The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131453.1961-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131450.1910-1-luc.vanoostenryck@gmail.com
The ADV7511 has four 256-byte maps that can be accessed via the main I2C
ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1518544137-2742-6-git-send-email-kbingham@kernel.org
Some of the platform-specific stuff in rockchip_dp_poweron() needs to
happen before the generic code. Some needs to happen after. Let's
split the callback in two.
Specifically we can't start doing PSR work until _after_ the whole
controller is up, so don't set the enable until the end.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[seanpaul added exynos change]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-23-enric.balletbo@collabora.com
The comments in analogix_dp_init_aux() claim that we're disabling aux
channel retries, but then right below it for Rockchip it sets them to
3. If we actually need 3 retries for Rockchip then we could adjust
the comment, but it seems more likely that we want the same retry
behavior across all platforms.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-21-enric.balletbo@collabora.com
The code in analogix_dp_transfer() that was supposed to print out:
AUX CH error happened
Was actually dead code. That's because the previous check (whether
the interrupt status indicated any errors) would have hit for all
errors anyway.
Let's combine the two error checks so we can actually see AUX CH
errors. We'll also downgrade the message to a warning since some of
these types of errors might be expected for some displays. If this
gets too noisy we can downgrade again to debug.
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-20-enric.balletbo@collabora.com
The current user of the analogix power_off is "analogix_dp-rockchip".
That driver does this:
- deactivate PSR
- turn off a clock
Both of these things (especially deactive PSR) should be done before
we turn the PHY power off and turn off analog power. Let's move the
callback up.
Note that without this patch (and with
https://patchwork.kernel.org/patch/9553349/ [seanpaul: this patch was
not applied, but it seems like the race can still occur]), I experienced
an error in reboot testing where one thread was at:
rockchip_drm_psr_deactivate
rockchip_dp_powerdown
analogix_dp_bridge_disable
drm_bridge_disable
...and the other thread was at:
analogix_dp_send_psr_spd
analogix_dp_enable_psr
analogix_dp_psr_set
psr_flush_handler
The flush handler thread was finding AUX channel errors and eventually
reported "Failed to apply PSR", where I had a kgdb breakpoint. Presumably
the device would have eventually given up and shut down anyway, but it
seems better to fix the order to be more correct.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-19-enric.balletbo@collabora.com
It's too early to detect fast link training, if other step after it
failed, we will set fast_link flag to 1, and retry set_bridge again. In
this case we will power down and power up panel power supply, and we
will do fast link training since we have set fast_link flag to 1. In
fact, we should do full link training now, not the fast link training.
So we should move the fast link detection at the end of set_bridge.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-18-enric.balletbo@collabora.com
Register ANALOGIX_DP_FUNC_EN_1(offset 0x18), Rockchip is different to
Exynos:
on Exynos edp phy,
BIT 7 MASTER_VID_FUNC_EN_N
BIT 6 reserved
BIT 5 SLAVE_VID_FUNC_EN_N
on Rockchip edp phy,
BIT 7 reserved
BIT 6 RK_VID_CAP_FUNC_EN_N
BIT 5 RK_VID_FIFO_FUNC_EN_N
So, we should do some private operations to Rockchip.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-17-enric.balletbo@collabora.com
The STRM_VALID bit in register ANALOGIX_DP_SYS_CTL_3 may be unstable,
so we may hit the error log "Timeout of video streamclk ok" since
checked this unstable bit.
In fact, we can go continue and the streamclk is ok if we wait enough time,
it does no effect on display.
Let's change this error to warn.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-16-enric.balletbo@collabora.com
There is no register named ANALOGIX_DP_PLL_CTL in Rockchip edp phy reg
list. We should use BIT_4 in ANALOGIX_DP_PD to control the pll power
instead of ANALOGIX_DP_PLL_CTL.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-15-enric.balletbo@collabora.com
If we failed disable psr, it would hang the display until next psr
cycle coming. So we should restore psr->state when it failed.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-14-enric.balletbo@collabora.com
AUX errors are caused by many different reasons. We may not know what
happened in aux channel on failure, so let's reset aux channel if some
errors occurred.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-13-enric.balletbo@collabora.com
There are some different bits between Rockchip and Exynos in register
"AUX_PD". This patch fixes the incorrect operations about it.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-12-enric.balletbo@collabora.com
We need to check the dpcd write/read return value to see whether the
write/read was successful
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-11-enric.balletbo@collabora.com
Enhanced mode is required by the eDP 1.2 specification, and not doing it
early could result in a period of time where we have a link transmitting
idle packets without it. Since there is no reason to disable it, we just
enable it at the beginning of link training and then keep it on all the
time.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-10-enric.balletbo@collabora.com
There was a 1ms delay to detect the hpd signal, which is too short to
detect a short pulse. This patch extends this delay to 100ms.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-9-enric.balletbo@collabora.com
When panel is shut down, we should make sure edp can be disabled to avoid
undefined behavior.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-8-enric.balletbo@collabora.com
Following the correct power up sequence:
dp_pd=ff => dp_pd=7f => wait 10us => dp_pd=00
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-7-enric.balletbo@collabora.com
According to DP spec v1.3 chap 3.5.1.2 Link Training, Link Policy Maker
must first detect that the HPD signal is asserted high by the Downstream
Device before establishing a link with it.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-6-enric.balletbo@collabora.com
When we enable bridge failed, we have to retry it, otherwise we would get
the abnormal display.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-5-enric.balletbo@collabora.com
Panel would reset its setting when it powers down. It would forget the last
succeeded link training setting. So we can't use the last successful link
training setting to do fast link training. Let's reset fast_train_enable in
analogix_dp_bridge_disable();
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-4-enric.balletbo@collabora.com
We should check AUX_EN bit to confirm the AUX CH operation is completed.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-3-enric.balletbo@collabora.com
We need to enable video before analogix_dp_is_video_stream_on(), so
we can get the right video stream status.
We needed to increase the delay in the timeout loop because there is
random "Timeout of video streamclk ok" message happen when debug edp
panel, this time do not define in the spec.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-2-enric.balletbo@collabora.com
Add a driver for Cadence DPI -> DSI bridge.
This driver only support a subset of Cadence DSI bridge capabilities.
This driver has been tested/debugged in a simulated environment which
explains why some of the features are missing. Here is a
non-exhaustive list of missing features:
* burst mode
* DPHY init/configuration steps
* support for additional input interfaces (SDI input)
DSI commands and non-burst video mode have been tested.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421070846.10330-1-boris.brezillon@bootlin.com
The cable_plugin member never receives an assignment, so it is always
false, which causes hdmi_enable_overflow_interrupts() to never
be called as per the logic below:
if (hdmi->cable_plugin && hdmi->sink_is_hdmi)
hdmi_enable_overflow_interrupts(hdmi);
This has been the case since the driver was originally introduced
in commit 9aaf880ed4 ("imx-drm: Add mx6 hdmi transmitter support").
Remove the cable_plugin element and the hdmi_enable_overflow_interrupts()
function that is never called.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # On R-Car H3
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1518812170-22687-1-git-send-email-festevam@gmail.com
We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only important to do when we're entering PSR, since we want to
be sure the last frame we pushed is being served from the panel's
internal fb before shutting down the soc blocks (vop/analogix).
This patch changes the behavior such that we only wait for the
panel to complete the PSR transition when we're entering PSR, and
to skip verification when we're exiting.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-7-enric.balletbo@collabora.com
We would meet a short black screen when exit PSR with the full link
training, In this case, we should use fast link train instead of full
link training.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[dropped header reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-6-enric.balletbo@collabora.com
There is a race between AUX CH bring-up and enabling bridge which will
cause link training to fail. To avoid hitting it, don't change psr state
while enabling the bridge.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[seanpaul fixed up the commit message a bit and renamed *_supported to *_enabled]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-4-enric.balletbo@collabora.com
Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we failed to apply the
requested PSR setting.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul changed timeout loop to a readx poll]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-2-enric.balletbo@collabora.com
The following happens when connection a DVI output driven
from the SiI9022 using a DVI-to-VGA adapter plug:
i2c i2c-0: sendbytes: NAK bailout.
i2c i2c-0: sendbytes: NAK bailout.
Then no picture. Apparently the I2C engine inside the SiI9022
is not smart enough to try to fall back to DDC I2C. Or the
vendor have not integrated the electronics properly. I don't
know which one it is.
After this, the I2C bus seems stalled and the first attempt to
read the status register fails, and the code returns with
negative return value, and the display fails to initialized.
Instead, retry status readout five times and continue even
if this fails.
Tested on the ARM Versatile Express with a DVI-to-VGA
connector, it now gives picture.
Introduce a helper struct device *dev variable to make
the code more readable.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305101702.13441-1-linus.walleij@linaro.org
If there is another bridge after analogix_dp, then the connector object
should not be created. This fixes following timeouts on Exynos5420-based
Chromebook2 Peach-PIT board during boot:
exynos-dp 145b0000.dp-controller: AUX CH cmd reply timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305085741.18896-4-m.szyprowski@samsung.com
The bridge does not need to be powered in analogix_dp_bind(), so
remove the calls to pm_runtime_get()/phy_power_on()/analogix_dp_init_dp()
as well as their power-off counterparts.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[the patch originally just removed the power_on portion, seanpaul removed
the power off code as well as improved the commit message]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305085741.18896-2-m.szyprowski@samsung.com
The Amlogic Meson GX SoCs, embedded the v2.01a controller, has been also
identified needing this workaround.
This patch adds the corresponding version to enable a single iteration for
this specific version.
Fixes: be41fc55f1 ("drm: bridge: dw-hdmi: Handle overflow workaround based on device version")
Acked-by: Archit Taneja <architt@codeaurora.org>
[narmstrong: s/identifies/identified and rebased against Jernej's change]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519386277-25902-1-git-send-email-narmstrong@baylibre.com
The readl_poll_timeout() return value is 0 in case of success
so it is better to detect errors without taking care of the
return value sign.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180204213624.18288-1-philippe.cornu@st.com
Since we are initing connector in the core driver and encoder in the
plat driver, let's clean them up in the right places.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110162348.22765-3-thierry.escande@collabora.com
The driver that instantiates the bridge should own the drvdata, as all
driver model callbacks (probe, remove, shutdown, PM ops, etc.) are also
owned by its driver struct. Moreover, storing two different pointer
types in driver data depending on driver initialization status is barely
a good practice and in fact has led to many bugs in this driver.
Let's clean up this mess and change Analogix entry points to simply
accept some opaque struct pointer, adjusting their users at the same
time to avoid breaking the compilation.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110162348.22765-2-thierry.escande@collabora.com
dw_hdmi shouldn't set drvdata since some drivers might need to store
it's own data there. Rework dw_hdmi in a way to return struct dw_hdmi
instead to store it in drvdata. This way drivers are responsible to
store and pass structure when needed.
Idea was taken from the following commit:
8242ecbd59 ("drm/bridge/synopsys: stop clobbering drvdata")
Cc: p.zabel@pengutronix.de
Cc: Laurent.pinchart@ideasonboard.com
Cc: hjc@rock-chips.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-6-jernej.skrabec@siol.net
Parts of PHY code could be useful also for custom PHYs. For example,
Allwinner A83T has custom PHY which is probably Synopsys gen2 PHY
with few additional memory mapped registers, so most of the Synopsys PHY
related code could be reused.
Functions exported here are actually not specific to Synopsys PHYs but
to DWC HDMI controller PHY interface. This means that even if the PHY is
completely custom, i.e. not designed by Synopsys, exported functions can
be useful.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-5-jernej.skrabec@siol.net
Allwinner SoCs have dw hdmi controller v1.32a which exhibits same
magenta line issue as i.MX6Q and i.MX6DL. Enable workaround for it.
Tests show that one iteration is enough.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-4-jernej.skrabec@siol.net
Add support for the Synopsys DesignWare MIPI DSI version 1.31
Two registers need to be updated/added for supporting 1.31:
* PHY_TMR_CFG 0x9c (updated)
1.30 [31:24] phy_hs2lp_time
[23:16] phy_lp2hs_time
[14: 0] max_rd_time
1.31 [25:16] phy_hs2lp_time
[ 9: 0] phy_lp2hs_time
* PHY_TMR_RD_CFG 0xf4 (new)
1.31 [14: 0] max_rd_time
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206084251.303-1-philippe.cornu@st.com
The dw_mipi_dsi_host_transfer() must return the number of
bytes transmitted/received on success instead of 0.
Note: As the read feature is not implemented, only the
transmitted number of bytes is returned for the moment.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-3-philippe.cornu@st.com
The dcs/generic dsi read feature is not yet implemented so it
is important to warn the host_transfer() caller in case of
read operation requests.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-2-philippe.cornu@st.com
It's been a while since we've backmerged drm-next. Dave just brought
back 4.15-rc8, so now's a good time to freshen things up around here.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
