Enable the isochrounous IN handling for AM335x HOST.
Reprogram CPPI to receive consecutive ISOCH frames in the same URB.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=N4//
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).
Pass compile test with below commands:
make O=outout/all allmodconfig
make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dsps platform needs to save save some registers at suspend time and
restore them after resume. This patch adds a struct for these registers,
and also lets the musb core know that the core registers need to be
saved as well.
We also have to explicitly de-assert the port reset upon resume on this
platform, but musb_port_reset() should not be called from glue layers.
Hence, introduce a flag in struct musb_hdrc_config for this.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make musb_port_suspend() externally available, and call it when to host
goes into suspend. This allows the core to go into suspend while a
device is connected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_shutdown() removes always USB host and device.
musb_init_controller() adds host and device depending on port_mode. If
port mode is set to HOST then the removal of UDC leads only to:
|(NULL device *): gadget not registered.
and nothing else happens. If port mode is set to DEVICE and we remove
the host then we oops in usb_remove_hcd().
This patch ensures that we only remove host in OTG/host mode and device
only in OTG/device mode to avoid any trouble.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=O9AH
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.11 merge window
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch attempts to fix the isochonour API in the musb host
driver. In particular, the urb->start_frame field should always be
set by the driver; it isn't an input parameter.
The simplest way to accomplish this is to treat all URBs as though the
URB_ISO_ASAP flag was set. This won't give the right behavior when an
underrun occurs, but I don't know enough about the musb driver to
handle that case.
Unfortunately, I have no way to test this change.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
very minor patch fixing the following build warning on
a debug message:
drivers/usb/musb/musb_host.c: In function ‘musb_host_rx’:
drivers/usb/musb/musb_host.c:1763:4: warning: format ‘%x’ \
expects argument of type ‘unsigned int’, but argument \
6 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since highmem PIO URB handling was introduced in:
8e8a551 usb: musb: host: Handle highmem in PIO mode
when a URB is being handled it may happen that the static use_sg flag
was set by a previous URB with buffer in highmem. This leads to error
in handling the present URB.
Fix this by making the use_sg flag URB specific.
Cc: stable <stable@vger.kernel.org> # 3.7+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Host side dma support for ux500 is enabled by piggybacking on Inventra
dma support.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With the hcd is now a direct member of struct musb, we can now simply
eliminate the musb_to_hcd() macro. There aren't that many users left
anyway, as some where already fixed up when parts were factored out to
musb_host.c
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch re-introduces the bits that are necessary to use the musb
controller in host mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb struct is currently allocated along with the hcd, which makes
it difficult to build a driver that only acts as gadget device.
Fix this by allocating musb directly, and keep the hcd around as
a pointer in the musb struct.
struct hc_driver musb_hc_driver can now also be static to musb_host.c,
and the macro musb_to_hcd() is just a pointer dereferencer for now, and
will be eliminated later.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In particular, this introduces musb_host_resume_root_hub()and
musb_host_poke_root_hub() which will be stubbed out later.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
MUSB controller cannot work in DMA mode with misaligned buffers,
switching in PIO mode.
HCD core has hooks that allow to override the default DMA
mapping and unmapping routines for host controllers that have
special DMA requirements, such as alignment constraints.
It is observed that work in PIO mode is slow and it's better
to align buffers properly before passing them to MUSB
This increased throughput 80->120 MBits/s over musb@omap4 with
USB Gigabit Ethernet adapter attached.
Some ideas are taken from ehci-tegra.c
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
all other functions under drivers/usb/ start
with usb_, let's do the same thing.
This patch is in preparation for moving otg_state_string
to usb-common.c and deleting otg.c completely.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever an URB is programmed for transfer, the TXFIFO
is flushed. This results in valid packets of the
previous transfer to get flushed when double buffering
is enabled (The MUSB_TXCSR_FIFONOTEMPTY bit in TXCSR
is set indicating that a packet in the FIFO is yet to be sent)
For ex:- In Host mode Audio, noise is heard in the headset
when double buffering is enabled on the ISO endpoint.
The fifo flush is removed for double buffering case.
The fifo is now flushed only in cases of error or when
aborting a transfer.
Also, In Host MSC case, data toggle errors are seen when double
buffering is enabled on the bulk endpoint. Whenever an URB is
programmed for transfer, the data toggle is set manually
resulting in data toggle errors on the bus. Leave the data
toggle handling upto the hardware in the double buffering case.
Signed-off-by: supriya karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "mult" factor is not updated properly for the can_bulk_split()
case.
The AUTOSET bit in the TXCSR is not being set if the "mult"
factor is greater than 1 for the High Bandwidth ISO case.
But the "mult" factor is also greater than 1 in case of Full speed
bulk transfers with the packet splitting in TXMAXP register
enabled with can_bulk_split().
Without the AUTOSET the DMA transfers will not progress in mode1
[ balbi@ti.com : fix braces placement ]
Signed-off-by: supriya karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRTXE results in an 32bit read
access which also reads INTRRX and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRTXE so we only perform
write access to it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when using musb_urb_enqueue to submit three urbs to the same endpoint, when
hep->hcpriv is NULL, qh will be allocated when the first urb is completed.
When the IRQ completes the next two urbs, qh->hep->hcpriv will be set to NULL.
Now the second urb get musb->lock and executes musb_schedule(), but
next_urb(qh) is NULL, so musb_start_urb will Oops.
[ balbi@ti.com : practically rewrote commit log so it makes sense ]
Signed-off-by: mayuzheng <myz147@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of USB bulk transfer, when himem page
is received, the usb_sg_init function sets the
urb transfer buffer to NULL. When such URB
transfer is handled, kernel crashes in PIO mode.
Handle this by mapping the highmem buffer in PIO mode.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk TX endpoint.
This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled.
This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is to reduce the overhead of dma programming for zero byte
transmit as same can be done using pio mode.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just two patches here:
First we have a fix to disable DMA in case DMA channel
request fails.
Second, there's a fix for situations where the user
kills musb (by rmmod or any other means) while a
transfer is on the fly. In such cases, we could be
led into a NULL pointer dereference due to endpoint
being disabled and endpoint descriptor being NULL.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=4uPD
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: musb: patches for v3.6 merge window
Just two patches here:
First we have a fix to disable DMA in case DMA channel
request fails.
Second, there's a fix for situations where the user
kills musb (by rmmod or any other means) while a
transfer is on the fly. In such cases, we could be
led into a NULL pointer dereference due to endpoint
being disabled and endpoint descriptor being NULL.
Currently DMA channels are allocated and they remain allocated
even if there is no active data transfer. Added channel_release()
whenever there is no pending request.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently in case of MUSB DMA channel request failure we are not
clearing MUSB_RXCSR_DMAENAB, MUSB_RXCSR_H_AUTOREQ and
MUSB_RXCSR_AUTOCLEAR bits of MUSB RXCSR of MUSB DMA. Which is
causing failure in receipt of data packets in next transfer.
Fix is to disable the MUSB DMA mode and related bits incase of
DMA channel request fails
Signed-off-by: Mantesh Sarashetti <mantesh@ti.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Control transfers with data expected from device to host will use usb_rcvctrlpipe()
for urb->pipe so for such urbs 'is_in' will be set causing control urb to fall
into the first "if" condition in musb_cleanup_urb().
Fixed by adding logic to check for non control endpoints.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
TXMAXP register is not getting programmed correctly for a full speed device
as can_bulk_split() have been removed by
"0662481: usb: musb: disable double buffering when it's broken" patch.
Adding back the case for can_bulk_split() to fix the reset message seen with
a full speed stick.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up
Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Variable d is a struct usb_iso_packet_descriptor. The status filed is usually
negative when an error happens.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_ep_program() contains obviously duplicate check for 'dma_channel' in its
IN/receive path -- removing it allows to save one level of indentation. While
at it, improve the comment style...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:
Documentation/dynamic-debug-howto.txt
for information on how to use that great
infrastructure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.
Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The convention is to prefix symbols exported from the USB HCD core with
"usb_hcd". This change makes unmap_urb_setup_for_dma() and
unmap_urb_for_dma() consistent with that.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We know that blackfin doesn't support double
buffering feature as of today. So we add a
flag set by musb_platform_init() to forcefully
disable that feature.
Such flag is created and marked as deprecated
to force us to find a solution for the missing
double buffering support on blackfin.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for MUSB Host DMA transfers greater than max
channel length, so that such transfers won't be truncated.
Signed-off-by: Anil Shetty <anil@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB stack maps the buffer for DMA if the controller supports DMA.
MUSB controller can perform DMA as well as PIO transfers.
The buffer needs to be unmapped before CPU can perform
PIO data transfers.
Export unmap_urb_for_dma() so that drivers can perform
the DMA unmapping in a sane way.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the issue which was observed while transfering
a large file ( > 20MB) over USB (OMAP MUSB controller acts as USB host)
to an attached USB thumb drive.
It was found that CDB field of CBW packet was set to 0x0. This was
due to missing a barrier before DMA engine starts transfer.
This buffer is allocated using dma_alloc_coherent which gives
non-cacheble but bufferable memory and hence needed a write
memory barrier to flush the write buffer.
More info on this thread is here:
http://www.spinics.net/lists/linux-omap/msg33987.html
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We assign "urb->hcpriv = qh;" a few lines down. I'm pretty sure we
want it "urb->hcpriv" to be NULL not a freed value.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit "usb: musb: Fix for isochronous IN transfer" (f82a689fa)
seems to have been against an older kernel version. It uses the old style
naming of variables. Unfortunately, this breaks building for most MUSB
users out there since "bDesiredMode" has been renamed to "desired_mode".
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying to use double buffer modes in RTL versions <2.0 may result in
infinite hangs or data corruption. So avoid them with older versions.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the work around for a Mentor controller related
bug where it's observed a BULK Tx toggle error on the bus when a
BULK IO gets scheduled on an endpoint that was earlier used for
handling ISOC transaction and needed to start on 1 toggle. When such
a situation arises even if the TXCSR toggle bits are programmed
correctly by the musb driver the data gets transmitted with 0 toggle
which leads to toggle error on the bus and the BULK transaction fails.
In case of MSC write, the device gets reset by the Host.
This Mentor bug is observed on almost all Mentor versions (1.3, 1.5,
1.8). Confirmed on DM644x, DM355, DM365, OMAPL13x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/musb/musb_host.c:1642:9: warning: symbol 'status' shadows an earlier one
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
