Move the definitions of constants used in the dt-bindings from
include/sound/rt5651.h to include/dt-bindings/sound/rt5651.h.
As dt-bindings headers may also be parsed by the dt-compiler, they cannot
use enums, only defines, so this commit also changes the code declaring
the constants to use defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get the insertion event before the jack is fully inserted at which point
the second ring on a TRRS connector may short the 2nd ring and sleeve
contacts. Testing has shown that this short-circuit may happen as late
as 500ms after the insertion event, but it never lasts longer then 300ms.
This commit changes the detection algorithm to require 5 identical OVCD
values in a row at 100 ms intervals to fix the jack-type sometimes getting
mis-detected.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect if
an inserted jack is a headset or headphones (mic shorted to ground).
The threshold for at which current the OVCD triggers on the rt5651 is not
only controlled by setting the absolute current limit, but also by setting
a scale factor which applies to the limit. Testing has shown that we need
to set both (depending on the board).
This commit adds support for the sofar unused OVCD scale-factor register
and adds support for specifying non-default values for it through the
"realtek,over-current-scale-factor" device-property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect
if an inserted jack is a headset or headphones (mic shorted to ground).
Some boards may need different values for the OVCD current threshold
because of a resistor on the board in serial with or parallel to the
jack mic contact.
This commit adds support for configuring the OCVD current threshold
through the "realtek,over-current-threshold-microamp" device-property.
Note this commit changes the default value from 600uA to 2000uA,
because testing has shown 600uA to be a poor default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The idea behind exporting rt5651_apply_properties(), was for it to be used
on platforms where the platform code may need to add device-properties,
rather then relying only on properties set by the firmware. The platform
code could then call rt5651_apply_properties() after adding properties to
make sure that the codec driver was aware of the new properties.
But this is not necessary, as long as we do all property parsing from
the codec component-driver's probe function (or later) then the machine
driver can attach properties before calling snd_soc_register_card and
calling rt5651_apply_properties() for ordering reasons is not necessary.
This commit makes rt5651_apply_properties() private and adds 2 comments
documenting that all property parsing must be done from the codec
component-driver's probe function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the applying of the differential input and dmic properties to a new
rt5651_apply_properties() helper function. This new function can be called
by platform code which attaches properties after probe() has run to apply
these new properties.
Note this also moves the time when we apply these properties for DT
platforms from i2c-probe to snd-component-probe time, this should not
result in any functional difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard component set_jack callback instead of defining a codec
private API for this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all jack-detect initialization to rt5651_set_jack_detect. The main
reason to do this is so that platform code can setup jack-detect properties
after the device has been probed, which unfortunately is necessary on some
platforms.
This has 2 additional advantages:
1) Grouping all jack-detect init together makes it easier to follow what
is happening and results in a small reduction in the number of loc.
2) Before we would register the irq handler before rt5651->hp_jack was
assigned, leading to a potential NULL deref if the jack_detect work runs
before the machine driver has called set_jack.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in tree users of platform-data for the rt5651 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the function of the PLL clock calculation to RL6231 shared
support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
