The ADSP code should be agnostic of which CODEC it runs upon, currently
there is only one remaining part of the implementation that doesn't
follow this. When the DSP is booted on ADSP2 we read
ARIZONA_SYSTEM_CLOCK_1 and use that to set the initial speed for the DSP
clock. This patch factors that out into CODEC specific code, leaving the
ADSP code entirely CODEC agnostic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Data is read in blocks of up to one fragment is size from the circular
buffer on the DSP and is re-packed to remove the padding byte that
exists in the DSP memory map.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here support is added for responding to DSP IRQs that are used to
indicate data being available on the DSP. The idea is that we check the
amount of data available upon receipt of an IRQ and on subsequent calls
to the pointer callback we recheck once less than one fragment is
available (to avoid excessive SPI traffic), if there is truely less than
one fragment available we ack the last IRQ and wait for a new one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream is created whilst the compressed stream is opened and a
buffer is created when the DSP powers up. It is necessary at a point
once both the DSP has powered up and the the stream has been opened to
connect a stream to a buffer on the DSP. This is done in the trigger
callback as this is after the DSP has been powered and obviously the
stream must be open. Note that whilst the connect is currently trivial
it is expected that this will get more complex when support for multiple
buffers/streams per DSP is added.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code that locates and initialises the buffer of compressed data on
the DSP if the firmware supported compressed data capture. The buffer
struct (wm_adsp_compr_buf) is kept separate from the stream struct
(wm_adsp_compr) this will allow much easier support of multiple
streams of data from the one DSP in the future, although support for
this will not be added in this patch chain.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow user-space to open a compressed stream, although no data will be
passed yet, as part of this adding the ability to define supported
capabilities per firmware and check these match the stream being opened.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most events around the DSP just need to be locked to ensure that the DSP
can't change power state whilst they are happening. This includes the
debugfs entries and this will make sorting the rest of the locking
simpler.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rate controls are codec-specific, it's not possible to
generically say what the range or the meaning of each control
is (or even if they exist at all) - that depends on the
particular codec.
This is currently being handled for Arizona codecs by putting
an Arizona-specific table of controls inside the wm_adsp driver.
This creates a dependency between wm_adsp and arizona.c, and is an
awkward solution if the ADSP is used in another family of codecs
Fix this by moving the Arizona-specific rate controls into the
Arizona codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds some debugfs nodes to get information
about the currently running firmware.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have a codec_probe stage initialization in the wm_adsp
driver, we can make the wm_adsp driver create its own ALSA controls
instead of having that responsibility pushed to every codec driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the only init function in wm_adsp is called by the
codec driver early in its probe before the codec has been
registered with SOC.
This patch adds stubs for the codec_probe and codec_remove stages
and calls them from WM5102 and WM5110 codec drivers. This allows us
to hang anything that needs setup during the codec probe stage off
these functions without further modification of the codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In theory the ADSP driver should not need to know anything
about the codec it is part of. But the WM5102 needs DVFS
control based on ADSP clocking speed. This was being handled
by bundling part of the knowledge of this into the ADSP driver.
This change moves this handling out of the ADSP driver and
into the WM5102 driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Revision one of the file format includes new algorithm and coefficient
blocks which provide additional information about the controls exported
by the firmware. This patch updates the processing to handle this
version of the file format. Note that whilst this version of the format
adds support for specifying a name for the control through the firmware
file this has not been used and to keep compatibility with existing
deployments no changes to the firmware control naming are made by this
patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The algorithm region information in the firmware doesn't contain a
length field, explicitly pass this to the create_control function rather
than bundling into wm_adsp_alg_region.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have wm_adsp_region, wm_adsp_alg_region, and wmfw_region, the
variables for which are all frequently called region, this can get quite
confusing when reviewing the code especially given some functions are
quite long. Consistently use mem for wm_adsp_regions, alg_region for
wm_adsp_alg_region and region for wmfw_region.
Additionally, we use a mix of adsp and dsp for pointers to the wm_adsp
structure standardise this on dsp.
Finally, we use algs to refer to the number of algorithms quite
frequently, change this to the more descriptive n_algs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the start of booting the DSP to earlier in the DAPM process, and
move the final starting of the DSP to later in the DAPM process. This
allows us to overlap some of the processing with other components of the
system being brought up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the ADSP2 boot proceedure into a work structure in preparation for
running it asynchronously with the reset of the audio path bring up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to hold on to the `codec' pointer. We can use the `dsp'
pointer and grab all the information we need from there. This
makes the parameters for the functions a bit more sane and idiomatic.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Get rid off the wm_coeff struct and the wm_coeff_add_kcontrol()
function. We are now using the snd_soc_card_kcontrol() function to
get the kcontrol pointers. No need to call into ALSA code to
register the kcontrols.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add initial support for runtime tuning for the ADSP cores. This
is achieved by exposing the coefficient configuration blocks as
ALSA binary controls.
The current code assumes that no controls on the DSP are volatile.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we have regular register mapped controls we should be splitting
the control sets for ADSP1 and ADSP2 as the register maps are not
identical. Do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Older .bin files report the global coefficients as absolute address writes
to zero; maintain compatibility with them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sets the ADSP1 clock rate to match the system clock
rate. To support this the codec driver provides
details of register containing the system clock
control bits.
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are many firmwares available for ADSP devices. Add basic support
for selecting between them, including a couple of feature sets in the
set of available firmware to start off with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
WMDR coefficient files can specify coefficients in terms of algorithm
specific data regions. Record the start addresses of these regions while
parsing the algorithms and then use them to handle coefficients with
these formats.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some ADSP devices can make use of DVFS to optimise power consumption
depending on the operating frequency of the DSP core. Implement
support for this in the generic ADSP code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many current Wolfson devices feature DSPs based around an architecture
known as ADSP. Since there is a lot of commonality in the system
integration of these devices a common library will be used to provide
support for them.
This version provides equivalent support for ADSP1 to that currently
included in the WM2200 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
