Take the return value from mcasp_common_hw_param() and use that in case of
error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The use of pm_runtime in trigger() callback is not correct and it will lead
to unbalanced power.usage_count.
The only place which might need to call pm_runtime is the set_fmt callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These registers can be configured synchronously for playback and capture.
Furthermore when McASP is in master and sync mode the capture operation
needs the TX path to be configured in order to be able to provide the needed
clocks for the bus.
xxFMT and xxFMCT registers has been already configured for both TX and RX
other places in the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of
davinci_hw_common_param - for common, I2S/DIT mode settings
davinci_hw_dit_param - for DIT protocol configuration
davinci_hw_param - for I2S (and compatible protocols)
Use the following names:
mcasp_common_hw_param, mcasp_dit_hw_param and mcasp_i2s_hw_param.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make BCLK divider setting implicite in hw_params call if McASP device
is the bit clock master on the audio serial bus.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The referenced clock is used to get codec clock rate and the clock is
disabled and enabled in startup and shutdown snd_soc_ops call
backs. The change is also documented in DT bindigs document.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
cc: bcousson@baylibre.com
Signed-off-by: Mark Brown <broonie@linaro.org>
The prefix for the codec driver can be used during dual identical
codec usecases. However, dapm adds prefix twice for codec DAI widget
in snd_soc_dapm_add_route API.
This change is to avoid double prefix addition for codec DAI widget
and is needed while using identical dual codecs.
Signed-off-by: Songhee Baek <sbaek@nvidia.com>
Signed-off-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently compressed audio streams are statically routed from the /dev
to the DAI link. Some DSPs can route compressed data to multiple BE DAIs
like they do for PCM data.
Add support to allow dynamically routed compressed streams using the existing
DPCM infrastructure. This patch adds special FE versions of the compressed ops
that work out the runtime routing.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC compressed code needs to call the internal DPCM APIs in order to
dynamically route compressed data to different DAIs.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the soc generic dmaengine pcm driver allows using the defualt settings,
so the pcm->config maybe NULL.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
range_min is the lowest address in the virtual register range. This is
the first register with address 0, not the first register of page 1.
Currently all writes to page 1 are mapped to page 0, so the codec fails
to operate.
Fixes: 4d208ca429 (ASoC: tlv320aic32x4: Convert to direct regmap API usage)
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org (v3.13 if the fix misses -final)
Make it easier for generic code to work with set_sysclk() by distinguishing
between the operation not being supported and an error as is done for
other operations like set_dai_fmt()
Signed-off-by: Mark Brown <broonie@linaro.org>
soc_widget_read API returns the register data and it is possible
that a register can contain 0xffffffff. Thus, change the prototype
of soc_widget_read to return only the error code and pass the reg
data through pointer argument.
Signed-off-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Samsung dmaengine ASoC driver is used with two different dmaengine drivers.
The pl80x, which properly supports residue reporting and the pl330, which
reports that it does not support residue reporting. So there is no need to
manually set the NO_RESIDUE flag. This has the advantage that a proper (race
condition free) PCM pointer() implementation is used when the pl80x driver is
used. Also once the pl330 driver supports residue reporting the ASoC PCM driver
will automatically start using it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pl330 driver properly reports that it does not have residue reporting
support, which means the PCM dmanegine driver is able to figure this out on its
own. So there is no need to set the flag manually. Removing the flag has the
advantage that once the pl330 driver gains support for residue reporting it will
automatically be used by the generic dmaengine PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The dmaengine framework now exposes the granularity with which it is able to
report the transfer residue for a certain DMA channel. Check the granularity in
the generic dmaengine PCM driver and
a) Set the SNDRV_PCM_INFO_BATCH if the granularity is per period or worse.
b) Fallback to the (race condition prone) period counting if the driver does
not support any residue reporting.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we have two different snd_soc_platform_driver structs in the generic
dmaengine PCM driver. One for dmaengine drivers that support residue reporting
and one for those which do not. When registering the PCM component we check
whether the NO_RESIDUE flag is set or not and use the corresponding
snd_soc_platform_driver. This patch modifies the driver to only have one
snd_soc_platform_driver struct where the pointer() callback checks the
NO_RESIDUE flag at runtime. This allows us to set the NO_RESIDUE flag after the
PCM component has been registered. This becomes necessary when querying whether
the dmaengine driver supports residue reporting from the dmaengine driver itself
since the DMA channel might only be requested after the PCM component has been
registered.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's a bug that writing to the platform data directly, for it should
be constant. So just copy it before writing.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of open-coding the intersecting of two rate masks (and getting slightly
wrong for some of the corner cases) use the new snd_pcm_rate_mask_intersect()
helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SNDRV_PCM_RATE_CONTINUOUS means that all rates (possibly limited to a certain
interval) are supported. There is no need to manually set other rate bits.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
SNDRV_PCM_RATE_CONTINUOUS means that all rates (possibly limited to a certain
interval) are supported. There is no need to manually set other rate bits.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If none of the components (CODEC or CPU DAI) sets a maximum sample rate we'll
end up with the rate_max field of the runtime hardware set to 0. (Note that it
is still possible for the components to constrain the supported sample rates
using other methods, e.g. setting a list constraint) If rate_max is 0 this means
that the sound card doesn't support any rates at all, which is not the desired
result. So initialize rate_max to UINT_MAX. For symmetry reasons also set
rate_min to 0.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove asoc_simple_get_card_info macro and use snd_soc_card_set_drvdata
and snd_soc_card_get_drvdata instead.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This codec driver fails to probe because it has a higher regmap
range_max value than max_register. This patch sets the range_max to the
max_register value as described in the for struct regmap_range_cfg:
"@range_max: Address of the highest register in virtual range."
Fixes: 4d208ca429 (ASoC: tlv320aic32x4: Convert to direct regmap API usage)
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org (v3.13 if the fix misses -final)
