Per i.MX7D Document Number: IMX7DCEC Rev. 6, 03/2019,
there are only consumer/industrial parts, and 1.2GHz
is only support in consumer parts.
So exclude automotive from 792/996MHz/1.2GHz and exclude
industrial from 1.2GHz.
Fixes: d7bfba7296 ("ARM: dts: imx7d: Update cpufreq OPP table")
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following warning is seen when building with W=1:
arch/arm/boot/dts/imx7s.dtsi:551.39-553.7: Warning (unique_unit_address): /soc/aips-bus@30000000/ocotp-ctrl@30350000/temp-grade@10: duplicate unit-address (also used in node /soc/aips-bus@30000000/ocotp-ctrl@30350000/speed-grade@10)
Since temp-grade and speed-grade point to the same node, replace them by
a single one to avoid the duplicate unit-address warning.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties "#cooling-cells" should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in the
CPU node it is trying to bring up, so that it can register a cooling
device.
Add such missing properties.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "opp-suspend" property for i.MX7D to make sure system
suspend with max available opp.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 800MHz opp speed grading fuse mask should be 0xd instead
of 0xf according to fuse map definition:
SPEED_GRADING[1:0] MHz
00 800
01 500
10 1000
11 1200
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use a space before and after assignment operator to have consistent
style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest docs imx7d chips can go from 800 to 1200 mhz.
Maximum frequency is determined from two speed grading bits present in
OCOTP fuses at same location as other imx chips.
Also update to "typical" voltages from latest datasheet, 25mv higher
than current dts.
All imx7s parts are still fixed at 800mhz
Based on:
* IMX7DCEC Rev. 6, 03/2019
* IMX7SCEC Rev. 6, 03/2019
* IMX7DRM Rev. 1, 01/2018 Page 1102
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX7D comes with 4 viewports, so configure PCIE node accordingly so
that the driver won't assume we only have 2.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the PHY as a new node. The PCI-e controller node gains a
phandle property that points to it.
There isn't yet any code in the kernel that uses this device's
registers, but it will be added for a PCIe PLL erratum workaround.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The GIC_CPU_MASK_SIMPLE() macro should take as its argument the actual
number of CPU cores the interrupt controller is wired to.
i.MX7S contains a single Cortex-A7, hence the second interrupt specifier
cell for Private Peripheral Interrupts should use "GIC_CPU_MASK_SIMPLE(1)".
Likewise, i.MX7D contains two Cortex-A7 cores, so it should use
"GIC_CPU_MASK_SIMPLE(2)" instead.
Tested on a imx7s-warp.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are close to 800 indivudal changesets in this branch again, which
feels like a lot. There are particularly many changes for the NVIDIA
Tegra platform this time, in fact more than it has seen in the two years
since the v4.9 merge window. Aside from this, it's been fairly normal,
with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi,
Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5
is a minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core
Marvell Armada 8040 network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in
the BMC.
NXP i.MX usually sees a lot of new boards each release. This time there
we only add one minor variant: ConnectCore 6UL SBC Pro uses the same
SoM design as the ConnectCore 6UL SBC Express added later. However,
there is a new chip, the i.MX6ULZ, which is an even smaller variant
of the i.MX6ULL, with features removed. There is also support for the
reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute module
based on bcm2837, it was launched in early 2017 but only now added to
the kernel, both as 32-bit and as 64-bit files, as we tend to do for
Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time
are:
Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana
Pi M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit
Asus Tinker board, the model 'S' based on rk3288, and three now
boards based on the popular RK3399 chip:
ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
Rock960: https://www.96boards.org/product/rock960/
RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and
the RK3399 is the same chip used in several Chromebooks. Finally,
we get support for the PX30 (aka rk3326) chip, which is based on the
low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board
is supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based
on the MT7622 WiFi router platform, and the first product I've seen with
a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2),
another quad-core Cortex-A53 SoC, and its evaluation platform.
On the 32-bit side, we gain support for an actual end-user product,
the Endless Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform. This
chip is commonly known as the Snapdragon 835, and is used in high-end
phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the previously
added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB
Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing files,
the only board that gets added is the Toradex Colibri T20 on Colibri
Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the (formerly
Marvell) Berlin line of set-top-box chips used e.g. in the various Google
Chromecast. Only the .dtsi gets added at this point, no actual machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yaED
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
This is required for the imx pci driver to send the PME_Turn_Off TLP.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 1c86c9dd82.
That commit followed the reference manual but unfortunately the imx7d
manual is incorrect.
Tested with ath9k pcie card and confirmed internally.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 1c86c9dd82 ("ARM: dts: imx7d: Invert legacy PCI irq mapping")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit b97872d4eb ("ARM: dts: imx: Add missing OPP properties for CPUs")
added "operating-points" property for all CPUs, but i.MX7D already has
"operating-points-v2" property on both CPUs, so no need to add
"operating-points" property again, this patch removes it.
Fixes: b97872d4eb ("ARM: dts: imx: Add missing OPP properties for CPUs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like clocks, supply, clock latency) as
well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As always, a large number of DT updates. Too many to enumerate them all,
but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some set
top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other on-chip
ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current high-end
mobile SoCs.
It's great to see mainline support for it. So far, you
can't do much with it, since a lot of peripherals are not yet in the
DTs but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC upstream if
the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive entertainment-targeted
SoC. Currently only one Cortex-A53 CPU is enabled, we are eagerly
awaiting more. So far, basic drivers such as serial, gpios, PMU and
ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and ethernet
enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions might
not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support
-----BEGIN PGP SIGNATURE-----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=jLvk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
ENET "ipg" clock should be IMX7D_ENETx_IPG_ROOT_CLK
rather than IMX7D_ENET_AXI_ROOT_CLK which is for ENET bus
clock.
Based on Andy Duan's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch uses "operating-points-v2" instead of
"operating-points" to be more fit with cpufreq-dt
driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move usbphynop1, usbphynop2, usbhypnop3, replicator and timer and nodes
from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/replicator missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop1 missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop3 missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop2 missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in i.MX dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7s/imx7d has the ptp interrupt newly added as well.
For imx7, "int0" is the interrupt for queue 0 and ENET_MII
"int1" is for queue 1
"int2" is for queue 2
For imx6sx, "int0" handles all 3 queues and ENET_MII
And of course, the "pps" interrupt is for the PTP_CLOCK_PPS interrupts
This will help document what each interrupt does.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to i.MX7D reference manual (Rev. 0.1, table 7-1, page 1221)
legacy PCI interrupt mapping is as follows:
- PCIE INT A is IRQ 122
- PCIE INT B is IRQ 123
- PCIE INT C is IRQ 124
- PCIE INT D is IRQ 125
Invert the mapping information in corresponding DT node to reflect
that.
Cc: yurovsky@gmail.com
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Fixes: a816d5750e ("ARM: dts: imx7d: Add node for PCIe controller")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only i.MX 7Dual SoC supports CPU frequencies of up to 1GHz. The i.MX
7Solo can run with up to 800MHz and does so without making use of DVFS
usually. While the device tree clearly specified a too fast operating
point for i.MX 7Solo, the kernel did not used it in practise so far
because the CPUfreq driver does not get loaded on i.MX 7Solo devices
(since the fsl,imx7s compatible string is not in the list of devices
making use of the cpufreq-dt driver...).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since we have a SoC level node we should make use of it and have
all nodes which are within the SoC, inside that node. This also
saves an extra interrupt-parent properties. While at it, also
order the Coresight nodes according to register addresses.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7Solo implements a subset of features available on
i.MX 7Dual. Recreate imx7s.dtsi as the base device tree for
i.MX 7Dual boards. The i.MX 7Dual's additional features over
i.MX 7Solo are:
- Second Cortex-A7 core
- Second Gigabit Ethernet controller
- EPD (Electronc Paper Display, not yet part of the device tree)
- PCIe (not yet part of the device tree)
- Additional USB2.0 OTG controller
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7 series currently consists of two SoCs: i.MX 7Solo and
7Dual. The former has a subset of features of the latter, hence
use imx7s.dtsi as the new base device tree. To keep diffstat nice,
just move imx7d.dtsi to imx7s.dtsi temporarily and recreate
imx7d.dtsi in a second commit.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Building with W=1 option leads to several warnings like:
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property
Fix them by removing the unneeded unit-addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the device nodes for the i.MX7 FlexCAN buses.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the device node for the i.MX7 eLCDIF interface.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since uboot v2016.01-rc2, which supported basic psci for i.mx7d.
So imx7d's second core can be enabled by psci.
Without arch timer, every timer event will be boardcasted to each core.
arch timer has local timer irq for each core.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As on i.MX7D, we using a virtual arm clk for CPU frequency
scaling, so correct the clocks info used by the cpufreq driver.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
Add device tree node to support iomuxc-lpsr controller, fsl,input-sel
phandle allows to get input select register base address which is
shared from main iomuxc controller.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The UART2 memory space starts at address 0x30890000 (UART2_URXD).
Fix it so that UART2 can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: 9496734502 ("ARM: dts: add imx7d soc dtsi file")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change SNVS rtc to syscon interface.
Enable onoff key and power off function.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d intergrates the unique display controller for EPD panel, pixel engines
and graphics engines to make it a ideal solution for EPD based devices such
as eReader, Signage, as well as any application rely on the bistable charactersic
of the EPD panel.
imx7d include two ARM Cortex A7 Core and one Cortex-M4 core.
Included Main Peripheral
- DDR3\LP-DDR2
- GPMI\BCH\APBH DMA(NAND flash support)
- QSPI
- WEIM Nor
- LCDIF\MIPI DSI
- CSI\MIPI CSI
- EPDC
- PCIe RC\EP
- USB OTG\Host
- CAN x2
- I2C x4
- SIMv2 x2
- ENET -x2
- uSDHC x3
- eCSPI x1
- PWM x4
- OCOTP (fuse)
- GPT x4
- WDOG x4
- Flex Timer x2
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
