* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire-up new system calls
microblaze: Remove NO_IRQ from architecture
input: xilinx_ps2: Don't use NO_IRQ
block: xsysace: Don't use NO_IRQ
microblaze: Trivial asm fix
microblaze: Fix debug message in module
microblaze: Remove eprintk macro
microblaze: Send CR before LF for early console
microblaze: Change NO_IRQ to 0
microblaze: Use irq_of_parse_and_map for timer
microblaze: intc: Change variable name
microblaze: Use of_find_compatible_node for timer and intc
microblaze: Add __cmpdi2
microblaze: Synchronize __pa __va macros
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
This is where the really nasty conflicts in the samsung platform
start, due to some files getting moved around and combined in the
'restart' branch that has already gone into mainline through
Russell's tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XY2N
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
Conflicts:
arch/arm/mach-exynos/Makefile
arch/arm/mach-exynos/cpu.c -> common.c
arch/arm/mach-exynos/include/mach/entry-macro.S
arch/arm/mach-exynos/init.c -> common.c
arch/arm/mach-s5p64x0/init.c -> common.c
arch/arm/mach-s5pv210/init.c -> common.c
Multiple files were moved into common.c files in the rmk/for-linus
branch, so this moves over the samsung/dt changes to the new
files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers shouldn't use NO_IRQ. Microblaze and PPC
define NO_IRQ as 0 and this reference will be removed
in near future.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
CC: Rob Herring <rob.herring@calxeda.com>
Instead of manually create and handler kernel thread switch to threaded
IRQ and let kernel IRQ core manage thread for us.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Let compiler figure out which ones makes most sense to inline.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add __devinit/__devexit sections annotations so parts of code could be
discarded after completing driver initialization.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
So that it has proper symlink to the containing module in sysfs.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of using legacy PM interfaces switch to using dev_pm_ops.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The 'name', 'owner', and 'mod_name' members are redundant with the
identically named fields in the 'driver' sub-structure. Rather than
switching each instance to specify these fields explicitly, introduce
a macro to simplify this.
Eliminate further redundancy by allowing the drvname argument to
DEFINE_XENBUS_DRIVER() to be blank (in which case the first entry from
the ID table will be used for .driver.name).
Also eliminate the questionable xenbus_register_{back,front}end()
wrappers - their sole remaining purpose was the checking of the
'owner' field, proper setting of which shouldn't be an issue anymore
when the macro gets used.
v2: Restore DRV_NAME for the driver name in xen-pciback.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Several protocol initialization routines can fail after they set up
psmouse methods, such as reconnect and disconnect. This may lead to
these stale methods used with different protocol that they were
intended to be used for and may cause unpredictavle behavior and/or
crashes.
Make sure we start with a clean slate before executing each and every
protocol detection and/or initialization routine.
Reported-by: Paul Fox <pgf@laptop.org>
Acked-by: Tai-hwa Liang <avatar@sentelic.com>
Acked-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If there is a full packet in the buffer, and we overflow that buffer
right after checking for that condition, it would have been possible
for us to block indefinitely (rather, until the next full packet) even if
the file was marked as O_NONBLOCK.
Cc: Jeff Brown <jeffbrown@android.com>
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this, it was possible for the reader to get ahead of packet_head.
If the input device generated a partial packet *right* after the reader
got ahead, then we can get into a situation where the device is marked
readable, but read always returns 0 until the next packet is finished
(i.e a SYN is generated by the input driver).
This situation can also happen if we overflow the buffer while a reader
is trying to read an event out.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When runtime power management is enabled put the Samsung keypad driver
into suspend mode with wakeups disabled whenever the device is open but
a key is not actually been pressed. As well as saving a trivial amount of
power this will support the use of SoC wide idle modes which put the entire
device into a retention mode and use explicit wakeup sources to exit.
Since not all of the interrupt controllers used with the driver support
set_irq_wake() (though they all do the right thing) and there's a nasty
WARN() when we disable wake after failing to enable it keep track of the
current wake status from runtime PM and only disable wake if we managed
to enable it; I'm not entirely sure why this doesn't affect the existing
uses of the API in the driver.
System suspend is unaffected as the driver core will runtime resume any
suspended devices prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
drivers/input/keyboard/samsung-keypad.c
This adds a simple device tree binding to the tegra keyboard controller.
Also, mark the default keymap as __devinitdata since it is not referenced
after boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fixing wrong register offset which is used to retrieve the number of buttons
attached to the hardware.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since commit 6384fd "ARM: pxa: rename IRQ_GPIO to PXA_GPIO_TO_IRQ",
I got below buid errors due to implicit declaration of function 'IRQ_GPIO'.
Use common gpio_to_irq() to replace machine dependant macro IRQ_GPIO().
CC drivers/input/touchscreen/zylonite-wm97xx.o
drivers/input/touchscreen/zylonite-wm97xx.c: In function 'zylonite_wm97xx_probe':
drivers/input/touchscreen/zylonite-wm97xx.c:195: error: implicit declaration of function 'IRQ_GPIO'
make[3]: *** [drivers/input/touchscreen/zylonite-wm97xx.o] Error 1
make[2]: *** [drivers/input/touchscreen] Error 2
make[1]: *** [drivers/input] Error 2
make: *** [drivers] Error 2
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some displays from AUO have a so called in-cell touchscreen, meaning it
is built directly into the display unit.
Touchdata is gathered through PIXCIR Tango-ICs and processed in an
Atmel ATmega168P with custom firmware. Communication between the host
system and ATmega is done via I2C.
Devices using this touch solution include the Dell Streak5 and the family
of Qisda ebook readers.
The driver reports single- and multi-touch events including touch area
values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* pm-domains:
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
PM / Domains: Provide an always on power domain governor
PM / Domains: Fix default system suspend/resume operations
PM / Domains: Make it possible to assign names to generic PM domains
PM / Domains: fix compilation failure for CONFIG_PM_GENERIC_DOMAINS unset
PM / Domains: Automatically update overoptimistic latency information
PM / Domains: Add default power off governor function (v4)
PM / Domains: Add device stop governor function (v4)
PM / Domains: Rework system suspend callback routines (v2)
PM / Domains: Introduce "save/restore state" device callbacks
PM / Domains: Make it possible to use per-device domain callbacks
Make the st1232 driver use dev_pm_qos_add_ancestor_request() to
add a device PM QoS latency constraint for the controller it
depends on, so that the controller won't go into an overly deep
low-power state when the touchscreen has to be particularly
responsive (e.g. when the user moves his or her finger on it).
This change is based on a prototype patch from Guennadi Liakhovetski.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This will improve the output of the sensor.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This also changes the devname parameter delivered to
request_threaded_irq() from "mpu_int" to "mpu3050".
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make sure that mutex is released upon register writing failure.
This fixes boot freezing observed on ARM based OLPC
(http://dev.laptop.org/ticket/11357).
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add device tree based discovery support for Samsung's keypad controller.
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - fix touchpad not working after S2R on Vostro V13
Input: cma3000_d0x - fix signedness bug in cma3000_thread_irq()
Input: wacom - add product id used by Samsung Slate 7
The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics touchpads on several Dell laptops, particularly Vostro V13
systems, may not respond properly to PS/2 commands and queries immediately
after resuming from suspend to RAM. This leads to unresponsive touchpad
after suspend/resume cycle.
Adding a 1-second delay after resetting the device allows touchpad to
finish initializing (calibrating?) and start reacting properly.
Reported-by: Daniel Manrique <daniel.manrique@canonical.com>
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for Sharp's GP2AP002A00F proximity sensor. The
proximity is measured as a binary switch, i.e. an object is either
detected or not detected. Hence, this driver is implemented as a switch
that reports SW_FRONT_PROXIMITY.
Reviewed-by: Datta Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: Courtney Cavin <courtney.cavin@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts mc13783-pwrbutton to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.
Also staticise mc13783_pwrbutton_driver which is not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Register input device last so that we do not have to reset
input device pointer after calling input_unregister_device().
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The error check (intr_status < 0) didn't work because intr_status is
a u8. Change its type to signed int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New product ID reported by Harvey Braun on linuxwacom mailing list
and also tested this patch with new hardware.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Having module device table based on PNP id produces the following warning:
CC drivers/input/touchscreen/htcpen.o
drivers/input/touchscreen/htcpen.c:50: warning: 'pnp_ids' defined but not used
This happens because it is not a PNP driver, bit rather ISA driver and
pnp_ids table is not used anywhere. To fix this issue let's switch to
DMI-based module table instead,
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This variant was introduced in
i2c: boilerplate function for byte swapped smbus_write/read_word_data
This also has the side effect of ensuring any errors from the i2c
read and no longer mangled.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There exist tilt switches that simply report their tilt-state via
some gpios. The number and orientation of their axes can vary
depending on the switch used and the build of the device. Also two
or more one-axis switches could be combined to provide multi-dimensional
orientation.
One example of a device using such a switch is the family of Qisda
ebook readers, where the switch provides information about the
landscape / portrait orientation of the device. The example in
Documentation/input/gpio-tilt.txt documents exactly this one-axis
device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It turns out that v4's firmware provides a command so we can query
the resolution. Let's use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Starting with v3 hardware, the firmware supports this shorter
elantech_send_cmd. Teach the driver to use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This converts the drivers in drivers/input/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Henk Vergonet <Henk.Vergonet@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: "Magnus Hörlin" <magnus@alefors.se>
Cc: Chris Moeller <kode54@gmail.c>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Edwin van Vliet <edwin@cheatah.nl>
Cc: Ping Cheng <pingc@wacom.com>
Cc: Eduard Hasenleithner <eduard@hasenleithner.at>
Cc: Alexander Strakh <strakh@ispras.ru>
Cc: Glenn Sommer <gsommer@datanordisk.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PM methods are basically the same for SPI and I2C busses, so let's
use the same dev_pm_ops for both of them.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the EETI eGalax serial multi touch controller driver.
EETI eGalax serial touch screen controller is a I2C based multiple
capacitive touch screen controller, it can support 5 touch events maximum.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We have determined that the jumpiness previously seen when using
the synaptics kernel mouse driver on OLPC XO was due to not using
the synaptics X11 userspace driver - the xf86-input-evdev driver was
interpreting 'finger near pad' signals as movements. Newer versions
of xf86-input-evdev fix this issue.
Additionally, the synaptics kernel driver is now usable on this
platform, but only when run in relative mode.
Update the comment and refine the check to allow the synaptics driver
to run on OLPC XO in relative mode.
We will continue investigating the EC issue as time becomes available.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is nothing in keypad platform definitions that requires
the driver be complied on Samsung platform only, so let's move them
out of the platform subdirectory and relax the dependencies.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, the synaptics driver puts the device into Absolute mode.
As explained in the synaptics documentation section 3.2, in this mode,
the device sends a continuous stream of packets at the maximum rate
to the host when the user's fingers are near or on the pad or
pressing buttons, and continues streaming for 1 second afterwards.
These packets are even sent when there is no new information to report,
even when they are duplicates of the previous packet.
For embedded systems this is a bit much - it results in a huge
and uninterrupted stream of interrupts at high rate.
This patch adds support for Relative mode, which can be selected as
a new psmouse protocol. In this mode, the device does not send duplicate
packets and acts like a standard PS/2 mouse. However, synaptics-specific
functionality is still available, such as the ability to set the packet
rate, and rather than disabling gestures and taps at the hardware level
unconditionally, a 'synaptics_disable_gesture' sysfs attribute has
been added to allow control of this functionality.
This solves a long standing OLPC issue: synaptics hardware enables
tap to click by default (even in the default relative mode), but we
have found this to be inappropriate for young children and first
time computer users. Enabling the synaptics driver disables tap-to-click,
but we have previously been unable to use this because it also enables
Absolute mode, which is too "spammy" for our desires and actually
overloads our EC with its continuous stream of packets. Now we can enable
the synaptics driver, disabling tap to click while retaining the less
noisy Relative mode.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix the following compilation failure with v3.2-rc1 by including module.h:
CC drivers/input/serio/ams_delta_serio.o
drivers/input/serio/ams_delta_serio.c:33:15: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:34:20: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:35:16: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c: In function 'ams_delta_serio_init':
drivers/input/serio/ams_delta_serio.c:155:2: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/input/serio/ams_delta_serio.c:155:2: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes some v3 hardware (fw_version: 0x150500) wrongly detected
as v2 hardware.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Tested-By: Marc Dietrich <marvin24@gmx.de>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for two ALPS touchpad protocols not
supported currently by the driver, which I am arbitrarily naming
version 3 and version 4. Support is single-touch only at this time,
although both protocols are capable of limited multitouch support.
Thanks to Andrew Skalski, who did the initial reverse-engineering
of the v3 protocol.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for version 4 protocol support, which has 8-byte
data packets, remove all hard-coded assumptions about packet size
and use psmouse->pktsize instead.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for adding support for more ALPS protocol versions,
add a field for the protocol version to the model info instead of
using a field in the flags. OLDPROTO and !OLDPROTO are now called
version 1 and version 2, repsectively.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for new protocol support, move the protocol
information currently documented in alps.c to
Documentation/input/alps.txt, where it can be expanded without
cluttering up the driver.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's Pen and Touch packets always start with a value
of 0x02 in first byte. In 3rd gen Bamboo's, the hw is now
periodically sending some additional packets with unrelated data
and uses a value other than 0x02 to inform driver this.
Ignore those packets now.
This was reported by users as bad behavior in Gimp. The
invalid packets being processed made the stylus report
out of proximity for the 1 packet and this triggered some
secondary bug which caused Gimp to stop drawing until
user really took pen out of proximity of tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Touchpad input doesn't work with newer HP Pavilion dv4 laptops due to bad i8042
timeout data. Booting with i8042.notimeout and i8042.nomux successfully works
around the problem.
This patch adds the devices to the i8042 notimeout and nomux blacklists.
Signed-off-by: Tomas Miljenovic <TomasM@tomasm.tk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In addition to some laptops needing i8042 reset after resuming from S2R to
get their touchpads working there is another class of laptops - ones that
need i8042 reset before going to S2R, otherwise they will simply reboot
instead of resuming.
See https://bugzilla.kernel.org/show_bug.cgi?id=15612
This change forces reset of i8042 before doing S2R.
Reported-by: Stefan Koch <stefan_koch@gmx.net>
Tested-by: Alexander van Loon <a.vanloon@alexandervanloon.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
These files are not modules but are exporting symbols and/or
making use of THIS_MODULE macro.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in input dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (348 commits)
[media] pctv452e: Remove bogus code
[media] adv7175: Make use of media bus pixel codes
[media] media: vb2: fix incorrect return value
[media] em28xx: implement VIDIOC_ENUM_FRAMESIZES
[media] cx23885: Stop the risc video fifo before reconfiguring it
[media] cx23885: Avoid incorrect error handling and reporting
[media] cx23885: Avoid stopping the risc engine during buffer timeout
[media] cx23885: Removed a spurious function cx23885_set_scale()
[media] cx23885: v4l2 api compliance, set the audioset field correctly
[media] cx23885: hook the audio selection functions into the main driver
[media] cx23885: add generic functions for dealing with audio input selection
[media] cx23885: fixes related to maximum number of inputs and range checking
[media] cx23885: Initial support for the MPX-885 mini-card
[media] cx25840: Ensure AUDIO6 and AUDIO7 trigger line-in baseband use
[media] cx23885: Enable audio line in support from the back panel
[media] cx23885: Allow the audio mux config to be specified on a per input basis
[media] cx25840: Enable support for non-tuner LR1/LR2 audio inputs
[media] cx23885: Name an internal i2c part and declare a bitfield by name
[media] cx23885: Ensure VBI buffers timeout quickly - bugfix for vbi hangs during streaming
[media] cx23885: remove channel dump diagnostics when a vbi buffer times out
...
Fix up trivial conflicts in drivers/misc/altera-stapl/altera.c (header
file rename vs add)
This driver has been tested with hardware and works as expected. To use
it add the platform data as appropriate and register it with the
corresponding I2C bus.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
