Sienna_cichlid has four sdma instances, but other chips don't.
So we need expand to add multiple trap event irq id in sdma
v5.2.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.Skip decode_ring test in VF, because VCN in SRIOV does not
support direct register read/write.
2.Skip powergating configuration in hw fini because
VCN3.0 SRIOV doesn't support powergating.
V2: delete unneccessary white lines and refine implementation.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.In early_init and for sriov, hardcode
harvest_config=0, enc_num=1
2.sw_init/fini
alloc & free mm_table for sriov
doorbell setting for sriov
3.hw_init/fini
Under sriov, add start_sriov to config mmsch
Skip ring_test to avoid mmio in VF, but need to initialize wptr for vcn rings.
4.Implementation for vcn_v3_0_start_sriov
V2:Clean-up some uneccessary funciton declaration.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For VCN3.0 SRIOV, Guest driver needs to communicate with mmsch
to set the World Switch for MM appropriately. This patch add
the interface for mmsch_v3.0.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For gfx10 boards, except for nv12, other boards take mmio write
rather than rlcg write
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SIENNA_CICHLID SRIOV, jpeg and pgcp is not supported.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leftover of previous cleanups.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Put the common code in smu_v11_0.c instead of having one copy each.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This can help to maintain clear code layer.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As it's needed in the succeeding thermal irq setting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are needed for temp1/2/3 related hwmon interfaces.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are needed for temp1/2/3 related hwmon interfaces.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The LCLK dpm table setup should be performed in .update_pcie_parameters().
Otherwise, the updated GenSpeed and LaneCount information will be lost.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This can also help to maintain clear code layer.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leftover of previous performance level setting cleanups.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By calling the target APIs directly.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before and after setting gfx clock soft max/min frequency.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the common smu_v11_0_set_soft_freq_limited_range.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As a common performance level setting API is used. Then these
ASIC specific APIs are not needed any more.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As a common performance level setting API is used. Then these
ASIC specific APIs are not needed any more.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As a common performance level setting API is used. Then these
ASIC specific APIs are not needed any more.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that it can be more widely shared around SMU v11 ASICs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Preparing for coming code sharing around performance level
setting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is used to cache the clock frequencies for all UMD pstates.
So that we do not need to calculate from scratch on every UMD
pstate switch.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cache all clocks levels for every dpm table. They are needed
by other APIs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cache all clocks levels for every dpm table. They are needed
by other APIs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Preparing for coming code sharing around performance level
setting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maximum the code sharing around smu V11.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These members can help to cache the clock frequencies for all
dpm levels. Then simplifying the code for dpm level switching
is possible.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we are in RAS triggered situation and
BACO isn't support, emergency restart is needed,
and this code is only needed for some specific
cases(vega20 with given smu fw version).
After we add smu mode1 reset for sienna cichlid, we
need to share AMD_RESET_METHOD_MODE1 with psp mode1 reset,
so in amdgpu_device_gpu_recover, we need differentiate
which mode1 reset we are using, then decide if it's
a full reset and then decide if emergency restart is needed,
the logic will become much more complex.
After discussion with Hawking, move emergency restart logic
to an independent function.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Wenhui Sheng <Wenhui.Sheng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- fix some styling issues
- fixes for kernel-doc type
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "stream" pointer can't be NULL and it's dereferenced on the line
before so the check doesn't make sense.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
"u64 *wptr" points to the the wptr value in write back buffer and
"*wptr = (*wptr) >> 2;" results in the value being overwritten each time
when ->get_wptr() is called.
umr uses /sys/kernel/debug/dri/0/amdgpu_ring_sdma0 to get rptr/wptr and
decode ring content and it is affected by this issue.
fix and simplify the logic similar as sdma_v4_0_ring_get_wptr().
v2: fix for sdma5.2 as well
Suggested-by: Le Ma <le.ma@amd.com>
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to easily add new debugfs file w/o changing the hardcoded list count.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I consulted Cai Land(Chuntian.Cai@amd.com), he told me corresponding smc
message name to fSMC_MSG_SetWorkloadMask() is
"PPSMC_MSG_ActiveProcessNotify" in firmware code of Renoir.
Strange though it may seem, but it's a fact.
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CRC capture doesn't work when the active plane count is 0 since we
currently tie both vblank and pageflip interrupts to active_plane_count
greater than 0.
[How]
The frontend is what generates the vblank interrupts while the backend
is what generates pageflip interrupts. Both have a requirement for
the CRTC to be active, so control the overall interrupt state based
on that instead.
Pageflip interrupts need to be enabled based on active plane count, but
we actually rely on power gating to take care of disabling the interrupt
for us on pipes that can be power gated.
For pipes that can't be power gated it's still fine to leave it enabled
since the interrupt only triggers after the address has been written
to that particular pipe - which we won't be doing without an active
plane.
The issue we had before with this setup was that we couldn't force
the state back on. We were essentially manipulating the refcount
to enable or disable as needed in a two pass approach.
However, there is a function that solves this problem more elegantly:
amdgpu_irq_update() will unconditionally call the set based on what it
thinks the current enablement state is.
This leaves two future TODO items for our IRQ handling:
- Disabling IRQs in commit tail instead of atomic commit
- Mapping the pageflip interrupt to VUPDATE or something that's tied to
the frontend instead of the backend since the mapping to CRTC is not
correct
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling the debugfs for CRC capture we hit assertions caused by
register address and field masks and shifts missing.
[How]
We want these registers programmed, so add in the SRI/SF entries for
this register.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Failing to allocate a transfer function during stream construction leads
to a null pointer dereference
[How]
Handle the failed allocation by failing the stream construction
Cc: stable@vger.kernel.org
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move code for parsing debugfs input into an array of int parameters by
specifying the max number of expected parameters
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our validation is a known mess with actual validation mixed with
topology configuration. This change makes sure topolgical validation is
completed before any topology changes are made so we do not run into
issues where we merge and split a pipe over the course of a single call.
v2: Squash in compilation fix
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new calculated dispclk, dppclk are stored in
context->bw_ctx.bw.dcn.clk.dispclk_khz, dppclk_khz. Current dispclk,
dppclk are from dc->clk_mgr->clks.dispclk_khz. dcn_validate_bandwidth
compute new dispclk, dppclk. dispclk will put in use after
optimize_bandwidth when ramp_up_dispclk_with_dpp is called. There are
two places for dppclk be put in use. One location is the same as the
location as dispclk. Another is within update_dchubp_dpp which happens
between pre_bandwidth and optimize_bandwidth. dppclk updated within
update_dchubp_dpp will cause new clock values of dispclk and dppclk not
be in use at the same time. when clocks are decreased, this may cause
dppclk is lower than current configuration and let pipe stuck. for
example, eDP + external dp, change resolution of DP from 1920x1080x144hz
to 1280x960x60hz.
before change: dispclk = 337889 dppclk = 337889
change mode, dcn_validate_bandwidth calculate
dispclk = 143122 dppclk = 143122
update_dchubp_dpp be executed before dispclk be updated,
dispclk = 337889, but dppclk use new value dispclk /2 =
168944. this will cause pipe pstate warning issue.
[How]
between pre_bandwidth and optimize_bandwidth, while dispclk is going to
be decreased, keep dppclk = dispclk
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
