Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a regulator is listed in devicetree, but the node is marked as
"disabled" we should skip parsing the regulator init data and
deny consumers from interacting with the regulator. This
simplifies devicetree maintenance where we can have one dtsi file
with all regulators supported by a PMIC and then select what
regulators are used depending on the board configuration.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded semicolons after the switch statement to satisfy
coccicheck.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When drivers use simplified DT parsing method (they provide
'regulator_desc.of_match') they still may want to parse custom
properties for some of the regulators. For example some of the
regulators support GPIO enable control.
Add a driver-supplied callback for such case. This way the regulator
core parses common bindings offloading a lot of code from drivers and
still custom properties may be used.
The callback, called for each parsed regulator, may modify the
'regulator_config' initially passed to regulator_register().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support their operating mode to be changed on startup
or by consumers when the system is running while others only support
their operating mode to be changed while the system has entered in a
suspend state.
The regulator Device Tree binding documents a set of properties to
configure the regulators operating modes from a FDT. This patch builds
on (40e20d6 regulator: of: Add support for parsing regulator_state for
suspend state) and adds support to parse those properties and fill the
regulator constraints so the regulator core can call the right suspend
handlers when the system enters into sleep.
The modes are defined in the Device Tree using the hardware specific
modes supported by the regulators. Regulator drivers have to define a
translation function that is used to map the hardware specific modes
to the standard ones.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers can use the of_regulator_match() function to parse the regulator
init_data from DT. A match table is used to specify the name of the node
containing the regulators, the device node and to return the init_data
to the caller.
But also the static regulator descriptor is needed to correctly extract
some DT properties like the regulator initial and suspend modes. Use the
match table to pass that information.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_get_regulator_init_data() function is used to extract the regulator
init_data but information on how to extract certain data is defined in the
static regulator descriptor (e.g: how to map the hardware operating modes).
Add a const struct regulator_desc * parameter to the function signature so
the parsing logic could use the information in the struct regulator_desc.
of_get_regulator_init_data() relies on of_get_regulation_constraints() to
actually extract the init_data so it has to pass the struct regulator_desc
but that is modified on a later patch.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Leverage all the work that was done in (40e20d6 regulator: of: Add
support for parsing regulator_state for suspend state) and throw in
the ability to set suspend microvolts from the device tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'regulator_states' array is used only in this unit and it is not
exported. Make it static.
This also fixes following sparse warning:
drivers/regulator/of_regulator.c:22:12: warning: symbol 'regulator_states' was not declared. Should it be static?
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Description of regulators should generally be optional so if there is no
DT node for the regulators container then we shouldn't print an error
message. Lower the severity of the message to debug level (it might help
someone work out what went wrong) and while we're at it say what we were
looking for.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_get_regulation_constraints() calls of_get_child_by_name() to find the
regulator-state-{mem,disk} child nodes for each regulator. This function
increments the device node reference counter but this is not decremented
once the function is done using the node.
Fix that by calling of_node_put() after finishing using the device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulation_constraints structure includes specific field to support
suspend state for global PMIC SUSPEND/HIBERNATE mode. This patch add support
for parsing regulator_state for suspend state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regulator drivers which support DT all repeat very similar code
to supply a list of known regulator identifiers to be matched with DT,
convert that to platform data which is then matched up with the regulators
as they are registered. This is both fiddly to get right and for devices
which can use the standard helpers to provide their operations is the main
source of code in the driver.
Since this code is essentially identical for most drivers we can factor it
out into the core, moving the identifiers in the match table into the
regulator descriptors and also allowing drivers to pass in the name of the
subnode to search. When a driver provides an of_match string for the
regulator the core will attempt to use that to obtain init_data, allowing
the driver to remove all explicit code for DT parsing and simply provide
data instead.
The current code leaks the phandles for the child nodes, this will be
addressed incrementally and makes no practical difference for FDT anyway
as the DT data structures are never freed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls in of_get_regulation_constraints() where
possible (note that of_property_read_{bool|u32}() were already used to read
some properties).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than requiring individual drivers to put the of_nodes returned
from of_regulator_match use devres to put them. This also has the
benefit it makes the life-time of the of_nodes match the lifetime of
the init data also contained in the of_regulator_match structure, which
seems more consistent.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As of_regulator_match will take an of_node reference to each matched
regulator, it makes sense to provide a helper to put all those
references. This patch does that.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, of_regulator_match does not increment the reference count of
the of_nodes it takes new references to. This could cause the node
pointer held to be invalid, by the time it is passed to the regulator
core. This patchs adds an of_node_get when we copy each of_node pointer
into the match structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The turn-on time of the regulator depends on the regulator device's
electrical characteristics. Sometimes regulator turn-on time also
depends on the capacitive load on the given platform and it can be
more than the datasheet value.
The driver provides the enable-time as per datasheet.
Add support for configure the enable ramp time through regulator
constraints so that regulator core can take this value for enable
time for that regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Added a property to indicate if the regulator supports bypass mode.
Also modified of_get_regulation_constraints() to check for that
property and set appropriate constraints.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_regulator_match() saves some dynamcially allocated state into the
match table that's passed to it. By implementation and not contract, for
each match table entry, if non-NULL state is already present,
of_regulator_match() will not overwrite it. of_regulator_match() is
typically called each time a regulator is probe()d. This means it is
called with the same match table over and over again if a regulator
triggers deferred probe. This results in stale, kfree()d data being left
in the match table from probe to probe, which causes a variety of crashes
or use of invalid data.
Explicitly free all output state from of_regulator_match() before
generating new results in order to avoid this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When the bindings for the TPS6586x regulator were being proposed, I
asserted that DT node naming rules for bus child nodes should also be
applied to nodes inside the TPS6586x regulator node itself. In other
words, that each node providing regulator init data should be named
after the type of object it represented ("regulator") and hence that
some other property was required to indicate which regulator the node
described ("regulator-compatible"). In turn this led to multiple nodes
having the same name, thus requiring node names to use a unit address
to make them unique, thus requiring reg properties within the nodes and
However, subsequent discussion indicates that the rules I was asserting
only applies to standardized bus nodes, and within a device's own node,
the binding can basically do anything sane that it wants.
Hence, this change deprecates the register-compatible property, and
instead uses node names to replace this functionality. This greatly
simplifies the device tree content, making them smaller and more legible.
The code is changed such that old device trees continue to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Match the device's regulators with the property of
"regulator-compatible" of each regulator node.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.
regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).
[Rewrote subject for 80 columns -- broonie]
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Looking up init data for regulators found on chips is a common operation
that can be handled in a generic way. The new helper function introduced
by this patch looks up the children of a given node by names specified
in a match table and fills that match table with information parsed from
the DT.
This is based on work by Rhyland Klein <rklein@nvidia.com>.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
apply_uV is errornously set when regulator is instantiated from device
tree, even when it doesn't contain any voltage constraints.
This commit fixes error:
machine_constraints_voltage: CHARGER: failed to apply 0uV constraint
for following regulator description in DTS:
CHARGER {
regulator-min-microamp = <100000>;
regulator-max-microamp = <200000>;
}
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's not always true that the device_node of regulator can be found
at dev->of_node at the time when of_get_regulator_init_data() is being
called, because in some cases the regulator nodes in device tree do
not have 'struct device' behind them until regulator_dev gets created
for it by core function regulator_register().
The patch adds device_node as a new parameter to
of_get_regulator_init_data(), so that caller can pass in the node of
regulator directly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise there is no way in the bindings to configure a fixed voltage
via software. It seems reasonable to assume that if the binding explicitly
specifies a voltage we want to actually use that voltage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_regulator_init_data is called in drivers/regulator/fixed.c
which could be a module.
Export of_get_regulator_init_data to fix below build error:
ERROR: "of_get_regulator_init_data" [drivers/regulator/fixed.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The helper routine is meant to be used by the regulator drivers
to extract the regulator_init_data structure from the data
that is passed from device tree.
'consumer_supplies' which is part of regulator_init_data is not extracted
as the regulator consumer mappings are passed through DT differently,
implemented in subsequent patches.
Similarly the regulator<-->parent/supply mapping is handled in
subsequent patches.
Also add documentation for regulator bindings to be used to pass
regulator_init_data struct information from device tree.
Some of the regulator properties which are linux and board specific,
are left out since its not clear if they can
be in someway embedded into the kernel or passed in from DT.
They will be revisited later.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
