Currently there are two different implementations (in the firmware) for
the QAM demodulator command: one takes 4 and the other takes 2
parameters. The driver shows an error in dmesg When using the
4-parameter command with firmware that implements the 2-parameter
command. Unfortunately this happens every time when chaning the
frequency (on DVB-C).
This patch simply makes configurable, how many command parameters will
be used. All existing drxk_config instances using the "drxk_a3.mc" were
updated because this firmware is the only loadable firmware where the
QAM demodulator command takes 4 parameters. Some firmwares in the ROM
might also use it. The drxk instances in the em28xx-dvb driver were also
updated to silence the warnings.
If no qam_demod_parameter_count is given in the drxk_config struct, then
the correct number of parameters will be auto-detected.
[mchehab@redhat.com: Fix a small CodingStyle issue at one comment]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"stat" is always zero here. The condition used to be needed, but we
shifted stuff around in 0f0b270f90 "[media] ngene: CXD2099AR Common
Interface driver".
This doesn't change how the code works, it's just a bit tidier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the ngene/ddbridge firmware into their drivers.
There are two reasons for that:
1) The firmware used there didn't work for a few devices
I tested here (Terratec H5, H6 and H7);
2) At least Terratec H7 doesn't seem to require a firmware
for it to work.
After this change, if firmware is not specified, the driver will
use a rom-based firmware (this seems to be the case for Terratec
H7, although I need to better check the USB dumps to be sure about
that).
In any case, the firmware seems to be optional, as the DRX-K driver
don't return the firmware load error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of creating two DVB frontend entries for the same device,
create just one entry, and fill the delivery_system according with
the supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In practice, it is being hard to distinguish when a patch
should go to staging tree or to the media tree. Better
to distinguish it, by putting the media drivers at a
separate staging directory. Newer staging drivers that include
anything with "dvb*.h", "v4l2*.h" or "videodev2.h" should
go to the drivers/staging/media tree.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usage of these flags has been deprecated for nearly 4 years by:
commit f77bf01425
Author: Sam Ravnborg <sam@neptun.(none)>
Date: Mon Oct 15 22:25:06 2007 +0200
kbuild: introduce ccflags-y, asflags-y and ldflags-y
Moreover, these flags (at least EXTRA_CFLAGS) have been documented for command
line use. By default, gmake(1) do not override command line setting, so this is
likely to result in build failure or unexpected behavior.
Replace their usage by Kbuild's `{as,cc,ld}flags-y'.
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the only parameter to be configured is the I2C
address. However, Terratec H5 logs shows that it needs a different
setting for some things, and it has its own firmware.
So, move the addr into a config structure, in order to allow adding
the required configuration bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the CI requires a continuous data stream, the driver inserts dummy
packets when necessary. Do not pass these packets to userspace anymore.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support DuoFlex CT with Digital Devices CineS2 and Mystique SaTiX-S2.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix return code if no demux was found (cineS2_probe).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support Digital Devices DuoFlex CT with ngene.
Signed-off-by: Ralph Metzler <rmetzler@digitaldevices.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] ngene: Fix CI data transfer regression Fix CI data transfer regression introduced by previous cleanup.
[media] v4l: make sure drivers supply a zeroed struct v4l2_subdev
[media] Missing frontend config for LME DM04/QQBOX
[media] rc_core: avoid kernel oops when rmmod saa7134
[media] imon: add conditional locking in change_protocol
[media] rc: show RC_TYPE_OTHER in sysfs
[media] ite-cir: modular build on ppc requires delay.h include
[media] mceusb: add Dell transceiver ID
Fix CI data transfer regression introduced by previous cleanup.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is abusing the kernel<=>userspace API, due to the lack of a
proper solution for it. A discussion were done at:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg22196.html
But there's not a solution for it yet. So, move the driver to staging, while
we don't have a final solution.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactored code for channel initialisation and release:
- Do not create device nodes which are not required.
- Better error handling.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add dvb net device.
Note that the physical address must be setup manually.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement shutdown workaround for some chipsets.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver for the Common Interface Controller CXD2099AR.
Supports the CI of the cineS2 DVB-S2.
For now, data is passed through '/dev/dvb/adapterX/sec0':
- Encrypted data must be written to 'sec0'.
- Decrypted data can be read from 'sec0'.
- Setup the CAM using device 'ca0'.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If tuner initialisation failed, the frontend node was not removed.
When the frontend was opened, a kernel oops occurred...
This is the first step to improve error handling during initialisation.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support up to 4 tuners for cineS2 v5, duoflex & mystique v2.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Detection class I2C_CLASS_TV_DIGITAL is set by many adapters but no
I2C device driver is setting it anymore, which means it can be
dropped. I2C devices on digital TV adapters are instantiated
explicitly these days, which is much better.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Detection class I2C_CLASS_TV_ANALOG is set by a few adapters but no
I2C device driver is setting it anymore, which means it can be
dropped. I2C devices on analog TV adapters are instantiated
explicitly these days, which is much better.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make command timeout workaround configurable,
activate it for firmware version <= 17.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add MSI support, may be enabled with firmware version 18.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is neither a good idea nor necessary to call the demuxer with interrupts disabled.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the demod and tuner dependencies required for the Avermedia m780 to the
Kconfig for the ngene driver.
Thanks to Oliver Endriss for pointing this out.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Start moving the dvb specific code to ngene-dvb.c. Note that there is still
stuff in ngene-core.c which could potentially be moved out, but it will require
considerable reworking of the logic in order to continue to properly support
DVB while also being able to support transport streams coming from analog MPEG
encoders.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split out the card profiles into a new file called ngene-cards.c. This is
part of a larger refactoring of the driver in preparation for adding analog
support.
Note that this patch makes *no* functional change - all I did was cut/paste the
code and add the function prototypes to ngene.h as needed.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split out the i2c related code from the ngene-core.c into a new file called
ngene-i2c.c. This is part of a larger refactoring of the driver in preparation
for adding analog support.
Note that this patch makes *no* functional change - all I did was cut/paste the
code and add the function prototypes to ngene.h as needed.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ATSC/QAM support for the Avermedia m780. Note that this patch does
not include any analog support for the board, as the ngene bridge driver does
not yet have analog implemented
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code assumes that channel zero is always a TS input, which would
result in an oops if the "one_adapter" modprobe option is 1 (which it is by
default) and the board in question has something else on channel zero (which
is the case for the Avermedia m780, which has it's analog input wired to UVI1)
The code now explicitly tracks the first adapter created and ensures that
other channels cannot accidentially be associated with a NULL adapter.
Also, eliminate what appears to be a typo where all of the channel parameters
are getting associated with stream zero's properties, which will work if you
happen to have a dual stream board with the exact same configuration, but if
they differ then the second stream is going to end up with the first stream's
configuration.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
