At least on dm81xx, we can get the davinci_emac MAC address the same
way as on am33xx cpsw.
Let's also use ether_addr_copy() for davinci_emac while at it.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.
At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wait_on_bit_timeout() is a simpler and race-free way of waiting for
a bit to be cleared than the current code in btusb.c. This patch updates
the code to use the helper function (its btusb copy - to be later
updated to use a global one).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The test for BTUSB_DOWNLOADING must be after adding to the wait queue
and setting the TASK_INTERRUPTIBLE state. Otherwise the flag may get
cleared after we test for it and we end up getting a timeout since
schedule_timeout() waits for the full duration. This patch uses a
wait_on_bit_timeout() + wake_up_bit(). To perform the task both
race-free as well as in a much simpler way.
Since there's no global wait_on_bit_timeout() helper yet (even though
all the building blocks for it are in place) this patch creates a
temporary local btusb copy of it until the global one has made it to
upstream trees.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In general all Intel Bluetooth devices support retrieving of additional
exception information. However for older generations including Wilkens
Peak and Stone Peak it is not as simple. So for now only enable the
Intel specific error handling for Snowfield Peak and later devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PZQW
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.20-20150128' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-28-01
this is a pull request of 12 patches for net-next/master.
There are 3 patches by Ahmed S. Darwish, which update the kvaser_usb
driver and add support for the USBcan-II based adapters. Stéphane
Grosjean contributes 7 patches for the peak_usb driver, which add
support for the CANFD USB adapters. I contribute 2 patches which clean
up the peak_usb driver structure a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cd1e65044d ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So we
don't need to do the check again in the platform device driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When many pf_packet listeners are created on a lot of interfaces the
current implementation using global packet type lists scales poorly.
This patch adds per net_device packet type lists to fix this problem.
The patch was originally written by Eric Biederman for linux-2.6.29.
Tested on linux-3.16.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFLA_LINK_NETNSID is used, the netdevice should be built in this link netns
and moved at the end to another netns (pointed by the socket netns or
IFLA_NET_NS_[PID|FD]).
Existing user of the newlink handler will use the netns argument (src_net) to
find a link netdevice or to check some other information into the link netns.
For example, to find a netdevice, two information are required: an ifindex
(usually from IFLA_LINK) and a netns (this link netns).
Note: when using IFLA_LINK_NETNSID and IFLA_NET_NS_[PID|FD], a user may create a
netdevice that stands in netnsX and with its link part in netnsY, by sending a
rtnl message from netnsZ.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Bluetooth controllers from Atheros use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BugLink: https://bugs.launchpad.net/bugs/1400215
ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.
This workaround is from Qualcomm, they also did some workarounds in
Windows driver.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Such a feature doesn't exist and isn't really needed since you
probably won't have enough interfaces to make it worthwhile, so
just remove that from the documentation.
Reported-by: booto [on IRC]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Bluetooth HCI transport specification for USB device defines on how
a standard AMP controller is identified and operated. This patch adds
the needed handling to hook it up to the Bluetooth stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
TIME_WAIT sockets are not owning any skb.
ip_send_unicast_reply() and tcp_v6_send_response() both use
regular sockets.
We can safely remove a test in sch_fq and save one cache line miss,
as sk_state is far away from sk_pacing_rate.
Tested at Google for about one year.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ACT_CONNMARK fails to build if NF_CONNTRACK_MARK is disabled,
and d7924450e1 ("act_connmark: Add missing dependency on
NF_CONNTRACK_MARK") fixed that case, but missed the cased where
NF_CONNTRACK is a loadable module.
This adds the second dependency to ensure that NET_ACT_CONNMARK
can only be built-in if NF_CONNTRACK is also part of the kernel
rather than a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock_iocb structure is allocate on stack for each read/write-like
operation on sockets, and contains various fields of which only the
embedded msghdr and sometimes a pointer to the scm_cookie is ever used.
Get rid of the sock_iocb and put a msghdr directly on the stack and pass
the scm_cookie explicitly to netlink_mmap_sendmsg.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The if block was supposed to have curly braces. In the current code we
complain about dropped rx packets when we shouldn't.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it isn't possible to request checksums on the outer UDP
header of tunnels - the TUNNEL_CSUM flag is ignored. This adds
support for requesting that UDP checksums be computed on transmit
and properly reported if they are present on receive.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first NFC pull request for 3.20.
With this one we have:
- Secure element support for the ST Micro st21nfca driver. This depends
on a few HCI internal changes in order for example to support more
than one secure element per controller.
- ACPI support for NXP's pn544 HCI driver. This controller is found on
many x86 SoCs and is typically enumerated on the ACPI bus there.
- A few st21nfca and st21nfcb fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SNWp
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC: 3.20 first pull request
This is the first NFC pull request for 3.20.
With this one we have:
- Secure element support for the ST Micro st21nfca driver. This depends
on a few HCI internal changes in order for example to support more
than one secure element per controller.
- ACPI support for NXP's pn544 HCI driver. This controller is found on
many x86 SoCs and is typically enumerated on the ACPI bus there.
- A few st21nfca and st21nfcb fixes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel Bluetooth devices use the generic USB device/interface class
descriptors that are assigned to Bluetooth H:2 conforming transports.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
However newer chips have a bootloader stage and require firmware to
be loaded before they are functional. To avoid any confusion for the
users, just ignore unknown Intel Bluetooth devices.
All the released Intel Bluetooth devices have an entry in the device
table identifying their setup and support requirements. The advantage
here is that older kernel can be booted with newer devices without
causing any disturbance.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
New entries to the USB blacklist/quirk device table should be sorted
by USB vendor id. Fix the recent entry fro Marvell devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The smp_unregister() function needs to be called every time the
controller is powered down. There are multiple entry points when
this can happen. One is "hciconfig hci0 reset" which will throw
a WARN_ON when LE support has been enabled.
[ 78.564620] WARNING: CPU: 0 PID: 148 at net/bluetooth/smp.c:3075 smp_register+0xf1/0x170()
[ 78.564622] Modules linked in:
[ 78.564628] CPU: 0 PID: 148 Comm: kworker/u3:1 Not tainted 3.19.0-rc4-devel+ #404
[ 78.564629] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
[ 78.564635] Workqueue: hci0 hci_rx_work
[ 78.564638] ffffffff81b4a7a2 ffff88001cb2fb38 ffffffff8161d881 0000000080000000
[ 78.564642] 0000000000000000 ffff88001cb2fb78 ffffffff8103b870 696e55206e6f6f6d
[ 78.564645] ffff88001d965000 0000000000000000 0000000000000000 ffff88001d965000
[ 78.564648] Call Trace:
[ 78.564655] [<ffffffff8161d881>] dump_stack+0x4f/0x7b
[ 78.564662] [<ffffffff8103b870>] warn_slowpath_common+0x80/0xc0
[ 78.564667] [<ffffffff81544b00>] ? add_uuid+0x1f0/0x1f0
[ 78.564671] [<ffffffff8103b955>] warn_slowpath_null+0x15/0x20
[ 78.564674] [<ffffffff81562d81>] smp_register+0xf1/0x170
[ 78.564680] [<ffffffff81081236>] ? lock_timer_base.isra.30+0x26/0x50
[ 78.564683] [<ffffffff81544bf0>] powered_complete+0xf0/0x120
[ 78.564688] [<ffffffff8152e622>] hci_req_cmd_complete+0x82/0x260
[ 78.564692] [<ffffffff8153554f>] hci_cmd_complete_evt+0x6cf/0x2e20
[ 78.564697] [<ffffffff81623e43>] ? _raw_spin_unlock_irqrestore+0x13/0x30
[ 78.564701] [<ffffffff8106b0af>] ? __wake_up_sync_key+0x4f/0x60
[ 78.564705] [<ffffffff8153a2ab>] hci_event_packet+0xbcb/0x2e70
[ 78.564709] [<ffffffff814094d3>] ? skb_release_all+0x23/0x30
[ 78.564711] [<ffffffff81409529>] ? kfree_skb+0x29/0x40
[ 78.564715] [<ffffffff815296c8>] hci_rx_work+0x1c8/0x3f0
[ 78.564719] [<ffffffff8105bd91>] ? get_parent_ip+0x11/0x50
[ 78.564722] [<ffffffff8105be25>] ? preempt_count_add+0x55/0xb0
[ 78.564727] [<ffffffff8104f65f>] process_one_work+0x12f/0x360
[ 78.564731] [<ffffffff8104ff9b>] worker_thread+0x6b/0x4b0
[ 78.564735] [<ffffffff8104ff30>] ? cancel_delayed_work_sync+0x10/0x10
[ 78.564738] [<ffffffff810542fa>] kthread+0xea/0x100
[ 78.564742] [<ffffffff81620000>] ? __schedule+0x3e0/0x980
[ 78.564745] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564749] [<ffffffff816246ec>] ret_from_fork+0x7c/0xb0
[ 78.564752] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564755] ---[ end trace 8b0d943af76d3736 ]---
This warning is not critical and has only been placed in the code to
actually catch this exact situation. To avoid triggering it move
the smp_unregister() into hci_dev_do_close() which will now also
take care of remove the SMP channel. It is safe to call this function
since it only remove the channel if it has been previously registered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Bluetooth controllers can provide an additional exception
info string when a hardware error event occurs. The core will now
call hdev->hw_error to let the driver read out this information.
This change will cause a reset of the hardware to bring it back
into functional state and then read the Intel exception info
string and print it along with the error information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When receiving a HCI Hardware Error event, the controller should be
assumed to be non-functional until issuing a HCI Reset command.
The Bluetooth hardware errors are vendor specific and so add a
new hdev->hw_error callback that drivers can provide to run extra
code to handle the hardware error.
After completing the vendor specific error handling perform a full
reset of the Bluetooth stack by closing and re-opening the transport.
Based-on-patch-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Split the hci_dev_reset ioctl handling into using hci_dev_do_reset
helper function. Similar to what has been done with hci_dev_do_open
and hci_dev_do_close.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The discovery state should be set to stopped when the HCI device is
powered off. This patch adds the appropriate call to the
hci_discovery_set_state() function from hci_dev_do_close() which is
responsible for the power-off procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_Reset is issued the discovery state is assumed to be stopped.
The hci_cc_reset() handler was trying to set the state but it was doing
it without using the hci_discovery_set_state() function. Because of this
e.g. the mgmt Discovering event could go without being sent. This patch
fixes the code to use the hci_discovery_set_state() function instead of
just blindly setting the state value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's a check in set_secure_conn() that's supposed to ensure that SSP
is enabled before we try to request the controller to enable SC (since
SSP is a pre-requisite for it). However, this check only makes sense for
controllers actually supporting BR/EDR SC. If we have a 4.0 controller
we're only interested in the LE part of SC and should therefore not be
requiring SSP to be enabled. This patch adds an additional condition to
check for lmp_sc_capable(hdev) before requiring SSP to be enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The btusb_disconnect() callback calls hci_unregister_dev() which in turn
calls btusb_close() if the HCI device is powered. The btusb_close()
function in turn will call btusb_free_frags(). It's therefore
unnecessary to have another call to btusb_free_frags() in the
btusb_disconnect() function. Besides the redundancy the second call
seems to also cause some strange stability issues which this patch then
also fixes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When loading the Intel firmware it can happen that the firmware loading
complete vendor event arrives before the command complete event for the
last firmware fragment.
< HCI Command: Vendor (0x3f|0x0009) plen 7
01 02 fc 03 00 00 00
> HCI Event: Vendor (0xff) plen 5
06 00 00 00 00
> HCI Event: Command Complete (0x0e) plen 4
Vendor (0x3f|0x0009) ncmd 31
Status: Success (0x00)
This is mainly caused by the fact that the vendor command and its
command complete event are transported over the bulk endpoints. The
firmware loading complete event however is send over the interrupt
endpoint. So with just bad timing one event arrives before the other.
Currently the code does not account for it. There are precautions for
receiving firmware loading complete event quickly, but not for receiving
it before the command complete.
Introduce an extra flag that tracks when the firmware sending has
completed from the driver point of view and track the completion of
the firmware loading procedure with a different flag. That way the
wakeup can be handled properly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If Secure Connections Only mode has been enabled, the it is important
to check that OOB data for P-256 values is provided. In case it is not,
then tell the remote side that no OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When replying to the IO capability request for Secure Simple Pairing and
Secure Connections, the OOB data present fields needs to set. Instead of
making the calculation inline, split this into a separate helper
function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When Secure Connections Only mode has been enabled and remote OOB data
is requested, then only provide P-256 hash and randomizer vaulues. The
fields for P-192 hash and randomizer should be set to zero.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Until legacy SMP OOB pairing is implemented user space should be given a
clear error when trying to use it. This patch adds a corresponding check
to the Add Remote OOB Data handler function which returns "invalid
parameters" if non-zero Rand192 or Hash192 parameters were given for an
LE address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a common function that pushes the skb in the network queue with adding
timestamps information, converted from time values read from the
PEAK USB adapters.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
The communication protocol has been developed using some mechanisms that
did exist in the PCAN-USB Pro, thus, this patch also changes some
previously static functions and data into global ones.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
includes changes that deal with the new struct canfd_frame.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
does the mandatory changes to support new data bittiming specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the definition of a new callback that enable any PEAK-System CAN USB
adapter to grant read access to its Bus Error Counters value. This ability is
not supported by all the PEAK-System adapters, thus, for those, the callback
pointer will be initiaized to NULL, which is correct regarding the linux-can
device driver specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Export the ctrlmode_supported value from the core file to each adapter specific
file. This has been mandatory for supporting the new CANFD extension.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A "struct peak_usb_adapter" describes a certain USB adapter, as this doesn't
change during runtime, this patch marks all USB adapter definitions as const.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the list "static struct peak_usb_adapter
*peak_usb_adapters_list[]" to be used with ARRAY_SIZE not with a NULL
termination, as the size is known during compile time.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN to USB interfaces sold by the Swedish manufacturer Kvaser are
divided into two major families: 'Leaf', and 'USBcanII'. From an
Operating System perspective, the firmware of both families behave
in a not too drastically different fashion.
This patch adds support for the USBcanII family of devices to the
current Kvaser Leaf-only driver.
CAN frames sending, receiving, and error handling paths has been
tested using the dual-channel "Kvaser USBcan II HS/LS" dongle. It
should also work nicely with other products in the same category.
List of new devices supported by this driver update:
- Kvaser USBcan II HS/HS
- Kvaser USBcan II HS/LS
- Kvaser USBcan Rugged ("USBcan Rev B")
- Kvaser Memorator HS/HS
- Kvaser Memorator HS/LS
- Scania VCI2 (if you have the Kvaser logo on top)
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace most of the can interface's state and error counters
handling with the new can-dev can_change_state() mechanism.
Suggested-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update all of the can interface's state and error counters before
trying any skb allocation that can actually fail with -ENOMEM.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
'make pdfdocs' failed for 80211.tmpl and reported errors of the form:
'document type does not allow element "refentry" here'
Fix this by moving </section> tags to a location that makes sense,
this fixes the errors and the pdf looks OK in relevant areas.
Signed-off-by: Sharon Dvir <sharon.dvir1@mail.huji.ac.il>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andy Shevchenko says:
====================
stmmac: Enable Intel Quark SoC X1000 Ethernet support
This is third version of the patch series [1] to bring network card support to
Intel Quark SoC.
The series has been tested on Intel Galileo board.
Changelog v3:
- rebase on top of recent net-next
- rework an approach to get the custom configuration
- rework an approach how to get unique bus_id
- improve DMI lookup function
[1] http://www.spinics.net/lists/netdev/msg296010.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
