Pending tables for the redistributors are currently allocated
one at a time as each CPU boots. This is causing some grief
for Linux/RT (allocation from within a CPU hotplug notifier is
frown upon).
Let's move this allocation to take place at init time, when we
only have a single CPU. It means we're allocating memory for CPUs
that are not online yet, but most system will boot all of their
CPUs anyway, so that's not completely wasted.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're going to reuse some pre-allocated memory for the property
table, split out the zeroing of that table into a separate function
for later use.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
LPI_PENDING_SZ is always used in conjunction with a max(), which doesn't
make much sense, since we're guaranteed that LPI_PENDING_SZ is already
aligned to 64K. Let's remove it.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit fe8e93504c ("irqchip/gic-v3-its: Use full range of LPIs"), removes
the cap for lpi_id_bits, which causes the following warning to trigger on a
QDF2400 server:
WARNING: CPU: 0 PID: 0 at mm/page_alloc.c:4066 __alloc_pages_nodemask
...
Call trace:
__alloc_pages_nodemask+0x2d8/0x1188
alloc_pages_current+0x8c/0xd8
its_allocate_prop_table+0x5c/0xb8
its_init+0x220/0x3c0
gic_init_bases+0x250/0x380
gic_acpi_init+0x16c/0x2a4
In its_alloc_lpi_tables(), lpi_id_bits is 24 in QDF2400. The allocation in
allocate_prop_table() tries therefore to allocate 16M (order 12 if
pagesize=4k), which triggers the warning.
As said by MarcL
Capping lpi_id_bits at 16 (which is what we had before) is plenty,
will save a some memory, and gives some margin before we need to push
it up again.
Bring the upper limit of lpi_id_bits back to prevent
Fixes: fe8e93504c ("irqchip/gic-v3-its: Use full range of LPIs")
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jia He <jia.he@hxt-semitech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lkml.kernel.org/r/1535432006-2304-1-git-send-email-jia.he@hxt-semitech.com
The its_lock lock is held while a new device is added to the list and
during setup while the CPU is booted. Even on -RT the CPU-bootup is
performed with disabled interrupts.
Make its_lock a raw_spin_lock_t.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A recent extension to the GIC architecture allows a hypervisor to
arbitrarily reduce the number of LPIs available to a guest, no
matter what the GIC says about the valid range of IntIDs.
Let's factor in this information when computing the number of
available LPIs
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of exposing the GIC distributor IntID field in the rdist
structure that is passed to the ITS, let's replace it with a
copy of the whole GICD_TYPER register. We are going to need
some of this information at a later time.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At the moment, the core ITS driver imposes the allocation to be
in chunks of 32. As we want to relax this on a per bus basis, let's
move the the the allocation constraints to each bus.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we used to represent the LPI range using a bitmap, we were reducing
the number of LPIs to at most 64k in order to preserve memory.
With our new allocator, there is no such need, as dealing with 2^16
or 2^32 LPIs takes the same amount of memory.
So let's use the number of IntID bits reported by the GIC instead of
an arbitrary limit.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Our current LPI allocator relies on a bitmap, each bit representing
a chunk of 32 LPIs, meaning that each device gets allocated LPIs
in multiple of 32. It served us well so far, but new use cases now
require much more finer grain allocations, down the the individual
LPI.
Given the size of the IntID space (up to 32bit), it isn't practical
to continue using a bitmap, so let's use a different data structure
altogether.
We switch to a list, where each element represent a contiguous range
of LPIs. On allocation, we simply grab the first group big enough to
satisfy the allocation, and substract what we need from it. If the
group becomes empty, we just remove it. On freeing interrupts, we
insert a new group of interrupt in the list, sort it and fuse the
adjacent groups.
This makes freeing interrupt much more expensive than allocating
them (an unusual behaviour), but that's fine as long as we consider
that freeing interrupts is an extremely rare event.
We still allocate interrupts in blocks of 32 for the time being,
but subsequent patches will relax this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enabling LPIs was made a lot stricter recently, by checking that they are
disabled before enabling them. By doing so, the CPU hotplug case was missed
altogether, which leaves LPIs enabled on hotplug off (expecting the CPU to
eventually come back), and won't write a different value anyway on hotplug
on.
So skip that check if that particular case is detected
Fixes: 6eb486b66a ("irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling")
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lkml.kernel.org/r/20180622095254.5906-8-marc.zyngier@arm.com
Similarily to the SYNC operation, it must be verified that the VPE
targetted by a VLPI is backed by a valid collection in the GIC driver data
structures.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-7-marc.zyngier@arm.com
It is possible, under obscure circumstances, to convince the ITS driver to
emit a SYNC operation that targets a collection that is not bound to any
redistributor (and the target_address field is zero) because the
corresponding CPU has not been seen yet (the system has been booted with
max_cpus="something small").
If the ITS is using the linear CPU number as the target, this is not a big
deal, as we just end-up issuing a SYNC to CPU0. But if the ITS requires the
physical address of the redistributor (with GITS_TYPER.PTA==1), we end-up
asking the ITS to write to the physical address zero, which is not exactly
a good idea (there has been report of the ITS locking up). This should of
course never happen, but hey, this is SW...
In order to avoid the above disaster, let's track which collections have
been actually initialized, and let's not generate a SYNC if the collection
hasn't been properly bound to a redistributor. Take this opportunity to
spit our a warning, in the hope that someone may report the issue if it
arrises again.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-6-marc.zyngier@arm.com
On a NUMA system, if an ITS is local to an offline node, the ITS driver may
pick an offline CPU to bind the LPI. In this case, pick an online CPU (and
the first one will do).
But on some systems, binding an LPI to non-local node CPU may cause
deadlock (see Cavium erratum 23144). In this case, just fail the activate
and return an error code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622095254.5906-5-marc.zyngier@arm.com
These updates come with:
- OF_IOMMU support for the Rockchip iommu driver so that it can
use generic DT bindings
- Rework of locking in the AMD IOMMU interrupt remapping code to
make it work better in RT kernels
- Support for improved iotlb flushing in the AMD IOMMU driver
- Support for 52-bit physical and virtual addressing in the
ARM-SMMU
- Various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJazi2BAAoJECvwRC2XARrjYVwP/AyXK7CjRvaiHFopIUO0WpwY
V3GiKrODtSNHqPSKuFnqIssIhxZPw/SKFz6E/pe08pZ/pxHYTxeTL78Wz7D1+4Sp
n0YokSM5qLb660OTQVnyKNCku8cEMCb9hkQ/75SFgwcILQYF93cZBDIdBn93OKVO
6xAOE+tqd8Daulnk0YpdiCTFTJPzYHPl6B7scoUav26uaKxWeMJxeYe+EXC+4WQG
U1u/jDiVXyllzGgRqqfrmO4L2acmsK8HL97hD4+m1URJKDlb8ho6xwaRThFZWqXS
SbrYnvH0ruWGrLiQKmVUssw8FqbcXCzq3236g2O8jE4jqWSm70twg+q31iMjwD7v
bwsJGMkk7aLrquv9Zpaylpf8tRECk5bjhTFC2zB0pdum5XLx47j0IHKWMLPYhkCz
E0pBefvuhoSTbt/5X0urSRzH2Hk4ljEsM+QjlfH8SN3ALTljFjay607wbxC7t35M
LEL5AuNsDDBddoJIi9D13CdJEZa4lps8dbpB8m40lQVvmiLPLcKraaG0RfKQ397T
wsxhsDOQYM2FCwfUP3n8RTsMKRIp/UVkKY+2G7AsKofciSeulK6nDbrV7jFnitx4
vTxbRgpNejJpqzKZG/W9lCGWk1BhmQK/Cbu6JW5IA4+ew9omWkFp61U6rtc645Te
6cNEYBiMz/RZIiC2b18J
=kte5
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- OF_IOMMU support for the Rockchip iommu driver so that it can use
generic DT bindings
- rework of locking in the AMD IOMMU interrupt remapping code to make
it work better in RT kernels
- support for improved iotlb flushing in the AMD IOMMU driver
- support for 52-bit physical and virtual addressing in the ARM-SMMU
- various other small fixes and cleanups
* tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (53 commits)
iommu/io-pgtable-arm: Avoid warning with 32-bit phys_addr_t
iommu/rockchip: Support sharing IOMMU between masters
iommu/rockchip: Add runtime PM support
iommu/rockchip: Fix error handling in init
iommu/rockchip: Use OF_IOMMU to attach devices automatically
iommu/rockchip: Use IOMMU device for dma mapping operations
dt-bindings: iommu/rockchip: Add clock property
iommu/rockchip: Control clocks needed to access the IOMMU
iommu/rockchip: Fix TLB flush of secondary IOMMUs
iommu/rockchip: Use iopoll helpers to wait for hardware
iommu/rockchip: Fix error handling in attach
iommu/rockchip: Request irqs in rk_iommu_probe()
iommu/rockchip: Fix error handling in probe
iommu/rockchip: Prohibit unbind and remove
iommu/amd: Return proper error code in irq_remapping_alloc()
iommu/amd: Make amd_iommu_devtable_lock a spin_lock
iommu/amd: Drop the lock while allocating new irq remap table
iommu/amd: Factor out setting the remap table for a devid
iommu/amd: Use `table' instead `irt' as variable name in amd_iommu_update_ga()
iommu/amd: Remove the special case from alloc_irq_table()
...
Pull irq updates from Thomas Gleixner:
"The usual pile of boring changes:
- Consolidate tasklet functions to share code instead of duplicating
it
- The first step for making the low level entry handler management on
multi-platform kernels generic
- A new sysfs file which allows to retrieve the wakeup state of
interrupts.
- Ensure that the interrupt thread follows the effective affinity and
not the programmed affinity to avoid cross core wakeups.
- Two new interrupt controller drivers (Microsemi Ocelot and Qualcomm
PDC)
- Fix the wakeup path clock handling for Reneasas interrupt chips.
- Rework the boot time register reset for ARM GIC-V2/3
- Better suspend/resume support for ARM GIV-V3/ITS
- Add missing locking to the ARM GIC set_type() callback
- Small fixes for the irq simulator code
- SPDX identifiers for the irq core code and removal of boiler plate
- Small cleanups all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
openrisc: Set CONFIG_MULTI_IRQ_HANDLER
arm64: Set CONFIG_MULTI_IRQ_HANDLER
genirq: Make GENERIC_IRQ_MULTI_HANDLER depend on !MULTI_IRQ_HANDLER
irqchip/gic: Take lock when updating irq type
irqchip/gic: Update supports_deactivate static key to modern api
irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling
irqchip: Add a driver for the Microsemi Ocelot controller
dt-bindings: interrupt-controller: Add binding for the Microsemi Ocelot interrupt controller
irqchip/gic-v3: Probe for SCR_EL3 being clear before resetting AP0Rn
irqchip/gic-v3: Don't try to reset AP0Rn
irqchip/gic-v3: Do not check trigger configuration of partitionned LPIs
genirq: Remove license boilerplate/references
genirq: Add missing SPDX identifiers
genirq/matrix: Cleanup SPDX identifier
genirq: Cleanup top of file comments
genirq: Pass desc to __irq_free instead of irq number
irqchip/gic-v3: Loudly complain about the use of IRQ_TYPE_NONE
irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE
RISC-V: Move to the new GENERIC_IRQ_MULTI_HANDLER handler
genirq: Add CONFIG_GENERIC_IRQ_MULTI_HANDLER
...
Booting with GICR_CTLR.EnableLPI=1 is usually a bad idea, and may
result in subtle memory corruption. Detecting this is thus pretty
important.
On detecting that LPIs are still enabled, we taint the kernel (because
we're not sure of anything anymore), and try to disable LPIs. This can
fail, as implementations are allowed to implement GICR_CTLR.EnableLPI
as a one-way enable, meaning the redistributors cannot be reprogrammed
with new tables.
Should this happen, we fail probing the redistributor and warn the user
that things are pretty dire.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
[maz: reworded changelog, minor comment and message changes]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds functionality to resend the MAPC command to an ITS node on
resume. If the ITS is powered down during suspend and the collections
are not backed by memory, the ITS will lose that state. This just sets
up the known state for the collections after the ITS is restored.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some platforms power off GIC logic in suspend, so we need to
save/restore state. The distributor and redistributor registers need
to be handled in firmware code due to access permissions on those
registers, but the ITS registers can be restored in the kernel.
We limit this to systems where the ITS collections are implemented
in HW (as opposed to being backed by memory tables), as they are
the only ones that cannot be dealt with by the firmware.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
[maz: fixed changelog, dropped DT property, limited to HCC being >0]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When struct its_device instances are created, the nr_ites member
will be set to a power of 2 that equals or exceeds the requested
number of MSIs passed to the msi_prepare() callback. At the same
time, the LPI map is allocated to be some multiple of 32 in size,
where the allocated size may be less than the requested size
depending on whether a contiguous range of sufficient size is
available in the global LPI bitmap.
This may result in the situation where the nr_ites < nr_lpis, and
since nr_ites is what we program into the hardware when we map the
device, the additional LPIs will be non-functional.
For bog standard hardware, this does not really matter. However,
in cases where ITS device IDs are shared between different PCIe
devices, we may end up allocating these additional LPIs without
taking into account that they don't actually work.
So let's make nr_ites at least 32. This ensures that all allocated
LPIs are 'live', and that its_alloc_device_irq() will fail when
attempts are made to allocate MSIs beyond what was allocated in
the first place.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[maz: updated comment]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Save 26 lines worth of Sparse complaints by fixing up this minor
mishap. The pointee lies in the __iomem space; the pointer does not.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On some platforms msi parent address regions have to be excluded from
normal IOVA allocation in that they are detected and decoded in a HW
specific way by system components and so they cannot be considered normal
IOVA address space.
Add a helper function that retrieves ITS address regions - the msi
parent - through IORT device <-> ITS mappings and reserves it so that
these regions will not be translated by IOMMU and will be excluded from
IOVA allocations. The function checks for the smmu model number and
only applies the msi reservation if the platform requires it.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[For the ITS part]
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
its_vpe_irq_domain_activate should always return 0. Really. There
is not a single case why it wouldn't. So this "return true;" is
really a copy/paste issue that got revealed now that we actually
check the return value of the activate method.
Brown paper bag day.
Fixes: 2247e1bf70 ("irqchip/gic-v3-its: Limit scope of VPE mapping to be per ITS")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we require the hypervisor to update the VLPI properties
once the the VLPI mapping has been established. While this
makes it easy for the ITS driver, it creates a window where
an incoming interrupt can be delivered with an unknown set
of properties. Not very nice.
Instead, let's add a "properties" field to the mapping structure,
and use that to configure the VLPI before it actually gets mapped.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When setting the affinity of a VPE (either because we map or move
it), make sure the effective affinity is correctly reported back
to the core kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Sending VINVALL to all ITSs is completely pointless, as all
we're trying to achieve is to tell the redistributor that
the property table for this VPE should be invalidated.
Let's issue the command on the first valid ITS and be done with it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we map all VPEs on all ITSs. While this is not wrong,
this is quite a big hammer, as moving a VPE around requires
all ITSs to be synchronized. Needles to say, this is an
expensive proposition.
Instead, let's switch to a mode where we issue VMAPP commands
only on ITSs that are actually involved in reporting interrupts
to the given VM.
For that purpose, we refcount the number of interrupts are are
mapped for this VM on each ITS, performing the map/unmap
operations as required. It then allows us to use this refcount
to only issue VMOVP to the ITSs that need to know about this
VM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vmapp operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vinvall operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to make use of the maximum number of ITSs in
a GICv4 system, let's make this value global (and rename it to
GICv4_ITS_LIST_MAX).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At boot time, we enumerate all the GICv4-capable ITSs, and build
a mask of the available ITSs. Take this opportunity to store
the ITS number in the its_node structure so that we can use it
at a later time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to be able to issue command variants depending on
how broken an ITS is, let's pass the its pointer to all
command building primitives.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the ITS stops processing commands, we're pretty much toasted
as we cannot update the configuration anymore (and we're not
even sure that the ITS still translates interrups).
If that happens, let's dump some basic information about the
state of affairs before moving on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As it turns out, the IIDR is not sufficient to distinguish between GICv3
implementations when it comes to enabling quirks. So update the prototype
of the init() hook to return a bool, and interpret a 'false' return value
as no match, in which case the 'enabling workaround' log message should
not be printed.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Before adding another SoC whose device ID space deviates from the
value presented in the GIC ID registers, let's slightly refactor
the code so that the ID registers are probed before that quirks
handling executes. This allows us to move the device ID override
into the quirk handler itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current ITS driver works fine as long as normal memory and GICR
regions are located within the lower 48bit (>=0 && <2^48) physical
address space. Some of the registers GICR_PEND/PROP, GICR_VPEND/VPROP
and GITS_CBASER are handled properly but not all when configuring
the hardware with 52bit physical address.
This patch does the following changes to support 52bit PA.
-Handle 52bit PA in GITS_BASERn.
-Fix ITT_addr width to 52bits, bits[51:8].
-Fix RDbase width to 52bits, bits[51:16].
-Fix VPT_addr width to 52bits, bits[51:16].
Definition of the GITS_BASERn register when ITS PageSize is 64KB:
-Bits[47:16] of the register provide bits[47:16] of the table PA.
-Bits[15:12] of the register provide bits[51:48] of the table PA.
-Bits[15:00] of the base physical address are 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VCPU table consists of vPE entries, and its size provides the number
of VPEs supported by GICv4 hardware. Unfortunately the maximum size of
the VPE table is not discoverable like Device table. All VLPI commands
limits the number of bits to 16 to hold VPEID, which is index into VCPU
table. Don't apply DEVID bits for VCPU table instead assume maximum bits
to 16.
ITS log messages on QDF2400 without fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
Virtual CPUs Table too large, reduce ids 32->26
Virtual CPUs too large, reduce ITS pages 8192->256
allocated 2097152 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
ITS log messages on QDF2400 with fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
allocated 65536 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The driver probe path hits 'BUG_ON(entries != vpe_proxy.dev->nr_ites)'
on systems where it has VLPI capability, doesn't support direct LPI
feature and boot with a single CPU.
Relax the BUG_ON() condition to fix the issue.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
-----BEGIN PGP SIGNATURE-----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=3ZS3
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for 4.14 from Marc Zyngier:
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
