Since sub-testing can now be detected by indentation level, this removes
KSFT_TAP_LEVEL so that subtests report their TAP header for later parsing.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This changes the selftest output so that each test's output is prefixed
with "# " as a TAP "diagnostic line".
This creates a bit of a kernel-specific TAP dialect where the diagnostics
precede the results. The TAP spec isn't entirely clear about this, though,
so I think it's the correct solution so as to keep interactive runs making
sense. If the output _followed_ the result line in the spec-suggested
YAML form, each test would dump all of its output at once instead of as
it went, making debugging harder.
This does, however, solve the recursive TAP output problem, as sub-tests
will simply be prefixed by "# ". Parsing sub-tests becomes a simple
problem of just removing the first two characters of a given top-level
test's diagnostic output, and parsing the results.
Note that the shell construct needed to both get an exit code from
the first command in a pipe and still filter the pipe (to add the "# "
prefix) uses a POSIX solution rather than the bash "pipefail" option
which is not supported by dash.
Since some test environments may have a very minimal set of utilities
available, the new prefixing code will fall back to doing line-at-a-time
prefixing if perl and/or stdbuf are not available.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
If a test was missing (e.g. wrong architecture, etc), the test runner
would incorrectly claim the test was non-executable. This adds an
existence check to report correctly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The TAP version 13 spec requires a "plan" line, which has been missing.
Since we always know how many tests we're going to run, emit the count on
the plan line. This also fixes the result lines to remove the "1.." prefix
which is against spec, and to mark skips with the correct "# SKIP" suffix.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This moves the logic for running multiple tests into a single "run_many"
function of runner.sh. Both "run_tests" and "emit_tests" are modified to
use it. Summary handling is now controlled by the "per_test_logging"
shell flag.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This reuses the new runner.sh for the emit targets instead of manually
running each test via run_kselftest.sh.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
In order to improve the reusability of the kselftest test running logic,
this extracts the single-test logic from lib.mk into kselftest/runner.sh
which lib.mk can call directly. No changes in output.
As part of the change, this moves the "summary" Makefile logic around
to set a new "logfile" output. This will be used again in the future
"emit_tests" target as well.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
So far, all BPF tc tunnel testcases encapsulate in the same network
protocol. Add an encap testcase that requires updating skb->protocol.
The 6in4 tunnel encapsulates an IPv6 packet inside an IPv4 tunnel.
Verify that bpf_skb_net_grow correctly updates skb->protocol to
select the right protocol handler in __netif_receive_skb_core.
The BPF program should also manually update the link layer header to
encode the right network protocol.
Changes v1->v2
- improve documentation of non-obvious logic
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Alan Maguire <alan.maguire@oracle.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Now that we use skb-less flow dissector let's return true nhoff and
thoff. We used to adjust them by ETH_HLEN because that's how it was
done in the skb case. For VLAN tests that looks confusing: nhoff is
pointing to vlan parts :-\
Warning, this is an API change for BPF_PROG_TEST_RUN! Feel free to drop
if you think that it's too late at this point to fix it.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Right now we incorrectly return 'ret' which is always zero at that
point.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Export last_dissection map from flow dissector and use a known place in
tun driver to trigger BPF flow dissection.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When flow dissector is called without skb, we want to make sure
bpf_skb_load_bytes invocations return error. Add small test which tries
to read single byte from a packet.
bpf_skb_load_bytes should always fail under BPF_PROG_TEST_RUN because
it was converted to the skb-less mode.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-04-22
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) allow stack/queue helpers from more bpf program types, from Alban.
2) allow parallel verification of root bpf programs, from Alexei.
3) introduce bpf sysctl hook for trusted root cases, from Andrey.
4) recognize var/datasec in btf deduplication, from Andrii.
5) cpumap performance optimizations, from Jesper.
6) verifier prep for alu32 optimization, from Jiong.
7) libbpf xsk cleanup, from Magnus.
8) other various fixes and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Add a selftest for icmp packet too big errors with conntrack, from
Florian Westphal.
2) Validate inner header in ICMP error message does not lie to us
in conntrack, also from Florian.
3) Initialize ct->timeout to calm down KASAN, from Alexander Potapenko.
4) Skip ICMP error messages from tunnels in IPVS, from Julian Anastasov.
5) Use a hash to expose conntrack and expectation ID, from Florian Westphal.
6) Prevent shift wrap in nft_chain_parse_hook(), from Dan Carpenter.
7) Fix broken ICMP ID randomization with NAT, also from Florian.
8) Remove WARN_ON in ebtables compat that is reached via syzkaller,
from Florian Westphal.
9) Fix broken timestamps since fb420d5d91 ("tcp/fq: move back to
CLOCK_MONOTONIC"), from Florian.
10) Fix logging of invalid packets in conntrack, from Andrei Vagin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Build and run gpio when output directory is the src dir. gpio has
dependency on tools/gpio and builds tools/gpio objects in the src
directory in all cases making the src repo dirty even when object
relocation is specified.
This fixes the following commands from generating gpio objects in
the source repository:
make O=dir kselftest
export KBUILD_OUTPUT=dir; make kselftest
make O=dir -C tools/testing/selftests
expoert KBUILD_OUTPUT=dir; make -C tools/testing/selftests
The following commands still build gpio objects in the source repo
(gpio Makefile needs to fixed):
make O=dir kselftest TARGETS="gpio"
export KBUILD_OUTPUT=dir; make kselftest TARGETS="gpio"
make O=dir -C tools/testing/selftests TARGETS="gpio"
expoert KBUILD_OUTPUT=dir; make -C tools/testing/selftests TARGETS="gpio"
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add nfit_test 'watermarks' for the dax_pmem, dax_pmem_core, and
dax_pmem_compat modules. This causes the nfit_test module to fail
loading in case any of these modules are also not overridden with the
ldconfig wrapped modules. Without this, nfit_test would sometimes fail
creation of device-dax namespaces on the nfit_test_bus with an unhelpful
error log such as:
dax_pmem dax5.0: could not reserve metadata
dax_pmem: probe of dax5.0 failed with error -16
Which was caused due to the unwrapped version of
devm_request_mem_region() being called.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAly8rGYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGmZMH/1IRB0E1Qmzz8yzw
wj79UuRGYPqxDDSWW+wNc8sU4Ic7iYirn9APHAztCdQqsjmzU/OVLfSa3JhdBe5w
THo7pbGKBqEDcWnKfNk/21jXFNLZ1vr9BoQv2DGU2MMhHAyo/NZbalo2YVtpQPmM
OCRth5n+LzvH7rGrX7RYgWu24G9l3NMfgtaDAXBNXesCGFAjVRrdkU5CBAaabvtU
4GWh/nnutndOOLdByL3x+VZ3H3fIBnbNjcIGCglvvqzk7h3hrfGEl4UCULldTxcM
IFsfMUhSw1ENy7F6DHGbKIG90cdCJcrQ8J/ziEzjj/KLGALluutfFhVvr6YCM2J6
2RgU8CY=
=CfY1
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rc6' into for-5.2/block
Pull in v5.1-rc6 to resolve two conflicts. One is in BFQ, in just a
comment, and is trivial. The other one is a conflict due to a later fix
in the bio multi-page work, and needs a bit more care.
* tag 'v5.1-rc6': (770 commits)
Linux 5.1-rc6
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new test for Media Device Allocator API.
Media Device Allocator API to allows multiple drivers share a media device.
This API solves a very common use-case for media devices where one physical
device (an USB stick) provides both audio and video. When such media device
exposes a standard USB Audio class, a proprietary Video class, two or more
independent drivers will share a single physical USB bridge. In such cases,
it is necessary to coordinate access to the shared resource.
Using this API, drivers can allocate a media device with the shared struct
device as the key. Once the media device is allocated by a driver, other
drivers can get a reference to it. The media device is released when all
the references are released.
This test does a series of unbind/bind tests to make sure media device
is released correctly when it is no longer is use and when the last
driver releases the reference.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The run_afpackettests will be marked as passed regardless the return
value of those sub-tests in the script:
--------------------
running psock_tpacket test
--------------------
[FAIL]
selftests: run_afpackettests [PASS]
Fix this by changing the return value for each tests.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the various compiler warnings when building the msgque
selftest. The primary change is using sys/msg.h instead of linux/msg.h
directly to gain the API declarations.
Fixes: 3a665531a3 ("selftests: IPC message queue copy feature test")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Test files created by test_create() and test_create_empty() tests will
stay in the $efivarfs_mount directory until the system was rebooted.
When the tester tries to run this efivarfs test again on the same
system, the immutable characteristics in that directory will cause some
"Operation not permitted" noises, and a false-positve test result as the
file was created in previous run.
--------------------
running test_create
--------------------
./efivarfs.sh: line 59: /sys/firmware/efi/efivars/test_create-210be57c-9849-4fc7-a635-e6382d1aec27: Operation not permitted
[PASS]
--------------------
running test_create_empty
--------------------
./efivarfs.sh: line 78: /sys/firmware/efi/efivars/test_create_empty-210be57c-9849-4fc7-a635-e6382d1aec27: Operation not permitted
[PASS]
--------------------
Create a file_cleanup() to remove those test files in the end of each
test to solve this issue.
For the test_create_read, we can move the clean up task to the end of
the test to ensure the system is clean.
Also, use this function to replace the existing file removal code.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
"make kselftest" fails with "Circular Makefile.o <- prepare dependency
dropped." error, when lib.mk invokes "make headers_install".
Make level 0: Main make calls selftests run_tests target
...
Make level n: selftests lib.mk invokes main make's headers_install
The secondary level make inherits builtin-rules which will use the rule
to generate Makefile.o and runs into "Circular Makefile.o <- prepare
dependency dropped." error, and kselftest compile fails.
Invoke headers_install target with --no-builtin-rules to avoid circular
error.
In addition, lib.mk installs headers in the default HDR_PATH, even when
build relocation is requested with O= or export KBUILD_OUTPUT. Fix the
problem by passing in INSTALL_HDR_PATH. The headers are installed under
the specified output "dir/usr".
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The run_netsocktests will be marked as passed regardless the actual test
result from the ./socket:
selftests: net: run_netsocktests
========================================
--------------------
running socket test
--------------------
[FAIL]
ok 1..6 selftests: net: run_netsocktests [PASS]
This is because the test script itself has been successfully executed.
Fix this by exit 1 when the test failed.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements 9 tests for the freezer controller for
cgroup v2:
1) a simple test, which aims to freeze and unfreeze a cgroup with 100
processes
2) a more complicated tree test, which creates a hierarchy of cgroups,
puts some processes in some cgroups, and tries to freeze and unfreeze
different parts of the subtree
3) a forkbomb test: the test aims to freeze a forkbomb running in a
cgroup, kill all tasks in the cgroup and remove the cgroup without
the unfreezing.
4) rmdir test: the test creates two nested cgroups, freezes the parent
one, checks that the child can be successfully removed, and a new
child can be created
5) migration tests: the test checks migration of a task between
frozen cgroups: from a frozen to a running, from a running to a
frozen, and from a frozen to a frozen.
6) ptrace test: the test checks that it's possible to attach to
a process in a frozen cgroup, get some information and detach, and
the cgroup will remain frozen.
7) stopped test: the test checks that it's possible to freeze a cgroup
with a stopped task
8) ptraced test: the test checks that it's possible to freeze a cgroup
with a ptraced task
9) vfork test: the test checks that it's possible to freeze a cgroup
with a parent process waiting for the child process in vfork()
Expected output:
$ ./test_freezer
ok 1 test_cgfreezer_simple
ok 2 test_cgfreezer_tree
ok 3 test_cgfreezer_forkbomb
ok 4 test_cgrreezer_rmdir
ok 5 test_cgfreezer_migrate
ok 6 test_cgfreezer_ptrace
ok 7 test_cgfreezer_stopped
ok 8 test_cgfreezer_ptraced
ok 9 test_cgfreezer_vfork
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: kernel-team@fb.com
Cc: linux-kselftest@vger.kernel.org
If the cgroup destruction races with an exit() of a belonging
process(es), cg_kill_all() may fail. It's not a good reason to make
cg_destroy() fail and leave the cgroup in place, potentially causing
next test runs to fail.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: kernel-team@fb.com
Cc: linux-kselftest@vger.kernel.org
map_fds[16] is the last one index-ed by fixup_map_array_small.
Hence, the MAX_NR_MAPS should be 17 instead.
Fixes: fb2abb73e5 ("bpf, selftest: test {rd, wr}only flags and direct value access")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
I meet below compile errors:
"
In file included from test_tcpnotify_kern.c:12:
/usr/include/netinet/in.h:101:5: error: expected identifier
IPPROTO_HOPOPTS = 0, /* IPv6 Hop-by-Hop options. */
^
/usr/include/linux/in6.h:131:26: note: expanded from macro 'IPPROTO_HOPOPTS'
^
In file included from test_tcpnotify_kern.c:12:
/usr/include/netinet/in.h:103:5: error: expected identifier
IPPROTO_ROUTING = 43, /* IPv6 routing header. */
^
/usr/include/linux/in6.h:132:26: note: expanded from macro 'IPPROTO_ROUTING'
^
In file included from test_tcpnotify_kern.c:12:
/usr/include/netinet/in.h:105:5: error: expected identifier
IPPROTO_FRAGMENT = 44, /* IPv6 fragmentation header. */
^
/usr/include/linux/in6.h:133:26: note: expanded from macro 'IPPROTO_FRAGMENT'
"
The same compile errors are reported for test_tcpbpf_kern.c too.
My environment:
lsb_release -a:
No LSB modules are available.
Distributor ID: Ubuntu
Description: Ubuntu 16.04.6 LTS
Release: 16.04
Codename: xenial
dpkg -l | grep libc-dev:
ii libc-dev-bin 2.23-0ubuntu11 amd64 GNU C Library: Development binaries
ii linux-libc-dev:amd64 4.4.0-145.171 amd64 Linux Kernel Headers for development.
The reason is linux/in6.h and netinet/in.h aren't synchronous about how to
handle the same definitions, IPPROTO_HOPOPTS, etc.
This patch fixes the compile errors by moving <netinet/in.h> to before the
<linux/*.h>.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Unexpected power cycle occurs while the installation of the
kernel.
ssh root@Test sync ... [0 seconds] SUCCESS
ssh root@Test reboot ... [1 second] FAILED!
virsh destroy Test; sleep 5; virsh start Test ... [6 seconds] SUCCESS
That is because REBOOT, the default is "ssh $SSH_USER@$MACHINE
reboot", exits as 255 even if the reboot is successfully done,
like as:
]# ssh root@Test reboot
Connection to Test closed by remote host.
]# echo $?
255
]#
To avoid the unexpected power cycle, introduce a new parameter,
REBOOT_RETURN_CODE to judge whether REBOOT is successfully done
or not.
Link: http://lkml.kernel.org/r/20190418135943.12640-1-msys.mizuma@gmail.com
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull RCU and LKMM commits from Paul E. McKenney:
- An LKMM commit adding support for synchronize_srcu_expedited()
- A couple of straggling RCU flavor consolidation updates
- Documentation updates.
- Miscellaneous fixes
- SRCU updates
- RCU CPU stall-warning updates
- Torture-test updates
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I hit the following compilation error with gcc 4.8.5.
prog_tests/flow_dissector.c: In function ‘test_flow_dissector’:
prog_tests/flow_dissector.c:155:2: error: ‘for’ loop initial declarations are only allowed in C99 mode
for (int i = 0; i < ARRAY_SIZE(tests); i++) {
^
prog_tests/flow_dissector.c:155:2: note: use option -std=c99 or -std=gnu99 to compile your code
Let us fix the issue by avoiding this particular c99 feature.
Fixes: a5cb33464e ("selftests/bpf: make flow dissector tests more extensible")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
ktest fails if meta characters are in GRUB_MENU, for example
GRUB_MENU = 'Fedora (test)'
The failure happens because the meta characters are not escaped,
so the menu doesn't match in any entries in GRUB_FILE.
Use quotemeta() to escape the meta characters.
Link: http://lkml.kernel.org/r/20190417235823.18176-1-msys.mizuma@gmail.com
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If a test has an error, display not only the what type of test failed, but
if the test was giving a name, display that too, as well as the current
iteration of the tests. Each test has an iteration number associated to it.
For error messages display that iteration number along with the test type
and test name. This includes the message that gets sent via email.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The get_secureboot_mode() function unnecessarily requires both
CONFIG_EFIVAR_FS and CONFIG_EFI_VARS to be enabled to determine if the
system is booted in secure boot mode. On some systems the old EFI
variable support is not enabled or, possibly, even implemented.
This patch first checks the efivars filesystem for the SecureBoot and
SetupMode flags, but falls back to using the old EFI variable support.
The "secure_boot_file" and "setup_mode_file" couldn't be quoted due to
globbing. This patch also removes the globbing.
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Verify IMA is enabled before failing tests or emitting irrelevant
messages.
Suggested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Skip the kexec_load and kexec_file_load tests, if they aren't configured
in the kernel. This change adds a new requirement that ikconfig is
configured in the kexec_load test.
Suggested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
so the file can be used as kernel config snippet.
Signed-off-by: Petr Vorel <pvorel@suse.cz>
[zohar@linux.ibm.com: remove CONFIG_KEXEC_VERIFY_SIG from config]
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The kernel can be configured to verify PE signed kernel images, IMA
kernel image signatures, both types of signatures, or none. This test
verifies only properly signed kernel images are loaded into memory,
based on the kernel configuration and runtime policies.
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Many tests require root privileges. Define a common function.
Suggested-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Define, update and move get_secureboot_mode() to a common file for use
by other tests.
Updated to check both the efivar SecureBoot-$(UUID) and
SetupMode-$(UUID), based on Dave Young's review.
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Remove the few bashisms and use the complete option name for clarity.
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
As requested move the existing kexec_load selftest and subsequent kexec
tests to the selftests/kexec directory.
Suggested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Pull networking fixes from David Miller:
1) Handle init flow failures properly in iwlwifi driver, from Shahar S
Matityahu.
2) mac80211 TXQs need to be unscheduled on powersave start, from Felix
Fietkau.
3) SKB memory accounting fix in A-MDSU aggregation, from Felix Fietkau.
4) Increase RCU lock hold time in mlx5 FPGA code, from Saeed Mahameed.
5) Avoid checksum complete with XDP in mlx5, also from Saeed.
6) Fix netdev feature clobbering in ibmvnic driver, from Thomas Falcon.
7) Partial sent TLS record leak fix from Jakub Kicinski.
8) Reject zero size iova range in vhost, from Jason Wang.
9) Allow pending work to complete before clcsock release from Karsten
Graul.
10) Fix XDP handling max MTU in thunderx, from Matteo Croce.
11) A lot of protocols look at the sa_family field of a sockaddr before
validating it's length is large enough, from Tetsuo Handa.
12) Don't write to free'd pointer in qede ptp error path, from Colin Ian
King.
13) Have to recompile IP options in ipv4_link_failure because it can be
invoked from ARP, from Stephen Suryaputra.
14) Doorbell handling fixes in qed from Denis Bolotin.
15) Revert net-sysfs kobject register leak fix, it causes new problems.
From Wang Hai.
16) Spectre v1 fix in ATM code, from Gustavo A. R. Silva.
17) Fix put of BROPT_VLAN_STATS_PER_PORT in bridging code, from Nikolay
Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (111 commits)
socket: fix compat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW
tcp: tcp_grow_window() needs to respect tcp_space()
ocelot: Clean up stats update deferred work
ocelot: Don't sleep in atomic context (irqs_disabled())
net: bridge: fix netlink export of vlan_stats_per_port option
qed: fix spelling mistake "faspath" -> "fastpath"
tipc: set sysctl_tipc_rmem and named_timeout right range
tipc: fix link established but not in session
net: Fix missing meta data in skb with vlan packet
net: atm: Fix potential Spectre v1 vulnerabilities
net/core: work around section mismatch warning for ptp_classifier
net: bridge: fix per-port af_packet sockets
bnx2x: fix spelling mistake "dicline" -> "decline"
route: Avoid crash from dereferencing NULL rt->from
MAINTAINERS: normalize Woojung Huh's email address
bonding: fix event handling for stacked bonds
Revert "net-sysfs: Fix memory leak in netdev_register_kobject"
rtnetlink: fix rtnl_valid_stats_req() nlmsg_len check
qed: Fix the DORQ's attentions handling
qed: Fix missing DORQ attentions
...
This patch adds tests validating that VRF and BPF-LWT
encap work together well, as requested by David Ahern.
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In order to keep tests from hanging forever, this adds an alarm signal
to each test run. This assumes an individual test doesn't take longer
than 30 seconds.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
When running without USERNS or PIDNS the seccomp test would hang since
it was waiting forever for the child to trigger the user notification
since it seems the glibc() abort handler makes a call to getpid(),
which would trap again. This changes the getpid filter to getppid, and
makes sure ASSERTs execute to stop from spawning the listener.
Reported-by: Shuah Khan <shuah@kernel.org>
Fixes: 6a21cc50f0 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org # > 5.0
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
* Fixes for nested VMX with ept=0
* Fixes for AMD (APIC virtualization, NMI injection)
* Fixes for Hyper-V under KVM and KVM under Hyper-V
* Fixes for 32-bit SMM and tests for SMM virtualization
* More array_index_nospec peppering
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJctdrUAAoJEL/70l94x66Deq8H/0OEIBBuDt53nPEHXufNSV1S
uzIVvwJoL6786URWZfWZ99Z/NTTA1rn9Vr/leLPkSidpDpw7IuK28KZtEMP2rdRE
Sb8eN2g4SoQ51ZDSIMUzjcx9VGNqkH8CWXc2yhDtTUSD21S3S1kidZ0O0YbmetkJ
OwF1EDx4m7JO6EUHaJhIfdTUb9ItRC1Vfo7hpOuRVxPx2USv5+CLbexpteKogMcI
5WDaXFIRwUWW6Z8Bwyi7yA9gELKcXTTXlz9T/A7iKeqxRMLBazVKnH8h7Lfd0M0A
wR4AI+tE30MuHT7WLh1VOAKZk6TDabq9FJrva3JlDq+T+WOjgUzYALLKEd4Vv4o=
=zsT5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"5.1 keeps its reputation as a big bugfix release for KVM x86.
- Fix for a memory leak introduced during the merge window
- Fixes for nested VMX with ept=0
- Fixes for AMD (APIC virtualization, NMI injection)
- Fixes for Hyper-V under KVM and KVM under Hyper-V
- Fixes for 32-bit SMM and tests for SMM virtualization
- More array_index_nospec peppering"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: x86: avoid misreporting level-triggered irqs as edge-triggered in tracing
KVM: fix spectrev1 gadgets
KVM: x86: fix warning Using plain integer as NULL pointer
selftests: kvm: add a selftest for SMM
selftests: kvm: fix for compilers that do not support -no-pie
selftests: kvm/evmcs_test: complete I/O before migrating guest state
KVM: x86: Always use 32-bit SMRAM save state for 32-bit kernels
KVM: x86: Don't clear EFER during SMM transitions for 32-bit vCPU
KVM: x86: clear SMM flags before loading state while leaving SMM
KVM: x86: Open code kvm_set_hflags
KVM: x86: Load SMRAM in a single shot when leaving SMM
KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU
KVM: x86: Raise #GP when guest vCPU do not support PMU
x86/kvm: move kvm_load/put_guest_xcr0 into atomic context
KVM: x86: svm: make sure NMI is injected after nmi_singlestep
svm/avic: Fix invalidate logical APIC id entry
Revert "svm: Fix AVIC incomplete IPI emulation"
kvm: mmu: Fix overflow on kvm mmu page limit calculation
KVM: nVMX: always use early vmcs check when EPT is disabled
KVM: nVMX: allow tests to use bad virtual-APIC page address
...
Add a simple test for SMM, based on VMX. The test implements its own
sync between the guest and the host as using our ucall library seems to
be too cumbersome: SMI handler is happening in real-address mode.
This patch also fixes KVM_SET_NESTED_STATE to happen after
KVM_SET_VCPU_EVENTS, in fact it places it last. This is because
KVM needs to know whether the processor is in SMM or not.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-no-pie was added to GCC at the same time as their configuration option
--enable-default-pie. Compilers that were built before do not have
-no-pie, but they also do not need it. Detect the option at build
time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Starting state migration after an IO exit without first completing IO
may result in test failures. We already have two tests that need this
(this patch in fact fixes evmcs_test, similar to what was fixed for
state_test in commit 0f73bbc851, "KVM: selftests: complete IO before
migrating guest state", 2019-03-13) and a third is coming. So, move the
code to vcpu_save_state, and while at it do not access register state
until after I/O is complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rewrite selftest to iterate over an array with input packet and
expected flow_keys. This should make it easier to extend this test
with additional cases without too much boilerplate.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add two tests to check that sequence of 1024 jumps is verifiable.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It was removed in commit 166b5a7f2c ("selftests_bpf: extend
test_tc_tunnel for UDP encap") without any explanation.
Otherwise I see:
progs/test_tc_tunnel.c:160:17: warning: taking address of packed member 'ip' of class or structure
'v4hdr' may result in an unaligned pointer value [-Waddress-of-packed-member]
set_ipv4_csum(&h_outer.ip);
^~~~~~~~~~
1 warning generated.
Cc: Alan Maguire <alan.maguire@oracle.com>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Fixes: 166b5a7f2c ("selftests_bpf: extend test_tc_tunnel for UDP encap")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add test case verifying that dedup happens (INTs are deduped in this
case) and VAR/DATASEC types are not deduped, but have their referenced
type IDs adjusted correctly.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Yonghong Song <yhs@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
- Compatibility fix for nvdimm-security implementations with a default
zero-key.
- Miscellaneous small fixes for out-of-bound accesses, cleanup after
initialization failures, and missing debug messages.
-----BEGIN PGP SIGNATURE-----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=zISv
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-fixes-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"I debated holding this back for the v5.2 merge window due to the size
of the "zero-key" changes, but affected users would benefit from
having the fixes sooner. It did not make sense to change the zero-key
semantic in isolation for the "secure-erase" command, but instead
include it for all security commands.
The short background on the need for these changes is that some NVDIMM
platforms enable security with a default zero-key rather than let the
OS specify the initial key. This makes the security enabling that
landed in v5.0 unusable for some users.
Summary:
- Compatibility fix for nvdimm-security implementations with a
default zero-key.
- Miscellaneous small fixes for out-of-bound accesses, cleanup after
initialization failures, and missing debug messages"
* tag 'libnvdimm-fixes-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: Retain security state after overwrite
libnvdimm/pmem: fix a possible OOB access when read and write pmem
libnvdimm/security, acpi/nfit: unify zero-key for all security commands
libnvdimm/security: provide fix for secure-erase to use zero-key
libnvdimm/btt: Fix a kmemdup failure check
libnvdimm/namespace: Fix a potential NULL pointer dereference
acpi/nfit: Always dump _DSM output payload
Test that neighbour entries are marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove the broute pseudo hook, implement this from the bridge
prerouting hook instead. Now broute becomes real table in ebtables,
from Florian Westphal. This also includes a size reduction patch for the
bridge control buffer area via squashing boolean into bitfields and
a selftest.
2) Add OS passive fingerprint version matching, from Fernando Fernandez.
3) Support for gue encapsulation for IPVS, from Jacky Hu.
4) Add support for NAT to the inet family, from Florian Westphal.
This includes support for masquerade, redirect and nat extensions.
5) Skip interface lookup in flowtable, use device in the dst object.
6) Add jiffies64_to_msecs() and use it, from Li RongQing.
7) Remove unused parameter in nf_tables_set_desc_parse(), from Colin Ian King.
8) Statify several functions, patches from YueHaibing and Florian Westphal.
9) Add an optimized version of nf_inet_addr_cmp(), from Li RongQing.
10) Merge route extension to core, also from Florian.
11) Use IS_ENABLED(CONFIG_NF_NAT) instead of NF_NAT_NEEDED, from Florian.
12) Merge ip/ip6 masquerade extensions, from Florian. This includes
netdevice notifier unification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions.sh to TEST_PROGS_EXTENDED so that it is installed along
with the rest of the selftests and they can be run.
Originally-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Sven Auhagen reported that a 2nd ping request will fail if 'fully-random'
mode is used.
Reason is that if no proto information is given, min/max are both 0,
so we set the icmp id to 0 instead of chosing a random value between
0 and 65535.
Update test case as well to catch this, without fix this yields:
[..]
ERROR: cannot ping ns1 from ns2 with ip masquerade fully-random (attempt 2)
ERROR: cannot ping ns1 from ns2 with ipv6 masquerade fully-random (attempt 2)
... becaus 2nd ping clashes with existing 'id 0' icmp conntrack and gets
dropped.
Fixes: 203f2e7820 ("netfilter: nat: remove l4proto->unique_tuple")
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When an icmp error such as pkttoobig is received, conntrack checks
if the "inner" header (header of packet that did not fit link mtu)
is matches an existing connection, and, if so, sets that packet as
being related to the conntrack entry it found.
It was recently reported that this "related" setting also works
if the inner header is from another, different connection (i.e.,
artificial/forged icmp error).
Add a test, followup patch will add additional "inner dst matches
outer dst in reverse direction" check before setting related state.
Link: https://www.synacktiv.com/posts/systems/icmp-reachable.html
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some netdevsim bpf debugfs files are per-sdev, yet they are defined per
netdevsim instance. Move them under sdev directory.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add C based test for a few bpf_sysctl_* helpers and bpf_strtoul.
Make sure that sysctl can be identified by name and that multiple
integers can be parsed from sysctl value with bpf_strtoul.
net/ipv4/tcp_mem is chosen as a testing sysctl, it contains 3 unsigned
longs, they all are parsed and compared (val[0] < val[1] < val[2]).
Example of output:
# ./test_sysctl
...
Test case: C prog: deny all writes .. [PASS]
Test case: C prog: deny access by name .. [PASS]
Test case: C prog: read tcp_mem .. [PASS]
Summary: 39 PASSED, 0 FAILED
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Test that bpf_strtol and bpf_strtoul helpers can be used to convert
provided buffer to long or unsigned long correspondingly and return both
correct result and number of consumed bytes, or proper errno.
Example of output:
# ./test_sysctl
..
Test case: bpf_strtoul one number string .. [PASS]
Test case: bpf_strtoul multi number string .. [PASS]
Test case: bpf_strtoul buf_len = 0, reject .. [PASS]
Test case: bpf_strtoul supported base, ok .. [PASS]
Test case: bpf_strtoul unsupported base, EINVAL .. [PASS]
Test case: bpf_strtoul buf with spaces only, EINVAL .. [PASS]
Test case: bpf_strtoul negative number, EINVAL .. [PASS]
Test case: bpf_strtol negative number, ok .. [PASS]
Test case: bpf_strtol hex number, ok .. [PASS]
Test case: bpf_strtol max long .. [PASS]
Test case: bpf_strtol overflow, ERANGE .. [PASS]
Summary: 36 PASSED, 0 FAILED
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Test that verifier handles new argument types properly, including
uninitialized or partially initialized value, misaligned stack access,
etc.
Example of output:
#456/p ARG_PTR_TO_LONG uninitialized OK
#457/p ARG_PTR_TO_LONG half-uninitialized OK
#458/p ARG_PTR_TO_LONG misaligned OK
#459/p ARG_PTR_TO_LONG size < sizeof(long) OK
#460/p ARG_PTR_TO_LONG initialized OK
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Test access to file_pos field of bpf_sysctl context, both read (incl.
narrow read) and write.
# ./test_sysctl
...
Test case: ctx:file_pos sysctl:read read ok .. [PASS]
Test case: ctx:file_pos sysctl:read read ok narrow .. [PASS]
Test case: ctx:file_pos sysctl:read write ok .. [PASS]
...
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Test that new value provided by user space on sysctl write can be read
by bpf_sysctl_get_new_value and overridden by bpf_sysctl_set_new_value.
# ./test_sysctl
...
Test case: sysctl_get_new_value sysctl:read EINVAL .. [PASS]
Test case: sysctl_get_new_value sysctl:write ok .. [PASS]
Test case: sysctl_get_new_value sysctl:write ok long .. [PASS]
Test case: sysctl_get_new_value sysctl:write E2BIG .. [PASS]
Test case: sysctl_set_new_value sysctl:read EINVAL .. [PASS]
Test case: sysctl_set_new_value sysctl:write ok .. [PASS]
Summary: 22 PASSED, 0 FAILED
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Test sysctl_get_current_value on sysctl read and write, buffers with
enough space and too small buffers to get E2BIG and truncated result,
etc.
# ./test_sysctl
...
Test case: sysctl_get_current_value sysctl:read ok, gt .. [PASS]
Test case: sysctl_get_current_value sysctl:read ok, eq .. [PASS]
Test case: sysctl_get_current_value sysctl:read E2BIG truncated .. [PASS]
Test case: sysctl_get_current_value sysctl:read EINVAL .. [PASS]
Test case: sysctl_get_current_value sysctl:write ok .. [PASS]
Summary: 16 PASSED, 0 FAILED
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Test w/ and w/o BPF_F_SYSCTL_BASE_NAME, buffers with enough space and
too small buffers to get E2BIG and truncated result, etc.
# ./test_sysctl
...
Test case: sysctl_get_name sysctl_value:base ok .. [PASS]
Test case: sysctl_get_name sysctl_value:base E2BIG truncated .. [PASS]
Test case: sysctl_get_name sysctl:full ok .. [PASS]
Test case: sysctl_get_name sysctl:full E2BIG truncated .. [PASS]
Test case: sysctl_get_name sysctl:full E2BIG truncated small .. [PASS]
Summary: 11 PASSED, 0 FAILED
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add unit test for BPF_PROG_TYPE_CGROUP_SYSCTL program type.
Test that program can allow/deny access.
Test both valid and invalid accesses to ctx->write.
Example of output:
# ./test_sysctl
Test case: sysctl wrong attach_type .. [PASS]
Test case: sysctl:read allow all .. [PASS]
Test case: sysctl:read deny all .. [PASS]
Test case: ctx:write sysctl:read read ok .. [PASS]
Test case: ctx:write sysctl:write read ok .. [PASS]
Test case: ctx:write sysctl:read write reject .. [PASS]
Summary: 6 PASSED, 0 FAILED
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add unit test to verify that program and attach types are properly
identified for "cgroup/sysctl" section name.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
pmtu.sh script runs a number of tests and dumps a summary of pass/fail.
If a test fails, it is near impossible to debug why. For example:
TEST: ipv6: PMTU exceptions [FAIL]
There are a lot of commands run behind the scenes for this test. Which
one is failing?
Add a VERBOSE option to show commands that are run and any output from
those commands. Add a PAUSE_ON_FAIL option to halt the script if a test
fails allowing users to poke around with the setup in the failed state.
In the process, rename tracing to TRACING and move declaration to top
with the new variables.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-04-12
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Improve BPF verifier scalability for large programs through two
optimizations: i) remove verifier states that are not useful in pruning,
ii) stop walking parentage chain once first LIVE_READ is seen. Combined
gives approx 20x speedup. Increase limits for accepting large programs
under root, and add various stress tests, from Alexei.
2) Implement global data support in BPF. This enables static global variables
for .data, .rodata and .bss sections to be properly handled which allows
for more natural program development. This also opens up the possibility
to optimize program workflow by compiling ELFs only once and later only
rewriting section data before reload, from Daniel and with test cases and
libbpf refactoring from Joe.
3) Add config option to generate BTF type info for vmlinux as part of the
kernel build process. DWARF debug info is converted via pahole to BTF.
Latter relies on libbpf and makes use of BTF deduplication algorithm which
results in 100x savings compared to DWARF data. Resulting .BTF section is
typically about 2MB in size, from Andrii.
4) Add BPF verifier support for stack access with variable offset from
helpers and add various test cases along with it, from Andrey.
5) Extend bpf_skb_adjust_room() growth BPF helper to mark inner MAC header
so that L2 encapsulation can be used for tc tunnels, from Alan.
6) Add support for input __sk_buff context in BPF_PROG_TEST_RUN so that
users can define a subset of allowed __sk_buff fields that get fed into
the test program, from Stanislav.
7) Add bpf fs multi-dimensional array tests for BTF test suite and fix up
various UBSAN warnings in bpftool, from Yonghong.
8) Generate a pkg-config file for libbpf, from Luca.
9) Dump program's BTF id in bpftool, from Prashant.
10) libbpf fix to use smaller BPF log buffer size for AF_XDP's XDP
program, from Magnus.
11) kallsyms related fixes for the case when symbols are not present in
BPF selftests and samples, from Daniel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ebtables -t broute allows to redirect packets in a way that
they get pushed up the stack, even if the interface is part
of a bridge.
In case of IP packets to non-local address, this means
those IP packets are routed instead of bridged-forwarded, just
as if the bridge would not have existed.
Expected test output is:
PASS: netns connectivity: ns1 and ns2 can reach each other
PASS: ns1/ns2 connectivity with active broute rule
PASS: ns1/ns2 connectivity with active broute rule and bridge forward drop
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A couple of tests are verifying a route has been removed. The helper
expects the prefix as the first part of the expected output. When
checking that a route has been deleted the prefix is empty leading
to an invalid ip command:
$ ip ro ls match
Command line is not complete. Try option "help"
Fix by moving the comparison of expected output and output to a new
function that is used by both check_route and check_route6. Use the
new helper for the 2 checks on route removal.
Also, remove the reset of 'set -x' in route_setup which overrides the
user managed setting.
Fixes: d69faad765 ("selftests: fib_tests: Add prefix route tests with metric")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 868d523535 ("bpf: add bpf_skb_adjust_room encap flags")
introduced support to bpf_skb_adjust_room for GSO-friendly GRE
and UDP encapsulation and later introduced associated test_tc_tunnel
tests. Here those tests are extended to cover UDP encapsulation also.
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Implementation of function rhashtable_insert_fast() check if its internal
helper function __rhashtable_insert_fast() returns non-NULL pointer and
seemingly return -EEXIST in such case. However, since
__rhashtable_insert_fast() is called with NULL key pointer, it never
actually checks for duplicates, which means that -EEXIST is never returned
to the user. Use rhashtable_lookup_insert_fast() hash table API instead. In
order to verify that it works as expected and prevent the problem from
happening in future, extend tc-tests with new test that verifies that no
new filters with existing key can be inserted to flower classifier.
Fixes: 1f17f7742e ("net: sched: flower: insert filter to ht before offloading it to hw")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple test that sets cb to {1,2,3,4,5} and priority to 6, runs bpf
program that fails if cb is not what we expect and increments cb[i] and
priority. When the test finishes, we check that cb is now {2,3,4,5,6}
and priority is 7.
We also test the sanity checks:
* ctx_in is provided, but ctx_size_in is zero (same for
ctx_out/ctx_size_out)
* unexpected non-zero fields in __sk_buff return EINVAL
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Test that it is possible to set an IP address on a VRF and that it is
not vetoed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend test_btf with various positive and negative tests around
BTF verification of kind Var and DataSec. All passing as well:
# ./test_btf
[...]
BTF raw test[4] (global data test #1): OK
BTF raw test[5] (global data test #2): OK
BTF raw test[6] (global data test #3): OK
BTF raw test[7] (global data test #4, unsupported linkage): OK
BTF raw test[8] (global data test #5, invalid var type): OK
BTF raw test[9] (global data test #6, invalid var type (fwd type)): OK
BTF raw test[10] (global data test #7, invalid var type (fwd type)): OK
BTF raw test[11] (global data test #8, invalid var size): OK
BTF raw test[12] (global data test #9, invalid var size): OK
BTF raw test[13] (global data test #10, invalid var size): OK
BTF raw test[14] (global data test #11, multiple section members): OK
BTF raw test[15] (global data test #12, invalid offset): OK
BTF raw test[16] (global data test #13, invalid offset): OK
BTF raw test[17] (global data test #14, invalid offset): OK
BTF raw test[18] (global data test #15, not var kind): OK
BTF raw test[19] (global data test #16, invalid var referencing sec): OK
BTF raw test[20] (global data test #17, invalid var referencing var): OK
BTF raw test[21] (global data test #18, invalid var loop): OK
BTF raw test[22] (global data test #19, invalid var referencing var): OK
BTF raw test[23] (global data test #20, invalid ptr referencing var): OK
BTF raw test[24] (global data test #21, var included in struct): OK
BTF raw test[25] (global data test #22, array of var): OK
[...]
PASS:167 SKIP:0 FAIL:0
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Extend test_verifier with various test cases around the two kernel
extensions, that is, {rd,wr}only map support as well as direct map
value access. All passing, one skipped due to xskmap not present
on test machine:
# ./test_verifier
[...]
#948/p XDP pkt read, pkt_meta' <= pkt_data, bad access 1 OK
#949/p XDP pkt read, pkt_meta' <= pkt_data, bad access 2 OK
#950/p XDP pkt read, pkt_data <= pkt_meta', good access OK
#951/p XDP pkt read, pkt_data <= pkt_meta', bad access 1 OK
#952/p XDP pkt read, pkt_data <= pkt_meta', bad access 2 OK
Summary: 1410 PASSED, 1 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull networking fixes from David Miller:
1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.
2) There have been many weird regressions in r8169 since we turned ASPM
support on, some are still not understood nor completely resolved.
Let's turn this back off for now. From Heiner Kallweit.
3) Signess fixes for ethtool speed value handling, from Michael
Zhivich.
4) Handle timestamps properly in macb driver, from Paul Thomas.
5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
and we're holding a stale protocol header pointer". From Lorenzo
Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnxt_en: Reset device on RX buffer errors.
bnxt_en: Improve RX consumer index validity check.
net: macb driver, check for SKBTX_HW_TSTAMP
qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
net: ip_gre: fix possible use-after-free in erspan_rcv
r8169: disable ASPM again
MAINTAINERS: ieee802154: update documentation file pattern
net: vrf: Fix ping failed when vrf mtu is set to 0
selftests: add a tc matchall test case
nfc: nci: Potential off by one in ->pipes[] array
NFC: nci: Add some bounds checking in nci_hci_cmd_received()
In order to have control over how many bytes are read or written
the device needs to be opened in unbuffered mode.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Three new tests added:
1. Send get random cmd, read header in 1st read, read the rest in second
read - expect success
2. Send get random cmd, read only part of the response, send another
get random command, read the response - expect success
3. Send get random cmd followed by another get random cmd, without
reading the first response - expect the second cmd to fail with -EBUSY
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Dan reported, that cleanup path in test_memcg_subtree_control()
triggers a static checker warning:
./tools/testing/selftests/cgroup/test_memcontrol.c:76 \
test_memcg_subtree_control()
error: uninitialized symbol 'child2'.
Fix this by initializing child2 and parent2 variables and
split the cleanup path into few stages.
Signed-off-by: Roman Gushchin <guro@fb.com>
Fixes: 84092dbcf9 ("selftests: cgroup: add memory controller self-tests")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
After the first run, the test case 'test_create_read' will always
fail because the file is exist and file's attr is 'S_IMMUTABLE',
open with 'O_RDWR' will always return -EPERM.
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
On smaller systems, running a test with 200 threads can take a long
time on machines with smaller number of CPUs.
Detect the number of online cpus at test runtime, and multiply that
by 6 to have 6 rseq threads per cpu preempting each other.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: linux-kselftest@vger.kernel.org
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Add a test module for the new strscpy_pad() function. Tie it into the
kselftest infrastructure for lib/ tests.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
kselftest runs as a userspace process. Sometimes we need to test things
from kernel space. One way of doing this is by creating a test module.
Currently doing so requires developers to write a bunch of boiler plate
in the module if kselftest is to be used to run the tests. This means
we currently have a load of duplicate code to achieve these ends. If we
have a uniform method for implementing test modules then we can reduce
code duplication, ensure uniformity in the test framework, ease code
maintenance, and reduce the work required to create tests. This all
helps to encourage developers to write and run tests.
Add a C header file that can be included in test modules. This provides
a single point for common test functions/macros. Implement a few macros
that make up the start of the test framework.
Add documentation for new kselftest header to kselftest documentation.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Currently if we wish to use kselftest to run tests within a kernel
module we write a small script to load/unload and do error reporting.
There are a bunch of these under tools/testing/selftests/lib/ that are
all identical except for the test name. We can reduce code duplication
and improve maintainability if we have one version of this. However
kselftest requires an executable for each test. We can move all the
script logic to a central script then have each individual test script
call the main script.
Oneliner to call kselftest_module.sh courtesy of Kees, thanks!
Add test runner creation script. Convert
tools/testing/selftests/lib/*.sh to use new test creation script.
Testing
-------
Configure kselftests for lib/ then build and boot kernel. Then run
kselftests as follows:
$ cd /path/to/kernel/tree
$ sudo make O=$output_path -C tools/testing/selftests TARGETS="lib" run_tests
and also
$ cd /path/to/kernel/tree
$ cd tools/testing/selftests
$ sudo make O=$output_path TARGETS="lib" run_tests
and also
$ cd /path/to/kernel/tree
$ cd tools/testing/selftests
$ sudo make TARGETS="lib" run_tests
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Add tests for ipv6 gateway with ipv4 route. Tests include basic
single path with ping to verify connectivity and multipath.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With older nft versions, this will cause:
[..]
PASS: ipv6 ping to ns1 was ip6 NATted to ns2
/dev/stdin:4:30-31: Error: syntax error, unexpected to, expecting newline or semicolon
ip daddr 10.0.1.99 dnat ip to 10.0.2.99
^^
SKIP: inet nat tests
PASS: ip IP masquerade for ns2
[..]
as there is currently no way to detect if nft will be able to parse
the inet format.
redirect and masquerade tests need to be skipped in this case for inet
too because nft userspace has overzealous family check and rejects their
use in the inet family.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Overwrite retains the security state after completion of operation. Fix
nfit_test to reflect this so that the kernel can test the behavior it is
more likely to see in practice.
Fixes: 926f74802c ("tools/testing/nvdimm: Add overwrite support for nfit_test")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The k/uprobe_sytax_errors test case defines a check_error() function
used to run a command and check the position of the caret in the
output.
This would be useful for other ftrace facilities too, so move it to
test.d/functions for use by anyone. In the process, rename it to
ftrace_errlog_check() and parametrize it for general use.
Link: http://lkml.kernel.org/r/9f88080a06f1755811f69081926afe7e5cb53178.1554072478.git.tom.zanussi@linux.intel.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add error_log testcase for error logs on probe events.
This tests most of error cases and checks the error position
is correct.
Link: http://lkml.kernel.org/r/63d695b74e0965988fa54ffa12beeb2c3475250d.1554072478.git.tom.zanussi@linux.intel.com
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
[tom.zanussi@linux.intel.com: changed >& redirection to 2>]
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
after previous changes, xfrm_mode contains no function pointers anymore
and all modules defining such struct contain no code except an init/exit
functions to register the xfrm_mode struct with the xfrm core.
Just place the xfrm modes core and remove the modules,
the run-time xfrm_mode register/unregister functionality is removed.
Before:
text data bss dec filename
7523 200 2364 10087 net/xfrm/xfrm_input.o
40003 628 440 41071 net/xfrm/xfrm_state.o
15730338 6937080 4046908 26714326 vmlinux
7389 200 2364 9953 net/xfrm/xfrm_input.o
40574 656 440 41670 net/xfrm/xfrm_state.o
15730084 6937068 4046908 26714060 vmlinux
The xfrm*_mode_{transport,tunnel,beet} modules are gone.
v2: replace CONFIG_INET6_XFRM_MODE_* IS_ENABLED guards with CONFIG_IPV6
ones rather than removing them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This is a follow up of the commit 0db6f8befc ("net/sched: fix ->get
helper of the matchall cls").
To test it:
$ cd tools/testing/selftests/tc-testing
$ ln -s ../plugin-lib/nsPlugin.py plugins/20-nsPlugin.py
$ ./tdc.py -n -e 2638
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is split in two, the first part checks if a report creates a
corresponding mdb entry and if traffic is properly forwarded to it, and
the second part checks if the mdb entry is deleted after a leave and
if traffic is *not* forwarded to it. Since the mcast querier is enabled
we should see standard mcast snooping bridge behaviour.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Test the case when reg->smax_value is too small/big and can overflow,
and separately min and max values outside of stack bounds.
Example of output:
# ./test_verifier
#856/p indirect variable-offset stack access, unbounded OK
#857/p indirect variable-offset stack access, max out of bound OK
#858/p indirect variable-offset stack access, min out of bound OK
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Test that verifier rejects indirect stack access with variable offset in
unprivileged mode and accepts same code in privileged mode.
Since pointer arithmetics is prohibited in unprivileged mode verifier
should reject the program even before it gets to helper call that uses
variable offset, at the time when that variable offset is trying to be
constructed.
Example of output:
# ./test_verifier
...
#859/u indirect variable-offset stack access, priv vs unpriv OK
#859/p indirect variable-offset stack access, priv vs unpriv OK
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Test that verifier rejects indirect access to uninitialized stack with
variable offset.
Example of output:
# ./test_verifier
...
#859/p indirect variable-offset stack access, uninitialized OK
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull networking fixes from David Miller:
1) Several hash table refcount fixes in batman-adv, from Sven
Eckelmann.
2) Use after free in bpf_evict_inode(), from Daniel Borkmann.
3) Fix mdio bus registration in ixgbe, from Ivan Vecera.
4) Unbounded loop in __skb_try_recv_datagram(), from Paolo Abeni.
5) ila rhashtable corruption fix from Herbert Xu.
6) Don't allow upper-devices to be added to vrf devices, from Sabrina
Dubroca.
7) Add qmi_wwan device ID for Olicard 600, from Bjørn Mork.
8) Don't leave skb->next poisoned in __netif_receive_skb_list_ptype,
from Alexander Lobakin.
9) Missing IDR checks in mlx5 driver, from Aditya Pakki.
10) Fix false connection termination in ktls, from Jakub Kicinski.
11) Work around some ASPM issues with r8169 by disabling rx interrupt
coalescing on certain chips. From Heiner Kallweit.
12) Properly use per-cpu qstat values on NOLOCK qdiscs, from Paolo
Abeni.
13) Fully initialize sockaddr_in structures in SCTP, from Xin Long.
14) Various BPF flow dissector fixes from Stanislav Fomichev.
15) Divide by zero in act_sample, from Davide Caratti.
16) Fix bridging multicast regression introduced by rhashtable
conversion, from Nikolay Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
ibmvnic: Fix completion structure initialization
ipv6: sit: reset ip header pointer in ipip6_rcv
net: bridge: always clear mcast matching struct on reports and leaves
libcxgb: fix incorrect ppmax calculation
vlan: conditional inclusion of FCoE hooks to match netdevice.h and bnx2x
sch_cake: Make sure we can write the IP header before changing DSCP bits
sch_cake: Use tc_skb_protocol() helper for getting packet protocol
tcp: Ensure DCTCP reacts to losses
net/sched: act_sample: fix divide by zero in the traffic path
net: thunderx: fix NULL pointer dereference in nicvf_open/nicvf_stop
net: hns: Fix sparse: some warnings in HNS drivers
net: hns: Fix WARNING when remove HNS driver with SMMU enabled
net: hns: fix ICMP6 neighbor solicitation messages discard problem
net: hns: Fix probabilistic memory overwrite when HNS driver initialized
net: hns: Use NAPI_POLL_WEIGHT for hns driver
net: hns: fix KASAN: use-after-free in hns_nic_net_xmit_hw()
flow_dissector: rst'ify documentation
ipv6: Fix dangling pointer when ipv6 fragment
net-gro: Fix GRO flush when receiving a GSO packet.
flow_dissector: document BPF flow dissector environment
...
Daniel Borkmann says:
====================
pull-request: bpf 2019-04-04
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Batch of fixes to the existing BPF flow dissector API to support
calling BPF programs from the eth_get_headlen context (support for
latter is planned to be added in bpf-next), from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since, ksym_search added with verification logic for symbols existence,
it could return NULL when the kernel symbols are not loaded.
This commit will add NULL check logic after ksym_search.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, ksym_search located at trace_helpers won't check symbols are
existing or not.
In ksym_search, when symbol is not found, it will return &syms[0](_stext).
But when the kernel symbols are not loaded, it will return NULL, which is
not a desired action.
This commit will add verification logic whether symbols are loaded prior
to the symbol search.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a test to generate 1m ld_imm64 insns to stress the verifier.
Bump the size of fill_ld_abs_vlan_push_pop test from 4k to 29k
and jump_around_ld_abs from 4k to 5.5k.
Larger sizes are not possible due to 16-bit offset encoding
in jump instructions.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add 3 basic tests that stress verifier scalability.
test_verif_scale1.c calls non-inlined jhash() function 90 times on
different position in the packet.
This test simulates network packet parsing.
jhash function is ~140 instructions and main program is ~1200 insns.
test_verif_scale2.c force inlines jhash() function 90 times.
This program is ~15k instructions long.
test_verif_scale3.c calls non-inlined jhash() function 90 times on
But this time jhash has to process 32-bytes from the packet
instead of 14-bytes in tests 1 and 2.
jhash function is ~230 insns and main program is ~1200 insns.
$ test_progs -s
can be used to see verifier stats.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is a preparation for the next commit that would prohibit access to
the most fields of __sk_buff from the BPF programs.
Instead of requiring BPF flow dissector programs to look into skb,
pass all input data in the flow_keys.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When we tail call PROG(VLAN) from parse_eth_proto we don't need to peek
back to handle vlan proto because we didn't adjust nhoff/thoff yet. Use
flow_keys->n_proto, that we set in parse_eth_proto instead and
properly increment nhoff as well.
Also, always use skb->protocol and don't look at skb->vlan_present.
skb->vlan_present indicates that vlan information is stored out-of-band
in skb->vlan_{tci,proto} and vlan header is already pulled from skb.
That means, skb->vlan_present == true is not relevant for BPF flow
dissector.
Add simple test cases with VLAN tagged frames:
* single vlan for ipv4
* double vlan for ipv6
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use standard C99 %zu for sizeof, not GCC's custom %Zu:
bpf_obj_id.c:76:48: warning: invalid conversion specifier 'Z'
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
flow_dissector_load.c:55:19: warning: format string is not a string literal (potentially insecure)
[-Wformat-security]
error(1, errno, command);
^~~~~~~
flow_dissector_load.c:55:19: note: treat the string as an argument to avoid this
error(1, errno, command);
^
"%s",
1 warning generated.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This makes sure we don't put headers as input files when doing
compilation, because clang complains about the following:
clang-9: error: cannot specify -o when generating multiple output files
../lib.mk:152: recipe for target 'xxx/tools/testing/selftests/bpf/test_verifier' failed
make: *** [xxx/tools/testing/selftests/bpf/test_verifier] Error 1
make: *** Waiting for unfinished jobs....
clang-9: error: cannot specify -o when generating multiple output files
../lib.mk:152: recipe for target 'xxx/tools/testing/selftests/bpf/test_progs' failed
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For multiple dimensional arrays like below,
int a[2][3]
both llvm and pahole generated one BTF_KIND_ARRAY type like
. element_type: int
. index_type: unsigned int
. number of elements: 6
Such a collapsed BTF_KIND_ARRAY type will cause the divergence
in BTF vs. the user code. In the compile-once-run-everywhere
project, the header file is generated from BTF and used for bpf
program, and the definition in the header file will be different
from what user expects.
But the kernel actually supports chained multi-dimensional array
types properly. The above "int a[2][3]" can be represented as
Type #n:
. element_type: int
. index_type: unsigned int
. number of elements: 3
Type #(n+1):
. element_type: type #n
. index_type: unsigned int
. number of elements: 2
The following llvm commit
https://reviews.llvm.org/rL357215
also enables llvm to generated proper chained multi-dimensional arrays.
The test_btf already has a raw test ("struct test #1") for chained
multi-dimensional arrays. This patch added amended bpffs test for
chained multi-dimensional arrays.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
On top of this, a cleanup of kvm_para.h headers, which were exported by
some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcoM5VAAoJEL/70l94x66DU3EH/A8sYdsfeqALWElm2Sy9TYas
mntz+oTWsl3vDy8s8zp1ET2NpF7oBlBEMmCWhVEJaD+1qW3VpTRAseR3Zr9ML9xD
k+BQM8SKv47o86ZN+y4XALl30Ckb3DXh/X1xsrV5hF6J3ofC+Ce2tF560l8C9ygC
WyHDxwNHMWVA/6TyW3mhunzuVKgZ/JND9+0zlyY1LKmUQ0BQLle23gseIhhI0YDm
B4VGIYU2Mf8jCH5Ir3N/rQ8pLdo8U7f5P/MMfgXQafksvUHJBg6B6vOhLJh94dLh
J2wixYp1zlT0drBBkvJ0jPZ75skooWWj0o3otEA7GNk/hRj6MTllgfL5SajTHZg=
=/A7u
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"A collection of x86 and ARM bugfixes, and some improvements to
documentation.
On top of this, a cleanup of kvm_para.h headers, which were exported
by some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
KVM: doc: Document the life cycle of a VM and its resources
KVM: selftests: complete IO before migrating guest state
KVM: selftests: disable stack protector for all KVM tests
KVM: selftests: explicitly disable PIE for tests
KVM: selftests: assert on exit reason in CR4/cpuid sync test
KVM: x86: update %rip after emulating IO
x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
kvm: don't redefine flags as something else
kvm: mmu: Used range based flushing in slot_handle_level_range
KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
KVM: Reject device ioctls from processes other than the VM's creator
KVM: doc: Fix incorrect word ordering regarding supported use of APIs
KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
...
Add a zero key in order to standardize hardware that want a key of 0's to
be passed. Some platforms defaults to a zero-key with security enabled
rather than allow the OS to enable the security. The zero key would allow
us to manage those platform as well. This also adds a fix to secure erase
so it can use the zero key to do crypto erase. Some other security commands
already use zero keys. This introduces a standard zero-key to allow
unification of semantics cross nvdimm security commands.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf 2019-03-29
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Bug fix in BTF deduplication that was mishandling an equivalence
comparison, from Andrii.
2) libbpf Makefile fixes to properly link against libelf for the shared
object and to actually export AF_XDP's xsk.h header, from Björn.
3) Fix use after free in bpf inode eviction, from Daniel.
4) Fix a bug in skb creation out of cpumap redirect, from Jesper.
5) Remove an unnecessary and triggerable WARN_ONCE() in max number
of call stack frames checking in verifier, from Paul.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test different scenarios of indirect variable-offset stack access: out of
bound access (>0), min_off below initialized part of the stack,
max_off+size above initialized part of the stack, initialized stack.
Example of output:
...
#856/p indirect variable-offset stack access, out of bound OK
#857/p indirect variable-offset stack access, max_off+size > max_initialized OK
#858/p indirect variable-offset stack access, min_off < min_initialized OK
#859/p indirect variable-offset stack access, ok OK
...
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add 36 pedit action tests to check pedit options described in tc-pedit(8)
man page. Test cases can be specified by categories: actions, pedit,
raw_op, layered_op. RAW_OP cases check offset option for u8, u16 and u32
offset size. LAYERED_OP cases check fields option for eth, ip, ip6,
tcp and udp headers.
Include following tests:
377e - Add pedit action with RAW_OP offset u32
a0ca - Add pedit action with RAW_OP offset u32 (INVALID)
dd8a - Add pedit action with RAW_OP offset u16 u16
53db - Add pedit action with RAW_OP offset u16 (INVALID)
5c7e - Add pedit action with RAW_OP offset u8 add value
2893 - Add pedit action with RAW_OP offset u8 quad
3a07 - Add pedit action with RAW_OP offset u8-u16-u8
ab0f - Add pedit action with RAW_OP offset u16-u8-u8
9d12 - Add pedit action with RAW_OP offset u32 set u16 clear u8 invert
ebfa - Add pedit action with RAW_OP offset overflow u32 (INVALID)
f512 - Add pedit action with RAW_OP offset u16 at offmask shift set
c2cb - Add pedit action with RAW_OP offset u32 retain value
86d4 - Add pedit action with LAYERED_OP eth set src & dst
c715 - Add pedit action with LAYERED_OP eth set src (INVALID)
ba22 - Add pedit action with LAYERED_OP eth type set/clear sequence
5810 - Add pedit action with LAYERED_OP ip set src & dst
1092 - Add pedit action with LAYERED_OP ip set ihl & dsfield
02d8 - Add pedit action with LAYERED_OP ip set ttl & protocol
3e2d - Add pedit action with LAYERED_OP ip set ttl (INVALID)
31ae - Add pedit action with LAYERED_OP ip ttl clear/set
486f - Add pedit action with LAYERED_OP ip set duplicate fields
e790 - Add pedit action with LAYERED_OP ip set ce, df, mf, firstfrag,
nofrag fields
6829 - Add pedit action with LAYERED_OP beyond ip set dport & sport
afd8 - Add pedit action with LAYERED_OP beyond ip set icmp_type &
icmp_code
3143 - Add pedit action with LAYERED_OP beyond ip set dport (INVALID)
fc1f - Add pedit action with LAYERED_OP ip6 set src & dst
6d34 - Add pedit action with LAYERED_OP ip6 dst retain value (INVALID)
6f5e - Add pedit action with LAYERED_OP ip6 flow_lbl
6795 - Add pedit action with LAYERED_OP ip6 set payload_len, nexthdr,
hoplimit
1442 - Add pedit action with LAYERED_OP tcp set dport & sport
b7ac - Add pedit action with LAYERED_OP tcp sport set (INVALID)
cfcc - Add pedit action with LAYERED_OP tcp flags set
3bc4 - Add pedit action with LAYERED_OP tcp set dport, sport & flags
fields
f1c8 - Add pedit action with LAYERED_OP udp set dport & sport
d784 - Add pedit action with mixed RAW/LAYERED_OP #1
70ca - Add pedit action with mixed RAW/LAYERED_OP #2
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when strict priority is configured on a system, the
higher-priority traffic does actually win all the available bandwidth.
The test uses a similar approach to qos_mc_aware.sh to run and account
the traffic.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract reusable code from qos_mc_aware.sh and put into a new library.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test runs two streams of traffic from two independent ports to
create congestion on one egress port. It is necessary to configure the
shared buffer thresholds correctly, to make sure that there is traffic
from both streams in the shared buffer. Only then can the test actually
test prioritization among these streams.
Without this configuration, it is possible, that one of the streams
takes all of port-pool quota, and the other stream is not even admitted,
thus invalidating the result.
On Spectrum-1, this is not a problem, because MC traffic uses a separate
pool. But for Spectrum-2, MC and UC share the same pool, and the correct
configuration is important.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to obtain, set, and restore a pool size, and a port-pool and
tc-pool threshold.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devlink -j and jq for more accurate querying. Use cut -f-2 instead
of rev-cut-rev combo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Construct a basic topology consisting of two hosts connected using a
VLAN-aware bridge. Put each port in a different VLAN and test that ping
fails.
Add ingress and egress filters with a VLAN modify action and test that
ping passes.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send packets with VLAN and PCP set and check that TC flower filters can
match on these keys.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a packet is routed using a multicast route whose specified
ingress interface does not match the interface from which the packet was
received, the packet is dropped.
Add IPv4 and IPv6 test cases for above mentioned scenario.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/virtual/kvm/api.txt states:
NOTE: For KVM_EXIT_IO, KVM_EXIT_MMIO, KVM_EXIT_OSI, KVM_EXIT_PAPR and
KVM_EXIT_EPR the corresponding operations are complete (and guest
state is consistent) only after userspace has re-entered the
kernel with KVM_RUN. The kernel side will first finish incomplete
operations and then check for pending signals. Userspace can
re-enter the guest with an unmasked signal pending to complete
pending operations.
Because guest state may be inconsistent, starting state migration after
an IO exit without first completing IO may result in test failures, e.g.
a proposed change to KVM's handling of %rip in its fast PIO handling[1]
will cause the new VM, i.e. the post-migration VM, to have its %rip set
to the IN instruction that triggered KVM_EXIT_IO, leading to a test
assertion due to a stage mismatch.
For simplicitly, require KVM_CAP_IMMEDIATE_EXIT to complete IO and skip
the test if it's not available. The addition of KVM_CAP_IMMEDIATE_EXIT
predates the state selftest by more than a year.
[1] https://patchwork.kernel.org/patch/10848545/
Fixes: fa3899add1 ("kvm: selftests: add basic test for state save and restore")
Reported-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since 4.8.3, gcc has enabled -fstack-protector by default. This is
problematic for the KVM selftests as they do not configure fs or gs
segments (the stack canary is pulled from fs:0x28). With the default
behavior, gcc will insert a stack canary on any function that creates
buffers of 8 bytes or more. As a result, ucall() will hit a triple
fault shutdown due to reading a bad fs segment when inserting its
stack canary, i.e. every test fails with an unexpected SHUTDOWN.
Fixes: 14c47b7530 ("kvm: selftests: introduce ucall")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM selftests embed the guest "image" as a function in the test itself
and extract the guest code at runtime by manually parsing the elf
headers. The parsing is very simple and doesn't supporting fancy things
like position independent executables. Recent versions of gcc enable
pie by default, which results in triple fault shutdowns in the guest due
to the virtual address in the headers not matching up with the virtual
address retrieved from the function pointer.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...so that the test doesn't end up in an infinite loop if it fails for
whatever reason, e.g. SHUTDOWN due to gcc inserting stack canary code
into ucall() and attempting to derefence a null segment.
Fixes: ca35906688 ("kvm: selftests: add cr4_cpuid_sync_test")
Cc: Wei Huang <wei@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
