In hardware mode we can not use the software demuxer, this means that the
selected scan mask needs to match one of the available scan masks exactly.
It also means that all attached buffers need to use the same scan mask.
Given that when operating in hardware mode there is typically only a single
buffer attached to the device this not an issue. Add a sanity check to make
sure that only a single buffer is attached in hardware mode nevertheless.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For each buffer type specify the supported device modes for this buffer.
This allows us for devices which support multiple different operating modes
to pick the correct operating mode based on the modes supported by the
attached buffers.
It also prevents that buffers with conflicting modes are attached
to a device at the same time or that a buffer with a non-supported mode is
attached to a device (e.g. in-kernel callback buffer to a device only
supporting hardware mode).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Even if no userspace consumer buffer is attached to the IIO device at
registration we still need to compute the masklength, since it is possible
that a in-kernel consumer buffer is going to get attached to the device at
a later point.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The same code is executed regardless ret value, so this test
can be removed.
Also fix coverity scan CID 1268786.
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently when something goes wrong at some step when disabling the buffers
we immediately abort. This has the effect that the enable/disable calls are
no longer balanced. So make sure that even if one step in the disable
sequence fails the other steps are still executed.
The other issue is that when either enable or disable fails buffers that
were active at that time stay active while the device itself is disabled.
This leaves things in a inconsistent state and can cause unbalanced
enable/disable calls. Furthermore when enable fails we restore the old scan
mask, but still keeps things disabled.
Given that verification of the configuration was performed earlier and it
is valid at the point where we try to enable/disable the most likely reason
of failure is a communication failure with the device or maybe a
out-of-memory situation. There is not really a good recovery strategy in
such a case, so it makes sense to leave the device disabled, but we should
still leave it in a consistent state.
What the patch does if disable/enable fails is to deactivate all buffers
and make sure that the device will be in the same state as if all buffers
had been manually disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
__iio_update_buffers is already a rather large function with many different
error paths and it is going to get even larger. This patch factors out the
device enable and device disable paths into separate helper functions.
The patch also re-implements iio_disable_all_buffers() using the new
iio_disable_buffers() function removing a fair bit of redundant code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently __iio_update_buffers() verifies whether the new configuration
will work in the middle of the update sequence. This means if the new
configuration is invalid we need to rollback the changes already made. This
patch moves the validation of the new configuration at the beginning of
__iio_update_buffers() and will not start to make any changes if the new
configuration is invalid.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We only have to call the request_update() callback for a newly inserted
buffer. The configuration of the already previously active buffers will not
have changed.
This also allows us to move the request_update() call to the beginning of
__iio_update_buffers(), before any currently active buffers are stopped.
This makes the error handling a lot easier since no changes were made to
the buffer list and no rollback needs to be performed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a small helper function iio_free_scan_mask() that takes a mask and
frees its memory if the scan masks for the device are dynamically
allocated, otherwise does nothing. This means we don't have to open-code
the same check over and over again in __iio_update_buffers.
Also free compound_mask as soon a we are done using it. This constrains its
usage to a specific region of the function will make further refactoring
and splitting the function into smaller sub-parts more easier.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While more verbose error messages are useful for debugging we should really
not put those error messages into the kernel log for normal errors that are
already reported to the application via the error code, when running in
non-debug mode.
Otherwise application authors might expect that this is part of the ABI and
to get the error they should scan the kernel log. Which would be rather
error prone itself since there is no direct mapping between a operation and
the error message so it is impossible to find out which error message
belongs to which error.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some devices have hardware buffers that can store a number of samples
for later consumption. Hardware usually provides interrupts to notify
the processor when the FIFO is full or when it has reached a certain
watermark level. This helps with reducing the number of interrupts to
the host processor and thus it helps decreasing the power consumption.
This patch enables usage of hardware FIFOs for IIO devices in
conjunction with software device buffers. When the hardware FIFO is
enabled the samples are stored in the hardware FIFO. The samples are
later flushed to the device software buffer when the number of entries
in the hardware FIFO reaches the hardware watermark or when a flush
operation is triggered by the user when doing a non-blocking read
on an empty software device buffer.
In order to implement hardware FIFO support the device drivers must
implement the following new operations: setting and getting the
hardware FIFO watermark level, flushing the hardware FIFO to the
software device buffer. The device must also expose information about
the hardware FIFO such it's minimum and maximum watermark and if
necessary a list of supported watermark values. Finally, the device
driver must activate the hardware FIFO when the device buffer is
enabled, if the current device settings allows it.
The software device buffer watermark is passed by the IIO core to the
device driver as a hint for the hardware FIFO watermark. The device
driver can adjust this value to allow for hardware limitations (such
as capping it to the maximum hardware watermark or adjust it to a
value that is supported by the hardware). It can also disable the
hardware watermark (and implicitly the hardware FIFO) it this value is
below the minimum hardware watermark.
Since a driver may support hardware FIFO only when not in triggered
buffer mode (due to different semantics of hardware FIFO sampling and
triggered sampling) this patch changes the IIO core code to allow
falling back to non-triggered buffered mode if no trigger is enabled.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the IIO buffer blocking read only wait until at least one
data element is available.
This patch makes the reader sleep until enough data is collected before
returning to userspace. This should limit the read() calls count when
trying to get data in batches.
Co-author: Yannick Bedhomme <yannick.bedhomme@mobile-devices.fr>
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
[rebased and remove buffer timeout]
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move all core (non-custom) buffer attributes to a vector to make it
easier to add more of them in the future.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There was a need for non triggered software buffer type. It can be used when
triggered model does not fit and INDIO_BUFFER_HARDWARE causes confusion because
the data stream can be obtained not directly form hardware backend.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We already do have the length field in the struct iio_buffer which is
expected to be in sync with the current size of the buffer. And currently
all implementations of the get_length callback either return this field or a
constant number.
This patch removes the get_length callback and replaces all occurrences in
the IIO core with directly accessing the length field of the buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If a buffer implementation does not implement the set_length() callback the
length will be static and can not be changed by userspace. Mark the length
attribute as a read only property in this case so userspace is aware of this
rather than just silently accepting any length value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All buffers want at least the length and the enable attribute. Move the
creation of those attributes to the core instead of having to do this in
each individual buffer implementation. This allows us to get rid of some
boiler-plate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The next patch will introduce new dependencies in iio_buffer_alloc_sysfs()
to functions which are currently defined after iio_buffer_alloc_sysfs(). To
avoid forward declarations move both iio_buffer_alloc_sysfs() and
iio_buffer_free_sysfs() after those function.
This is split into two patches one moving the functions and one adding the
dependencies to make review of the actual changes easier.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Originally device and buffer registration were kept as separate operations
in IIO to allow to register two distinct sets of channels for buffered and
non-buffered operations. This has since already been further restricted and
the channel set registered for the buffer needs to be a subset of the
channel set registered for the device. Additionally the possibility to not
have a raw (or processed) attribute for a channel which was registered for
the device was added a while ago. This means it is possible to not register
any device level attributes for a channel even if it is registered for the
device. Also if a channel's scan_index is set to -1 and the channel is
registered for the buffer it is ignored.
So in summary it means it is possible to register the same channel array for
both the device and the buffer yet still end up with distinctive sets of
channels for both of them. This makes the argument for having to have to
manually register the channels for both the device and the buffer invalid.
Considering that the vast majority of all drivers want to register the same
set of channels for both the buffer and the device it makes sense to move
the buffer registration into the core to avoid some boiler-plate code in the
device driver setup path.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Individual drivers should not be messing with the scan mask that contains
the list of enabled channels. This is something that is supposed to be
managed by the core.
Now that the last few drivers that used it to configure a default scan mask
have been updated to not do this anymore we can unexport the function.
Note, this patch also requires moving a few functions around so they are all
declared before the first internal user.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Maintainer Updates
* Add 3 designated reviewers for IIO. Lars, Peter and Hartmut have been
actively reviewing a lot of patches for a while now so this reflects
the status quo. These three are probably the only reason I keep
my head above the water!
New drivers and device support
* max5821 DAC
* Rockchip SARADC
* TI ADC128S052 ADC
* BMC150 Accelerometer
* exynos ADC driver gains support for s3c24xx and s3c64xx parts.
* kxcjk-1013 gainst range control and runtime PM support to drive
down it's power usage.
Driver removals
* Drop ad5930, ad99850, ad9852, ad9910 and ad9951 drivers on the simple
basis that they drivers just provided a register write function with
no compliant user space ABI whatsoever. Much better to drop them and
start again for these in the fullness of time.
Core Enhancements
* Join together neighbouring elements in the demux units that feeds
the binary interfaces. This cuts down on the number of individual
copies needed when splitting out individual channels from the incoming
channel scans.
* Other demux related cleanups such as using roundup instead of a local
implementation.
Cleanups
* Drop an unnecessary double setting of the owner field in xilinx adc.
* Some more patches to use managed (devm) interfaces to cut down on
complexity of removal code.
* adis16060 coding style fixlets.
* Fix some incorrect error returns in the Xilinx ADC driver.
* Coding style fixlets for various accelerometer drivers.
* Some sparse warning fixes to do with endianness and sign of variables.
* Fix an incorrect and entirely pointless use of sizeof on a dynamic pointer
in hid-sensor-magn-3d by dropping the relevant code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zqHo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-next
Jonathan writes:
1st round of new IIO drivers, functionality and cleanups for the 3.18 cycle.
Maintainer Updates
* Add 3 designated reviewers for IIO. Lars, Peter and Hartmut have been
actively reviewing a lot of patches for a while now so this reflects
the status quo. These three are probably the only reason I keep
my head above the water!
New drivers and device support
* max5821 DAC
* Rockchip SARADC
* TI ADC128S052 ADC
* BMC150 Accelerometer
* exynos ADC driver gains support for s3c24xx and s3c64xx parts.
* kxcjk-1013 gainst range control and runtime PM support to drive
down it's power usage.
Driver removals
* Drop ad5930, ad99850, ad9852, ad9910 and ad9951 drivers on the simple
basis that they drivers just provided a register write function with
no compliant user space ABI whatsoever. Much better to drop them and
start again for these in the fullness of time.
Core Enhancements
* Join together neighbouring elements in the demux units that feeds
the binary interfaces. This cuts down on the number of individual
copies needed when splitting out individual channels from the incoming
channel scans.
* Other demux related cleanups such as using roundup instead of a local
implementation.
Cleanups
* Drop an unnecessary double setting of the owner field in xilinx adc.
* Some more patches to use managed (devm) interfaces to cut down on
complexity of removal code.
* adis16060 coding style fixlets.
* Fix some incorrect error returns in the Xilinx ADC driver.
* Coding style fixlets for various accelerometer drivers.
* Some sparse warning fixes to do with endianness and sign of variables.
* Fix an incorrect and entirely pointless use of sizeof on a dynamic pointer
in hid-sensor-magn-3d by dropping the relevant code.
The size of the allocation is currently set to the size of the pointer
rather than the structure we should actually be allocating.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: kbuild@01.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no one
was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1wYACgkQMUfUDdst+ykrNwCgswPkRSAPQ3C8WvLhzUYRZZ/L
AqEAoJP0Q8Fz8unXjlSMcx7pgcqUaJ8G
=mrTQ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no
one was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while"
* tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (2199 commits)
staging: comedi: addi_apci_1564: remove diagnostic interrupt support code
staging: comedi: addi_apci_1564: add subdevice to check diagnostic status
staging: wlan-ng: coding style problem fix
staging: wlan-ng: fixing coding style problems
staging: comedi: ii_pci20kc: request and ioremap memory
staging: lustre: bitwise vs logical typo
staging: dgnc: Remove unneeded dgnc_trace.c and dgnc_trace.h
staging: dgnc: rephrase comment
staging: comedi: ni_tio: remove some dead code
staging: rtl8723au: Fix static symbol sparse warning
staging: rtl8723au: usb_dvobj_init(): Remove unused variable 'pdev_desc'
staging: rtl8723au: Do not duplicate kernel provided USB macros
staging: rtl8723au: Remove never set struct pwrctrl_priv.bHWPowerdown
staging: rtl8723au: Remove two never set variables
staging: rtl8723au: RSSI_test is never set
staging:r8190: coding style: Fixed checkpatch reported Error
staging:r8180: coding style: Fixed too long lines
staging:r8180: coding style: Fixed commenting style
staging: lustre: ptlrpc: lproc_ptlrpc.c - fix dereferenceing user space buffer
staging: lustre: ldlm: ldlm_resource.c - fix dereferenceing user space buffer
...
When copying multiple multiple samples that are adjacent in both the source as
well as the destination buffer, instead of creating a new demux table entry for
each sample just increase the length of the previous entry by the size of the
new sample. This makes the demuxing process slightly more efficient.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Makes the code slightly shorter and a bit easier to understand.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When creating the demux table we need to iterate over the selected scan mask for
the buffer to get the samples which should be copied to destination buffer.
Right now the code uses the mask which contains all active channels, which means
the demux table contains entries which causes it to copy all the samples from
source to destination buffer one by one without doing any demuxing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
Change sca3000_ring implementation so that it exports a data_available
function to iio.
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current scan element type uses the following format:
[be|le]:[s|u]bits/storagebits[>>shift].
To specify multiple elements in this type, added a repeat value.
So new format is:
[be|le]:[s|u]bits/storagebitsXr[>>shift].
Here r is specifying how may times, real/storage bits are repeating.
When X is value is 0 or 1, then repeat value is not used in the format,
and it will be same as existing format.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=HMr3
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First found of IIO fixes for the 3.15 cycle.
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
Ensure that querying the IIO buffer scan_mask returns a value of
0 or 1. Currently querying the scan mask has the value returned
by test_bit(), which returns either true or false. For some
architectures test_bit() may return -1 for true, which will appear
to return an error when returning from iio_scan_mask_query().
Additionally, it's important for the sysfs interface to consistently
return the same thing when querying the scan_mask.
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Get rid of obsolete uses of goto error_ret and some empty lines.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the IIO buffer interface only allows non-blocking reads. This patch
adds support for blocking IO. In blocking mode the thread will go to sleep if no
data is available and will wait for the buffer implementation to signal that new
data is available by waking up the buffers waitqueue.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a new data_available() callback to the iio_buffer_access_funcs
struct. The callback is used to indicate whether data is available in the buffer
for reading. It is meant to replace the stufftoread flag from the iio_buffer
struct. The reasoning for this is that the buffer implementation usually can
determine whether data is available rather easily based on its state, on the
other hand it can be rather tricky to update the stufftoread flag in a race free
way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The functionality implemented by iio_sw_buffer_preenable() is now done directly
in the IIO core and previous users of iio_sw_buffer_preenable() have all been
updated to not use it anymore. It is unused now and can be remove.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently a IIO device driver needs to make sure to update the buffer's bytes
per datum after the scan mask has changed. This is usually done in the preenable
callback by invoking iio_sw_buffer_preenable(). This is something that needs to
be done and is done for virtually all devices which support buffers (we
currently have only one exception). Also this a bit of a layering violation
since we have to call the buffer setup ops from the device setup ops. This
requires the device driver to know about the internal requirements of the buffer
(e.g. whether we need to call the set_bytes_per_datum) callback. And especially
with in-kernel buffer consumers, which allows to attach arbitrary buffers to a
device, this is something that the driver can't know.
Moving this to the core allows us to drop the individual calls to
iio_sw_buffer_preenable() from drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Usually the active scan mask is freed in __iio_update_buffers() when the buffer
is disabled. But when the device is still sampling when it is removed we'll end
up disabling the buffers in iio_disable_all_buffers(). So we also need to free
the active scan mask here, otherwise it will be leaked.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since the kernel now disables all buffers when a device is unregistered it might
happen that a in-kernel consumer tries to disable that buffer again. So ignore
requests where the buffer already is in the desired state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have the same code to free a IIO device attribute list in multiple place.
This patch adds a new helper function to take care of this and replaces the
custom instances with a call to the helper function. Note that we do not need to
call list_del() for each of the list items since we will never look at any of
the list items nor the list itself again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We need to make sure that in-kernel users of iio_update_buffers() do not race
against each other or against unregistration of the device. So we need to take
both the mlock and the info_exist_lock when calling iio_update_buffers() from a
in-kernel consumer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Once the device has been unregistered there won't be any new data no matter how
long a userspace application waits, so we might as well wake them up and let
them know.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the IIO device has been unregistered return -ENODEV for any further file
operations like read() and ioctl(). This avoids userspace being able to grab new
references to the device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since the buffer is accessed by userspace we can not just free the buffers
memory once we are done with it in kernel space. There might still be open file
descriptors and userspace still might be accessing the buffer. This patch adds
support for reference counting to the IIO buffers. When a buffer is created and
initialized its initial reference count is set to 1. Instead of freeing the
memory of the buffer the buffer's _free() function will drop that reference
again. But only after the last reference to the buffer has been dropped the
buffer the buffer's memory will be freed. The IIO device will take a reference
to its primary buffer. The patch adds a small helper function for this called
iio_device_attach_buffer() which will get a reference to the buffer and assign
the buffer to the IIO device. This function must be used instead of assigning
the buffer to the device by hand. The reference is only dropped once the IIO
device is freed and we can be sure that there are no more open file handles. A
reference to a buffer will also be taken whenever the buffer is active to avoid
the buffer being freed while data is still being send to it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves the merge problem with two iio drivers that Stephen
Rothwell pointed out.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to stop sampling when the device is removed, otherwise it will
continue to sample forever.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
if device has available_scan_masks set and the buffer is enabled without
any scan_elements enabled, in a NULL pointer is dereferenced in iio_compute_scan_bytes()
[ 18.993713] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 19.002593] pgd = debd4000
[ 19.005432] [00000000] *pgd=9ebc0831, *pte=00000000, *ppte=00000000
[ 19.012329] Internal error: Oops: 17 [#1] PREEMPT ARM
[ 19.017639] Modules linked in:
[ 19.020843] CPU: 0 Not tainted (3.9.11-00036-g75c888a-dirty #207)
[ 19.027587] PC is at _find_first_bit_le+0xc/0x2c
[ 19.032440] LR is at iio_compute_scan_bytes+0x2c/0xf4
[ 19.037719] pc : [<c021dc60>] lr : [<c03198d0>] psr: 200d0013
[ 19.037719] sp : debd9ed0 ip : 00000000 fp : 000802bc
[ 19.049713] r10: 00000000 r9 : 00000000 r8 : deb67250
[ 19.055206] r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : deb67000
[ 19.062011] r3 : de96ec00 r2 : 00000000 r1 : 00000004 r0 : 00000000
[ 19.068847] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 19.076324] Control: 10c5387d Table: 9ebd4019 DAC: 00000015
problem is the rollback code in iio_update_buffers(), old_mask may be NULL (e.g. on first
call)
I'm not too confident about the fix; works for me...
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change the type of the 'data' parameter for iio_push_to_buffers() from 'u8 *' to
'const void *'. Drivers typically use the correct type (e.g. __be16 *) for their
data buffer. When passing the buffer to iio_push_to_buffers() it needs to be
cast to 'u8 *' for the compiler to not complain (and also having to add __force
if we want to keep sparse happy as well). Since the buffer implementation should
not care about the data layout (except the size of one sample) using a void
pointer is the correct thing to do. Also make it const as the buffer
implementations are not supposed to modify it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
