Add tracepoints to retrieve information about read, write
and non-data commands. For performance measurement support
tracepoints are added at the beginning and at the end of
transfers. Following is a list showing the new tracepoint
events. The "cmd" parameter here represents the opcode, SID,
and full 16-bit address.
spmi_write_begin: cmd and data buffer.
spmi_write_end : cmd and return value.
spmi_read_begin : cmd.
spmi_read_end : cmd, return value and data buffer.
spmi_cmd : cmd.
The reason that cmd appears at both the beginning and at
the end event is that SPMI drivers can request commands
concurrently. cmd helps in matching the corresponding
events.
SPMI tracepoints can be enabled like:
echo 1 >/sys/kernel/debug/tracing/events/spmi/enable
and will dump messages that can be viewed in
/sys/kernel/debug/tracing/trace that look like:
... spmi_read_begin: opc=56 sid=00 addr=0x0000
... spmi_read_end: opc=56 sid=00 addr=0x0000 ret=0 len=02 buf=0x[01-40]
... spmi_write_begin: opc=48 sid=00 addr=0x0000 len=3 buf=0x[ff-ff-ff]
Suggested-by: Sagar Dharia <sdharia@codeaurora.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Signed-off-by: Ankit Gupta <ankgupta@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to spmi spec a slave powers up into startup state and then
transitions into active state. Thus, the wakeup command is not required
before calling the slave's probe. The wakeup command is only needed for
slaves that are in sleep state after receiving the sleep command.
Cc: galak@codeaurora.org
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Sagar Dharia <sdharia@codeaurora.org>
Acked-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPMI defines the behavior of a device in the "SLEEP" state as being
"user-defined or specified by the device manufacturer". Without
clearly-defined bus-level semantics for low-power states, push the
responsibility of transitioning a device into/out of "SLEEP" into SPMI
device drivers.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System Power Management Interface (SPMI) is a specification
developed by the MIPI (Mobile Industry Process Interface) Alliance
optimized for the real time control of Power Management ICs (PMIC).
SPMI is a two-wire serial interface that supports up to 4 master
devices and up to 16 logical slaves.
The framework supports message APIs, multiple busses (1 controller
per bus) and multiple clients/slave devices per controller.
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: Michael Bohan <mbohan@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
