Currently we treat intel_{dp,hdmi}->color_range as partly user
controller value (via the property) but we also change it during
.compute_config() when using the "Automatic" mode. That is a bit
confusing, so let's just change things so that we store the user
property values in intel_dp, and only change what's stored in
pipe_config during .compute_config().
There should be no functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WA for BXT A0/A1, where DDIB's HPD pin is swapped to DDIA, so enabling
DDIA HPD pin in place of DDIB.
v2: For DP, irq_port is used to determine the encoder instead of
hpd_pin and removing the edp HPD logic because port A HPD is not
present(Imre)
v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
Added hpd_pin swapping for intel_dp_init_connector, setting encoder
for PORT_A as per the WA in irq_port (Imre)
v4: Dont enable interrupt for edp, also reframe the description (Siva)
v5: Don’t check for PORT_A in intel_ddi_init to update dig_port,
instead avoid setting hpd_pin itself (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 spec TEST_CRC_COUNT is a "4 bit wrap counter which
increments each time the TEST_CRC_x_x are updated."
However if we are trying to verify the screen hasn't changed we get
same (count, crc) pair twice. Without this patch we would return
-ETIMEOUT in this case.
So, if in 6 vblanks the pair (count, crc) hasn't changed we
return it anyway instead of returning error and let test case decide
if it was right or not.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 Spec TEST_CRC_COUNT should be
"reset to 0 when TEST_SINK bit 0 = 0."
However for some strange reason when PSR is enabled in
certain platforms this is not true. At least not immediatelly.
So we face cases like this:
first get_sink_crc operation:
count: 0, crc: 000000000000
count: 1, crc: c101c101c101
returned expected crc: c101c101c101
secont get_sink_crc operation:
count: 1, crc: c101c101c101
count: 0, crc: 000000000000
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
But also the reset to 0 should be faster resulting into:
get_sink_crc operation:
count: 1, crc: c101c101c101
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
So in order to know that the second one is valid one
we need to compare the pair (count, crc) with latest (count, crc).
If the pair changed you have your valid CRC.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP spec, test counter at DP_TEST_SINK_MISC just reset to 0
when unsetting DP_TEST_SINK_START, so let's force this stop here.
But let's minimize the aux transactions and just do it when we know
it hasn't been properly stoped.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BPP bits defined in VBT should be used only on panels whose
edid version is 1.3 or older. EDID version 1.4 introduced offsets
where bpp is defined and read into display_info, hence bpp from
VBT will be used only when bpc in display_info is zero.
v2: use display_info.bpc for deciding when to use vbt_bpp (Jani)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just a preparation patch to make clear what operation we
are performing. There is no functional change on the sink crc
logic.
hsw_disable_ips has been moved a bit further in the start function
to avoid disabling ips when sink crc is not going to be started.
and to avoid goto on this function.
v2: explain why hsw_disable_ips() call place has changed.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we got to the point where we are trying to stop sink CRC
the main output of this function was already gotten properly,
so don't return the error and let userspace use the crc data.
Let's replace the errnos returns with some log messages.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now if we face any kind of error sink crc calculation
stays enabled.
So, let's give a shot and try to stop it anyway if it got enabled.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There's not much point for calculating the changes for the old
state. Instead just disable all scalers when disabling. It's
probably good enough to just disable the crtc_scaler, but just in
case there's a bug disable all scalers.
This means intel_atomic_setup_scalers is only called in the crtc
check function now, so all the transitional code can be removed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull intel drm fixes from Jani Nikula:
"Almost all of it is regression fixes all around, with cc: stable, and
then there's Ander's fix for one of the warnings you reported. We're
still working on the rest"
[ Dave is on vacation, and Jani is heading out on vacation too ]
* tag 'drm-intel-next-fixes-2015-07-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Clear pipe's pll hw state in hsw_dp_set_ddi_pll_sel()
drm/i915: fix backlight after resume on 855gm
agp/intel: Fix typo in needs_ilk_vtd_wa()
drm/i915/ppgtt: Break loop in gen8_ppgtt_clear_range failure path
drm/i915: Fix IPS related flicker
Similarly to what is done for SKL, clear the dpll_hw_state of the pipe
config in hsw_dp_set_ddi_pll_sel(), since it main contain stale values.
That can happen if a crtc that was previously driving an HDMI connector
switches to a DP connector. In that case, the wrpll field was left with
its old value, leading to warnings like the one below:
[drm:check_crtc_state [i915]] *ERROR* mismatch in dpll_hw_state.wrpll (expected 0xb035061f, found 0x00000000)
------------[ cut here ]------------
WARNING: CPU: 1 PID: 767 at drivers/gpu/drm/i915/intel_display.c:12324 check_crtc_state+0x975/0x10b0 [i915]()
pipe state doesn't match!
This regression was indroduced in
commit dd3cd74acf
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 13:34:29 2015 +0300
drm/i915: Don't overwrite (e)DP PLL selection on SKL
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
The current code tracks business across all pipes, but we're only
really interested in the one pipe DRRS is enabled on. Fairly tiny
optimization, but something I noticed while reading the code. But it
might matter a bit when e.g. showing a video or something only on the
external screen, while the panel is kept static.
Also regroup the code slightly: First compute new bitmasks, then take
appropriate actions.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
commit 2c310b9d2859863826c3688c88218d607d5dd19a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon May 18 12:28:52 2015 +0200
drm/i915: Split skl_update_scaler, v4.
It's easier to read separate functions for crtc and plane scaler state.
Changes since v1:
- Update documentation.
Changes since v2:
- Get rid of parameters to skl_update_scaler only used for traces.
This avoids needing to document the other parameters.
Changes since v3:
- Rename scaler_idx to scaler_user.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Changes for BXT - added a IS_BROXTON check to use the macro related to PPS
registers for BXT.
BXT does not have PP_DIV register. Making changes to handle this.
Second set of PPS registers have been defined but will be used when VBT
provides a selection between the 2 sets of registers.
v2:
[Jani] Added 2nd set of PPS registers and the macro
Jani's review comments
- remove reference in i915_suspend.c
- Use BXT PP macro
Squashing all PPS related patches into one.
v3: Jani's review comments addressed
- Use pp_ctl instead of pp
- ironlake_get_pp_control() is not required for BXT
- correct the use of && in the print statement
- drop the shift in the print statement
v4: Jani's comments
- modify ironlake_get_pp_control() - dont set unlock key for bxt
v5: Sonika's comments addressed
- check alignment
- move pp_ctrl_reg write (after ironlake_get_pp_control())
to !IS_BROXTON case.
- check before subtracting 1 for t11_t12
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Corrected the documentation on the intel_edp_drrs_flush and
intel_edp_drrs_invalidate.
And accordingly edp_drrs_flush function is modified to restart the idleness
detection after upclocking.
v2: Update kerneldoc
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> (v1)
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than reading out the current cdclk value use the cached value we
have tucked away in dev_priv.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BXT supports following intermediate link rates for edp:
2.16GHz, 2.43GHz, 3.24GHz, 4.32GHz.
Adding support for programming the intermediate rates.
v2: Adding clock in bxt_clk_div struct and then look for the entry with
required rate (Ville)
v3: 'clock' has the selected value, no need to use link_bw or rate_select
for selecting pll(Ville)
v4: Make bxt_dp_clk_val const and remove size (Ville)
v5: Rebased
v6: Removed setting of vco while rebasing in v5, adding it back
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Reviewed-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Cc: stable@vger.kernel.org
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The hotplug callbacks for DP and DDI effectively did nothing. Remove
them.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are plenty of hotplug related fields in struct drm_i915_private
scattered all around. Group them under one hotplug struct. Clean up
naming while at it. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit is the "sink CRC" version of:
commit 8c740dcea2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Oct 17 18:42:03 2014 -0300
drm/i915: disable IPS while getting the pipe CRCs.
For some unknown reason, when IPS gets enabled, the sink CRC changes.
Since hsw_enable_ips() doesn't really guarantee to enable IPS (it
depends on package C-states), we can't really predict if IPS is
enabled or disabled while running our CRC tests, so let's just
completely disable IPS while sink CRCs are being used.
If we find a way to make IPS not change the pipe CRC result, we may
want to fix IPS and then revert this patch (and 8c740dcea too). While
this doesn't happen, let's merge this patch, so the IGT tests relying
on sink CRCs can work properly.
This was discovered while developing a new IGT test, which will
probably be called kms_frontbuffer_tracking.
Testcase: igt/kms_frontbuffer_tracking (not on upstream IGT yet)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename dpio_lock to sb_lock to inform the reader that its primary
purpose is to protect the sideband mailbox rather than some DPIO
state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the IBX transcoder B workarounds are not working correctly.
Well, the HDMI one seems to be working somewhat, but the DP one is
definitely busted.
After a bit of experimentation it looks like the best way to make this
work is first disable the port on transcoder B, and then re-enable it
transcoder A, and immediately disable it again.
We can also clean up the code by noting that we can't be called without
a valid crtc. And also note that port A on ILK does not need the
workaround, so let's check for that one too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're always enabling enhanced framing on CPT even if the sink
doesn't support it. Fix this up by actaully looking at what the sink
tells us.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Define a TRANS_DP_PIPE_TO_PORT() to make the CPT DP .get_hw_state()
pipe readout neater.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_dp.c is a mess with all the checks for different
platform/PCH variants and ports. Try to clean it up by recognizing
the following facts:
- IVB port A, and CPT port B/C/D are always the special cases
- VLV/CHV don't have port A
- Using the same kind of logic everywhere makes things much easier to
parse
So let's move the IVB port A and PCH port B/C/D checks to be done first,
and let the other cases fall through, and always check for these things
using the same logic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Be in line with other features that we have.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the following commit, the place where the contents of dpll_hw_state
in crtc_state where zeroed was changed. Prior to that commit, it
happened when the new state was allocated, but now that happens just
before the call the .crtc_compute_clock() hook. The DP code for SKL,
however, sets up the (private) PLL in the encoder compute config
function that has already run by the time that memset() is reached,
causing the previous value to be lost.
This patch fixes the issue by moving the memset() down the call chain,
so that it is only called if the values in dpll_hw_state are going to be
updated.
commit 4978cc93d9
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90462
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reported-and-tested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is an extra semi-colon on the if statement so the debug output
always says "Failed to write EDID checksum" even when it didn't fail.
Fixes: 559be30cb7 ('drm/i915: Implement the intel_dp_autotest_edid function for DP EDID complaince tests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVWh3TAAoJEHm+PkMAQRiG/kwH/2c9irodp2+M9OUnX2bfsBb6
LnChiDpvkF5BB8jhP6d/XmvPp4NJzAbTxByhjdfb2E2HkorCUHCOIn2tI1TE2pUs
2qjkOVH+XCzoV0goGtQjzK1ht8f2IrtlDiEjyRekK5cJHzhggb22QPtWL4npyd0O
reDmG2jsRaF9POr9uLSFEv4CEnkksmRLUU0vuQX0TZeCJ41O7TXrkN/wKrLZ5mj4
IWpqXQaSlrffq/T5HnVbXBxk3/T8QmhrIoppiMpV1mUVj0uTqlFRNi5qwT2Nit1h
FVljWI4+WgOk3bf7fUlp+ahopjkTgu+GuXkiRP/pdgWNQO0cxCWSAzSndAlIIAE=
=uOoJ
-----END PGP SIGNATURE-----
Backmerge v4.1-rc4 into into drm-next
We picked up a silent conflict in amdkfd with drm-fixes and drm-next,
backmerge v4.1-rc5 and fix the conflicts
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/drm_irq.c
Currently vlv_wait_port_ready() waits for all four lanes on the
appropriate channel. This no longer works on CHV when the unused
lanes may be power gated. So pass in a mask of lanes that the
caller is expecting to be ready.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also treat it as a proper boolean.
Cc: Todd Previte <tprevite@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Set up the chv display PHY lane stagger registers according to
"Programming Guide for 1273 CHV eDP/DP/HDMI Display PHY" v1.04
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Renaming gen9_rates to skl_rates because other platforms may have different
supported rates.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updates the EDID compliance test function to perform the analyze and react to
the EDID data read as a result of a hot plug event. The results of this
analysis are handed off to userspace so that the userspace app can set the
display mode appropriately for the test result/response.
The compliance_test_active flag now appears at the end of the individual
test handling functions. This is so that the kernel-side operations can
be completed without the risk of interruption from the userspace app
that is polling on that flag.
V2:
- Addressed mailing list feedback
- Removed excess debug messages
- Removed extraneous comments
- Fixed formatting issues (line length > 80)
- Updated the debug message in compute_edid_checksum to output hex values
instead of decimal
V3:
- Addressed more list feedback
- Added the test_active flag to the autotest function
- Removed test_active flag from handler
- Added failsafe check on the compliance test active flag
at the end of the test handler
- Fixed checkpatch.pl issues
V4:
- Removed the checksum computation function and its use as it has been
rendered superfluous by changes to the core DRM EDID functions
- Updated to use the raw header corruption detection mechanism
- Moved the declaration of the test_data variable here
V5:
- Update test active flag variable name to match the change in the
first patch of the series.
- Relocated the test active flag declaration and initialization
to this patch
V6:
- Updated to use the new flag for raw EDID header corruption
- Removed the extra EDID read from the autotest function
- Added the edid_checksum variable to struct intel_dp so that the
autotest function can write it to the sink device
- Moved the update to the hpd_pulse function to another patch
- Removed extraneous constants
V7:
- Fixed erroneous placement of the checksum assignment. In some cases
such as when the EDID read fails and is NULL, this causes a NULL ptr
dereference in the kernel. Bad news. Fixed now.
V8:
- Updated to support the kfree() on the EDID data added previously
V9:
- Updated for the long_hpd flag propagation
V10:
- Updated to use actual checksum from the EDID read that occurs during
normal hot plug path execution
- Removed variables from intel_dp struct that are no longer needed
- Updated the patch subject to more closely match the nature and contents
of the patch
- Fixed formatting problem (long line)
V11:
- Removed extra debug messages
- Updated comments to be more informative
- Removed extra variable
V12:
- Removed the 4 bit offset of the resolution setting in compliance data
- Changed to DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER
Signed-off-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This provides an option to override the value set by VBT
for selecting edp Vswing Pre-emph setting table.
v2: Adding comment about this being a temporary workaround and
making the parameter read-only (Jani)
v3: Changing mode to 0400 instead of 0 (Jani)
https://bugs.freedesktop.org/show_bug.cgi?id=89554
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds DP link training optimization by reusing the
previously trained values.
v2:
- rebase
V3:
- rebase
V4:
- when HPD long pulse is received, the flag is cleared
that indicates if DP link training is required or not
(based on Sivakumar's comment)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a first of series patches that optimize DP link
training. The first patch is for eDP only where we reuse
the previously trained link training values from cache
i.e. voltage swing and pre-emphasis levels.
In case we are not able to train the link by reusing
the known values, the link training parameters are set
to zero and training is restarted.
V2:
- flag that indicates if DP link is trained and valid
renamed from 'link_trained' to 'train_set_valid'
- removed routine 'intel_dp_reuse_link_train'
V3:
- rebased against the latest drm-intel-nightly
V4:
- removed HPD long pulse handling for eDP case to clear the
flag that indicates to reuse the current link training
parameters. (based on Sivakumar's comment)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[danvet: s/DP/eDP/ in subject to make scope clear.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to changes in the driver and to support Displayport compliance testing,
the test request and sink IRQ logic has been relocated from
intel_dp_check_link_status to intel_dp_detect. This is because the bulk of the
compliance tests that set the TEST_REQUEST bit in the DEVICE_IRQ field of the
DPCD issue a long pulse / hot plug event to signify the start of the test.
Currently, for a long pulse, intel_dp_check_link_status is not called for a
long HPD pulse, so if test requests come in, they cannot be detected by the
driver.
Once located in the intel_dp_detect, in the regular hot plug event path,
proper detection of Displayport compliance test requests occurs which then
invokes the test handler to support them. Additionally, this places compliance
testing in the normal operational paths, eliminating as much special case code
as possible.
The only change in intel_dp_check_link_status with this patch is that when
the IRQ is the result of a test request from the sink, the test handler is not
invoked during the short pulse path. Short pulse test requests are for a
particular variety of tests (mainly link training) that will be implemented
in the future. Once those tests are available, the test request handler will
be called from here as well.
V2:
- Rewored the commit message to be more clear about the content and intent
of this patch
- Restore IRQ detection logic to intel_dp_check_link_status(). Continue to
detect and clear sink IRQs in the short pulse case. Ignore test requests
in the short pulses for now since they are for future test implementations.
Signed-off-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
