This driver is unused and depends on the deprecated soc-camera framework.
Move it to staging in preparation for being removed unless someone does
the work to convert it to a proper V4L2 subdev driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
1 warning regressions:
+ drivers/media/i2c/tda1997x.c: warning: variable 'last_irq_status' set but not used [-Wunused-but-set-variable]: => 1421:17
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the TDA1997x HDMI receivers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix type 'testin' -> 'testing']
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert all g/s_parm calls to g/s_frame_interval. This allows us
to remove the g/s_parm ops since those are a duplicate of
g/s_frame_interval.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old license information with the corresponding SPDX
license for those drivers Cisco authored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When built on a platform without gpiolib support, we run into
a couple of compile errors in ov7740, including:
drivers/media/i2c/ov7740.c: In function 'ov7740_set_power':
drivers/media/i2c/ov7740.c:307:4: error: implicit declaration of function 'gpiod_direction_output'; did you mean 'gpio_direction_output'? [-Werror=implicit-function-declaration]
gpiod_direction_output(ov7740->pwdn_gpio, 0);
drivers/media/i2c/ov7740.c:914:4: error: 'GPIOD_OUT_HIGH' undeclared (first use in this function); did you mean 'GPIOF_INIT_HIGH'?
Changing it to use the correct header file solves the problem.
Fixes: 39c5c4471b ("media: i2c: Add the ov7740 image sensor driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add nop variant of media_entity_cleanup. This allows calling
media_entity_cleanup whether or not Media controller is enabled,
simplifying driver code.
Also drop #ifdefs on a few drivers around media_entity_cleanup().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Time to time, stream on is failing with a strange positive error.
Error code is returned erroneously by ov5640_set_ctrl_exposure()
due to ov5640_get_vts() return value wrongly treated as error.
Fix this by forcing ret to 0 after ov5640_get_vts() success call,
in order that ret is set to success for rest of code sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned:
drivers/media/i2c/dw9714.c: warning: incorrect type in initializer (different base types): => 64:19
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The client field in driver's struct is redundant. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Call pm_runtime_idle() at the end of the driver's probe() function to
enable the device to reach low power state once probe() finishes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support of DVP parallel mode in addition of
existing MIPI CSI mode. The choice between two modes
and configuration is made through device tree.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mt9m111 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Create a source pad and set the media controller type to the sensor.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so that the
subdevice device node is created.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov7740 (color) image sensor is a high performance VGA CMOS
image snesor, which supports for output formats: RAW RGB and YUV
and image sizes: VGA, and QVGA, CIF and any size smaller.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Smatch complains that "err" can be uninitialized if we have a zero size
write. The flow analysis is a little complicated so I'm not sure if
that's possible or not, but it's harmless to set this to zero and it
makes the code easier to read.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the V4L2 AS3645A sub-device driver in favour of the LED flash class
driver for the same hardware, drivers/leds/leds-as3645a.c. The latter uses
the V4L2 flash LED class framework to provide V4L2 sub-device interface.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most of the I2C headers got moved a long time ago to
include/media/i2c. Stop including them at the patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, the same I2C address were used on multiple places.
After I2C rebinding changes, this is no longer needed. So, we
can just get rid of this header, placing the I2C address where
they belong, e. g. either at bttv driver or at tvtuner.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a fix for commit 329d88da4d ("[media] media: i2c: Don't export
ir-kbd-i2c module alias") that stopped the module from being loaded
automagically.
The problems described only affect the HD-PVR, so it should not affect
other hardware; also if the module happens to be loaded, the i2c IR
part of the HD-PVR will be enabled anyway.
Fixes: 329d88da4d ("[media] media: i2c: Don't export ir-kbd-i2c module alias")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code implements the transmitter which is currently implemented
in the staging lirc_zilog driver.
The new code does not need a signal database, iow. the
haup-ir-blaster.bin firmware file is no longer needed, and the driver
does not know anything about the keycodes in that file.
Instead, the new driver can send raw IR, but the hardware is limited
to few different lengths of pulse and spaces, so it is best to use
generated IR rather than recorded IR.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two devices ids are really just one device with multiple
addresses. Probing becomes much simpler if we simply fold this into
one i2c device with two address.
Note that this breaks the lirc_zilog driver, however we will teach
ir-kbd-i2c to do what lirc_zilog does in a later commit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lirc_zilog driver only polls the device if the lirc chardev
is opened; do the same with the rc-core driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the dev_dbg dynamic infrastructure instead of rolling our own custom
debug logic.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the parent set for the rc device, the messages clearly state
that it is attached via i2c. The additional printk is unnecessary.
These are the old messages:
rc rc1: i2c IR (Hauppauge WinTV PVR-150 as /devices/virtual/rc/rc1
ir-kbd-i2c: i2c IR (Hauppauge WinTV PVR-150 detected at i2c-10/10-0071/ir0 [ivtv i2c driver #0]
Now we simply get:
rc rc1: Hauppauge WinTV PVR-150 as /devices/pci0000:00/0000:00:1e.0/0000:02:00.0/i2c-10/10-0071/rc/rc1
Note that we no longer copy the name. I've checked all call sites
to verfiy this is not a problem.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The smatch logic gets confused with the syntax used to check if the
ov9650x_read() reads succedded:
drivers/media/i2c/ov9650.c:895 __g_volatile_ctrl() error: uninitialized symbol 'reg2'.
drivers/media/i2c/ov9650.c:895 __g_volatile_ctrl() error: uninitialized symbol 'reg1'.
There's nothing wrong with the original logic, except that
it is a little more harder to review.
So, let's stick with the syntax that won't cause read
issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As smatch reported:
drivers/media/i2c/imx274.c:659 imx274_regmap_util_write_table_8() error: uninitialized symbol 'err'.
There is a bug at imx274_regmap_util_write_table_8() with causes
it to randomly return a random error if range_count is zero.
Worse than that, the logic there starts with range_count
equal to zero, and periodically resets it to zero again.
As it is a way more likely that err assumes a non-zero value,
I suspect that the chance of this code to run is very small,
so, it would be worth to review the entire function.
Anyway, clearly it shouldn't be returning error if range_count
is zero. So, let's fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If set_fmt callback is called with format->width or format->height set to
zero and HACTIVE_CNT or VACTIVE_CNT bits (respectively) in chip are zero
we will divide by zero later in this callback when we try to calculate
HSC or VSC values.
Fix this by explicitly rejecting these values.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 0b1100 value in 4 LSBs of "General Status 1" register (AFD_FMT_STAT) has
known meaning for CX2584x-series chips - it means that a SECAM signal is
currently detected by the chip.
Use this opportunity to also fix wrong binary values that were present
as comments attached to some entries in an array where
chip register -> V4L2 standard mappings are stored.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of_node_full_name() now returns only the basename, the endpoint
information printed became useless:
adv748x 4-0070: Endpoint endpoint on port 7
adv748x 4-0070: Endpoint endpoint on port 8
adv748x 4-0070: Endpoint endpoint on port 10
adv748x 4-0070: Endpoint endpoint on port 11
Restore the old behavior by using "%pOF" instead:
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11
Fixes: a7e4cfb0a7 ("of/fdt: only store the device node basename in full_name")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 'return' was missing when detecting Arbitration Lost and
calling transmit_done. With the return transmit_done could be
called a second time, confusing the CEC framework. Luckily
the Arbitration Lost condition is very rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate checks.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current implementation has to search the list of controls for the
pixel rate control, each time it is set. This can be optimised easily
by storing the ctrl pointer in the CSI/TX object, and referencing that
directly.
While at it, fix up a missing blank line also highlighted in review
comments.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mt9v032_power_on() leaves clk enabled in case of errors,
but it is not expected by its callers.
There is a similar problem in mt9v032_registered().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov7670 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sub-device for ov7670 is registered by v4l2_async_register_subdev().
So it should be unregistered by v4l2_async_unregister_subdev() instead of
v4l2_device_unregister_subdev().
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the missing MAINTAINERS entry for imx274, fix error handling in driver
probe and unregister the correct control handler in driver remove.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_async_register_subdev_sensor_common() is only provided when
CONFIG_V4L2_FWNODE is enabled, otherwise we get a link failure:
drivers/media/i2c/et8ek8/et8ek8_driver.o: In function `et8ek8_probe':
et8ek8_driver.c:(.text+0x884): undefined reference to `v4l2_async_register_subdev_sensor_common'
This adds a Kconfig 'select' statement like all the other users of
this interface have.
Fixes: d8932f38c1 ("media: et8ek8: Add support for flash and lens devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov13858 driver depends on the V4L2 fwnode, thus add that to Kconfig.
Fixes: 5fcf092e0c ("[media] ov13858: add support for OV13858 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
