Add DSS related pinmux and display data nodes required to support
DVI video out on SBC-T3530, SBC-T3730 and SBC-T3517.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the GPMC warnings now enabled, I noticed the LAN9220 timings
can overflow the GPMC registers with 200MHz L3 speed. Earlier we
were just skipping the bad timings and would continue with the
bootloader timings. Now we no longer allow to continue with bad
timings as we have the timings in the .dts files.
We could start using the GPMC clock divider, but let's instead
use the u-boot timings that are known to be working and a bit
faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
defines deciphered. Except that we don't set gpmc,burst-length
as that's only partially configured and does not seem to work
if fully enabled.
[tony@atomide.com: updated to remove gpmc,burst-length]
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've noticed occasional random oopsing on my gateway
machine since I upgraded it to use device tree based
booting. As this machine has worked reliably before
that for a few years, pretty much the only difference
was narrowed down to the GPMC timings. Turns out that
for legacy based booting we are using bootloader timings
for GPMC for smsc911x. With device tree we are passing
the timings in the .dts file, and the device tree
timings are not quite suitable for LAN9920.
Enabling DEBUG in gpmc.c I noticed that the device tree
configured timings are different from the the known
working bootloader timings. So let's fix the timings to
match the bootloader timings when looked at the gpmc
dmesg output with DEBUG enabled.
The changes were done by multiplying the bootloader
tick values by six to get the nanosecond value for
device tree. This is not generic from the device point
of view as the calculations should be based on the device
timings. Anyways, further improvments can be done based
on the timings documentation for LAN9220. But let's first
get things to a known good working state.
Note that we still need to change the timings also for
sb-t35 also as it has two LAN9220 instances on GPMC and
we can currently include the generic timings only once.
Also note that any boards that have LAN9221 instead of
LAN9220 should be updated to use omap-gpmc-smsc9221.dtsi
instead of omap-gpmc-smsc911x.dtsi. The LAN9221 timings
are different from LAN9220 timings.
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we have wrong GPMC timings we have for the cm-t and
sbc-t boards. This can cause occasional strange errors with at
least doing an rsync of large files or doing apt-get dist-upgrade.
Let's fix the issue in two phases. First let's simplify cm-t and
sbc-t to use the shared omap-gpmc-smsc911x.dtsi to avoid fixing
the issue in multiple places. Then we can fix the timings in
a single place with a follow-up patch.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SB-T35 baseboard features SMSC9220 Ethernet chip which requires
its own power supply regulators.
Add baseboard specific regulators for the SB-T35 Ethernet chip.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds support for CompuLab SBC-T3530, also known as cm-t3730:
http://compulab.co.il/products/sbcs/sbc-t3530/
It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:
http://compulab.co.il/products/sbcs/sbc-t3517/http://compulab.co.il/products/sbcs/sbc-t3730/
So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.
I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.
Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.
Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
