We need to treat built-in peripherals and bus based address ranges
differently. Local built-in peripherals (and the ColdFire SoC parts
have quite a lot of them) are always native endian - which is big
endian on m68k/ColdFire. Bus based address ranges, like the PCI bus,
are accessed little endian - so we need to byte swap those.
So implement readw/writew and readl/writel functions to deal with
memory mapped accesses correctly based on the address range being
accessed.
This fixes readw/writew and readl/writel so that they can be used in
drivers for native SoC hardware modules (many of which are shared with
other architectures (ARM in Freescale SoC parts for example). And also
drivers for PCI devices.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Some ColdFire platforms do have real PCI buses, so we should not be
re-defining or otherwise mangling the IO access functions for them.
So when CONFIG_PCI is true use the real io.h support.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
All the ColdFire IO access support code has been moved to io_no.h.
This means that all ColdFire support is at least now consistent no
matter whether the MMU is enabled or not for them.
Now that io_mm.h has reverted to only support the traditional m68k MMU
enabled processors we can remove the ColdFire specific definitions.
We can also remove the old ColdFire PCI bus IO access functions.
The new io_no.h uses asm-generic/io.h to provide all the basic support.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Use the io_no.h IO access support for all ColdFire systems, no matter
whether configured with MMU enabled or disabled. Previously there was
subtle differences in IO access functions used in both cases, and these
resulted in broken behavior for some drivers.
As observed and reported by Angelo when using MMU enabled systems the
read/write family of functions was using little endian access, while the
non-MMU enabled systems were using native endian. This results in drivers
that are shared across Freescale processors (for some of the common
internal SoC peripherals) not working - since they are wired up for native
endian access.
This problem brings to light issues with PCI bus access and local
peripheral access - but these are not addressed with this fix.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Ultimately we want the ColdFire IO access support to be consisent no matter
whether it is configured with MMU enabled or disabled. To acheive that we
need to get all the ColdFire IO access support code together in one place,
in this case io_no.h. The last big piece not in io_no.h is the PCI bus
support functions.
Define the IO mapping addresses required to use the asm-generic IO
access functions. They can provide everything we need - no need for us
to duplicate or have local in/out or read/write access functions.
Note that this support is not active yet, since we haven't done the
full switch over to using the asm-generic functions yet. And also note
that we do not yet remove the old PCI functions from io_mm.h yet.
Consolodating all this IO access support in a single place will make
it easier in the future to enable PCI bus support for non-MMU enabled
ColdFire (which we currently cannot do).
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Create a new header file, kmap.h, that groups all the definitions and
functions associated with the io mapping and remapping.
Currently the functions are spread across raw_io.h and io_mm.h. And in
the future we will want to use these in io_no.h as well. So it makes
sense to move them all together into a single header file.
It is named after the arch/m68k/mm/kmap.c file that actually implements
many of the exported functions.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The primary and fundamental access macros are really the __raw versions.
So make them the actual implementation for access, and not the read/write
access macros. The read/write macros and functions are built on top of
the raw access (with byte swapping or other actions as required).
This in itself causes no functional change right now. But it will make it
easier to fix and resolve problems with PCI bus access in the future.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
There is nothing really special about the non-MMU m68k IO access functions.
So we can easily switch to using the asm-generic/io.h functions.
The only thing we do need to handle is that historically the m68k IO access
functions for readw/readl/writew/writel use native CPU endian ordering. So
for us on m68k/ColdFire that means they are big-endian. Leave the existing
set of _raw_read/__raw_write and read/write macros in place to deal with
them. (They are ripe for later cleanup, but that is for another patch).
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The non-MMU and ColdFire IO access functions will be moving to using the
asm-generic/io.h in the near future. To make that possible we need define
guards around the m68k specific virt_to_phys() and phys_to_virt()
functions.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Move a copy of the definitions of the *_relaxed() macros into io_no.h
and io_mm.h. This precedes a change to the io_no.h file to use
asm-generic/io.h. They will be removed from io_no.h at that point.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping. __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.
On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.
On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.
Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.
This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.
Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Revive support for 64-bit get_user(), which was disabled in commit
d94af931af ("[PATCH] m68k: clean up uaccess.h") due to a "broken"
typeof in (then brand new) gcc-4.1.
- Keep on using u64 for the temporary, as __typeof__() doesn't drop
the const qualifier,
- Move it into a union (like mips32 does) to get rid of the cast, as
using get_user() to fetch a __user pointer would cause a "cast to
pointer from integer of different size" warning otherwise.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Martijn Coenen <maco@android.com>
ndelay() is supposed to take an unsigned long, but if you define
ndelay() as a macro and the caller pass an unsigned long long instead
of an unsigned long, the unsigned long long to unsigned long cast is
not done and we end up with an "undefined reference to `__udivdi3'"
error at link time.
Fix that by making ndelay() an inline function and then defining dummy
ndelay() macro that redirects to the ndelay() function (it's how most
archs do to implement ndelay()).
Fixes: c8ee038bd1 ("m68k: Implement ndelay() based on the existing udelay() logic")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
[geert: Remove comment now it is no longer a macro]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
We have two ways of getting the current time from a platform at boot
or during suspend: either using read_persistent_clock() or the rtc
class operation. We never need both, so I'm hiding the
read_persistent_clock variant when the generic RTC is enabled.
Since read_persistent_clock() and mktime() are deprecated because of
the y2038 overflow of time_t, we should use the time64_t based
replacements here.
Finally, the dependency on CONFIG_ARCH_USES_GETTIMEOFFSET looks
completely bogus in this case, so let's remove that. It was
added in commit b13b3f51ff ("m68k: fix inclusion of
arch_gettimeoffset for non-MMU 68k classic CPU types") to deal
with arch_gettimeoffset(), which has since been removed from
this file and is unrelated to the RTC functions.
The rtc accessors are only used by classic machines, while
coldfire uses proper RTC drivers, so we can put the old
ifdef back around both functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This fixes a bug in read_persistent_clock() which causes the system
clock to lag the Real Time Clock by one month. The problem was noticed
on a Mac, but theoretically it must also affect Atari, BVME6000 and Q40.
The tm_mon value in the struct rtc_time passed to mach_hwclk() is
zero-based, and atari_mste_hwclk(), atari_tt_hwclk(), bvme6000_hwclk(),
mac_hwclk() and q40_hwclk() all make this adjustment. Unfortunately,
dn_dummy_hwclk(), mvme147_hwclk(), mvme16x_hwclk(), sun3_hwclk() and
sun3x_hwclk() fail to decrement tm_mon. Also m68328_hwclk() assumes
a one-based tm_mon.
Bring these platforms into line and fix read_persistent_clock() so it
works correctly on all m68k platforms.
The datasheets for the RTC devices found on the affected platforms
all confirm that the year is stored as a value in the range 0-99 and
the month is stored as a value in the range 1-12. Please refer to the
datasheets for MC146818 (Apollo), DS1643 (MVME), ICM7170 (Sun 3)
and M48T02 (Sun 3x).
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This was used by the ide, scsi and networking code in the past to
determine if they should bounce payloads. Now that the dma mapping
always have to support dma to all physical memory (thanks to swiotlb
for non-iommu systems) there is no need to this crude hack any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Palmer Dabbelt <palmer@sifive.com> (for riscv)
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Filling in struct siginfo before calling force_sig_info a tedious and
error prone process, where once in a great while the wrong fields
are filled out, and siginfo has been inconsistently cleared.
Simplify this process by using the helper force_sig_fault. Which
takes as a parameters all of the information it needs, ensures
all of the fiddly bits of filling in struct siginfo are done properly
and then calls force_sig_info.
In short about a 5 line reduction in code for every time force_sig_info
is called, which makes the calling function clearer.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Call clear_siginfo to ensure every stack allocated siginfo is properly
initialized before being passed to the signal sending functions.
Note: It is not safe to depend on C initializers to initialize struct
siginfo on the stack because C is allowed to skip holes when
initializing a structure.
The initialization of struct siginfo in tracehook_report_syscall_exit
was moved from the helper user_single_step_siginfo into
tracehook_report_syscall_exit itself, to make it clear that the local
variable siginfo gets fully initialized.
In a few cases the scope of struct siginfo has been reduced to make it
clear that siginfo siginfo is not used on other paths in the function
in which it is declared.
Instances of using memset to initialize siginfo have been replaced
with calls clear_siginfo for clarity.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
We have a couple of files that try to include asm/compat.h on
architectures where this is available. Those should generally use the
higher-level linux/compat.h file, but that in turn fails to include
asm/compat.h when CONFIG_COMPAT is disabled, unless we can provide
that header on all architectures.
This adds the asm/compat.h for all remaining architectures to
simplify the dependencies.
Architectures that are getting removed in linux-4.17 are not changed
here, to avoid needless conflicts with the removal patches. Those
architectures are broken by this patch, but we have already shown
that they have no users.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull m68knommu update from Greg Ungerer:
"Only a single fix to set the DMA masks in the ColdFire FEC platform
data structure.
This stops the warning from dma-mapping.h at boot time"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: set dma and coherent masks for platform FEC ethernets
Pull siginfo updates from Eric Biederman:
"The work on cleaning up and getting the bugs out of siginfo generation
was largely stalled this round. The progress that was made was the
definition of FPE_FLTUNK. Which is usable to fix many of the cases
where siginfo generation is erroneously generating SI_USER by setting
si_code to 0, that has recently been tagged as FPE_FIXME.
You already have the change by way of the arm64 tree as that
definition was pulled into the arm64 tree to allow fixing the problem
there.
What remains is the second round of fixing for what I thought was a
trivial change to the struct siginfo when put the union in _sigfault
where it belongs. Do to historical reasons 32bit m68k only ensures
that pointers are 2 byte aligned. So I have added a m68k test case
made of BUILD_BUG_ONs to verify I have this fix correct and possibly
catch problems, and I have computed the number of bytes of padding
needed for the _addr_bnd and _addr_pkey cases and just use an array of
characters that size.
For pure paranoia I have written the code so if there is an
architecture out there that does not perform any alignment of
structures it should still work.
With the removal of all of the stale arechitectures this cycle future
work on cleaning up struct siginfo should be much easier. Almost all
of the conflicting si_code definitions have been removed with the
removal of (blackfin, tile, and frv). Plus some of the most difficult
to test cases have simply been removed from the tree.
Which means that with a little luck copy_siginfo_to_user can become a
light weight wrapper around copy_to_user in the next cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
m68k: Verify the offsets in struct siginfo never change.
signal: Correct the offset of si_pkey and si_lower in struct siginfo on m68k
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
Pull removal of in-kernel calls to syscalls from Dominik Brodowski:
"System calls are interaction points between userspace and the kernel.
Therefore, system call functions such as sys_xyzzy() or
compat_sys_xyzzy() should only be called from userspace via the
syscall table, but not from elsewhere in the kernel.
At least on 64-bit x86, it will likely be a hard requirement from
v4.17 onwards to not call system call functions in the kernel: It is
better to use use a different calling convention for system calls
there, where struct pt_regs is decoded on-the-fly in a syscall wrapper
which then hands processing over to the actual syscall function. This
means that only those parameters which are actually needed for a
specific syscall are passed on during syscall entry, instead of
filling in six CPU registers with random user space content all the
time (which may cause serious trouble down the call chain). Those
x86-specific patches will be pushed through the x86 tree in the near
future.
Moreover, rules on how data may be accessed may differ between kernel
data and user data. This is another reason why calling sys_xyzzy() is
generally a bad idea, and -- at most -- acceptable in arch-specific
code.
This patchset removes all in-kernel calls to syscall functions in the
kernel with the exception of arch/. On top of this, it cleans up the
three places where many syscalls are referenced or prototyped, namely
kernel/sys_ni.c, include/linux/syscalls.h and include/linux/compat.h"
* 'syscalls-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux: (109 commits)
bpf: whitelist all syscalls for error injection
kernel/sys_ni: remove {sys_,sys_compat} from cond_syscall definitions
kernel/sys_ni: sort cond_syscall() entries
syscalls/x86: auto-create compat_sys_*() prototypes
syscalls: sort syscall prototypes in include/linux/compat.h
net: remove compat_sys_*() prototypes from net/compat.h
syscalls: sort syscall prototypes in include/linux/syscalls.h
kexec: move sys_kexec_load() prototype to syscalls.h
x86/sigreturn: use SYSCALL_DEFINE0
x86: fix sys_sigreturn() return type to be long, not unsigned long
x86/ioport: add ksys_ioperm() helper; remove in-kernel calls to sys_ioperm()
mm: add ksys_readahead() helper; remove in-kernel calls to sys_readahead()
mm: add ksys_mmap_pgoff() helper; remove in-kernel calls to sys_mmap_pgoff()
mm: add ksys_fadvise64_64() helper; remove in-kernel call to sys_fadvise64_64()
fs: add ksys_fallocate() wrapper; remove in-kernel calls to sys_fallocate()
fs: add ksys_p{read,write}64() helpers; remove in-kernel calls to syscalls
fs: add ksys_truncate() wrapper; remove in-kernel calls to sys_truncate()
fs: add ksys_sync_file_range helper(); remove in-kernel calls to syscall
kernel: add ksys_setsid() helper; remove in-kernel call to sys_setsid()
kernel: add ksys_unshare() helper; remove in-kernel calls to sys_unshare()
...
A change to the generic struct siginfo accidentally changed the offset
of si_offset. Add build time checks to ensure the offsets of all known
fields in struct siginfo never change. This copies the form of similar
changes on x86.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Using this helper allows us to avoid the in-kernel calls to the
sys_mmap_pgoff() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_mmap_pgoff().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As of commit 205e1b7f51 ("dma-mapping: warn when there is no
coherent_dma_mask") the Freescale FEC driver is issuing the following
warning on driver initialization on ColdFire systems:
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 0x40159e20
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc7-dirty #4
Stack from 41833dd8:
41833dd8 40259c53 40025534 40279e26 00000003 00000000 4004e514 41827000
400255de 40244e42 00000204 40159e20 00000009 00000000 00000000 4024531d
40159e20 40244e42 00000204 00000000 00000000 00000000 00000007 00000000
00000000 40279e26 4028d040 40226576 4003ae88 40279e26 418273f6 41833ef8
7fffffff 418273f2 41867028 4003c9a2 4180ac6c 00000004 41833f8c 4013e71c
40279e1c 40279e26 40226c16 4013ced2 40279e26 40279e58 4028d040 00000000
Call Trace:
[<40025534>] 0x40025534
[<4004e514>] 0x4004e514
[<400255de>] 0x400255de
[<40159e20>] 0x40159e20
[<40159e20>] 0x40159e20
It is not fatal, the driver and the system continue to function normally.
As per the warning the coherent_dma_mask is not set on this device.
There is nothing special about the DMA memory coherency on this hardware
so we can just set the mask to 32bits in the platform data for the FEC
ethernet devices.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This code works fine. The comment is misleading so remove it.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
According to Apple's Developer Notes, all of the early PowerBook models
have their RTC connected to VIA1. Use the VIA clock ops as appropriate.
This was tested on a PowerBook 170.
Don't use the VIA ops when not appropriate. Calling unimplemented clock
or PRAM getter or setter ops can now result in an error instead of
failing silently.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The PMU watchdog will power down the system if the kernel is slow
to start up, e.g. due to unpacking a large initrd. The powerpc
version of this driver (via-pmu.c) has a solution for the same
problem. It uses this call sequence:
setup_arch
find_via_pmu
init_pmu
...
arch_initcall
via_pmu_start
Bring via-pmu68k.c into line with via-pmu.c to fix this issue.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The algorithm used in baboon_irq() appears to be subject to a race
condition: an IRQ flag could be lost if asserted between the MOV
instructions from and to the interrupt flag register. However,
testing shows that the write to the flag register has no effect.
Rewrite this loop to remove the apparent race condition.
No-one seems to know how to clear Baboon IRQ flags, or whether
that's even possible, so add a comment about this.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Stan's tests showed that PDMA improves sequential read performance by
a factor of 5 on a PowerBook 190. Last time I tried this on a
PowerBook 520 it didn't work, so let's not enable it there until
it can be tested with the present mac_scsi driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Apparently these Dayna cards don't have a pseudoslot declaration ROM
which means they can't be probed like NuBus cards.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at functions with large stack frames across all architectures
led me discovering that BUG() suffers from the same problem as
fortify_panic(), which I've added a workaround for already.
In short, variables that go out of scope by calling a noreturn function
or __builtin_unreachable() keep using stack space in functions
afterwards.
A workaround that was identified is to insert an empty assembler
statement just before calling the function that doesn't return. I'm
adding a macro "barrier_before_unreachable()" to document this, and
insert calls to that in all instances of BUG() that currently suffer
from this problem.
The files that saw the largest change from this had these frame sizes
before, and much less with my patch:
fs/ext4/inode.c:82:1: warning: the frame size of 1672 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/namei.c:434:1: warning: the frame size of 904 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/super.c:2279:1: warning: the frame size of 1160 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/xattr.c:146:1: warning: the frame size of 1168 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/f2fs/inode.c:152:1: warning: the frame size of 1424 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:1195:1: warning: the frame size of 1068 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:395:1: warning: the frame size of 1084 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:298:1: warning: the frame size of 928 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:418:1: warning: the frame size of 908 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_lblcr.c:718:1: warning: the frame size of 960 bytes is larger than 800 bytes [-Wframe-larger-than=]
drivers/net/xen-netback/netback.c:1500:1: warning: the frame size of 1088 bytes is larger than 800 bytes [-Wframe-larger-than=]
In case of ARC and CRIS, it turns out that the BUG() implementation
actually does return (or at least the compiler thinks it does),
resulting in lots of warnings about uninitialized variable use and
leaving noreturn functions, such as:
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:3804:1: error: control reaches end of non-void function [-Werror=return-type]
include/linux/dmaengine.h: In function 'dma_maxpq':
include/linux/dmaengine.h:1123:1: error: control reaches end of non-void function [-Werror=return-type]
This makes them call __builtin_trap() instead, which should normally
dump the stack and kill the current process, like some of the other
architectures already do.
I tried adding barrier_before_unreachable() to panic() and
fortify_panic() as well, but that had very little effect, so I'm not
submitting that patch.
Vineet said:
: For ARC, it is double win.
:
: 1. Fixes 3 -Wreturn-type warnings
:
: | ../net/core/ethtool.c:311:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../kernel/sched/core.c:3246:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../include/linux/sunrpc/svc_xprt.h:180:1: warning: control reaches end of
: non-void function [-Wreturn-type]
:
: 2. bloat-o-meter reports code size improvements as gcc elides the
: generated code for stack return.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365
Link: http://lkml.kernel.org/r/20171219114112.939391-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Tested-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
except, again, POLLFREE and POLL_BUSY_LOOP.
With this, we finally get to the promised end result:
- POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
stray instances of ->poll() still using those will be caught by
sparse.
- eventpoll.c and select.c warning-free wrt __poll_t
- no more kernel-side definitions of POLL... - userland ones are
visible through the entire kernel (and used pretty much only for
mangle/demangle)
- same behavior as after the first series (i.e. sparc et.al. epoll(2)
working correctly).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
to the clk rate protection support added by Jerome Brunet. This feature
will allow consumers to lock in a certain rate on the output of a clk so
that things like audio playback don't hear pops when the clk frequency
changes due to shared parent clks changing rates. Currently the clk
API doesn't guarantee the rate of a clk stays at the rate you request
after clk_set_rate() is called, so this new API will allow drivers
to express that requirement. Beyond this, the core got some debugfs
pretty printing patches and a couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h file
causes small one-liners in all the architecture Kbuild files. Overall, the
driver diff seems to be the normal stuff that comes all the time to
fix little problems here and there and to support new hardware.
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bGPp
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
This pull requests contains a consolidation of the generic no-IOMMU code,
a well as the glue code for swiotlb. All the code is based on the x86
implementation with hooks to allow all architectures that aren't cache
coherent to use it. The x86 conversion itself has been deferred because
the x86 maintainers were a little busy in the last months.
-----BEGIN PGP SIGNATURE-----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=Nrl9
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping updates from Christoph Hellwig:
"Except for a runtime warning fix from Christian this is all about
consolidation of the generic no-IOMMU code, a well as the glue code
for swiotlb.
All the code is based on the x86 implementation with hooks to allow
all architectures that aren't cache coherent to use it.
The x86 conversion itself has been deferred because the x86
maintainers were a little busy in the last months"
* tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping: (57 commits)
MAINTAINERS: add the iommu list for swiotlb and xen-swiotlb
arm64: use swiotlb_alloc and swiotlb_free
arm64: replace ZONE_DMA with ZONE_DMA32
mips: use swiotlb_{alloc,free}
mips/netlogic: remove swiotlb support
tile: use generic swiotlb_ops
tile: replace ZONE_DMA with ZONE_DMA32
unicore32: use generic swiotlb_ops
ia64: remove an ifdef around the content of pci-dma.c
ia64: clean up swiotlb support
ia64: use generic swiotlb_ops
ia64: replace ZONE_DMA with ZONE_DMA32
swiotlb: remove various exports
swiotlb: refactor coherent buffer allocation
swiotlb: refactor coherent buffer freeing
swiotlb: wire up ->dma_supported in swiotlb_dma_ops
swiotlb: add common swiotlb_map_ops
swiotlb: rename swiotlb_free to swiotlb_exit
x86: rename swiotlb_dma_ops
powerpc: rename swiotlb_dma_ops
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull siginfo cleanups from Eric Biederman:
"Long ago when 2.4 was just a testing release copy_siginfo_to_user was
made to copy individual fields to userspace, possibly for efficiency
and to ensure initialized values were not copied to userspace.
Unfortunately the design was complex, it's assumptions unstated, and
humans are fallible and so while it worked much of the time that
design failed to ensure unitialized memory is not copied to userspace.
This set of changes is part of a new design to clean up siginfo and
simplify things, and hopefully make the siginfo handling robust enough
that a simple inspection of the code can be made to ensure we don't
copy any unitializied fields to userspace.
The design is to unify struct siginfo and struct compat_siginfo into a
single definition that is shared between all architectures so that
anyone adding to the set of information shared with struct siginfo can
see the whole picture. Hopefully ensuring all future si_code
assignments are arch independent.
The design is to unify copy_siginfo_to_user32 and
copy_siginfo_from_user32 so that those function are complete and cope
with all of the different cases documented in signinfo_layout. I don't
think there was a single implementation of either of those functions
that was complete and correct before my changes unified them.
The design is to introduce a series of helpers including
force_siginfo_fault that take the values that are needed in struct
siginfo and build the siginfo structure for their callers. Ensuring
struct siginfo is built correctly.
The remaining work for 4.17 (unless someone thinks it is post -rc1
material) is to push usage of those helpers down into the
architectures so that architecture specific code will not need to deal
with the fiddly work of intializing struct siginfo, and then when
struct siginfo is guaranteed to be fully initialized change copy
siginfo_to_user into a simple wrapper around copy_to_user.
Further there is work in progress on the issues that have been
documented requires arch specific knowledge to sort out.
The changes below fix or at least document all of the issues that have
been found with siginfo generation. Then proceed to unify struct
siginfo the 32 bit helpers that copy siginfo to and from userspace,
and generally clean up anything that is not arch specific with regards
to siginfo generation.
It is a lot but with the unification you can of siginfo you can
already see the code reduction in the kernel"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (45 commits)
signal/memory-failure: Use force_sig_mceerr and send_sig_mceerr
mm/memory_failure: Remove unused trapno from memory_failure
signal/ptrace: Add force_sig_ptrace_errno_trap and use it where needed
signal/powerpc: Remove unnecessary signal_code parameter of do_send_trap
signal: Helpers for faults with specialized siginfo layouts
signal: Add send_sig_fault and force_sig_fault
signal: Replace memset(info,...) with clear_siginfo for clarity
signal: Don't use structure initializers for struct siginfo
signal/arm64: Better isolate the COMPAT_TASK portion of ptrace_hbptriggered
ptrace: Use copy_siginfo in setsiginfo and getsiginfo
signal: Unify and correct copy_siginfo_to_user32
signal: Remove the code to clear siginfo before calling copy_siginfo_from_user32
signal: Unify and correct copy_siginfo_from_user32
signal/blackfin: Remove pointless UID16_SIGINFO_COMPAT_NEEDED
signal/blackfin: Move the blackfin specific si_codes to asm-generic/siginfo.h
signal/tile: Move the tile specific si_codes to asm-generic/siginfo.h
signal/frv: Move the frv specific si_codes to asm-generic/siginfo.h
signal/ia64: Move the ia64 specific si_codes to asm-generic/siginfo.h
signal/powerpc: Remove redefinition of NSIGTRAP on powerpc
signal: Move addr_lsb into the _sigfault union for clarity
...
- First part of an overhaul of the NuBus subsystem, to bring it up to
modern driver model standards,
- A race condition fix for Mac,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PZNx
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- first part of an overhaul of the NuBus subsystem, to bring it up to
modern driver model standards
- a race condition fix for Mac
- defconfig updates
* tag 'm68k-for-v4.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
MAINTAINERS: Add NuBus subsystem entry
m68k/mac: Fix race conditions in OSS interrupt dispatch
nubus: Add support for the driver model
nubus: Add expansion_type values for various Mac models
nubus: Adopt standard linked list implementation
nubus: Rename struct nubus_dev
nubus: Rework /proc/bus/nubus/s/ implementation
nubus: Generalize block resource handling
nubus: Clean up whitespace
nubus: Remove redundant code
nubus: Call proc_mkdir() not more than once per slot directory
nubus: Validate slot resource IDs
nubus: Fix log spam
nubus: Use static functions where possible
nubus: Fix up header split
nubus: Avoid array underflow and overflow
m68k/defconfig: Update defconfigs for v4.15-rc1
It doesn't actually do anything. Merge its help text into
EXTRA_FIRMWARE.
Fixes: 5620a0d1aa ("firmware: delete in-kernel firmware")
Fixes: 0946b2fb38 ("firmware: cleanup FIRMWARE_IN_KERNEL message")
Signed-off-by: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The siginfo structure has all manners of holes with the result that a
structure initializer is not guaranteed to initialize all of the bits.
As we have to copy the structure to userspace don't even try to use
a structure initializer. Instead use clear_siginfo followed by initializing
selected fields. This gives a guarantee that uninitialized kernel memory
is not copied to userspace.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The interrupt dispatch algorithm used in the OSS driver seems to be
subject to race conditions: an IRQ flag could be lost if asserted between
the MOV instructions from and to the interrupt flag register. But testing
shows that the write to the flag register has no effect, so rewrite the
algorithm without the theoretical race condition.
There is a second theoretical race condition here. When oss_irq() is
called with say, IPL == 2 it will invoke the SCSI interrupt handler.
The SCSI IRQ is then cleared by the mac_scsi driver. If SCSI and NuBus
IRQs are now asserted together, oss_irq() will be invoked with IPL == 3
and the mac_scsi interrupt handler can be re-entered. This re-entrance
issue is not limited to SCSI and could affect NuBus and ADB drivers too.
Fix it by splitting up oss_irq() into separate handlers for each IPL.
No-one seems to know how OSS irq flags can be cleared, if at all, so add
a comment to this effect (actually reinstate one I previously removed).
Testing showed that a slot IRQ with no handler can remain asserted (in
this case a Radius video card) without causing problems for other IRQs.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add an expansion slot attribute to allow drivers to properly handle
cards like Comm Slot cards and PDS cards without declaration ROMs.
This clarifies the logic for the Centris 610 model which has no
Comm Slot but has an optional on-board SONIC device.
Cc: "David S. Miller" <davem@davemloft.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Lift the code from x86 so that we behave consistently. In the future we
should probably warn if any of these is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Construct the init thread stack in the linker script rather than doing it
by means of a union so that ia64's init_task.c can be got rid of.
The following symbols are then made available from INIT_TASK_DATA() linker
script macro:
init_thread_union
init_stack
INIT_TASK_DATA() also expands the region to THREAD_SIZE to accommodate the
size of the init stack. init_thread_union is given its own section so that
it can be placed into the stack space in the right order. I'm assuming
that the ia64 ordering is correct and that the task_struct is first and the
thread_info second.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Will Deacon <will.deacon@arm.com> (arm64)
Tested-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Now that every architecture is using the generic clkdev.h file
and we no longer include asm/clkdev.h anywhere in the tree, we
can remove it.
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
Commit 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT
program type") introduced the bpf_perf_event_data structure which
exports the pt_regs structure. This is OK for multiple architectures
but fail for s390 and arm64 which do not export pt_regs. Programs
using them, for example, the bpf selftest fail to compile on these
architectures.
For s390, exporting the pt_regs is not an option because s390 wants
to allow changes to it. For arm64, there is a user_pt_regs structure
that covers parts of the pt_regs structure for use by user space.
To solve the broken uapi for s390 and arm64, introduce an abstract
type for pt_regs and add an asm/bpf_perf_event.h file that concretes
the type. An asm-generic header file covers the architectures that
export pt_regs today.
The arch-specific enablement for s390 and arm64 follows in separate
commits.
Reported-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Fixes: 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT program type")
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-and-tested-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit be7635e728 ("arch, ftrace: for KASAN put hard/soft IRQ entries
into separate sections") added a new linker section, SOFTIRQENTRY_TEXT,
to the linker scripts for most architectures. It didn't add it to any of
the linker scripts for the m68k architecture. This was not really a problem
because it is only defined if either of CONFIG_FUNCTION_GRAPH_TRACER or
CONFIG_KASAN are enabled - which can never be true for m68k.
However commit 229a718605 ("irq: Make the irqentry text section
unconditional") means that SOFTIRQENTRY_TEXT is now always defined. So on
m68k we now end up with a separate ELF section for .softirqentry.text
instead of it being part of the .text section. On some m68k targets in some
configurations this can also cause a fatal link error:
LD vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: section .softirqentry.text loaded at [0000000010de10c0,0000000010de12dd] overlaps section .rodata loaded at [0000000010de10c0,0000000010e0fd67]
To fix add in the missing SOFTIRQENTRY_TEXT section into the m68k linker
scripts. I noticed that m68k is also missing the IRQENTRY_TEXT section,
so this patch also adds an entry for that too.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This fixes a missed function prototype callback from the timer conversions.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20171123221902.GA75727@beast
This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".
Done using the following semantic patch:
@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@
DEFINE_TIMER(_timer, _callback);
@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@
void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
{ ... }
Signed-off-by: Kees Cook <keescook@chromium.org>
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture
doesn't support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=ALJf
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture doesn't
support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
* tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: turn dma_cache_sync into a dma_map_ops method
sh: make dma_cache_sync a no-op
xtensa: make dma_cache_sync a no-op
unicore32: make dma_cache_sync a no-op
powerpc: make dma_cache_sync a no-op
mn10300: make dma_cache_sync a no-op
microblaze: make dma_cache_sync a no-op
ia64: make dma_cache_sync a no-op
frv: make dma_cache_sync a no-op
x86: make dma_cache_sync a no-op
floppy: consolidate the dummy fd_cacheflush definition
drivers: flag buses which demand DMA configuration
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
- More printk modernization,
- Various cleanups and fixes (incl. a race condition) for Mac,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cuxe
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- more printk modernization
- various cleanups and fixes (incl. a race condition) for Mac
- defconfig updates
* tag 'm68k-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.14-rc7
m68k/mac: Add mutual exclusion for IOP interrupt polling
m68k/mac: Disentangle VIA/RBV and NuBus initialization
m68k/mac: Disentangle VIA and OSS initialization
m68k/mac: More printk modernization
The IOP interrupt handler iop_ism_irq() is used by the adb-iop
driver to poll for ADB request completion. Unfortunately, it is not
re-entrant. Fix the race condition by adding an iop_ism_irq_poll()
function with suitable mutual exclusion.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The Nubus subsystem should not be concerned with differences between VIA,
RBV and OSS platforms. It should be portable across Macs and PowerMacs.
This goal has implications for the initialization code relating to bus
locking and slot interrupts.
During Nubus initialization, bus transactions are "unlocked": on VIA2 and
RBV machines, via_nubus_init() sets a bit in the via2[gBufB] register to
allow bus-mastering Nubus cards to arbitrate for the bus. This happens
upon subsys_initcall(nubus_init). But because nubus_init() has no effect
on card state, this sequence is arbitrary.
Moreover, when Penguin is used to boot Linux, the bus is already unlocked
when Linux starts. On OSS machines there's no attempt to unlock Nubus
transactions at all. (Maybe there's no benefit on that platform or maybe
no-one knows how.)
All of this demonstrates that there's no benefit in locking out
bus-mastering cards, as yet. (If the need arises, we could lock the bus
for the duration of a timing-critical operation.) NetBSD unlocks the
Nubus early (at VIA initialization) and we can do the same.
via_nubus_init() is also responsible for some VIA interrupt setup that
should happen earlier than subsys_initcall(nubus_init). And actually, the
Nubus subsystem need not be involved with slot interrupts: SLOT2IRQ
works fine because Nubus slot IRQs are geographically assigned
(regardless of platform).
For certain platforms with PDS slots, some Nubus IRQs may be platform
IRQs and this is not something that the NuBus subsystem should worry
about. So let's invoke via_nubus_init() earlier and make the platform
responsible for bus unlocking and interrupt setup instead of the NuBus
subsystem.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
macintosh_config->via_type is meaningless on Mac IIfx (i.e. the only
model with OSS chip), so skip the via_type switch statement.
Call oss_init() before via_init() because it is more important and
because that is the right place to initialize the oss_present flag.
On this model, bringing forward oss_init() and delaying via_init()
is no problem because those functions are independent.
The only requirement here is that oss_register_interrupts() happens
after via_init(). That is, mac_init_IRQ() happens after config_mac().
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Log message fragments used to be printed on one line but now get split up.
Fix this. Also, suppress log spam that merely prints known pointer values.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add support for Sysam stmark2 board, an open hardware embedded
Linux board, see http://sysam.it/cff_stmark2.html for any info.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This patch adds initial module base address and irq for dspi0.
It also defines the dspi0 clock to be used by the Freescale driver.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
It is possible to select INPUT_M68K_BEEP in a nommu configuration. This
results in the following link error:
drivers/input/misc/m68kspkr.o: In function `m68kspkr_event':
m68kspkr.c:(.text+0x3a): undefined reference to `mach_beep'
m68kspkr.c:(.text+0x5e): undefined reference to `mach_beep'
m68kspkr.c:(.text+0x78): undefined reference to `mach_beep'
drivers/input/misc/m68kspkr.o: In function `m68kspkr_init':
m68kspkr.c:(.init.text+0x4): undefined reference to `mach_beep'
Pull the mach_beep definition in setup.c to avoid it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The Freescale ColdFire M5441x system-on-chip parts have full paged MMU
hardware support. So far though we have only allowed them to be
configured for use in non-MMU mode.
All required kernel changes to support operation of the M5441x parts
with MMU enabled have been pushed into the kernel, so now we can allow
it to be configured and used with the MMU enabled.
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The m68k pg_data_table is a fix size array defined in arch/m68k/mm/init.c.
Index numbers within it are defined based on memory size. But for Coldfire
these don't take into account a non-zero physical RAM base address, and this
causes us to access past the end of this array at system start time.
Change the node shift calculation so that we keep the index inside its range.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The M54[78]x ColdFire parts are not the only members of the ColdFire family
that have an MMU. But currently some of the early MMU initialization code
is inside the startup code specific to only the ColdFire M54[78]x parts.
Move that early ColdFire MMU init code so that it is run for other ColdFire
parts running with MMU enabled.
Specifically this means that the MMU initialization code will now also be
run for the ColdFire M5441x parts when running with MMU enabled.
The code move meant that the extern definition for the mmu_context_init()
function had to be moved as well. To make it clear that is ColdFire specific
I have renamed that with a "cf_" in front of it and put its extern definition
in the mcfmmu.h (which is already included by the setup code).
Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After we removed all the dead wood it turns out only two architectures
actually implement dma_cache_sync as a real op: mips and parisc. Add
a cache_sync method to struct dma_map_ops and implement it for the
mips defualt DMA ops, and the parisc pa11 ops.
Note that arm, arc and openrisc support DMA_ATTR_NON_CONSISTENT, but
never provided a functional dma_cache_sync implementations, which
seems somewhat odd.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Pull m68knommu updates from Greg Ungerer:
"Only two changes. One removes unused code, the other makes local clock
code arguments consistent with generic clock code"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: remove dead code
m68k: allow NULL clock for clk_get_rate
With gcc 4.1.2:
include/linux/swapops.h: In function ‘swp_entry_to_pmd’:
include/linux/swapops.h:294: warning: missing braces around initializer
include/linux/swapops.h:294: warning: (near initialization for ‘(anonymous).pmd’)
Due to a GCC zero initializer bug (#53119), the standard "(pmd_t){ 0 }"
initializer is not accepted by all GCC versions.
In addition, on m68k pmd_t is an array instead of a single value, so we
need "(pmd_t){ { 0 }, }" instead of "(pmd_t){ 0 }".
Based on commit 9157259d16 ("mm: add pmd_t initializer __pmd() to
work around a GCC bug.") for sparc32.
Fixes: 616b837153 ("mm: thp: enable thp migration in generic path")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge more updates from Andrew Morton:
- most of the rest of MM
- a small number of misc things
- lib/ updates
- checkpatch
- autofs updates
- ipc/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (126 commits)
ipc: optimize semget/shmget/msgget for lots of keys
ipc/sem: play nicer with large nsops allocations
ipc/sem: drop sem_checkid helper
ipc: convert kern_ipc_perm.refcount from atomic_t to refcount_t
ipc: convert sem_undo_list.refcnt from atomic_t to refcount_t
ipc: convert ipc_namespace.count from atomic_t to refcount_t
kcov: support compat processes
sh: defconfig: cleanup from old Kconfig options
mn10300: defconfig: cleanup from old Kconfig options
m32r: defconfig: cleanup from old Kconfig options
drivers/pps: use surrounding "if PPS" to remove numerous dependency checks
drivers/pps: aesthetic tweaks to PPS-related content
cpumask: make cpumask_next() out-of-line
kmod: move #ifdef CONFIG_MODULES wrapper to Makefile
kmod: split off umh headers into its own file
MAINTAINERS: clarify kmod is just a kernel module loader
kmod: split out umh code into its own file
test_kmod: flip INT checks to be consistent
test_kmod: remove paranoid UINT_MAX check on uint range processing
vfat: deduplicate hex2bin()
...
Patch series "Define CPU_BIG_ENDIAN or warn for inconsistencies", v3.
While working on enabling queued rwlock on SPARC, found this following
code in include/asm-generic/qrwlock.h which uses CONFIG_CPU_BIG_ENDIAN to
clear a byte.
static inline u8 *__qrwlock_write_byte(struct qrwlock *lock)
{
return (u8 *)lock + 3 * IS_BUILTIN(CONFIG_CPU_BIG_ENDIAN);
}
Problem is many of the fixed big endian architectures don't define
CPU_BIG_ENDIAN and clears the wrong byte.
Define CPU_BIG_ENDIAN for all the fixed big endian architecture to fix it.
Also found few more references of this config parameter in
drivers/of/base.c
drivers/of/fdt.c
drivers/tty/serial/earlycon.c
drivers/tty/serial/serial_core.c
Be aware that this may cause regressions if someone has worked-around
problems in the above code already. Remove the work-around.
Here is our original discussion
https://lkml.org/lkml/2017/5/24/620
Link: http://lkml.kernel.org/r/1499358861-179979-2-git-send-email-babu.moger@oracle.com
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Stafford Horne <shorne@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
- Restore symbol versions for symbols exported from assembly,
- Defconfig updates,
- Mac fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/iJN
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- restore symbol versions for symbols exported from assembly
- defconfig updates
- Mac fixes
* tag 'm68k-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/mac: Avoid soft-lockup warning after mach_power_off
m68k/mac: Don't hang waiting for Cuda power-down command
m68k: Restore symbol versions for symbols exported from assembly
m68k/defconfig: Update defconfigs for v4.13-rc1
As CONFIG_RTC_DRV_M5441x doesn't exist because the driver never made it
upstream, there is no device to register. Remove code that is never
compiled and init_BSP() as it doesn't do anything.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: facdf0ed4f ("m68knommu: introduce basic clk infrastructure")
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-kernel@vger.kernel.org
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Disable interrupts for power-off, like other platforms do. This prevents
meaningless warnings from the soft-lockup detector on models with a power
supply unit not under software control.
Reported-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Testing shows that the CUDA_POWERDOWN command never completes (for a
Centris 660av or LC 475, at least). So, don't wait for command completion
on those Cuda-based models that do not support soft power. Just proceed to
log the usual message, "It is now safe to turn off your Macintosh."
Reported-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
WARNING: EXPORT symbol "__divsi3" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "__umodsi3" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "__mulsi3" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "__modsi3" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "__udivsi3" [vmlinux] version generation failed, symbol will not be versioned.
Add <asm/asm-prototypes.h> so that genksyms knows the types of these
symbols and can generate CRCs for them.
Fixes: d13ffb5630 ("m68k: move exports to definitions"
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[geert: Add warning messages, match actual prototypes in gccint.info]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The pci_fixup_irqs() function allocates IRQs for all PCI devices present in
a system; those PCI devices possibly belong to different PCI bus trees (and
possibly rooted at different host bridges) and may well be enabled (ie
probed and bound to a driver) by the time pci_fixup_irqs() is called when
probing a given host bridge driver.
Furthermore, current kernel code relying on pci_fixup_irqs() to assign
legacy PCI IRQs to devices does not work at all for hotplugged devices in
that the code carrying out the IRQ fixup is called at host bridge driver
probe time, which just cannot take into account devices hotplugged after
the system has booted.
The introduction of map/swizzle function hooks in struct pci_host_bridge
allows us to define per-bridge map/swizzle functions that can be used at
device probe time in PCI core code to allocate IRQs for a given device
(through pci_assign_irq()).
Convert PCI host bridge initialization code to the
pci_scan_root_bus_bridge() API (that allows to pass a struct
pci_host_bridge with initialized map/swizzle pointers) and remove the
pci_fixup_irqs() call from arch code.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Several variables had their types changed from unsigned long to u32, but
the arch-specific implementations of flat_set_persistent() weren't
updated, leading to compiler warnings on blackfin and m68k:
fs/binfmt_flat.c: In function ‘load_flat_file’:
fs/binfmt_flat.c:799: warning: passing argument 2 of ‘flat_set_persistent’ from incompatible pointer type
Fixes: 468138d785 ("binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull uacess-unaligned removal from Al Viro:
"That stuff had just one user, and an exotic one, at that - binfmt_flat
on arm and m68k"
* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill {__,}{get,put}_user_unaligned()
binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail
- Move generic-y of exported headers to uapi/asm/Kbuild
for complete de-coupling of UAPI
- Clean up scripts/Makefile.headersinst
- Fix host programs for 32 bit machine with XFS file system
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Sw8W
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Move generic-y of exported headers to uapi/asm/Kbuild for complete
de-coupling of UAPI
- Clean up scripts/Makefile.headersinst
- Fix host programs for 32 bit machine with XFS file system
* tag 'kbuild-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (29 commits)
kbuild: Enable Large File Support for hostprogs
kbuild: remove wrapper files handling from Makefile.headersinst
kbuild: split exported generic header creation into uapi-asm-generic
kbuild: do not include old-kbuild-file from Makefile.headersinst
xtensa: move generic-y of exported headers to uapi/asm/Kbuild
unicore32: move generic-y of exported headers to uapi/asm/Kbuild
tile: move generic-y of exported headers to uapi/asm/Kbuild
sparc: move generic-y of exported headers to uapi/asm/Kbuild
sh: move generic-y of exported headers to uapi/asm/Kbuild
parisc: move generic-y of exported headers to uapi/asm/Kbuild
openrisc: move generic-y of exported headers to uapi/asm/Kbuild
nios2: move generic-y of exported headers to uapi/asm/Kbuild
nios2: remove unneeded arch/nios2/include/(generated/)asm/signal.h
microblaze: move generic-y of exported headers to uapi/asm/Kbuild
metag: move generic-y of exported headers to uapi/asm/Kbuild
m68k: move generic-y of exported headers to uapi/asm/Kbuild
m32r: move generic-y of exported headers to uapi/asm/Kbuild
ia64: remove redundant generic-y += kvm_para.h from asm/Kbuild
hexagon: move generic-y of exported headers to uapi/asm/Kbuild
h8300: move generic-y of exported headers to uapi/asm/Kbuild
...
Make the code like the rest of the kernel.
Link: http://lkml.kernel.org/r/14db9c166d5b68efa77e337cfe49bb9b29bca3f7.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86nommu update from Greg Ungerer:
"Only a single change, to remove old Kconfig options from defconfigs"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: defconfig: Cleanup from old Kconfig options
Since commit fcc8487d47 ("uapi: export all headers under uapi
directories"), all (and only) headers under uapi directories are
exported, but asm-generic wrappers are still exceptions.
To complete de-coupling the uapi from kernel headers, move generic-y
of exported headers to uapi/asm/Kbuild.
With this change, "make headers_install" will just need to parse
uapi/asm/Kbuild to build up exported headers.
For m68k, "generic-y += termios.h" is doubled in asm/Kbuild and
uapi/asm/Kbuild. So, the one in the former can be simply removed.
Also, move "generic-y += kprobes.h" up in order to keep the entries
sorted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Pull user access str* updates from Al Viro:
"uaccess str...() dead code removal"
* 'uaccess.strlen' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
s390 keyboard.c: don't open-code strndup_user()
mips: get rid of unused __strnlen_user()
get rid of unused __strncpy_from_user() instances
kill strlen_user()
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls
to ->mapping_error so that the dma_map_ops instances are
more self contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)
-----BEGIN PGP SIGNATURE-----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=0Fso
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
Pull timer updates from Thomas Gleixner:
"A rather large update for timers/timekeeping:
- compat syscall consolidation (Al Viro)
- Posix timer consolidation (Christoph Helwig / Thomas Gleixner)
- Cleanup of the device tree based initialization for clockevents and
clocksources (Daniel Lezcano)
- Consolidation of the FTTMR010 clocksource/event driver (Linus
Walleij)
- The usual set of small fixes and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (93 commits)
timers: Make the cpu base lock raw
clocksource/drivers/mips-gic-timer: Fix an error code in 'gic_clocksource_of_init()'
clocksource/drivers/fsl_ftm_timer: Unmap region obtained by of_iomap
clocksource/drivers/tcb_clksrc: Make IO endian agnostic
clocksource/drivers/sun4i: Switch to the timer-of common init
clocksource/drivers/timer-of: Fix invalid iomap check
Revert "ktime: Simplify ktime_compare implementation"
clocksource/drivers: Fix uninitialized variable use in timer_of_init
kselftests: timers: Add test for frequency step
kselftests: timers: Fix inconsistency-check to not ignore first timestamp
time: Add warning about imminent deprecation of CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Clean up CLOCK_MONOTONIC_RAW time handling
posix-cpu-timers: Make timespec to nsec conversion safe
itimer: Make timeval to nsec conversion range limited
timers: Fix parameter description of try_to_del_timer_sync()
ktime: Simplify ktime_compare implementation
clocksource/drivers/fttmr010: Factor out clock read code
clocksource/drivers/fttmr010: Implement delay timer
clocksource/drivers: Add timer-of common init routine
clocksource/drivers/tcb_clksrc: Save timer context on suspend/resume
...
on MMU targets EFAULT is possible here. Make both return 0 or error,
passing what used to be the return value of flat_get_addr_from_rp()
by reference.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently, internals of dma_common_mmap() is compiled out if build is
done for either NOMMU or target which explicitly says it does not
have/want coherent DMA mmap. It turned out that dma_common_mmap() can
be handy in NOMMU setup (at least for ARM).
This patch converts exitent NOMMU targets to use ARCH_NO_COHERENT_DMA_MMAP,
thus when CONFIG_MMU is gone from dma_common_mmap() their behaviour stays
unchanged.
ARM is not converted to ARCH_NO_COHERENT_DMA_MMAP because it 1)
already has mmap callback which can handle (at some extent) NOMMU 2)
already defines dummy pgprot_noncached() for NOMMU build.
c6x and frv stay untouched since they already have ARCH_NO_COHERENT_DMA_MMAP.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
The only user of thread_saved_pc() in non-arch-specific code was removed
in commit 8243d55977 ("sched/core: Remove pointless printout in
sched_show_task()"). Remove the implementations as well.
Some architectures use thread_saved_pc() in their arch-specific code.
Leave their thread_saved_pc() intact.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove old, dead Kconfig option INET_LRO. It is gone since
commit 7bbf3cae65 ("ipv4: Remove inet_lro library").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This fixes debugger syscall restart interactions. A debugger that
modifies the tracee's program counter is expected to set the orig_d0
pseudo register to -1, to disable a possible syscall restart.
This removes the last user of the ptrace_signal_deliver hook in the ptrace
signal handling, so remove that as well.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
By moving the kernel side __SI_* defintions right next to the userspace
ones we can kill the non-uapi versions of <asm/siginfo.h> include
include/asm-generic/siginfo.h and untangle the unholy mess of includes.
[ tglx: Removed uapi/asm/siginfo.h from m32r, microblaze, mn10300 and score ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-ia64@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: sparclinux@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20170603190102.28866-6-hch@lst.de
Regularly, when a new header is created in include/uapi/, the developer
forgets to add it in the corresponding Kbuild file. This error is usually
detected after the release is out.
In fact, all headers under uapi directories should be exported, thus it's
useless to have an exhaustive list.
After this patch, the following files, which were not exported, are now
exported (with make headers_install_all):
asm-arc/kvm_para.h
asm-arc/ucontext.h
asm-blackfin/shmparam.h
asm-blackfin/ucontext.h
asm-c6x/shmparam.h
asm-c6x/ucontext.h
asm-cris/kvm_para.h
asm-h8300/shmparam.h
asm-h8300/ucontext.h
asm-hexagon/shmparam.h
asm-m32r/kvm_para.h
asm-m68k/kvm_para.h
asm-m68k/shmparam.h
asm-metag/kvm_para.h
asm-metag/shmparam.h
asm-metag/ucontext.h
asm-mips/hwcap.h
asm-mips/reg.h
asm-mips/ucontext.h
asm-nios2/kvm_para.h
asm-nios2/ucontext.h
asm-openrisc/shmparam.h
asm-parisc/kvm_para.h
asm-powerpc/perf_regs.h
asm-sh/kvm_para.h
asm-sh/ucontext.h
asm-tile/shmparam.h
asm-unicore32/shmparam.h
asm-unicore32/ucontext.h
asm-x86/hwcap2.h
asm-xtensa/kvm_para.h
drm/armada_drm.h
drm/etnaviv_drm.h
drm/vgem_drm.h
linux/aspeed-lpc-ctrl.h
linux/auto_dev-ioctl.h
linux/bcache.h
linux/btrfs_tree.h
linux/can/vxcan.h
linux/cifs/cifs_mount.h
linux/coresight-stm.h
linux/cryptouser.h
linux/fsmap.h
linux/genwqe/genwqe_card.h
linux/hash_info.h
linux/kcm.h
linux/kcov.h
linux/kfd_ioctl.h
linux/lightnvm.h
linux/module.h
linux/nbd-netlink.h
linux/nilfs2_api.h
linux/nilfs2_ondisk.h
linux/nsfs.h
linux/pr.h
linux/qrtr.h
linux/rpmsg.h
linux/sched/types.h
linux/sed-opal.h
linux/smc.h
linux/smc_diag.h
linux/stm.h
linux/switchtec_ioctl.h
linux/vfio_ccw.h
linux/wil6210_uapi.h
rdma/bnxt_re-abi.h
Note that I have removed from this list the files which are generated in every
exported directories (like .install or .install.cmd).
Thanks to Julien Floret <julien.floret@6wind.com> for the tip to get all
subdirs with a pure makefile command.
For the record, note that exported files for asm directories are a mix of
files listed by:
- include/uapi/asm-generic/Kbuild.asm;
- arch/<arch>/include/uapi/asm/Kbuild;
- arch/<arch>/include/asm/Kbuild.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Salter <msalter@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
The alloc/free metaphor used for IOP messages is misleading and can
cause mistakes like the pointless msg2 temporary variable. Use a more
meaningful name to help simplify the code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
These changes save 1014 bytes according to scripts/bloat-o-meter.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the m68k arch's coldfire clockevent driver initialize these fields
properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
mm/filemap.c: In function ‘clear_bit_unlock_is_negative_byte’:
mm/filemap.c:933: warning: passing argument 2 of ‘test_bit’ discards qualifiers from pointer target type
Make the bitmask pointed to by the "vaddr" parameter volatile to fix
this, like is done on other architectures.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Update code that relied on sched.h including various MM types for them.
This will allow us to remove the <linux/mm_types.h> include from <linux/sched.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/debug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/debug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/mm.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/mm.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
The APIs that are going to be moved first are:
mm_alloc()
__mmdrop()
mmdrop()
mmdrop_async_fn()
mmdrop_async()
mmget_not_zero()
mmput()
mmput_async()
get_task_mm()
mm_access()
mm_release()
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/loadavg.h> out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.
Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull m68nommu update from Greg Ungerer:
"Only a single change, to update the amcore board defconfig"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k/defconfig: amcore board defconfig tuning
Fix typos and add the following to the scripts/spelling.txt:
efective||effective
While we are here, fix the "addres" as well in the touched line in
arch/openrisc/kernel/entry.S.
Link: http://lkml.kernel.org/r/1481573103-11329-10-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Often all is needed is these small helpers, instead of compiler.h or a
full kprobes.h. This is important for asm helpers, in fact even some
asm/kprobes.h make use of these helpers... instead just keep a generic
asm file with helpers useful for asm code with the least amount of
clutter as possible.
Likewise we need now to also address what to do about this file for both
when architectures have CONFIG_HAVE_KPROBES, and when they do not. Then
for when architectures have CONFIG_HAVE_KPROBES but have disabled
CONFIG_KPROBES.
Right now most asm/kprobes.h do not have guards against CONFIG_KPROBES,
this means most architecture code cannot include asm/kprobes.h safely.
Correct this and add guards for architectures missing them.
Additionally provide architectures that not have kprobes support with
the default asm-generic solution. This lets us force asm/kprobes.h on
the header include/linux/kprobes.h always, but most importantly we can
now safely include just asm/kprobes.h on architecture code without
bringing the full kitchen sink of header files.
Two architectures already provided a guard against CONFIG_KPROBES on its
kprobes.h: sh, arch. The rest of the architectures needed gaurds added.
We avoid including any not-needed headers on asm/kprobes.h unless
kprobes have been enabled.
In a subsequent atomic change we can try now to remove compiler.h from
include/linux/kprobes.h.
During this sweep I've also identified a few architectures defining a
common macro needed for both kprobes and ftrace, that of the definition
of the breakput instruction up. Some refer to this as
BREAKPOINT_INSTRUCTION. This must be kept outside of the #ifdef
CONFIG_KPROBES guard.
[mcgrof@kernel.org: fix arm64 build]
Link: http://lkml.kernel.org/r/CAB=NE6X1WMByuARS4mZ1g9+W=LuVBnMDnh_5zyN0CLADaVh=Jw@mail.gmail.com
[sfr@canb.auug.org.au: fixup for kprobes declarations moving]
Link: http://lkml.kernel.org/r/20170214165933.13ebd4f4@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170203233139.32682-1-mcgrof@kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
There is <linux/compiler.h> which provides macros for various gcc
specific constructs. Eg: __weak for __attribute__((weak)). I've
cleaned all instances of gcc specific attributes with the right macros
for all files under /arch/m68k
Link: http://lkml.kernel.org/r/1485540901-1988-3-git-send-email-gidisrael@gmail.com
Signed-off-by: Gideon Israel Dsouza <gidisrael@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access to
devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to be used by
glibc.
- The ability for a guest to ask the hypervisor to resize the guest's hash
table, and in addition support for doing so automatically when memory is
hotplugged into/out-of the guest. This allows the hash table to be sized
based on the current memory usage of the guest, rather than the maximum
possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which includes
support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton Blanchard,
Benjamin Herrenschmidt, Chris Packham, Daniel Axtens, Daniel Borkmann, David
Gibson, Finn Thain, Gautham R. Shenoy, Gavin Shan, Greg Kurz, Joel Stanley,
John Allen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi
Bangoria, Reza Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Icle
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access
to devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to
be used by glibc.
- The ability for a guest to ask the hypervisor to resize the guest's
hash table, and in addition support for doing so automatically when
memory is hotplugged into/out-of the guest. This allows the hash
table to be sized based on the current memory usage of the guest,
rather than the maximum possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which
includes support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton
Blanchard, Benjamin Herrenschmidt, Chris Packham, Daniel Axtens,
Daniel Borkmann, David Gibson, Finn Thain, Gautham R. Shenoy, Gavin
Shan, Greg Kurz, Joel Stanley, John Allen, Madhavan Srinivasan,
Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Reza
Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun"
* tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (129 commits)
powerpc/mm/radix: Skip ptesync in pte update helpers
powerpc/mm/radix: Use ptep_get_and_clear_full when clearing pte for full mm
powerpc/mm/radix: Update pte update sequence for pte clear case
powerpc/mm: Update PROTFAULT handling in the page fault path
powerpc/xmon: Fix data-breakpoint
powerpc/mm: Fix build break with BOOK3S_64=n and MEMORY_HOTPLUG=y
powerpc/mm: Fix build break when CMA=n && SPAPR_TCE_IOMMU=y
powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n
powerpc/pseries: Fix typo in parameter description
powerpc/kprobes: Remove kprobe_exceptions_notify()
kprobes: Introduce weak variant of kprobe_exceptions_notify()
powerpc/ftrace: Fix confusing help text for DISABLE_MPROFILE_KERNEL
powerpc/powernv: Fix opal_exit tracepoint opcode
powerpc: Add a prototype for mcount() so it can be versioned
powerpc: Drop GPL from of_node_to_nid() export to match other arches
powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()
powerpc/kprobes: Implement Optprobes
powerpc/kprobes: Fixes for kprobe_lookup_name() on BE
powerpc: Add helper to check if offset is within relative branch range
powerpc/bpf: Introduce __PPC_SH64()
...
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
The macro TEST_VERIFY_AREA can never be defined as there's no
wp_works_ok variable. So just remove the dead code.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Convert from printk() to pr_*(),
- Add dummies for validating format strings when debugging is
disabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Convert from printk() to pr_*(),
- Add missing print to do_page_mapin(), as print_pte_vaddr() calls
pr_cont().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Use pr_err_ratelimited() instead of deprecated printk_ratelimit(),
- Add dummies for validating format strings when debugging is
disabled,
- Convert from printk() to pr_*(),
- Correct printf()-style format specifiers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Convert from printk() to pr_*(),
- Remove #undef DEBUG,
- Drop useless Warning prefix,
- Use TABs for indentation while at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Convert from printk() to pr_*(),
- Add missing continuations, to fix user-visible breakage,
- Drop useless WARNING prefix,
- Move trailing spaces to start of continuations.
Note that the "Keyboard overrun" message will now only be generated when
the kernel has been compiled for debugging.
Fixes: 4bcc595ccd ("printk: reinstate KERN_CONT for printing continuation lines")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Delete an assignment for the local variable "ret" in an if branch
because it was initialised by the same value.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Mac interrupt code has been debugged. The Penguin deficiencies that
still cause unhandled interrupts aren't fixable here. Besides,
interrupts are fast and frequent and these printk statements
were never really useful IMO. Remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In macints.c there is some startup code which disables the SONIC interrupt
in an attempt to avoid an unhandled slot interrupt, which would be fatal.
This only works on those machines where the SONIC device is on-board.
When the mac_sonic driver is built-in, there's little point in doing this,
because the device will be initialized a few seconds later anyway. But
when mac_sonic is a module, the window for an unhandled interrupt is
longer.
Either way, we've already run the gauntlet for 5 or 10 seconds by the time
we get around to disabling this particular device. It's only by sheer luck
that we got this far.
Really, this is too little too late. The general problem of unhandled
early interrupts also affects other devices on other models. There are
better ways to resolve this problem.
1) When using the Penguin bootloader, boot Mac OS with extensions disabled
(by holding down the shift key at startup or by use of the Extensions
Manager control panel). The Penguin docs already contain this advice,
as it is always effective.
2) Have the Penguin bootloader disable the device. It already attempts
to disable slot interrupts. But since some hardware cannot mask slot
interrupts, Penguin should probably close the relevant device
drivers.
3) Use Emile instead of Penguin. AFAIK the boot ROM never enables network
device interrupts and hence they don't need to be disabled.
Remove this hack. It requires maintenance and it doesn't solve the
problem. It improves the odds for a few models, but so does setting
CONFIG_MAC_SONIC=y.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
mac_nmi_handler() is useless in its present form and locks up my PowerBook
180. Let's throw out the dead code and make it do something useful: print
a register dump and a stack trace.
mac_debug_handler() is also dead code. Remove it along with its static
data.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
arch/m68k/mac/misc.c does not use any miscdevice so the
inclusion of linux/miscdevice.h is unnecessary.
This patch remove this unnecessary include.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Change the device probe test in the via-cuda.c driver so it will load on
Egret-based machines too. Remove the now redundant via-maciisi.c driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cputime_t is now only used by two architectures:
* powerpc (when CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y)
* s390
And since the core doesn't use it anymore, we don't need any arch support
from the others. So we can remove their stub implementations.
A final cleanup would be to provide an efficient pure arch
implementation of cputime_to_nsec() for s390 and powerpc and finally
remove include/linux/cputime.h .
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-36-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Introduce a new architecture-specific get_arch_dma_ops() function
that takes a struct bus_type * argument. Add get_dma_ops() in
<linux/dma-mapping.h>.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change allows us to pass DMA_ATTR_SKIP_CPU_SYNC which allows us to
avoid invoking cache line invalidation if the driver will just handle it
later via a sync_for_cpu or sync_for_device call.
Link: http://lkml.kernel.org/r/20161110113457.76501.77603.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull locking updates from Ingo Molnar:
"The tree got pretty big in this development cycle, but the net effect
is pretty good:
115 files changed, 673 insertions(+), 1522 deletions(-)
The main changes were:
- Rework and generalize the mutex code to remove per arch mutex
primitives. (Peter Zijlstra)
- Add vCPU preemption support: add an interface to query the
preemption status of vCPUs and use it in locking primitives - this
optimizes paravirt performance. (Pan Xinhui, Juergen Gross,
Christian Borntraeger)
- Introduce cpu_relax_yield() and remov cpu_relax_lowlatency() to
clean up and improve the s390 lock yielding machinery and its core
kernel impact. (Christian Borntraeger)
- Micro-optimize mutexes some more. (Waiman Long)
- Reluctantly add the to-be-deprecated mutex_trylock_recursive()
interface on a temporary basis, to give the DRM code more time to
get rid of its locking hacks. Any other users will be NAK-ed on
sight. (We turned off the deprecation warning for the time being to
not pollute the build log.) (Peter Zijlstra)
- Improve the rtmutex code a bit, in light of recent long lived
bugs/races. (Thomas Gleixner)
- Misc fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/paravirt: Fix bool return type for PVOP_CALL()
x86/paravirt: Fix native_patch()
locking/ww_mutex: Use relaxed atomics
locking/rtmutex: Explain locking rules for rt_mutex_proxy_unlock()/init_proxy_locked()
locking/rtmutex: Get rid of RT_MUTEX_OWNER_MASKALL
x86/paravirt: Optimize native pv_lock_ops.vcpu_is_preempted()
locking/mutex: Break out of expensive busy-loop on {mutex,rwsem}_spin_on_owner() when owner vCPU is preempted
locking/osq: Break out of spin-wait busy waiting loop for a preempted vCPU in osq_lock()
Documentation/virtual/kvm: Support the vCPU preemption check
x86/xen: Support the vCPU preemption check
x86/kvm: Support the vCPU preemption check
x86/kvm: Support the vCPU preemption check
kvm: Introduce kvm_write_guest_offset_cached()
locking/core, x86/paravirt: Implement vcpu_is_preempted(cpu) for KVM and Xen guests
locking/spinlocks, s390: Implement vcpu_is_preempted(cpu)
locking/core, powerpc: Implement vcpu_is_preempted(cpu)
sched/core: Introduce the vcpu_is_preempted(cpu) interface
sched/wake_q: Rename WAKE_Q to DEFINE_WAKE_Q
locking/core: Provide common cpu_relax_yield() definition
locking/mutex: Don't mark mutex_trylock_recursive() as deprecated, temporarily
...
- Use seq_puts() for fixed strings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aHq2
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Use seq_puts() for fixed strings"
* tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/atari: Use seq_puts() in atari_get_hardware_list()
m68k/amiga: Use seq_puts() in amiga_get_hardware_list()
Pull m68knommu updates from Greg Ungerer:
"There are two sets of changes in this pull.
The largest is the addition of the ColdFire platform side i2c support
(the IO addressing, setup and clock definitions). The i2c hardware
module itself is driven by the kernels existing iMX i2c driver.
The other change is the addition of support for the Amcore board"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: AMCORE board, add iMX i2c support
m68k: add Sysam AMCORE open board support
m68knommu: platform support for i2c devices on ColdFire SoC
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add support for Sysam AMCORE board, an open hardware embedded Linux
board, see http://sysam.it/openzone/projects/amcore/amcore.html for
any info.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
These changes based on work by Steven King <sfking@fdwdc.com> to support
the i2c hardware modules on ColdFire SoC family devices.
This is the per SoC hardware support. Contains a common platform device
setup. Each of the SoC family members tends to have some minor local
setup required to initialize the module. But all ColdFire family members
use the same i2c hardware module.
This i2c hardware module is the same as used in the Freescale iMX ARM
based family of SoC devices. Steven's original patches were based on using
a new and different i2c-coldfire.c driver. But this is not neccessary as
we can use the existing Linux i2c-imx.c driver with no change required to
it. And this patch is now based on using the existing i2c-imx driver.
This patch only contains the ColdFire platform changes.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
No need to duplicate the same define everywhere. Since
the only user is stop-machine and the only provider is
s390, we can use a default implementation of cpu_relax_yield()
in sched.h.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-s390 <linux-s390@vger.kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1479298985-191589-1-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As there are no users left, we can remove cpu_relax_lowlatency()
implementations from every architecture.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Cc: <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/1477386195-32736-6-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For spinning loops people do often use barrier() or cpu_relax().
For most architectures cpu_relax and barrier are the same, but on
some architectures cpu_relax can add some latency.
For example on power,sparc64 and arc, cpu_relax can shift the CPU
towards other hardware threads in an SMT environment.
On s390 cpu_relax does even more, it uses an hypercall to the
hypervisor to give up the timeslice.
In contrast to the SMT yielding this can result in larger latencies.
In some places this latency is unwanted, so another variant
"cpu_relax_lowlatency" was introduced. Before this is used in more
and more places, lets revert the logic and provide a cpu_relax_yield
that can be called in places where yielding is more important than
latency. By default this is the same as cpu_relax on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1477386195-32736-2-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ndelay() macro definition has an extra semi-colon at the
end of the line thus leading to a compilation error when ndelay is used
in a conditional block without curly braces like this one:
if (cond)
ndelay(t);
else
...
which, after the preprocessor pass gives:
if (cond)
m68k_ndelay(t);;
else
...
thus leading to the following gcc error:
error: 'else' without a previous 'if'
Remove this extra semi-colon.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: c8ee038bd1 ("m68k: Implement ndelay() based on the existing udelay() logic")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Its all generic atomic_long_t stuff now.
Tested-by: Jason Low <jason.low2@hpe.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
