We only use clk_get() to get the frequency, the rest is done by
the runtime PM calls. Let's free the clock too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ba9738134 ("net: ethernet: davinci_emac: add pm_runtime support")
added support for runtime PM, but it causes issues on omap3 related devices
that actually gate the clocks:
Unhandled fault: external abort on non-linefetch (0x1008)
...
[<c04160f0>] (emac_dev_getnetstats) from [<c04d6a3c>] (dev_get_stats+0x78/0xc8)
[<c04d6a3c>] (dev_get_stats) from [<c04e9ccc>] (rtnl_fill_ifinfo+0x3b8/0x938)
[<c04e9ccc>] (rtnl_fill_ifinfo) from [<c04eade4>] (rtmsg_ifinfo+0x68/0xd8)
[<c04eade4>] (rtmsg_ifinfo) from [<c04dd35c>] (register_netdevice+0x3a0/0x4ec)
[<c04dd35c>] (register_netdevice) from [<c04dd4bc>] (register_netdev+0x14/0x24)
[<c04dd4bc>] (register_netdev) from [<c041755c>] (davinci_emac_probe+0x408/0x5c8)
[<c041755c>] (davinci_emac_probe) from [<c0396d78>] (platform_drv_probe+0x48/0xa4)
Let's fix it by moving the pm_runtime_get() call earlier, and also add it to
the emac_dev_getnetstats(). Also note that we want to use pm_runtime_get_sync()
as we don't want to have deferred_resume happen. And let's also check the
return value for pm_runtime_get_sync() as noted by Felipe Balbi <balbi@ti.com>.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On davinci_emac, we have pulse interrupts. This means that we need to
clear the EOI bits when disabling interrupts as otherwise the interrupts
keep happening. And we also need to not clear the EOI bits again when
enabling the interrupts as otherwise we will get tons of:
unexpected IRQ trap at vector 00
These errors almost certainly mean that the omap-intc.c is signaling
a spurious interrupt with the reserved irq 127 as we've seen earlier
on omap3.
Let's fix the issue by clearing the EOI bits when disabling the
interrupts. Let's also keep the comment for "Rx Threshold and Misc
interrupts are not enabled" for both enable and disable so people
are aware of this when potentially adding more support.
Note that eventually we should handle the RX and TX interrupts
separately like cpsw is now doing. However, so far I have not seen
any issues with this based on my testing, so it seems to behave a
little different compared to the cpsw that had a similar issue.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
while adding vlan in dual EMAC mode, only specific ports should be
subscribed for the vlan, else it will lead to switching mode and
if both ports connected to same switch cpsw will hung as it creates
a network loop. Fixing this by adding only specific ports in case
of dual EMAC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW is present in AM33xx, AM43xx, DRA7xx.
Updating the Kconfig to depend on ARCH_OMAP2PLUS instead of listing
all SoC's.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.
The purpose of setting the Dual MAC mode for this register is to:
"... allow packets from both ethernet ports to be written into
the FIFO without one port starving the other port."
- AM335x ARM TRM
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.
However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.
This patch should also be applied to v3.17.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove all the child devices from the system to make sure that re-insert of
cpsw module doesn't fail on child device populated by of_platform_populate().
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memories allocated with devm_* apis must not be freed with kfree apis,
so removing the kfree calls
Fixes: e194312854 ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to get the MACIDs from the am33xx SoC
control module registers which hold unique vendor MACIDs. This is only
used if of_get_mac_address() fails to get a valid mac address.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_err instead of pr_err.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
"MII_BUS_ID_SIZE" is defined in linux/phy.h which is not included in the
cpsw.h file.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ret is set 0 at this point, so jumping to that error label would result
in a return value of 0. Set ret to -ENOMEM to return a proper error
value.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend and resume in Dual EMAC, second port is not working as in
suspend/resume only the first slave netdev is closed and opened. So bring
down and up all the interfaces that are up during suspend/resume.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Dual EMAC, when both interface are up and while doing ifdown with heavy
traffic then skbs already processed by DMA from that slave emac has to be
requeued as still the other interface is up and running.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It removes the owner field updation of driver structure.
It will be automatically updated by module_platform_driver()
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW supports both rx and tx pause frames for flow control.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the interrupt resource lookup code in cpsw_probe() by the
following:
* Only look at the first member of the resource. As the driver only
works for DT-enabled platforms anyway, a resource of type
IORESOURCE_IRQ will only contain one single entry
(res->start == res->end), so there is no need for the iteration.
* Add a bounds check to avoid overflows if we are passed more than
ARRAY_SIZE(priv->irqs_table) resources.
* Assign 'ret' with the return value of devm_request_irq() so that
cpsw_probe() returns the appropriate error code.
* If devm_request_irq() fails, report the error code in the log
message.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Added a guaranteed null-terminate after call to strncpy.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
removing unused function as part of driver cleanup.`
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to view addresses added by the driver and learnt by the
hardware from ALE table via ethtool register dump interface.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to create PHYs from DT in case
if they are explicitly defined. The of_mdiobus_register() is
used for such purposes.
For backward compatibility, call of_mdiobus_register() only in case
if at least one PHY's child is defined in DT, otherwise rollback to
mdiobus_register().
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of return error on zero rx_coalesce_usecs, disable coalesce
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the debug message format. This patch changes to the
commit f160a2d0b5: net: cpmac: dynamic debug fixes
When we use pr_debug()/netdev_dbg() new lines are inserting in b/w
the values. The format when i use the printk()
These formats used in skb dump and reg dump. This functions
called from the entire code. So this will be enabled all the lines.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
before registering the the net device this code freeing net device
by using the label 'fail'
fixed by introducing an another label 'out'
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch insert proper spaces before return statement.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes to style of declarattion which follows every driver
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does the following changes
1. convert printk(KERN_DEBUG.. to netdev_dbg() if we have net_device object
or convert to dev_dbg() if we have device object.
2. convert printk(KERN_WARNING.. to netdev_warn() if we have net_device object
or convert to dev_warn() if we have device object
3. convert printk() to pr_*
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert the normal comments to networking subsystem
style comments.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the space after '#' in macro defination
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using internal 10 Mbps PHY, isolate the external PHY from MII bus.
External PHY must be kept powered up because it passes TX from tlan chip to
network.
This fixes weird link-loss problems under load with OC-2326 card at 10 Mbps.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_disable_device() is called in _suspend but there's no corresponding
pci_enable_device() in _resume.
This causes "disabling already-disabled device" warning on 2nd suspend.
Add pci_enable_device() call to _resume to fix this problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tlan_reset_adapter, we disable internal PHY when an external one is used.
On cards which use internal PHY in 10 Mbps mode, we enable it later when
setting 10 Mbps mode but it does not really work (PHY fails to reset).
Leave it enabled instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a timeout to prevent infinite loop waiting for PHY to reset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the autonegotiation poll interval from 8 seconds to 2.
This greatly reduces the time needed to detect link presence,
especially on Olicom cards at 10 Mbps (two autonegoatiations required).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess printks when the link is down.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link is lost on a card which uses internal PHY for 10 Mbit speeds,
restart autonegotiation to allow switching between 10 and 100 Mbps speeds.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM.
Byte-swap the MAC address if it's located at offset 0xF8.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
