Some boards, like OrangePi PC2 (H5), OrangePi Plus 2E (H3) and Tanix TX6
(H6) don't have external 32kHz oscillator. Till H6, it didn't really
matter if external oscillator was enabled because HW detected error and
fall back to internal one. H6 has same functionality but it's the first
SoC which have "auto switch bypass" bit documented and always enabled in
driver. This prevents RTC to work correctly if external crystal is not
present on board. There are other side effects - all peripherals which
depends on this clock also don't work (HDMI CEC for example).
Make clocks property optional. If it is present, select external
oscillator. If not, stay on internal.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200308135849.106333-2-jernej.skrabec@siol.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion to allow extending
support after 2106 and properly supporting the STv2 range.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200306005809.38530-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PL031 and ST v1 RTC are 32bit seconds counters. STv2 is a BCD RTC
apparently going from 0000 to 9999, hopefully handling the leap days
properly until then.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200306005809.38530-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The datasheet states that 4052 is the maximum value for year. However, the
mpc5121 read_time and set_time function abuse the target time register
instead of using the broken down time so it is limited to 2106.
Link: https://lore.kernel.org/r/20200306074404.58909-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC IRQ is requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Link: https://lore.kernel.org/r/20200306073404.56921-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The CPCAP rtc is a 14bit day counter plus a 17bit seconds counter.
Note that this failed on Nov 10 2014 so it is very likely this driver as
never been used since.
Link: https://lore.kernel.org/r/20200306015703.42101-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Both RTC IRQs are requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the IRQs using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Link: https://lore.kernel.org/r/20200306010146.39762-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Let the core handle offsetting and windowing the RTC range.
This rtc has hours, minutes, seconds and 16bit days. As the driver has the
RTC epoch set to year 2000, this means that the end of the range is 2^16
days minus one second later. This is Sun Jun 6 23:59:59 UTC 2179. This
is better than the currently set year 2099.
Link: https://lore.kernel.org/r/20200305215022.32533-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The code handling invalid alarms meaning the alarm is in the next 24 hours
is not necessary since commit f8245c2688 ("rtc: remove "RTC_ALM_SET mode"
bugs") which actually predates this driver. Since then, .set_alarm is never
called with an invalid alarm and this handling is not necessary in the
driver.
Link: https://lore.kernel.org/r/20200305215022.32533-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This RTC is a 32bit counter running at 16Hz. This overflows every eight
years and a half. However, the driver uses the SW_VALUE register to store
the overflow, extending the counter to 64bit as long as the update happens
before the overflow.
Link: https://lore.kernel.org/r/20200305160452.27808-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Drop the separate driver that registers the EFI rtc on all EFI
systems that have runtime services available, and instead, move
the registration into the core EFI code, and make it conditional
on whether the actual time related services are available.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Fix multiple occurring interrupts for alarm interrupt. RTC module doesn't
clear the alarm interrupt status bit immediately after the interrupt is
triggered.This is due to the sticky nature of the alarm interrupt status
register. The alarm interrupt status register can be cleared only after
the second counter outruns the set alarm value. To fix multiple spurious
interrupts, disable alarm interrupt in the handler and clear the status
bit before enabling the alarm interrupt.
Fixes: 11143c19eb ("rtc: add xilinx zynqmp rtc driver")
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/1581503079-387-1-git-send-email-srinivas.neeli@xilinx.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The alignment of the continuation of the devm_ioremap() call in
sh_rtc_probe() was broken. Join the lines, as all parameters can fit on
a single line.
Fixes: 4bdc0d676a ("remove ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200212084836.9511-1-geert+renesas@glider.be
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
Subsystem:
- the VL_READ and VL_CLR ioctls are now documented and their behavior is
unified across all the drivers.
- RTC_I2C_AND_SPI Kconfig option rework to avoid selecting both REGMAP_I2C and
REGMAP_SPI unecessarily.
Drivers:
- at91rm9200: remove deprecated procfs, add sam9x60, sama5d4 and sama5d2
compatibles.
- cmos: solve lost interrupts issue on MS Surface 3
- hym8563: return proper errno when time is invalid
- rv3029: many fixes, nvram support
-----BEGIN PGP SIGNATURE-----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=e1Xr
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"The VL_READ and VL_CLR ioctls have been reworked to be more useful.
This will not break userspace as there are very few users and they are
using the integer value as a boolean.
Apart from that, two drivers were reworked and a few fixes here and
there for a net reduction of number of lines.
Summary:
Subsystem:
- the VL_READ and VL_CLR ioctls are now documented and their behavior
is unified across all the drivers.
- RTC_I2C_AND_SPI Kconfig option rework to avoid selecting both
REGMAP_I2C and REGMAP_SPI unecessarily.
Drivers:
- at91rm9200: remove deprecated procfs, add sam9x60, sama5d4 and
sama5d2 compatibles.
- cmos: solve lost interrupts issue on MS Surface 3
- hym8563: return proper errno when time is invalid
- rv3029: many fixes, nvram support"
* tag 'rtc-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (63 commits)
dt-bindings: rtc: at91rm9200: document clocks property
rtc: i2c/spi: Avoid inclusion of REGMAP support when not needed
rtc: Kconfig: select REGMAP_I2C when necessary
rtc: Kconfig: properly indent sd3078 entry
rtc: cmos: Refactor code by using the new dmi_get_bios_year() helper
rtc: cmos: Use predefined value for RTC IRQ on legacy x86
rtc: cmos: Stop using shared IRQ
rtc: tps6586x: Use IRQ_NOAUTOEN flag
rtc: at91rm9200: use FIELD_PREP/FIELD_GET
rtc: at91rm9200: avoid time readout in at91_rtc_setalarm
rtc: at91rm9200: move register definitions to C file
rtc: at91rm9200: add sama5d4 and sama5d2 compatibles
dt-bindings: rtc: at91rm9200: convert bindings to json-schema
rtc: at91rm9200: remove procfs information
dt-bindings: atmel, at91rm9200-rtc: add microchip, sam9x60-rtc
rtc: pcf8563: Use BIT
rtc: moxart: Convert to SPDX identifier
rtc: ds1343: Remove unused struct spi_device in struct ds1343_priv
rtc: rx8025: Remove struct i2c_client from struct rx8025_data
rtc: hym8563: Read the valid flag directly instead of caching it
...
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----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=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
- Support mremap() for the VDSO, primarily to allow CRIU to restore the
VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement of
the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs by
running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to
take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXjRnpxYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdNYoA/3ZhgKX1L/hwvkPKwu7FxbL41pjB
WAm8IYDaxPvgxkcSAP9FNNepHK+oBPM8I2e3DvDvmcuYjumztdikzYbJ5HuMBA==
=MV2S
-----END PGP SIGNATURE-----
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
Merely enabling I2C and RTC selects REGMAP_I2C and REGMAP_SPI, even when
no driver needs it. While the former can be moduler, the latter cannot,
and thus becomes built-in.
Fix this by moving the select statements for REGMAP_I2C and REGMAP_SPI
from the RTC_I2C_AND_SPI helper to the individual drivers that depend on
it.
Note that the comment for RTC_I2C_AND_SPI refers to SND_SOC_I2C_AND_SPI
for more information, but the latter does not select REGMAP_{I2C,SPI}
itself, and defers that to the individual drivers, too.
Fixes: 080481f54e ("rtc: merge ds3232 and ds3234")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200112171349.22268-1-geert@linux-m68k.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAl4vKHwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYMPGBAAuVNUZaZfWYHpiVP2oRcUQUguFiD3NTbknsyzV2oH
J9P0GfeENSKwE9OOhZ7XIjnCZAJwQgTK/ppQY5yiQ/KAtYyyXjXEJ6jqqjiTDInr
+3+I3t/LhkgrK7tMrb7ylTGa/d7KhaciljnOXC8+b75iddvM9I1z2pbHDbppZMS9
wT4RXL/cFtRb85AfOyPLybcka3f5P2gGvQz38qyimhJYEzHDXZu9VO1Bd20f8+Xf
eLBKX0o6yWMhcaPLma8tm0M0zaXHEfLHUKLSOkiOk+eHTWBZ3b/w5nsOQZYZ7uQp
25yaClbameAn7k5dHajduLGEJv//ZjLRWcN3HJWJ5vzO111aHhswpE7JgTZJSVWI
ggCVkytD3ESXapvswmACSeCIDMmiJMzvn6JvwuSMVB7a6e5mcqTuGo/FN+DrBF/R
IP+/gY/T7zIIOaljhQVkiEIIwiD/akYo0V9fheHTBnqcKEDTHV4WjKbeF6aCwcO+
b8inHyXZSKSMG//UlDuN84/KH/o1l62oKaB1uDIYrrL8JVyjAxctWt3GOt5KgSFq
wVz1lMw4kIvWtC/Sy2H4oB+RtODLp6yJDqmvmPkeJwKDUcd/1JKf0KsZ8j3FpGei
/rEkBEss0KBKyFAgBSRO2jIpdj2epgcBcsdB/r5mlhcn8L77AS6mHbA173kY4pQ/
Kdg=
=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Refactor code by using the new dmi_get_bios_year() helper instead of
open coding its functionality. This also makes logic slightly clearer.
No changes intended.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When legacy devices are present on x86 machine, the RTC IRQ has
a dedicated pre-defined value. Use it instead of hard coded number.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As reported by Guilherme G. Piccoli:
---8<---8<---8<---
The rtc-cmos interrupt setting was changed in the commit 079062b28f
("rtc: cmos: prevent kernel warning on IRQ flags mismatch") in order
to allow shared interrupts; according to that commit's description,
some machine got kernel warnings due to the interrupt line being shared
between rtc-cmos and other hardware, and rtc-cmos didn't allow IRQ sharing
that time.
After the aforementioned commit though it was observed a huge increase
in lost HPET interrupts in some systems, observed through the following
kernel message:
[...] hpet1: lost 35 rtc interrupts
After investigation, it was narrowed down to the shared interrupts
usage when having the kernel option "irqpoll" enabled. In this case,
all IRQ handlers are called for non-timer interrupts, if such handlers
are setup in shared IRQ lines. The rtc-cmos IRQ handler could be set to
hpet_rtc_interrupt(), which will produce the kernel "lost interrupts"
message after doing work - lots of readl/writel to HPET registers, which
are known to be slow.
Although "irqpoll" is not a default kernel option, it's used in some contexts,
one being the kdump kernel (which is an already "impaired" kernel usually
running with 1 CPU available), so the performance burden could be considerable.
Also, the same issue would happen (in a shorter extent though) when using
"irqfixup" kernel option.
In a quick experiment, a virtual machine with uptime of 2 minutes produced
>300 calls to hpet_rtc_interrupt() when "irqpoll" was set, whereas without
sharing interrupts this number reduced to 1 interrupt. Machines with more
hardware than a VM should generate even more unnecessary HPET interrupts
in this scenario.
---8<---8<---8<---
After looking into the rtc-cmos driver history and DSDT table from
the Microsoft Surface 3, we may notice that Hans de Goede submitted
a correct fix (see dependency below). Thus, we simply revert
the culprit commit.
Fixes: 079062b28f ("rtc: cmos: prevent kernel warning on IRQ flags mismatch")
Depends-on: a1e23a42f1 ("rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs")
Reported-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ_NOAUTOEN flag tells interrupt core that interrupt shall not be
auto-enabled at the time of requesting interrupt. This is a minor clean-up
change that doesn't fix any problems.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106015615.12602-1-digetx@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ROHM BD71828 PMIC RTC block is from many parts similar to one
on BD70528. Support BD71828 RTC using BD70528 RTC driver and
avoid re-inventing the wheel.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The header was simply moved from the arm mach folder to drivers/rtc but
there is not point in having it separated from the driver.
Also remove unused bit definitions and use BIT and GENMASK.
Link: https://lore.kernel.org/r/20191229204421.337612-4-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Our chosen byte swapping, which is what firmware already uses, is to
do readl/writel by normal lw/sw intructions (data invariance). This
also means we need to mangle addresses for u8 and u16 accesses. The
mangling for 16bit has been done aready, but 8bit one was missing.
Correcting this causes different addresses for accesses to the
SuperIO and local bus of the IOC3 chip. This is fixed by changing
byte order in ioc3 and m48rtc_rtc structs.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
struct i2c_client can be referenced from the device structure, so this
doesn't need to have it in struct rx8025_data.
Remove struct i2c_client from struct rx8025_data.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Link: https://lore.kernel.org/r/20191218081624.3307752-1-iwamatsu@nigauri.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC has a valid bit in the seconds register that indicates whether
power was lost since the pevious time set. This bit is currently read
once at probe time, cached and updated with set_time.
Howeever, caching the bit may prevent detecting power loss at runtime
(which can happen if the RTC's supply is distinct from the the platform's).
Writing the seconds register when setting time will clear the bit,
so there should be no downside in reading the bit directly instead of
caching it.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20191212153111.966923-2-paul.kocialkowski@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current code returns -EPERM when the voltage loss bit is set.
Since the bit indicates that the time value is not valid, return
-EINVAL instead, which is the appropriate error code for this
situation.
Fixes: dcaf038493 ("rtc: add hym8563 rtc-driver")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20191212153111.966923-1-paul.kocialkowski@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the current code, the return value of devm_request_threaded_irq may be
returned. This fixes it.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Link: https://lore.kernel.org/r/20191217121231.2698817-2-iwamatsu@nigauri.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The compatibles have been marked obsolete for more that 2 years, drop them
now. Note that this doesn't currently prevent the driver from probing
because the i2c core will still match using the i2c_device_id table.
Link: https://lore.kernel.org/r/20191212230239.65784-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RV3029 can report three different conditions: power on, voltage dropped
and data is lost and voltage is low and temperature compensation has
stopped. The first two conditions amount to the same status, the RTC data
is invalid.
VLOW1 has to be cleared manually to resume temperature compensation, this
is achieved using RTC_VL_CLEAR.
Link: https://lore.kernel.org/r/20191214221022.622482-11-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no point in having 2 indirections before calling regmap_read,
especially since rv3029_get_sr also changes the return value without any
good reason. Call regmap_read directly.
Link: https://lore.kernel.org/r/20191214221022.622482-7-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no lock preventing concurrent access to the status register from
bth the rtc subsystem and the hwmon subsystem. Use regmap_update_bits to
ensure updating RV3029_STATUS is properly locked.
Link: https://lore.kernel.org/r/20191214221022.622482-5-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of trying to validate the accessed registers in custom functions,
let regmap handle that. This allows to defines all the holes in the
register range and gives access to the regmap debugfs register dump.
Link: https://lore.kernel.org/r/20191214221022.622482-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove RTC_VL_CLR handling because it is a disservice to userspace as it
removes the important information that the RTC data is invalid. This may
lead userspace to set an invalid system time later on.
Link: https://lore.kernel.org/r/20191214220259.621996-17-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RV8803_FLAG_V1F means the voltage is too low to keep the temperature
compensation running and the accuracy of the RTC is affected.
RV8803_FLAG_V2F means the voltage dropped so low that data is now invalid.
Link: https://lore.kernel.org/r/20191214220259.621996-16-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stop clearing RV8803_FLAG_V2F in RTC_VL_CLR because it is a disservice to
userspace as it removes the important information that the RTC data is
invalid. This may lead userspace to set an invalid system time later on.
Link: https://lore.kernel.org/r/20191214220259.621996-15-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove RTC_VL_CLR handling because it is a disservice to userspace as it
removes the important information that the RTC data is invalid. This may
lead userspace to set an invalid system time later on.
Link: https://lore.kernel.org/r/20191214220259.621996-13-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove RTC_VL_CLR handling because it is a disservice to userspace as it
removes the important information that the RTC data is invalid. This may
lead userspace to set an invalid system time later on.
Link: https://lore.kernel.org/r/20191214220259.621996-11-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
voltage_low is only updated when reading the time, this means that using
RTC_VL_READ will miss the VL flag if the time has not been read before
using the ioctl. Always read the status from the hardware.
Link: https://lore.kernel.org/r/20191214220259.621996-9-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove RTC_VL_CLR handling because it is a disservice to userspace as it
removes the important information that the RTC data is invalid. This may
lead userspace to set an invalid system time later on.
Link: https://lore.kernel.org/r/20191214220259.621996-7-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Alarm registers high byte was reserved for other functions.
This add mask in alarm registers operation functions.
This also fix error condition in interrupt handler.
Fixes: fc2979118f ("rtc: mediatek: Add MT6397 RTC driver")
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1576057435-3561-6-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current use of mode flags to us SPI_MODE_3 and
SPI_CS_HIGH is fragile: it overwrites anything already
assigned by the SPI core. Change it thusly:
- Just |= the SPI_MODE_3 so we keep other flags
- Assign ^= SPI_CS_HIGH since we might be active high
already, and that is usually the case with GPIOs used
for chip select, even if they are in practice active low.
Add a comment clarifying why ^= SPI_CS_HIGH is the right
choice here.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191204225731.20306-1-linus.walleij@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When support for the R40 in the rtc-sun6i driver was split out for a
separate compatible string, only the RTC half was covered, and not the
clock half. Unfortunately this results in the whole driver not working,
as the RTC half expects the clock half to have been initialized.
Add support for the clock part as well. The clock part is like the H3,
but does not need to export the internal oscillator, nor does it have
a gateable LOSC external output.
This fixes issues with WiFi and Bluetooth not working on the BPI M2U.
Fixes: d6624cc750 ("rtc: sun6i: Add R40 compatible")
Cc: <stable@vger.kernel.org> # 5.3.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191205085054.6049-1-wens@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The resume() forgets to call clk_disable_unprepare() when failed.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191205160655.32188-1-hslester96@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The devm_request_threaded_irq function allocates irq that is
released when a driver detaches. Thus, there is no reason to
explicitly call free_irq in probe function.
Fixes: 851b87148a ("rtc: mt6397: improvements of rtc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20191113021720.9527-1-weiyongjun1@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- fix warnings and errors with make W=1
- UIE are now disabled while setting the RTC time
- UIE are now disallowed when the RTC time is not set.
Drivers:
- remove unecessary .remove callbacks
- Set RTC range for cros-ec, ds1343, ds1347, m41t80, s35390a, vt8500
- Use devm_platform_ioremap_resource where applicable
- rv3028: add clock out support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEycoQi/giopmpPgB12wIijOdRNOUFAl3k7FMACgkQ2wIijOdR
NOX63hAAqeoBWKVHgh5kltmtd7RCWD3cazleYvPPfCyoNUOz1YB6Gblp4R+5ImNT
pFfbhk44baMDBSy5zlJV4yLkdsBYx5Yx7Su56zAqMYhpnVbvwGeNOsoWLaJThc3o
b8NK9Za9CwwZNm3CDoPdJNeHNOce20Hj9JKCeOyS3Gl7IuMP+0xGXlPVpM0yX4EW
7iwuGhnQNWFM1GQQ8WWgEr4mQB+8xwjy2hKQ2FnKfVk6cqq2wxgrY+XGjV1h1jCM
x/KlmAY9sbntwEZA3ZOqk0LQvMMaKqUEfMpd24joGvo7JGseN/e4aapRXoang3vp
h/mkeW3MnrsGs+YPsSQqdOSrIJ/Qou25QnMXEzRPgkBCXw0lpHkqmF3GdF6CPEFG
xnGZVLrCA1W8ysJNq9ZkavZCEaG9ay6Qd8sOh7Tfl2UkPDArOC1PiKvfzVmkcYZ+
TOwgB7/Yyp9Y1l9asBQnOEzg2AZ0Rq8KlFk5vAxiyQOBpivWEw8AuNMG+W8B16NE
bsc6rteNYzfLJusxuEQTdG7/AsLNun+YQoASAYaoIxnnzcslUwMRLl/JoNRQOt7D
sdaTHd10I99+282hWPnFSkb3Xm44+01tX2apGPQt5Duv8ojQYHTRoPhHYmIvCkLJ
HM8HWNae6bNKyUhsxDG8iFHfbAhL6ojr/AEiXw58TZjfPe3i5iw=
=gBQF
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A lot of unnecessary code removal in here that ends up decreasing the
number of lines in the subsystem. The ds1343 and ds1347 drivers got
cleaned up. The rest are the usual fixes and new features.
Subsystem:
- fix warnings and errors with make W=1
- UIE are now disabled while setting the RTC time
- UIE are now disallowed when the RTC time is not set.
Drivers:
- remove unecessary .remove callbacks
- Set RTC range for cros-ec, ds1343, ds1347, m41t80, s35390a, vt8500
- Use devm_platform_ioremap_resource where applicable
- rv3028: add clock out support"
* tag 'rtc-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (81 commits)
rtc: Fix Kconfig indentation
rtc: xgene: Remove unused struct device in struct xgene_rtc_dev
rtc: sun6i: Remove struct device from sun6i_rtc_dev
rtc: st-lpc: Remove struct resource from struct st_rtc
rtc: pcf8523: Remove struct pcf8523
rtc: meson: remove redundant assignment to variable retries
rtc: v3020: remove set but unused variable
rtc: tegra: remove set but unused variable
rtc: pm8xxx: update kerneldoc for struct pm8xxx_rtc
rtc: m41t80: remove excess kerneldoc
rtc: ds1685: fix build error with make W=1
rtc: ds1685: remove set but unused variables
rtc: ds1374: remove unused variable
rtc: sysfs: fix hctosys_show kerneldoc
rtc: interface: fix kerneldoc comments
rtc: msm6242: Remove unneeded msm6242_set()/msm6242_clear() functions
rtc: msm6242: Fix reading of 10-hour digit
rtc: tps65910: allow using RTC without alarm interrupt
rtc: fsl-ftm-alarm: remove select FSL_RCPM and default y from Kconfig
rtc: pcf8563: Constify clkout_rates
...
- Add support for a "resource managed strongly uncachable ioremap" call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
- New Drivers
- Add support for MediaTek MT6323 PMIC
- New Device Support
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
- New Functionality
- Add support for requested supply clocks; madera-core
- Fix-ups
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona, syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
- Bug Fixes
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAl3f2k4ACgkQUa+KL4f8
d2GmohAAluAT7hhURCf2HECsbVpeLH5i5UahRTCAlyIqeAiOjGEBGdIT2fYM1B+3
daqj3XiiLqvlnT5FZc4Fw5gR9Nu6Oe+Fo+6p6NnAu7CIt+x9RXOTB5LLXYYKICZK
c32SnsSbRQwtzu83d3CjlfQRUZh66fJksWVPnOBkenaR7HaQlujKydBAk3kkLygZ
3GGTzjTXakl/53XJLRNn2wVVEG2gCicZwWxmWYW2000PFWo1upCeJRcwHBOXyy1I
oh+KNp28gVQLT3pOte4TZEO3GNacMMs5DvA0hj2j7j+nH5FOryEPjUNbrqkcR+9T
aquGbgYWgfJrW9UJhgNVsn754y5sgZ48Q20533AICMDfy3JTzfn91pX5q8mVFaPl
Kf4cTVAau7kUCVxrXWuOG2fG2r7BjRABKU5ODDsGWmfWQNdktvLvHJI4j97ct0xj
neBijJya70woV1o40v5yTmcUcc7hGEoKXuRWslxNK3K+nQkgRKMKgY4dm3jBeSmD
lmBrjtjT0gcNl6+bOOn6IXn5k3sxWUwa799LUDaR5oHj6kB0LkIqz3h6UlOBryKO
iQ2xXXCf/gAlkL75SW1rjYBHWkMkswgigppcbw2HB9tMqGL2LtHtgIli8CfGz1vs
BzwxOQRvMK+4rG0qNHbocXJK2O4PduTxMXtBDiVK/tXrHaNLs7I=
=mugH
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for a "resource managed strongly uncachable ioremap"
call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
New Drivers:
- Add support for MediaTek MT6323 PMIC
New Device Support:
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
New Functionality:
- Add support for requested supply clocks; madera-core
Fix-ups:
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona,
syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
Bug Fixes:
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc"
* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
Revert "mfd: syscon: Set name of regmap_config"
mfd: ti_am335x_tscadc: Fix static checker warning
mfd: bd70528: Staticize bit value definitions
mfd: mfd-core: Honour Device Tree's request to disable a child-device
dt-bindings: mfd: max77693: Fix missing curly brace
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
mfd: db8500-prcmu: Support U8420-sysclk firmware
dt-bindings: mfd: max77650: Convert the binding document to yaml
mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
mfd: mfd-core: Remove mfd_clone_cell()
mfd: mfd-core: Protect against NULL call-back function pointer
mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
mfd: cs5535-mfd: Request shared IO regions centrally
mfd: cs5535-mfd: Remove mfd_cell->id hack
mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
mfd: madera: Add support for requesting the supply clocks
...
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133940.13881-1-krzk@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
struct pcf8523 is referenced only by pcf8523_probe(). And member variable in
this is not referenced by any function. Remove struct pcf8523.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Link: https://lore.kernel.org/r/20191123090838.1619-1-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The variable retries is being initialized with a value that is never
read and it is being updated later with a new value in a for-loop.
The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20191122225210.109172-1-colin.king@canonical.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the following warning:
drivers/rtc/rtc-v3020.c: In function ‘rtc_probe’:
drivers/rtc/rtc-v3020.c:287:6: warning: variable ‘temp’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20191122102212.400158-9-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the following warning:
drivers/rtc/rtc-tegra.c: In function ‘tegra_rtc_read_time’:
drivers/rtc/rtc-tegra.c:106:11: warning: variable ‘msec’ set but not used [-Wunused-but-set-variable]
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191122102212.400158-8-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The change from u8 ctrl_reg to const struct pm8xxx_rtc_regs *regs; did not
properly update the kerneldoc comment. Fixes:
drivers/rtc/rtc-pm8xxx.c:64: warning: Function parameter or member 'regs' not described in 'pm8xxx_rtc'
Fixes: c8d523a4b0 ("drivers/rtc/rtc-pm8xxx.c: rework to support pm8941 rtc")
Link: https://lore.kernel.org/r/20191122102212.400158-7-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the following warnings:
drivers/rtc/rtc-ds1685.c: In function ‘ds1685_rtc_read_time’:
drivers/rtc/rtc-ds1685.c:264:5: warning: variable ‘ctrlb’ set but not used [-Wunused-but-set-variable]
264 | u8 ctrlb, century;
| ^~~~~
drivers/rtc/rtc-ds1685.c: In function ‘ds1685_rtc_proc’:
drivers/rtc/rtc-ds1685.c:758:19: warning: variable ‘ctrlc’ set but not used [-Wunused-but-set-variable]
758 | u8 ctrla, ctrlb, ctrlc, ctrld, ctrl4a, ctrl4b, ssn[8];
| ^~~~~
Cc: Joshua Kinard <kumba@gentoo.org>
Acked-By: Joshua Kinard <kumba@gentoo.org>
Link: https://lore.kernel.org/r/20191122102212.400158-4-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix warning:
drivers/rtc/rtc-ds1374.c: In function ‘ds1374_wdt_disable’:
drivers/rtc/rtc-ds1374.c:442:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20191122102212.400158-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix undocumented function parameters:
drivers/rtc/sysfs.c:112: warning: Function parameter or member 'dev' not described in 'hctosys_show'
drivers/rtc/sysfs.c:112: warning: Function parameter or member 'attr' not described in 'hctosys_show'
drivers/rtc/sysfs.c:112: warning: Function parameter or member 'buf' not described in 'hctosys_show'
Link: https://lore.kernel.org/r/20191122102212.400158-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix kerneldoc warnings:
drivers/rtc/interface.c:619: warning: Function parameter or member 'num' not described in 'rtc_handle_legacy_irq'
drivers/rtc/interface.c:619: warning: Function parameter or member 'mode' not described in 'rtc_handle_legacy_irq'
drivers/rtc/interface.c:804: warning: Function parameter or member 'rtc' not described in 'rtc_timer_enqueue'
drivers/rtc/interface.c:804: warning: Function parameter or member 'timer' not described in 'rtc_timer_enqueue'
drivers/rtc/interface.c:864: warning: Function parameter or member 'rtc' not described in 'rtc_timer_remove'
drivers/rtc/interface.c:864: warning: Function parameter or member 'timer' not described in 'rtc_timer_remove'
drivers/rtc/interface.c:900: warning: Function parameter or member 'work' not described in 'rtc_timer_do_work'
drivers/rtc/interface.c:1035: warning: Function parameter or member 'rtc' not described in 'rtc_read_offset'
drivers/rtc/interface.c:1035: warning: Function parameter or member 'offset' not described in 'rtc_read_offset'
drivers/rtc/interface.c:1070: warning: Function parameter or member 'rtc' not described in 'rtc_set_offset'
drivers/rtc/interface.c:1070: warning: Function parameter or member 'offset' not described in 'rtc_set_offset'
Link: https://lore.kernel.org/r/20191127082932.666869-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The msm6242_set()/msm6242_clear() functions are used when writing to Control
Register D to set or clear the HOLD bit when reading the current time from
the RTC.
Doing this with a read-modify-write cycle will potentially clear an
interrupt condition which occurs between the read and the write.
The datasheet states the following about this:
When writing the HOLD or 30 second adjust bits of register D, it is
necessary to write the IRQ FLAG bit to a "1".
Since the only other bits in the register are the 30 second adjust bit
(which is not used) and the BUSY bit (which is read-only), the
read-modify-write cycle can be replaced by a simple write with the IRQ FLAG
bit set to 1 and the other bits (except HOLD) set to 0.
Tested-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Link: https://lore.kernel.org/r/20191116114620.9193-1-jongk@linux-m68k.org
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The driver was reading the wrong register as the 10-hour digit due to
a misplaced ')'. It was in fact reading the 1-second digit register due
to this bug.
Also remove the use of a magic number for the hour mask and use the define
for it which was already present.
Fixes: 4f9b9bba1d ("rtc: Add an RTC driver for the Oki MSM6242")
Tested-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Link: https://lore.kernel.org/r/20191116110548.8562-1-jongk@linux-m68k.org
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If tps65910 INT1 pin (IRQ output) is not wired to any IRQ controller,
then it can't be used as system wakeup/alarm source,
but it is still possible to read/write time from/to RTC.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://lore.kernel.org/r/20191116203748.27166-1-andrej.skvortzov@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Flextimer alarm is primarily used as a wakeup source for system
power management. But it shouldn't select the power management driver
as they don't really have dependency of each other.
Also remove the default y as it is not a critical feature for the
systems.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/1573252856-11759-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When using following operations:
date -s "21190910 19:20:00"
hwclock -w
to change date from 2019 to 2119 for test, it will fail on Hygon
Dhyana and AMD Zen CPUs, while the same operations run ok on Intel i7
platform.
MC146818 driver use function mc146818_set_time() to set register
RTC_FREQ_SELECT(RTC_REG_A)'s bit4-bit6 field which means divider stage
reset value on Intel platform to 0x7.
While AMD/Hygon RTC_REG_A(0Ah)'s bit4 is defined as DV0 [Reference]:
DV0 = 0 selects Bank 0, DV0 = 1 selects Bank 1. Bit5-bit6 is defined
as reserved.
DV0 is set to 1, it will select Bank 1, which will disable AltCentury
register(0x32) access. As UEFI pass acpi_gbl_FADT.century 0x32
(AltCentury), the CMOS write will be failed on code:
CMOS_WRITE(century, acpi_gbl_FADT.century).
Correct RTC_REG_A bank select bit(DV0) to 0 on AMD/Hygon CPUs, it will
enable AltCentury(0x32) register writing and finally setup century as
expected.
Test results on Intel i7, AMD EPYC(17h) and Hygon machine show that it
works as expected.
Compiling for sparc64 and alpha architectures are passed.
Reference:
https://www.amd.com/system/files/TechDocs/51192_Bolton_FCH_RRG.pdf
section: 3.13 Real Time Clock (RTC)
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jinke Fan <fanjinke@hygon.cn>
Link: https://lore.kernel.org/r/20191105083943.115320-1-fanjinke@hygon.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The module alias platform tag contains a spelling mistake. Fix it.
Fixes: f33506abbcdd ("rtc: bd70528: Add MODULE ALIAS to autoload module")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191106083418.159045-1-colin.king@canonical.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The bd70528 RTC driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell
for RTC is added.
I'm not sure if this is a bugfix or feature addition but I guess
fixes tag won't harm in this case.
Fixes: 32a4a4ebf7 ("rtc: bd70528: Initial support for ROHM bd70528 RTC")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20191023114711.GA13954@localhost.localdomain
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC month value is 1-indexed, but the kernel assumes it is 0-indexed.
This may result in the RTC not rolling over correctly.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Link: https://lore.kernel.org/r/20191101095422.14787-1-ilya@compulab.co.il
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This driver forgets to disable and unprepare clock when remove.
Add a call to clk_disable_unprepare to fix it.
Fixes: c4f07ecee2 ("rtc: brcmstb-waketimer: Add Broadcom STB wake-timer")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20191105160043.20018-1-hslester96@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core now has error messages in case of registration failure, there
is no need to have other messages in the drivers.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20191016201414.30934-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
dpm_sysfs_remove() and device_pm_remove() are already called by
device_del() on device removal so there is no need to call
device_init_wakeup(dev, false) from the driver and it allows to remove the
.remove callback.
Link: https://lore.kernel.org/r/20191021155806.3625-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
dpm_sysfs_remove() and device_pm_remove() are already called by
device_del() on device removal so there is no need to call
device_init_wakeup(dev, false) from the driver and it allows to remove the
.remove callback.
Link: https://lore.kernel.org/r/20191021155806.3625-4-alexandre.belloni@bootlin.com
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
dpm_sysfs_remove() and device_pm_remove() are already called by
device_del() on device removal so there is no need to call
device_init_wakeup(dev, false) from the driver and it allows to remove the
.remove callback.
Link: https://lore.kernel.org/r/20191021155806.3625-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
dpm_sysfs_remove() and device_pm_remove() are already called by
device_del() on device removal so there is no need to call
device_init_wakeup(dev, false) from the driver and it allows to remove the
.remove callback.
Link: https://lore.kernel.org/r/20191021155806.3625-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When setting the time in the future with the uie timer enabled,
rtc_timer_do_work will loop for a while because the expiration of the uie
timer was way before the current RTC time and a new timer will be enqueued
until the current rtc time is reached.
If the uie timer is enabled, disable it before setting the time and enable
it after expiring current timers (which may actually be an alarm).
This is the safest thing to do to ensure the uie timer is still
synchronized with the RTC, especially in the UIE emulation case.
Reported-by: syzbot+08116743f8ad6f9a6de7@syzkaller.appspotmail.com
Fixes: 6610e0893b ("RTC: Rework RTC code to use timerqueue for events")
Link: https://lore.kernel.org/r/20191020231320.8191-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
use mt6397 rtc driver also for mt6323 but with different
base/size see "mfd: mt6323: add mt6323 rtc+pwrc"
Signed-off-by: Josef Friedl <josef.friedl@speed.at>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- use regmap_read_poll_timeout to drop while-loop
- use devm-api to drop remove-callback
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Josef Friedl <josef.friedl@speed.at>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
move code to separate header-file to reuse definitions later
in poweroff-driver (drivers/power/reset/mt6323-poweroff.c)
Suggested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Josef Friedl <josef.friedl@speed.at>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All watchdog drivers implement the same set of ioctl commands, and
fortunately all of them are compatible between 32-bit and 64-bit
architectures.
Modern drivers always go through drivers/watchdog/wdt.c as an abstraction
layer, but older ones implement their own file_operations on a character
device for this.
Move the handling from fs/compat_ioctl.c into the individual drivers.
Note that most of the legacy drivers will never be used on 64-bit
hardware, because they are for an old 32-bit SoC implementation, but
doing them all at once is safer than trying to guess which ones do
or do not need the compat_ioctl handling.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We no longer need the rtc compat handling to be in common code, now that
all drivers are either moved to the rtc-class framework, or (rarely)
exist in drivers/char for architectures without compat mode (m68k,
alpha and ia64, respectively).
I checked the list of ioctl commands in drivers, and the ones that are
not already handled are all compatible, again with the one exception of
m68k driver, which implements RTC_PLL_GET and RTC_PLL_SET, but has no
compat mode.
Unlike earlier versions of this patch, I'm now adding a separate
compat_ioctl handler that takes care of RTC_IRQP_READ32/RTC_IRQP_SET32
and treats all other commands as compatible, leaving the native
behavior unchanged.
The old conversion handler also deals with RTC_EPOCH_READ and
RTC_EPOCH_SET, which are not handled in rtc-dev.c but only in a single
device driver (rtc-vr41xx), so I'm adding the compat version in the same
place. I don't expect other drivers to need those commands in the future.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
v4: handle RTC_EPOCH_SET32 in rtc_dev_compat_ioctl
v3: handle RTC_IRQP_READ32/RTC_IRQP_SET32 in rtc_dev_compat_ioctl
v2: merge compat handler into ioctl function to avoid the
compat_alloc_user_space() roundtrip, based on feedback
from Al Viro.
Linux should handle when the pcf2127 watchdog feature is enabled by the
bootloader. This is done by checking the watchdog timer value during
init, and set the WDOG_HW_RUNNING flag if the value differs from zero.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191021080838.2789-1-martin@geanix.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
rv3028 provides clkout (enabled by default). Add clkout
to clock framework source and control from device tree for
variable frequency with enable and disable functionality.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Link: https://lore.kernel.org/r/20191018100425.1687979-1-pn@denx.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to call device_init_wakeup(dev, false) in .remove as
device_del will take care of that. It is also not necessary to
devm_free_irq. Finally, dev_pm_clear_wake_irq can be called
unconditionally.
Link: https://lore.kernel.org/r/20191019204941.6203-9-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Rework the interrupt handling to avoid caching the values as the core is
already doing that. The core also always ensures the rtc_time passed for
the alarm is fully populated.
The only trick is in read_alarm where status needs to be read before the
alarm registers to ensure the potential irq is not cleared.
Link: https://lore.kernel.org/r/20191019204941.6203-8-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
SGI Octane (IP30) doesn't have RTC register directly mapped into CPU
address space, but accesses RTC registers with an address and data
register. This is now supported by additional access functions, which
are selected by a new field in platform data. Removed plat_read/plat_write
since there is no user and their usage could introduce lifetime issue,
when functions are placed in different modules.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Reviewed-by: Joshua Kinard <kumba@gentoo.org>
Link: https://lore.kernel.org/r/20191014214621.25257-1-tbogendoerfer@suse.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
A few of the fields in struct ds1685_priv aren't needed at all,
so we can remove it.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Link: https://lore.kernel.org/r/20191011150546.9186-1-tbogendoerfer@suse.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If the RTC HW returns an invalid time, the rtc_year_days()
call would crash. This patch adds error logging in this
situation, and removes the tm_yday and tm_wday calculations.
These fields should not be relied upon by userspace
according to man rtc, and thus we don't need to calculate
them.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Daniel Campello <campello@chromium.org>
Link: https://lore.kernel.org/r/20191004142608.170159-1-ncrews@chromium.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The comment in the probe function stating that it disables oscillator stop
detection and glitch filtering is incorrect as it sets bits 3 and 4 while
it should be setting 5 and 6 to achieve that. Then, it is safe to assume
that the oscillator failure detection is actually enabled.
Properly handle oscillator failures by returning -EINVAL when the time and
date are know to be incorrect and reset the flag when the time is set.
Link: https://lore.kernel.org/r/20191007134724.15505-8-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the more modern API to get the match data out of the of match table.
This saves some code, lines, and nicely avoids referencing the match
table when it is undefined with configurations where CONFIG_OF=n.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-rtc@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191004214334.149976-4-swboyd@chromium.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
platform_get_irq_byname() might return -errno which later would be
cast to an unsigned int and used in request_irq().
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20191004150510.6278-1-krzk@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
