Add capability to control the auto bkops during suspend.
If host explicitly enables the auto bkops (background operation) on device
then only device would perform the bkops on its own. If auto bkops is not
enabled explicitly and if the device reaches to state where it must do
background operation, device would raise the urgent bkops exception event
to host and then host will enable the auto bkops on device. This patch
adds the option to choose whether auto bkops should be enabled during
runtime suspend or not. Since we don't want to keep the device active to
perform the non critical bkops, host will enable urgent bkops only.
Keep auto-bkops enabled after resume if urgent bkops needed.
If device bkops status shows that its in critical need of executing
background operations, host should allow the device to continue doing
background operations.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The clocks for UFS device will be managed by generic DVFS (Dynamic
Voltage and Frequency Scaling) framework within kernel. This devfreq
framework works with different governors to scale the clocks. By default,
UFS devices uses simple_ondemand governor which scales the clocks up if
the load is more than upthreshold and scales down if the load is less than
downthreshold.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The UFS controller clocks can be gated after certain period of
inactivity, which is typically less than runtime suspend timeout.
In addition to clocks the link will also be put into Hibern8 mode
to save more power.
The clock gating can be turned on by enabling the capability
UFSHCD_CAP_CLK_GATING. To enable entering into Hibern8 mode as part of
clock gating, set the capability UFSHCD_CAP_HIBERN8_WITH_CLK_GATING.
The tracing events for clock gating can be enabled through debugfs as:
echo 1 > /sys/kernel/debug/tracing/events/ufs/ufshcd_clk_gating/enable
cat /sys/kernel/debug/tracing/trace_pipe
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Sometimes, the device shall report its maximum power and speed
capabilities, but we might not wish to configure it to use those
maximum capabilities.
This change adds support for the vendor specific host driver to
implement power change notify callback.
To enable configuring different power modes (number of lanes,
gear number and fast/slow modes) it is necessary to split the
configuration stage from the stage that reads the device max power mode.
In addition, it is not required to read the configuration more than
once, thus the configuration is stored after reading it once.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for UFS device and UniPro link power management
during runtime/system PM.
Main idea is to define multiple UFS low power levels based on UFS device
and UFS link power states. This would allow any specific platform or pci
driver to choose the best suited low power level during runtime and
system suspend based on their power goals.
bkops handlig:
To put the UFS device in sleep state when bkops is disabled, first query
the bkops status from the device and enable bkops on device only if
device needs time to perform the bkops.
START_STOP handling:
Before sending START_STOP_UNIT to the device well-known logical unit
(w-lun) to make sure that the device w-lun unit attention condition is
cleared.
Write protection:
UFS device specification allows LUs to be write protected, either
permanently or power on write protected. If any LU is power on write
protected and if the card is power cycled (by powering off VCCQ and/or
VCC rails), LU's write protect status would be lost. So this means those
LUs can be written now. To ensures that UFS device is power cycled only
if the power on protect is not set for any of the LUs, check if power on
write protect is set and if device is in sleep/power-off state & link in
inactive state (Hibern8 or OFF state).
If none of the Logical Units on UFS device is power on write protected
then all UFS device power rails (VCC, VCCQ & VCCQ2) can be turned off if
UFS device is in power-off state and UFS link is in OFF state. But current
implementation would disable all device power rails even if UFS link is
not in OFF state.
Low power mode:
If UFS link is in OFF state then UFS host controller can be power collapsed
to avoid leakage current from it. Note that if UFS host controller is power
collapsed, full UFS reinitialization will be required on resume to
re-establish the link between host and device.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS device may have standard LUs and LUN id could be from 0x00 to 0x7F.
UFS device specification use "Peripheral Device Addressing Format"
(SCSI SAM-5) for standard LUs.
UFS device may also have the Well Known LUs (also referred as W-LU) which
again could be from 0x00 to 0x7F. For W-LUs, UFS device specification only
allows the "Extended Addressing Format" (SCSI SAM-5) which means the W-LUNs
would start from 0xC100 onwards.
This means max. LUN number reported from UFS device could be 0xC17F hence
this patch advertise the "max_lun" as 0xC17F which will allow SCSI mid
layer to detect the W-LUs as well.
But once the W-LUs are detected, UFSHCD driver may get the commands with
SCSI LUN id upto 0xC17F but UPIU LUN id field is only 8-bit wide so it
requires the mapping of SCSI LUN id to UPIU LUN id. This patch also add
support for this mapping.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS device specification requires the UFS devices to support 4 well known
logical units:
"REPORT_LUNS" (address: 01h)
"UFS Device" (address: 50h)
"RPMB" (address: 44h)
"BOOT" (address: 30h)
UFS device's power management needs to be controlled by "POWER CONDITION"
field of SSU (START STOP UNIT) command. But this "power condition" field
will take effect only when its sent to "UFS device" well known logical unit
hence we require the scsi_device instance to represent this logical unit in
order for the UFS host driver to send the SSU command for power management.
We also require the scsi_device instance for "RPMB" (Replay Protected
Memory Block) LU so user space process can control this LU. User space may
also want to have access to BOOT LU.
This patch adds the scsi device instances for each of all well known LUs
(except "REPORT LUNS" LU).
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The maximum power consumption in active is determined by bActiveICCLevel.
The configuration is done by reading max current supported by the
regulators connected to VCC, VCCQ and VCCQ2 rails on the boards, and
reading the current consumption levels from the device for each rails
(vcc/vccq/vccq2) using power descriptor.
We configure the bActiveICCLevel attribute, with the max value that
correspond to the minimum-of(VCC-current-level,VCCQ-current-level,
VCCQ2-current-level).
In order to minimize resume latency, pre-fetch icc levels and reference
clock during initialization and avoid reading them each link startup
during resume.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In ->hce_enable_notify() callback the vendor specific initialization
may carry out additional DME configuration using UIC commands and
hence the UIC command completion interrupt enable bit should be set
before the post reset notification.
Add retries if the link-startup fails. This is required since due to
hardware timing issues, the Uni-Pro link-startup might fail. The UFS
HCI recovery procedure contradicts the Uni-Pro sequence. The UFS HCI
specifies to resend DME_LINKSTARTUP command after IS.ULLS (link-lost
interrupt) is received. The Uni-Pro specifies that if link-startup
fails the link is in "down" state. The link-lost is indicated to the
DME user only when the link is up. Hence, the UFS HCI recovery procedure
of waiting for IS.ULLS and retrying link-startup may not work properly.
At the end, if detection fails, power off (disable clocks, regulators,
phy) if the UFS device detection fails. This saves power while UFS device
is not embedded into the system.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently reading query descriptor is more tightened to each
descriptor type. This patch generalize the approach and allows
reading any parameter from any query descriptor.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add the support for voting of the regulator powering the
host controller logic.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add generic clock initialization support for UFSHCD platform
driver. The clock info is read from device tree using standard
clock bindings. A generic max-clock-frequency-hz property is
defined to save information on maximum operating clock frequency
the h/w supports.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS devices are powered by at most three external power supplies -
- VCC - The flash memory core power supply, 2.7V to 3.6V or 1.70V to 1.95V
- VCCQ - The controller and I/O power supply, 1.1V to 1.3V
- VCCQ2 - Secondary controller and/or I/O power supply, 1.65V to 1.95V
For some devices VCCQ or VCCQ2 are optional as they can be
generated using internal LDO inside the UFS device.
Add DT bindings for voltage regulators that can be controlled
from host driver.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some vendor specific controller versions might need to configure
vendor specific - registers, clocks, voltage regulators etc. to
initialize the host controller UTP layer and Uni-Pro stack.
Provide some common initialization operations that can be used
to configure vendor specifics. The methods can be extended in
future, for example, for power mode transitions.
The operations are vendor/board specific and hence determined with
the help of compatible property in device tree.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If LLD has added scsi device (by calling scsi_add_device) before scheduling
async scsi_scan_host then scsi_finish_async_scan() will end up calling
scsi_sysfs_add_sdev for scsi device which was already added by LLD.
This patch fixes this issue by skipping the call to scsi_sysfs_add_sdev()
if it's already visible to rest of the kernel.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some devices may respond with wrong type for well-known logical units.
This patch forces well-known type for devices which doesn't report it
correct.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A set of flags introduced in the block layer enable better control over
how protection information is handled. These flags are useful for both
error injection and data recovery purposes. Checking can be enabled and
disabled for controller and disk, and the guard tag format is now a
per-I/O property.
Update sd_protect_op to communicate the relevant information to the
low-level device driver via a set of flags in scsi_cmnd.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A deadlock has been reported when the completion
of SCSI commands (simulated by a timer) was surprised
by a module removal. This patch removes one half of
the offending locks around timer deletions. This fix
is applied both to stop_all_queued() which is were
the deadlock was discovered and stop_queued_cmnd()
which has very similar logic.
This patch should be applied both to the lk 3.17 tree
and Christoph's drivers-for-3.18 tree.
Tested-and-reported-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Dan Carpenter found a issue where be2iscsi would copy the ip
from userspace to the driver buffer before checking the len
of the data being copied:
http://marc.info/?l=linux-scsi&m=140982651504251&w=2
This patch just has us only copy what we the driver buffer
can support.
Cc: <stable@vger.kernel.org>
Tested-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This just has iscsi_tcp support ISCSI_PARAM_LOCAL_PORT which
exports the local port being used by the iscsi connection.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump the driver version
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In the reboot/shutdown path, workqueue was destroyed after the
adapter resource were freed. The task associated with workqueue
was getting executed after resources were freed. This lead to
kernel panic.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The uses of "rcu_assign_pointer()" are NULLing out the pointers.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
add support for 20 Gbit and 40 Gbit links
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The T10 Protection Information format is also used by some devices that
do not go through the SCSI layer (virtual block devices, NVMe). Relocate
the relevant functions to a block layer library that can be used without
involving SCSI.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make the choice of checksum a per-I/O property by introducing a flag
that can be inspected by the SCSI layer. There are several reasons for
this:
1. It allows us to switch choice of checksum without unloading and
reloading the HBA driver.
2. During error recovery we need to be able to tell the HBA that
checksums read from disk should not be verified and converted to IP
checksums.
3. For error injection purposes we need to be able to write a bad guard
tag to storage. Since the storage device only supports T10 CRC we
need to be able to disable IP checksum conversion on the HBA.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Move flags affecting the integrity code out of the bio bi_flags and into
the block integrity payload.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
So far we have relied on the app tag size to determine whether a disk
has been formatted with T10 protection information or not. However, not
all target devices provide application tag storage.
Add a flag to the block integrity profile that indicates whether the
disk has been formatted with protection information.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of the "operate" parameter we pass in a seed value and a pointer
to a function that can be used to process the integrity metadata. The
generation function is changed to have a return value to fit into this
scheme.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The protection interval is not necessarily tied to the logical block
size of a block device. Stop using the terms "sector" and "sectors".
Going forward we will use the term "seed" to describe the initial
reference tag value for a given I/O. "Interval" will be used to describe
the portion of the data buffer that a given piece of protection
information is associated with.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
None of the filesystems appear interested in using the integrity tagging
feature. Potentially because very few storage devices actually permit
using the application tag space.
Remove the tagging functions.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For commands like REQ_COPY we need a way to pass extra information along
with each bio. Like integrity metadata this information must be
available at the bottom of the stack so bi_private does not suffice.
Rename the existing bi_integrity field to bi_special and make it a union
so we can have different bio extensions for each class of command.
We previously used bi_integrity != NULL as a way to identify whether a
bio had integrity metadata or not. Introduce a REQ_INTEGRITY to be the
indicator now that bi_special can contain different things.
In addition, bio_integrity(bio) will now return a pointer to the
integrity payload (when applicable).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix a typo in the IPR_IOASC_HW_CMD_FAILED declaration. Based on a patch
from Wen Xiong <wenxiong@linux.vnet.ibm.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Through the qla target code, the qlt_send_term_exchange() routine
is used in various different places to cleanup an exchange. For the
case of IOCB request queue is full, the exchange is left unhandled/
dangling. Existing code does not have re-try logic to cleanup the
exchange. This patch add retry logic to cleanup the exchange before
letting new commands through.
For the case of FW running out of exchanges, driver need to reply
SAM_STAT_BUSY to the initiators. This patch add a pending queue
for the busy reply in case IOCB queue is unable to handle the cmd.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
ABTS path takes path similar to regular task management, but
reset_count was not initialized when allocating mcmd causing
the response to get dropped in qlt_xmit_tm_rsp. Fix this by
initializing reset_count correctly.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A chip reset can occur after driver submits command to the stack. Abort
command processing if a chip reset has occurred or in progress when you
get a follow up for a command.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
tcm_qla2xxx_get_task_tag incorrectly assume command is
qla_tgt_cmd. Add check to see if it's a scsi cmd or
task mgmt command.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Sequence level error recovery (aka FC Tape) is not really required
for disk devices. On heavily loaded system, with slow turn around,
a bunch of status enquiries using REC puts additional burden to the
target, so just turn off SLER by default.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Turning logging bits for target mode ON dumps quite a lot verbose
messages, remove those and change some of the IO path logging to
use IO bits.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch is to fix regression added by commit id
51a07f8464.
When allocating memory for new session original patch does
not assign vha to op->vha resulting into NULL pointer
access during qlt_create_sess_from_atio().
Cc: <stable@vger.kernel.org>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If we fail to load one of the segments of firmware fail the operation
instead of trying to continue which will lead to a system crash since
the pointers to the next segment will not be updated correctly.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Disable the PCI device during shutdown to prevent any races with
other PCI code such as the AER handling code.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For FA-WWPN capable device, ISP2031 and ISP27XX, when loop
dead is detected by a driver, restore WWPN from NVRAM.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Parse the retry delay timer field from the FCP response data and if:
- It is not zero
- The SCSI status is busy or queue full
return SCSI_MLQUEUE_TARGET_BUSY for the number of milliseconds specified
in the retry delay timer field.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Nameserver data on FC switch is not refreshed when
qla2xxx driver is unloaded. Disabling laser for
ISP2031 will force FC switch to rescan ports and
clear fdmi entries from Nameserver.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Declaration error of mb array in qla2x00_iidma_fcport cause data
to be written beyond the array. This ends up causing stack corruption.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the D-port (diagnostic port) fabric switch feature.
(Fabric Switch initiates loopback style port testing)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the FA-WWN (fabric assigned wwn) fabric switch feature.
(Fabric Assigned World Wide Port Name)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the FDMI-2 fabric switch feature.
Since FDMI-2 uses code from FDMI-1, some of the existing code
needed to be repaired to prevent fields from being overflowed.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Semaphore register does not exist for ISPFx00.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Call scnprintf() instead of snprintf() since the latter may return
an incorrect count in cases where the write is truncated to fit.
scnprintf() returns the count of what was actually written;
snprintf() returns the count of what would have been written.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When creating request/response queues from qla25xx_setup_mode(),
the shadow index register pointers were not being initialized
to point at the registers.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since the entry call array is sorted in order of entry type opcode,
the search can be terminated as soon as the search key is exceeded.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a call to pci_set_master(...) missing in the previous
patch "hpsa: refine the pci enable/disable handling".
Found thanks to Rob Elliot.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Failing Device information are logged when IOA firmware detected these
illegal request such as IOA firmware doesn't support inquiry with page
code 2. The patch fixes the issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move PCI_VENDOR_ID_VMWARE from device-specific files to pci_ids.h.
It is useful to always have access to it, especially when accessing
subsystem_vendor_id on emulated devices.
[bhelgaas: keep pci_ids.h sorted and use lower-case hex]
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This function is only called with a spin_lock held and IRQs disabled.
The allocation is not allowed to sleep and NOIO is not sufficient, it
has to be ATOMIC.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Introduces the Xen pvSCSI frontend. With pvSCSI it is possible for a
Xen domU to issue SCSI commands to a SCSI LUN assigned to that
domU. The SCSI commands are passed to the pvSCSI backend in a driver
domain (usually Dom0) which is owner of the physical device. This
allows e.g. to use SCSI tape drives in a Xen domU.
The code is taken from the pvSCSI implementation in Xen done by
Fujitsu based on Linux kernel 2.6.18.
Changes from the original version are:
- port to upstream kernel
- put all code in just one source file
- move module to appropriate location in kernel tree
- adapt to Linux style guide
- some minor code simplifications
- replace constants with defines
- remove not used defines
- add support for larger SG lists by putting them in a granted page
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Pull networking fixes from David Miller:
1) If the user gives us a msg_namelen of 0, don't try to interpret
anything pointed to by msg_name. From Ani Sinha.
2) Fix some bnx2i/bnx2fc randconfig compilation errors.
The gist of the issue is that we firstly have drivers that span both
SCSI and networking. And at the top of that chain of dependencies
we have things like SCSI_FC_ATTRS and SCSI_NETLINK which are
selected.
But since select is a sledgehammer and ignores dependencies,
everything to select's SCSI_FC_ATTRS and/or SCSI_NETLINK has to also
explicitly select their dependencies and so on and so forth.
Generally speaking 'select' is supposed to only be used for child
nodes, those which have no dependencies of their own. And this
whole chain of dependencies in the scsi layer violates that rather
strongly.
So just make SCSI_NETLINK depend upon it's dependencies, and so on
and so forth for the things selecting it (either directly or
indirectly).
From Anish Bhatt and Randy Dunlap.
3) Fix generation of blackhole routes in IPSEC, from Steffen Klassert.
4) Actually notice netdev feature changes in rtl_open() code, from
Hayes Wang.
5) Fix divide by zero in bond enslaving, from Nikolay Aleksandrov.
6) Missing memory barrier in sunvnet driver, from David Stevens.
7) Don't leave anycast addresses around when ipv6 interface is
destroyed, from Sabrina Dubroca.
8) Don't call efx_{arch}_filter_sync_rx_mode before addr_list_lock is
initialized in SFC driver, from Edward Cree.
9) Fix missing DMA error checking in 3c59x, from Neal Horman.
10) Openvswitch doesn't emit OVS_FLOW_CMD_NEW notifications accidently,
fix from Samuel Gauthier.
11) pch_gbe needs to select NET_PTP_CLASSIFY otherwise we can get a
build error.
12) Fix macvlan regression wherein we stopped emitting
broadcast/multicast frames over software devices. From Nicolas
Dichtel.
13) Fix infiniband bug due to unintended overflow of skb->cb[], from
Eric Dumazet. And add an assertion so this doesn't happen again.
14) dm9000_parse_dt() should return error pointers, not NULL. From
Tobias Klauser.
15) IP tunneling code uses this_cpu_ptr() in preemptible contexts, fix
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
net: bcmgenet: call bcmgenet_dma_teardown in bcmgenet_fini_dma
net: bcmgenet: fix TX reclaim accounting for fragments
ipv4: do not use this_cpu_ptr() in preemptible context
dm9000: Return an ERR_PTR() in all error conditions of dm9000_parse_dt()
r8169: fix an if condition
r8152: disable ALDPS
ipoib: validate struct ipoib_cb size
net: sched: shrink struct qdisc_skb_cb to 28 bytes
tg3: Work around HW/FW limitations with vlan encapsulated frames
macvlan: allow to enqueue broadcast pkt on virtual device
pch_gbe: 'select' NET_PTP_CLASSIFY.
scsi: Use 'depends' with LIBFC instead of 'select'.
openvswitch: restore OVS_FLOW_CMD_NEW notifications
genetlink: add function genl_has_listeners()
lib: rhashtable: remove second linux/log2.h inclusion
net: allow macvlans to move to net namespace
3c59x: Fix bad offset spec in skb_frag_dma_map
3c59x: Add dma error checking and recovery
sparc: bpf_jit: fix support for ldx/stx mem and SKF_AD_VLAN_TAG
can: at91_can: add missing prepare and unprepare of the clock
...
Some ATA drivers need the dma drain size workaround, and thus need to
call blk_mq_start_request before the S/G mapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow blk-mq to pass an argument to the timeout handler to indicate
if we're timing out a reserved or regular command. For many drivers
those need to be handled different.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we've changed the driver API on the submission side use the
opportunity to fix up the name on the completion side to fit into the
general scheme.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we call blk_mq_start_request from the core blk-mq code before calling into
->queue_rq there is a racy window where the timeout handler can hit before we've
fully set up the driver specific part of the command.
Move the call to blk_mq_start_request into the driver so the driver can start
the request only once it is fully set up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pass an explicit parameter for the last request in a batch to ->queue_rq
instead of using a request flag. Besides being a cleaner and non-stateful
interface this is also required for the next patch, which fixes the blk-mq
I/O submission code to not start a time too early.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
LIBFC depends upon SCSI_FC_ATTRS and select's CRC32C.
The only alternative would be to 'select' CRC32C and all of
SCSI_FC_ATTRS direct and indirect dependencies in the Kconfig section
for every LIBFCOE user which makes little sense.
Subsequently, use 'depends' instead of 'select' for LIBFCOE too.
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgbi_inet6addr_handler() can be called in interrupt context, so use rcu
protected list while finding netdev
Applies on top of core-for-3.18
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Fixes: fc8d0590d9 ("libcxgbi: Add ipv6 api to driver")
Fixes: 759a0cc5a3 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6
api")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Get rid of the warning messages since they will clutter up various system logs
and are of questionable value to the end user. For debugging purposes, this
information can be gotten by setting the scsi log level appropriately.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch will fix the below compilation errors on i386 ARCH
drivers/built-in.o: In function `_scsih_qcmd':
mpt2sas_scsih.c:(.text+0x1e7b56): undefined reference to `__udivdi3'
mpt2sas_scsih.c:(.text+0x1e7b8a): undefined reference to `__umoddi3'
Used sector_div() API to fix above compilation errors.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When ending a bi-directionional SCSI request, blk_finish_request()
cleans up and frees the request, but scsi_release_bidi_buffers() tries
to indirect through the request to find it's data buffers. This causes
a panic due to a null pointer dereference.
Move the call to scsi_release_bidi_buffers() before the call to
blk_finish_request().
Signed-off-by: Daniel Gryniewicz <dang@linuxbox.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu.
This function is used by iscsi drivers and userspace to send iscsi PDUs/
commands. For login commands, we have a set buffer size. For all other
commands we do not support data buffers.
This was reported by Dan Carpenter here:
http://www.spinics.net/lists/linux-scsi/msg66838.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There are other kconfig symbols which use SCSI_FC_ATTRS.
In order to maintain sanity and prevent kconfig warnings, change
all of these from using 'select' to using 'depends on' so that
proper symbol dependencies will be honored and circular depends
problems will be avoided.
This fixes kconfig warnings and build errors:
warning: (LIBFC && SCSI_IBMVFC && SCSI_QLA_FC && SCSI_LPFC && ZFCP && SCSI_BFA_FC && SCSI_CHELSIO_FCOE && FUSION_FC) selects SCSI_FC_ATTRS which has unmet direct dependencies (SCSI && NET)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_event':
drivers/scsi/scsi_transport_fc.c:543:7: error: 'scsi_nl_sock' undeclared (first use in this function)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_vendor_event':
drivers/scsi/scsi_transport_fc.c:611:7: error: 'scsi_nl_sock' undeclared (first use in this function)
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call scsi_scan_host at the end of host initialization and fix and error path
to free allocated resource.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add code to support the new Areca Raid ARC12x4 series adapters.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Revise comment and some character strings.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Rewrite ioctl entry and its relate function. This patch fix ioctl data
read/write error and change data I/O access from byte to Dword.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This modification is for consistency with upcoming adapter type D.
Both adapter type B and D have similar H/W and S/W structure.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Rename some variable and function names for readability and consistency.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Clear outbound doorbell buffer completely for adapter type C. This is to
prevent getting bad data input from IOP before ioctl command processing
starts.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Adjust printing order of adapter model name and firmware version.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove calling arcmsr_hbb_enable_driver_mode by in-lining the code into
the caller.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Revise message_isr_bh_fn to remove the duplicate code for each adapter type.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes the wrong return status of abort command.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch limits the max. number of SCSI commmand request to avoid command
overflow.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds code to support system hibernation.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds code to support MSI and MSI-X interrupt.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch rewrites the interrupt service routine relate function to fix
a command timeout under heavy controller load.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments by Tomas Henzl.
Driver version upgrade patch.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Added comment for to-do work.
Problem statement:
MFI link list in megaraid_sas driver is used from mfi-mpt pass-through commands.
This list can be corrupted due to many possible race conditions in driver and
eventually we may see kernel panic.
One example -
MFI frame is freed from calling process as driver send command via polling method and interrupt
for that command comes after driver free mfi frame (actually even after some other context reuse
the mfi frame). When driver receive MPT frame in ISR, driver will be using the index of MFI and
access that MFI frame and finally in-used MFI frame’s list will be corrupted.
High level description of new solution -
Free MFI and MPT command from same context.
Free both the command either from process (from where mfi-mpt pass-through was called) or from
ISR context. Do not split freeing of MFI and MPT, because it creates the race condition which
will do MFI/MPT list corruption.
Renamed the cmd_pool_lock which is used in instance as well as fusion with below name.
mfi_pool_lock and mpt_pool_lock to add more code readability.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Current driver does fast path read load balancing between arm and mirror disk
for two Drive Raid-1 configuration only.
Now, Driver support fast path read load balancing for all (any number of disk) Raid-1 configuration.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
For certain deployment, we may need to disable irq cpu affinity hint.
This module parameter provides option for use to disable irq cpu affinity hint
and allow irqbalancer to handle the rest.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Round down the max sge to power of two.
Earlier max sge limit is 70 SGE, which will allow block layer to send 280K IO frame.
It is optimal to provide max IO size aligned to the smallest possible stripe size.
E.a
Consider that we have configured RAID Volumes which does not allow Fast Path across the stripe.
Raid volume with stripe size = 256K, will have peformance hit if we get io frame of size 280K.
Driver will not send IO frame large than stripe size to the Fast Path.
Also, FW will convert 280K frame into 256K + 24K. This is an additional overhead.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Megaraid_sas driver can now work in host lock less mode.
Remove host lock less as megaraid_sas driver will have safer access to raid map as described in earlier patch.
We now keep Driver Raid map copy, which will make sure
that driver will always have old or new map
Driver raid map will be replaced safely in MR_PopulateDrvRaidMap(), so there is no issue
even if IO is continue from the scsi mid layer.
There is a plan to remove "host_lock" and "hba_lock" usage from megaraid_sas in future.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
reserved1 field(part of union) of Raid map struct was not required so it is removed.
Current MegaRAID firmware and hence the driver only supported 64VDs.
E.g: If the user wants to create more than 64VD on a controller,
it is not possible on current firmware/driver.
New feature and requirement to support upto 256VD, firmware/driver/apps need changes.
In addition to that there must be a backward compatibility of the new driver with the
older firmware and vice versa.
RAID map is the interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives.
In the earlier design driver was using the FW copy of RAID map where as
in the new design the Driver will keep the RAID map copy of its own; on which
it will operate for any raid map access in fast path.
Local driver raid map copy will provide ease of access through out the code
and provide generic interface for future FW raid map changes.
For the backward compatibility driver will notify FW that it supports 256VD
to the FW in driver capability field.
Based on the controller properly returned by the FW, the Driver will know
whether it supports 256VD or not and will copy the RAID map accordingly.
At any given time, driver will always have old or new Raid map.
So with this changes, driver can also work in host lock less mode. Please
see next patch which enable host lock less mode for megaraid_sas driver.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Move buff_offset inside spinlock, corrected loop at crash dump buffer free,
reset_devices check is added to disable fw crash dump feature in kdump kernel.
This feature will provide similar interface as kernel crash dump feature.
When megaraid firmware encounter any crash, driver will collect the firmware raw image and
dump it into pre-configured location.
Driver will allocate two different segment of memory.
#1 Non-DMA able large buffer (will be allocated on demand) to capture actual FW crash dump.
#2 DMA buffer (persistence allocation) just to do a arbitrator job.
Firmware will keep writing Crash dump data in chucks of DMA buffer size into #2,
which will be copy back by driver to the host memory as described in #1.
Driver-Firmware interface:
==================
A.) Host driver can allocate maximum 512MB Host memory to store crash dump data.
This memory will be internal to the host and will not be exposed to the Firmware.
Driver may not be able to allocate 512 MB. In that case, driver will do possible memory
(available at run time) allocation to store crash dump data.
Let’s call this buffer as Host Crash Buffer.
Host Crash buffer will not be contigious as a whole, but it will have multiple chunk of contigious memory.
This will be internal to driver and firmware/application are unaware of it.
Partial allocation of Host Crash buffer may have valid information to debug depending upon
what was collected in that buffer and depending on nature of failure.
Complete Crash dump is the best case, but we do want to capture partial buffer just to grab something rather than nothing.
Host Crash buffer will be allocated only when FW Crash dump data is available,
and will be deallocated once application copy Host Crash buffer to the file.
Host Crash buffer size can be anything between 1MB to 512MB. (It will be multiple of 1MBs)
B.) Irrespective of underlying Firmware capability of crash dump support,
driver will allocate DMA buffer at start of the day for each MR controllers.
Let’s call this buffer as “DMA Crash Buffer”.
For this feature, size of DMA crash buffer will be 1MB.
(We will not gain much even if DMA buffer size is increased.)
C.) Driver will now read Controller Info sending existing dcmd “MR_DCMD_CTRL_GET_INFO”.
Driver should extract the information from ctrl info provided by firmware and
figure out if firmware support crash dump feature or not.
Driver will enable crash dump feature only if
“Firmware support Crash dump” +
“Driver was able to create DMA Crash Buffer”.
If either one from above is not set, Crash dump feature should be disable in driver.
Firmware will enable crash dump feature only if “Driver Send DCMD- MR_DCMD_SET_CRASH_BUF_PARA with MR_CRASH_BUF_TURN_ON”
Helper application/script should use sysfs parameter fw_crash_xxx to actually copy data from
host memory to the filesystem.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Current driver updates reply post host index to let firmware know that replies are processed,
while returning from ISR function, only if there is no oustanding replies in reply queue.
Driver will free the request frame immediately from ISR but reply post host index is not yet updated.
It means freed request can be used by submission path and there may be a tight loop in request/reply
path. In such condition, firmware may crash when it tries to post reply and there is no free
reply post descriptor.
Eventually two things needs to be change to avoid this issue.
Increase reply queue depth (double than request queue) to accommodate worst case scenario.
Update reply post host index to firmware once it reach to some pre-defined threshold value.
This change will make sure that firmware will always have some buffer of reply descriptor and
will never find empty reply descriptor in completion path.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Reduce the assingment for u64 req_data variable.
Use writeq() for 64bit PCI write instead of writel() to avoid additional lock overhead.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Current driver allow device scan for all the devices on channel 0 and 1.
E.a If we have two single drive raid volumes, we may see prints like below.
First two prints are for physical device which are used to form VD.
Prints like this creates confusion as it is really not required to scan any
hidden physical devices.
scsi1 : LSI SAS based MegaRAID driver
scsi 1:0:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:0:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:2:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:2:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
When slave_alloc called, sdev-type will not be set, so current code will always
return "0" in slave_alloc callback.
This patch make sure that driver return "-ENXIO" for non-syspd devices.
After this patch, we will see prints in syslog only for devices which are exposed.
For current example, below print will be available in syslog.
scsi1 : LSI SAS based MegaRAID driver
scsi 1:2:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:2:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In _scsih_probe, propagate the return value from scsi_add_host.
In mpt3sas, avoid calling list_del twice if that returns an
error, which causes list_del corruption warnings if an error
is returned.
Tested with blk-mq and scsi-mq patches to properly cleanup
from and propagate blk_mq_init_rq_map errors.
Signed-off-by: Robert Elliott <elliott@hp.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt3sas driver version to 04.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Up to now, Driver allocates a single contiguous block of memory
pool for all reply queues and passes down a single address in the
ReplyDescriptorPostQueueAddress field of the IOC Init Request
Message to the firmware.
When firmware receives this address, it will program each of the
Reply Descriptor Post Queue registers, as each reply queue has its
own register. Thus the firmware, starting from a base address it
determines the starting address of the subsequent reply queues
through some simple arithmetic calculations.
The size of this contiguous block of memory pool is directly proportional
to number of MSI-X vectors and the HBA queue depth. For example higher
MSIX vectors requires larger contiguous block of memory pool.
But some of the OS kernels are unable to allocate this larger
contiguous block of memory pool.
So, the proposal is to allocate memory independently for each
Reply Queue and pass down all of the addresses to the firmware.
Then the firmware will just take each address and program the value
into the correct register.
When HBAs with older firmware(i.e. without RDPQ capability) is used
with this new driver then the max_msix_vectors value would be set
to 8 by default.
Change set in v1:
1. Declared the _base_get_ioc_facts() functions at the beginning of the mpt3sas_base.c file
instead of moving all these functions before mpt3sas_base_map_resources() function
a. _base_wait_for_doorbell_int()
b. _base_wait_for_doorbell_ack()
c. _base_wait_for_doorbell_not_used()
d. _base_handshake_req_reply_wait()
e. _base_get_ioc_facts()
2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask
after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask.
This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same.
3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions
a. _base_release_memory_pools()
b. _base_allocate_memory_pools()
c. _base_send_ioc_init()
d. _base_make_ioc_operational()
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Copyright in driver sources is updated for year the 2014.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Below is the change set in MPI2.5 Rev H specification and 2.00.32 header files
1) Added reserved fields to IO Unit Page 7 for future use.
2) Added optional functionality to IOCInit Request so that
the host may specify a separate base address for each
Reply Descriptor Post Queue. IOC support for this is
indicated using a new IOCCapabilities bit in the IOCFacts Reply.
3) Added Toolbox Console Text Display Tool
The host uses the Console Text Display Tool to send a string to
IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal).
4) Firmware images can now be signed using an encrypted hash.
5) Added MPI2_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL
6) Added more details about configuration page restrictions when Host Based Discovery is enabled
Enabling host based discovery affects the availability of some configuration pages and events.
The SAS Expander, SAS Device, and SAS Enclosure configuration pages are not available from the IOC.
The IOC returns an error status to any Configuration Request message attempting to access these pages.
The IOC does not send the SAS Discovery Event, the SAS Topology Change List Event, or
the SAS Enclosure Device Status Change Event when host based discovery is enabled.
7) Bit 13 of the SAS IO Unit Page 1 ControlFlags field is now obsolete.
It was used to enable limiting direct attached SATA maximum link rate to 1.5 Gbps.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt3sas driver version to 03.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Added code to send an SEP message that turns off the Predictive
Failure LED when a drive is removed (if Predictive Failure LED was turned on).
Added a new flag 'pfa_led_on' per device that tracks the status of Predictive
Failure LED. When the drive is removed, this flag is checked and
sends an SEP message to turn off the respective Predictive Failure LED.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Below is the change set in MPI2.5 Rev G specification and 2.00.31 header files
1) Added SCSIStatusQualifier to SCSI IO Error Reply message.
2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field.
3) Added Allow Protection Information bit for IR Volume Create.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt2sas driver version to 18.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state.
This patch will make sure that
1.Driver to send IOC facts request message only if HBA is in operational or ready state.
2.If IOC is in fault state, a diagnostic reset would be issued.
3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state.
If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Up to now, Driver allocates a single contiguous block of memory
pool for all reply queues and passes down a single address in the
ReplyDescriptorPostQueueAddress field of the IOC Init Request
Message to the firmware.
When firmware receives this address, it will program each of the
Reply Descriptor Post Queue registers, as each reply queue has its
own register. Thus the firmware, starting from a base address it
determines the starting address of the subsequent reply queues
through some simple arithmetic calculations.
The size of this contiguous block of memory pool is directly proportional
to number of MSI-X vectors and the HBA queue depth. For example higher
MSIX vectors requires larger contiguous block of memory pool.
But some of the OS kernels are unable to allocate this larger
contiguous block of memory pool.
So, the proposal is to allocate memory independently for each
Reply Queue and pass down all of the addresses to the firmware.
Then the firmware will just take each address and program the value
into the correct register.
When HBAs with older firmware(i.e. without RDPQ capability) is used
with this new driver then the max_msix_vectors value would be set
to 8 by default.
Change_set in v1:
1. Declared _base_get_ioc_facts() function at the beginning of the mpt2sas_base.c
file instead of moving all these functions before mpt2sas_base_map_resources() function
a. _base_wait_for_doorbell_int()
b. _base_wait_for_doorbell_ack()
c. _base_wait_for_doorbell_not_used()
d. _base_handshake_req_reply_wait()
e. _base_get_ioc_facts()
2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask
after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask.
This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same.
3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions
a. _base_release_memory_pools()
b. _base_allocate_memory_pools()
c. _base_send_ioc_init()
d. _base_make_ioc_operational()
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A type casting error caused the max volume LBA to be truncated from 64
to 32 bits. The virtual LBA would also get truncated to 32 bits in the
case of a 16-byte READ/WRITE command.
Rewrite entire function to get rid of code duplication and type casts.
Use get/put_unaligned wrappers to extract and replace the LBA field in
the MPI request CDB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt2sas driver version to 17.100.00.00
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Added code to send a SEP message that turns off the Predictive
Failure LED when a drive is removed (if Predictive Failure LED was turned on).
Added a new flag 'pfa_led_on' per device that tracks the status of Predictive
Failure LED. When the drive is removed, this flag is checked and
sends the SEP message to turn off the respective Predictive Failure LED.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
