.
Cc: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The statistic counter is used in common layer and in the bus layer
in different thread contexts so change to use atomic operations.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A couple of old fields were still described and one field was not
described.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When user adds a virtual interface driver will set the
bss_type to the iface_type given by the user. When
supplicant is started on the same interface, a call to
change_virtual_intf will be triggered if if_type is not
NL80211_IFTYPE_STATION. Here driver should not update
it's bss_type, because bss_type is intended to indicate
the original iface_type and changing the same will defeat
the purpose of creating this interface.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If wifi is in 4way, btcoex give wifi higher priority to use antenna.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are many AP (dirty environment), we use another strategy set
to resolve coex issue.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will use return value to handle error case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return value may be false in some situations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify 8723be and 8192e only.
8812/8821 do IQK in DM, so we may do it later.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this case, BTC asks to enter/leave PS mode frequently to cause A2DP
choppy.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value ret is unitialized and garbage is being returned
for the three different error conditions when setting up the PCIe
BARs. Fix this by initializing ret to -ENOMEM to indicate that
the BARs failed to be setup correctly.
Detected by CoverityScan, CID#1437563 ("Unitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Value assigned to variable offset at line 551 is overwritten at line 562,
before it can be used. This makes such variable assignment useless.
Addresses-Coverity-ID: 1226941
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the following spelling mistakes in messages:
syncronise -> synchronize
unusally -> unusually
addrress -> address
inverval -> interval
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move ath9k_rng_stop/ath9k_rng_start pair into critical section,
use mutex_lock to void potential race accessing.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the worst case, ath9k_rng_stop() may take 10s to stop rng kthread.
The time is too long for users, use wait_event_interruptible_timeout()
instead of msleep_interruptible(), wakup immediately once
kthread_should_stop() is true.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The hard coded register 0x9864 and 0x9924 are invalid
for ar9300 chips.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One scenario that could lead to UAF is two threads writing
simultaneously to the "tx99" debug file. One of them would
set the "start" value to true and follow to ath9k_tx99_init().
Inside the function it would set the sc->tx99_state to true
after allocating sc->tx99skb. Then, the other thread would
execute write_file_tx99() and call ath9k_tx99_deinit().
sc->tx99_state would be freed. After that, the first thread
would continue inside ath9k_tx99_init() and call
r = ath9k_tx99_send(sc, sc->tx99_skb, &txctl);
that would make use of the freed sc->tx99_skb memory.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAllTgG4ACgkQoUecoho8
xfopuBAAnRfYFrgZJ+hasZBNjaP2n1dc3wutnOMfly79owxUy7Iw7ekuo3MKZuxr
kLv7l02Zbo8hG9KO/sAvsjVNEIhnPrD1bUuY2DCJb5+ap2BWoFkA9+Z1nw5K1q2z
zD+nlAVE+v0rdmRe/gt6+s3kgQKahvqgotXJ/ObOuoaphQRm1VP22eVKl+XTG1gL
9NwmJ/ohuqwjVDVsv6ThTOq1pfbf0r065pUHrbSvCh7Wtus9KSloNajRbHhHjmz7
DG1Lop1bWTlEwYuGyJpFGwVt2hUcFb4sO6chzWhBxIeX/NBNHy+8ooY6dFbExgfD
++Co/HbMLZr9KRrIRxCkoe5Z1X5VaQR6rpUWLIWSvMrBb1CreBW4YdTdSdAPzk+n
MlyF2s3SxJkl/wvXCmwKsy02RX+X6ncbZ0/ihRoi+PAw4UI1sqbQN8y8/IlbNORc
fTBAqVpph+yyrUQoFlepSWTmVOGwKivbxEWZmKNpCbLBWMCA+nGwRbJnhMkj/bc2
Xkl17S4CTHD2basikiUiXjObKPPFw9c+ZuNgX+DnBD0qmyBilxgYuXRpaXRTPl1N
YbPygbEyiUeOzGS9fQcnLVEHVmvqRrFChD1eM6ag2nw2CVz5n57Zyu8j1QQQLq7F
Wsx7WE+sf/P48shVVkcXgCiZ7Bk10knSHC77ox4tH3PmLiVDNag=
=DdqX
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
More iwlwifi patches for 4.13
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
Give users an option not to build the flower-offload related code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we grab pf->lock around pci_enable_sriov() we can no longer
safely queue work which may also grab that lock onto system workqueue.
pci_enable_sriov() will flush system workqueue as part to wait for VF
probing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously assumed that app callback can be guaranteed to be
executed before SR-IOV is actually enabled. Given that we can't
guarantee that SR-IOV will be disabled during probe or that we
will be able to disable it on remove, we should reorder the callbacks.
We should also call the app's sriov_enable if SR-IOV was enabled
during probe.
Application FW must be able to disable VFs internally and not depend
on them being removed at PCIe level.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assumed that when we probe number of enabled VFs will be at 0.
This doesn't have to be the case for example if previous driver left
SR-IOV enabled due to some VFs being assigned. Read the number of VFs
enabled. Fail probe if it's above current FWs limit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make nfp_port_get_phys_port_name() support new port types and
wire it up to representors' struct net_device_ops.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on struct net_device_ops figure out if netdev is a nfp_repr.
Use this knowledge to convert netdev directly to nfp_port.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apps shouldn't declare their own struct net_device_ops for
representors, this makes sharing code harder. Add necessary
nfp_app callbacks and move the definition of representors'
struct net_device_ops to common code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to the fact that all representors will now have an nfp_port,
we can depend on information there to provide a app-independent
.ndo_get_stats64().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_port is an abstraction which is supposed to allow us sharing
code between different netdev types (vNIC vs repr). Spawn ports
for PFs and VFs to enable this sharing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a cleanup callback for undoing what app init callback did.
Make flower allocate its private structure on init and free
it from the new callback.
While at it remember to set the app pointer to NULL on the
error path to avoid any races while probe path unwinds.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused nfp_cpp_area_check_range() function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move most of the helper for mapping RTsyms from nfp_net_main.c
to nfpcore. Use the new helper directly for mapping MAC statistics,
since they don't need to include the PCIe interface ID in the symbol
name.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_net_map_area() is a helper for mapping areas of NFP memory
defined in nfp_net_main.c. Move it to nfpcore to allow reuse
and rename accordingly. Create an additional helper -
nfp_cpp_area_alloc_acquire() the opposite of already existing
nfp_cpp_area_release_free().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We support application FW being either loaded automatically at
boot from flash or (more commonly) by the driver from disk.
If FW is not found on disk and nothing is preloaded users are
faced with this unintuitive error:
nfp 0000:04:00.0: nfp: Failed to find PF symbol _pf0_net_bar0
We can do better. Since we rely on symbol table being present -
check early if it could be correctly read out of from the device
and if not print a more informative message.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Belkin B2B128 is a USB 3.0 Hub + Gigabit Ethernet Adapter, the
Ethernet adapter uses the ASIX AX88179 USB 3.0 to Gigabit Ethernet
chip supported by this driver, add the USB ID for the same.
This patch is based on work by Geoffrey Tran <geoffrey.tran@gmail.com>
who has indicated they would like this upstreamed by someone more
familiar with the upstreaming process.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit (5567e98919) inserted a dependency on DMA
API that requires HAS_DMA to be added in Kconfig.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The access to the wrong variable could lead to a NULL dereference and
possibly other invalid memory reads in vxlan newlink/changelink requests
with a IFLA_MTU attribute.
Fixes: a985343ba9 "vxlan: refactor verification and application of configuration"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'wiphy_new()' fails, we leak 'ops'. Add a new label in the error
handling path to free it in such a case.
Cc: stable@vger.kernel.org
Fixes: 5c22fb8510 ("brcmfmac: add wowl gtk rekeying offload support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_net_attach() can only fail when register_netdevice()
fails. When this happens register_netdevice() calls priv_destructor, ie.
brcmf_cfg80211_free_netdev() freeing the vif instance. Also upon this
failure brcmf_net_attach() calls free_netdev(). However, callers are also
doing cleanup resulting in double free. In some places they need netdev
private space as it holds parameters to communicate with the device. So
we want to do the cleanup only in callers of brcmf_net_attach() by making
the following changes:
- set priv_destructor after register_netdevice() succeeds.
- remove call to free_netdev() in brcmf_net_attach().
- call free_netdev() in brcmf_net_detach() for unregistered netdev.
- add free_netdev() if brcmf_net_attach() fails for a created interface.
Fixes: cf124db566 ("net: Fix inconsistent teardown and release of private netdev state.")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the TX data path, prepend a special metadata ethertype which
instructs the hardware to perform cryptography.
In addition, fill Software-Parser segment in TX descriptor so
that the hardware may parse the ESP protocol, and perform TX
checksum offload on the inner payload.
Support GSO, by providing the inverse of gso_size in the metadata.
This allows the FPGA to update the ESP header (seqno and seqiv) on the
resulting packets, by calculating the packet number within the GSO
back from the TCP sequence number.
Note that for GSO SKBs, the stack does not include an ESP trailer,
unlike the non-GSO case.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In RX data path, the hardware prepends a special metadata ethertype
which indicates that the packet underwent decryption, and the result of
the authentication check.
Communicate this to the stack in skb->sp.
Make wqe_size large enough to account for the injected metadata.
Support only Linked-list RQ type.
IPSec offload RX packets may have useful CHECKSUM_COMPLETE information,
which the stack may not be able to use yet.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add Innova IPSec ESP crypto offload configuration paths.
Detect Innova IPSec device and set the NETIF_F_HW_ESP flag.
Configure Security Associations using the API introduced in a previous
patch.
Add Software-parser hardware descriptor layout
Software-Parser (swp) is a hardware feature in ConnectX which allows the
host software to specify protocol header offsets in the TX path, thus
overriding the hardware parser.
This is useful for protocols that the ASIC may not be able to parse on
its own.
Note that due to inline metadata, XDP is not supported in Innova IPSec.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add routines for manipulating the hardware IPSec SA database (SADB).
In Innova IPSec, a Security Association (SA) is added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova IPSec (FPGA-based) hardware.
These routines will be used by the IPSec offload support in a later patch
However they may also be used by others such as RDMA and RoCE IPSec.
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In this patchset we add Innova IPSec support and mlx5/accel delegates
IPSec offloads to Innova routines.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.
A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.
Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.
At high level, the FPGA configuration space is divided such:
0x00000000 - 0x007fffff is reserved for the SBU
0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ... is DDR memory
A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The Innova FPGA includes shell hardware and Sandbox-Unit (SBU) hardware.
The shell hardware is handled by mlx5_core itself, while the SBU is
handled by a client driver.
Reset the SBU to a well-known initial state when initializing a new
device, and set the FPGA to bypass mode when uninitializing a device.
This allows the client driver to assume that its device has been
reset when a new device is detected.
During SBU reset, the FPGA is put into SBU-bypass mode. In this mode
packets do not pass through the SBU, so it cannot affect the network
data stream at all.
A factory-image does not have an SBU, so skip these flows.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
An FPGA high-speed connection has two endpoints, an FPGA QP and a
ConnectX QP.
Add library routines to create and connect the endpoints of an
FPGA high-speed connection.
These routines allow creating and interacting with both types of
connections: Shell and Sandbox Unit (SBU).
Shell connection provides an interface to the FPGA's address space,
which includes the configuration space and the DDR.
Use of the shell connection will be introduced in a later patchset.
SBU connection provides a command and/or data interface to the
application-specific logic within the FPGA.
Use of the SBU connection will be introduced in a later patch in
this patchset.
Some struct definitions are added to a new header file sdk.h, which
will be extended in later patches in the patchset.
This header file will contain the in-kernel FPGA client driver API.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.
Add ConnectX FW commands which create and manipulate FPGA QPs.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FPGA init and cleanup routines should be called just once per
device.
Move them to the init_once and cleanup_once routines.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A QP in ConnectX is a concatenation of RQ and SQ which share a QP-number
and work together.
Add support for allocating and managing the work-queue buffer for a QP, in
a similar way to how SQs and RQs are already supported.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move mlx5e_get_cqe routine to wq.h and rename it to
mlx5_cqwq_get_cqe.
This allows it to be used by other CQ users outside of the
ethernet driver code.
A later patch in this patchset will make use of it from
FPGA code for the FPGA high-speed connection.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previously, only mlx5_ib enabled RoCE on the port, but FPGA needs it as
well.
Add support for counting number of enables, so that FPGA and IB can work
in parallel and independently.
Program the HW to enable RoCE on the first enable call, and program to
disable RoCE on the last disable call.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reserved GIDs are entries in the GID table in use by the mlx5_core
and its submodules (e.g. FPGA, SRIOV, E-Swtich, netdev).
The entries are reserved at the high indexes of the GID table.
A mlx5 submodule may reserve a certain amount of GIDs for its own use
during the load sequence by calling mlx5_core_reserve_gids, and must
also take care to un-reserve these GIDs when it closes.
Reservation is only allowed during the load sequence and before any
interfaces (e.g. mlx5_ib or mlx5_en) are up.
After reservation, a submodule may call mlx5_core_reserved_gid_alloc/
free to allocate entries from the reserved GIDs pool.
Reserve a GID table entry for every supported FPGA QP.
A later patch in the patchset will remove them from being reported to
IB core.
Another such patch will make use of these for FPGA QPs in Innova NIC.
Added lib/mlx5.h to serve as a library for mlx5 submodlues, and to
expose only public mlx5 API, more mlx5 library files will be added in
future submissions.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In load_one, the interface flags are changed from down to up,
only after initializing the interfaces.
In unload_one, the flags are changed from up to down before the
interface cleanup.
Change the cleanup order to be opposite to initialization order.
This fixes flag consistency between init and cleanup.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Symbol error during carrier counter from PPCNT was mistakenly reported as
TX carrier errors in get_stats ndo, although it's an RX counter.
Fixes: 269e6b3af3 ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Draining the health workqueue will ignore future health works including
the one that report hardware failure and thus we can't enter error state
Instead cancel the recovery flow and make sure only recovery flow won't
be scheduled.
Fixes: 5e44fca504 ('net/mlx5: Only cancel recovery work when cleaning up device')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When wait for firmware init fails, previous code would mistakenly
return success and cause inconsistency in the driver state.
Fixes: 6c780a0267 ("net/mlx5: Wait for FW readiness before initializing command interface")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Trivial fix to spelling mistake in en_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the MACB is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
=Fd/c
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On emulation systems, the EMAC's internal PHY ("SGMII") is not present,
but is not needed for network functionality. So just display a warning
message and ignore the SGMII.
Tested-by: Philip Elcan <pelcan@codeaurora.org>
Tested-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ACPI systems, the driver depends on firmware pre-initializing the
EMAC because we don't have access to the clocks, and the EMAC has specific
clock programming requirements. Therefore, we don't want to reset the
EMAC while we are completing the initialization.
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shutdown function halts all DMA and interrupts, so that all
operations are discontinued when the system shuts down, e.g. via
kexec or a forced reboot.
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're accidentally returning the wrong variable. "cmode" is
uninitialized at this point so it causes a static checker warning.
Fixes: 6335e9f244 ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialise VF and PF representors in flower app.
Based in part on work by Benjamin LaHaise, Bert van Leeuwen and
Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add app for flower offload. At this point the PF netdev and phys port
representor netdevs are initialised. Follow-up work will add support for
VF and PF representors and beyond that offloading the flower classifier.
Based in part on work by Benjamin LaHaise and Bert van Leeuwen.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding a new flower app - targeted at offloading
the flower classifier - provide support for control message that it will
use to communicate with the NFP.
Based in part on work by Bert van Leeuwen.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow tx/rx with metadata port id. This will be used for tx/rx of
representor netdevs acting as upper-devices while a pf netdev acts
as a lower-device.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide port rather than vNIC as parameter of nfp_net_get_mac_addr.
This is to allow this function to be used by representor netdevs where
a vNIC may have more than one physical port none of which are associated
with the vNIC.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add app-callbacks for app-specific initialisation of SRIOV.
Disabling SRIOV is brought forward in nfp_pci_remove()
so that nfp_app_sriov_disable is called while the app still exists.
This is intended to be used to implement representor netdevs for virtual
ports.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide helpers for stats and xmit on representor netdevs.
Parts based on work by Bert van Leeuwen, Benjamin LaHaise and
Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide infrastructure to create and destroy representors of a given type.
Parts based on work by Bert van Leeuwen, Benjamin LaHaise,
and Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If present map mac_stats and vf_cfg BARs. These will be used by
representor netdevs to read statistics for phys port and vf representors.
Also provide defines describing the layout of the mac_stats area.
Similar defines are already present for the cf_cfg area.
Based in part on work by Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MAC/PHY port init into a helper to make it easier to reuse
it in the representor code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add app callback for reporting eswitch mode. Non-SRIOV apps
should not implement this callback, nfp_app code will then
respond with -EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mc configuration changes bnx2x_config_mcast() can return 0 for
success, negative for failure and positive for benign reason preventing
its immediate work, e.g., when the command awaits the completion of
a previously sent command.
When removing all configured macs on a 578xx adapter, if a positive
value would be returned driver would errneously log it as an error.
Fixes: c7b7b483cc ("bnx2x: Don't flush multicast MACs")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To handle netpoll properly, the driver must only handle TX packets
during NAPI. Handling RX events cause warnings and errors in
netpoll mode. The ndo_poll_controller() method should call
napi_schedule() directly so that a NAPI weight of zero will be used
during netpoll mode.
The bnxt_en driver supports 2 ring modes: combined, and separate rx/tx.
In separate rx/tx mode, the ndo_poll_controller() method will only
process the tx rings. In combined mode, the rx and tx completion
entries are mixed in the completion ring and we need to drop the rx
entries and recycle the rx buffers.
Add a function bnxt_force_rx_discard() to handle this in netpoll mode
when we see rx entries in combined ring mode.
Reported-by: Calvin Owens <calvinowens@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we get a TPA_END completion to handle a completed LRO packet, it
is possible that hardware would indicate errors. The current code is
not checking for the error condition. Define the proper error bits and
the macro to check for this error and abort properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, skb_complete_tx_timestamp(), used to allow passing in a
NULL pointer for the time stamps, but that was changed in commit
62bccb8cdb ("net-timestamp: Make the
clone operation stand-alone from phy timestamping"), and the existing
call sites, all of which are in the dp83640 driver, were fixed up.
Even though the kernel-doc was subsequently updated in commit
7a76a021cd ("net-timestamp: Update
skb_complete_tx_timestamp comment"), still a bug fix from Manfred
Rudigier came into the driver using the old semantics. Probably
Manfred derived that patch from an older kernel version.
This fix should be applied to the stable trees as well.
Fixes: 81e8f2e930 ("net: dp83640: Fix tx timestamp overflow handling.")
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides some updates to the mlx5 core and netdevice drivers.
Three patches from Tariq, Introduces page reuse mechanism in non-Striding
RQ RX datapath, we allow the the RX descriptor to reuse its allocated page
as much as it could, until the page is fully consumed. RX page reuse
reduces the stress on page allocator and improves RX performance especially
with high speeds (100Gb/s).
Next four patches of the series from Or allows to offload tc flower matching
on ttl/hoplimit and header re-write of hoplimit.
The rest of the series from Yotam and Or enhances mlx5 to support FW flashing
through the mlxfw module, in a similar manner done by the mlxsw driver.
Currently, only ethtool based flashing is implemented, where both Eth and IB ports
are supported.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZTR2/AAoJEEg/ir3gV/o+HHkH/jA8uoIQgsIKP8+D6ppwChCm
pcNpNWi5eWjBwRbeDKqTVRtmKEapFf2bjhWaegsybr7oGhzyh+t6nvCEiJVoKLpd
gmcSKy7nY2PSepuMEg7bqlfj5caS3b0Nlz5sqPdclOXKYDVLytvcelOvr9OnqdAT
JqxWkJMhEpLSgFniuvIyc1uJq9j6ARW7SYWx/dKp+gTDI2KCwQ3DinsrZ+RPh42F
rxLFhGkcFuQ5cIr3QIdCM+pbr6LlAf2Fvz1Y791BARZg0XZp149C0c4smieEjU9M
ya9CWlbSvnsYZcSMXtUO8ETnrtvrEfcEM0MpZo8l4y28eWih/Ib5BiHevQG3wHA=
=L44M
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-06-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-06-23
This series provides some updates to the mlx5 core and netdevice drivers.
Three patches from Tariq, Introduces page reuse mechanism in non-Striding
RQ RX datapath, we allow the the RX descriptor to reuse its allocated page
as much as it could, until the page is fully consumed. RX page reuse
reduces the stress on page allocator and improves RX performance especially
with high speeds (100Gb/s).
Next four patches of the series from Or allows to offload tc flower matching
on ttl/hoplimit and header re-write of hoplimit.
The rest of the series from Yotam and Or enhances mlx5 to support FW flashing
through the mlxfw module, in a similar manner done by the mlxsw driver.
Currently, only ethtool based flashing is implemented, where both Eth and IB ports
are supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffer group mappings can be obtained using FW_PARAMs cmd for newer FW.
Since some of the bg_maps are obtained in atomic context, created another
t4_query_params_ns(), that wont sleep when awaiting mbox cmd completion.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using t4_get_mps_bg_map() for both t4_get_port_stats()
to determine which MPS Buffer Groups to report statistics on for a given
Port, and also for t4_sge_alloc_rxq() to provide a TP Ingress Channel
Congestion Map. For T4/T5 these are actually the same values (because they
are ~somewhat~ related), but for T6 they should return different values
(T6 has Port 0 associated with MPS Buffer Group 0 (with MPS Buffer Group 1
silently cascading off) and Port 1 is associated with MPS Buffer Group 2
(with 3 cascading off)).
Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx drop counter is reported by the device in the keep-alive
event.
update the driver's counter with the device counter.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ena_com_mem_addr_set(), use the above functions to split dma address
to the lower 32 bits and the higher 16 bits.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver tries to allocate msix vectors as the number of the
negotiated io queues. (with another msix vector for management).
If pci_alloc_irq_vectors() fails, the driver aborts the probe
and the ENA network device is never brought up.
With this patch, the driver's logic will reduce the number of IO
queues to the number of allocated msix vectors (minus one for management)
instead of failing probe().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA driver post Rx buffers through the Rx submission queue
for the ENA device to fill them with receive packets.
Each Rx buffer is marked with req_id in the Rx descriptor.
Newer ENA devices could consume the posted Rx buffer in out of order,
and as result the corresponding Rx completion queue will have Rx
completion descriptors with non contiguous req_id(s)
In this change the driver holds two rings.
The first ring (called free_rx_ids) is a mapping ring.
It holds all the unused request ids.
The values in this ring are from 0 to ring_size -1.
When the driver wants to allocate a new Rx buffer it uses the head of
free_rx_ids and uses it's value as the index for rx_buffer_info ring.
The req_id is also written to the Rx descriptor
Upon Rx completion,
The driver took the req_id from the completion descriptor and uses it
as index in rx_buffer_info.
The req_id is then return to the free_rx_ids ring.
This patch also adds statistics to inform when the driver receive out
of range or unused req_id.
Note:
free_rx_ids is only accessible from the napi handler, so no locking is
required
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each device reset, log to the device what is the cause
the reset occur.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using:
memset(ptr, 0x0, sizeof(struct ...))
use:
memset(ptr, 0x0, sizeor(*ptr))
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, ENA device can update the ena driver about
the desired timeout values:
These values are part of the "hardware hints" which are transmitted
to the driver as Asynchronous event through ENA async
event notification queue.
In case the ENA device does not support this capability,
the driver will use its own default values.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions dwmac4_dma_init_rx_chan, dwmac4_dma_init_tx_chan and
dwmac4_dma_init_channel do not need to be in global scope, so them
static.
Cleans up sparse warnings:
"symbol 'dwmac4_dma_init_rx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_tx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_channel' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of just added XDP_ATTACHED_HW.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the XDP_FLAGS_HW_MODE. When it's set install the program
on the NIC and skip enabling XDP in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xdp_prog member of the adapter's data path structure is used
for XDP in driver mode. In case a XDP program is loaded with in
HW-only mode, we need to store it somewhere else. Add a new XDP
prog pointer in the main structure and use that when we need to
know whether any XDP program is loaded, not only a driver mode
one. Only release our reference on adapter free instead of
immediately after netdev unregister to allow offload to be disabled
first.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRV_MODE means that user space wants the program to be run in
the driver. Do not try to offload. Only offload if no mode
flags have been specified.
Remember what the mode is when the program is installed and refuse
new setup requests if there is already a program loaded in a
different mode. This should leave it open for us to implement
simultaneous loading of two programs - one in the drv path and
another to the NIC later.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of XDP offload flags move the driver setup into
a function. Otherwise the number of conditions in one function
would make it slightly hard to follow. The offload handler may
now be called with NULL prog, even if no offload is currently
active, but that's fine, offload code can handle that.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to TX through a monitor interface, the
conditions in iwl_mvm_tx_skb_non_sta() don't match
and the frame tries to go out from an usued TXQ.
Add a check for monitor iface, and use the AUX queue
in such a case.
In non-DQA mode the frame is sent through the
static-allocated queues anyway, so the problem is
in DQA mode only.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
