Retrieve BD address from the local-bd-address property.
This address must be unique and is usually added in the DT
by the bootloader which has access to the provisioned data.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the hdev setup function since wcnss-bt does not have
persistent memory to store an allocated BD address. The device is therefore
marked as unconfigured if no BD address has been previously retrieved.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The Broadcom controller on the Raspberry Pi3 sends an empty packet with
packet type 0x00 after launching the firmware. This will cause logging
of errors.
Bluetooth: hci0: Frame reassembly failed (-84)
Since this seems to be an intented behaviour of the controller, handle
it gracefully by parsing that empty packet with packet type 0x00 and
then just simply report it as diagnostic packet.
With that change no errors are logging and the packet itself is actually
recorded in the Bluetooth monitor traces.
< HCI Command: Broadcom Launch RAM (0x3f|0x004e) plen 4
Address: 0xffffffff
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Launch RAM (0x3f|0x004e) ncmd 1
Status: Success (0x00)
= Vendor Diagnostic (len 0)
< HCI Command: Broadcom Update UART Baud Rate (0x3f|0x0018) plen 6
00 00 00 10 0e 00 ......
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Update UART Baud Rate (0x3f|0x0018) ncmd 1
Status: Success (0x00)
< HCI Command: Reset (0x03|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
Status: Success (0x00)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.
Tested/compatible with bcm43438 (RPi3).
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commands that read the basic vendor information about the Broadcom
controller are duplicated for UART and USB devices. Combine them into a
single function to reduce the code complexity.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Not all Broadcom controller support the 4Mbps operational speed on UART
devices. This is because the UART clock setting changes might not be
supported.
< HCI Command: Broadcom Write UART Clock Setting (0x3f|0x0045) plen 1
01 .
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Write UART Clock Setting (0x3f|0x0045) ncmd 1
Status: Unknown HCI Command (0x01)
To support any operational speed higher than 3Mbps, support for this
command is required. With that respect it is better to not enforce any
operational speed by default. Only when its support is known, then allow
for higher operational speed.
This patch assigns the 4Mbps opertional speed only for devices
discovered through ACPI and leave all others at the default 115200.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
BT-Controller connected as platform non-root-hub device and
usb-driver initialize such device with wakeup disabled,
Ref. usb_new_device().
At present wakeup-capability get enabled by hid-input device from usb
function driver(e.g. BT HID device) at runtime. Again some functional
driver does not set usb-wakeup capability(e.g LE HID device implement
as HID-over-GATT), and can't wakeup the host on USB.
Most of the device operation (such as mass storage) initiated from host
(except HID) and USB wakeup aligned with host resume procedure. For BT
device, usb-wakeup capability need to enable form btusc driver as a
generic solution for multiple profile use case and required for USB remote
wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature
need to enable/disable with HCI interface up and down.
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the activity LED is solid on during continuous activity.
Blink the LED during continuous activity to match Windows driver
behavior.
Cards with activity LED:
power LED = solid on when up, off when down
activity LED = blinking during activity, off when idle
Cards without activity LED:
power LED = solid on when up, off when down, blinking during activity
(don't have such a card so I don't know if Windows driver does the same
thing)
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Keep power LED on during activity.
LED timer races with power LED disabling in hci_close(), resulting in
power LED left on after closing.
Stop LED timer before disabling power LED.
BTW. On cards without an activity LED, the behavior is a bit weird:
The LED is on after hci_open() but only until the first data transfer.
Then it's off in idle and on during activity.
It could be improved by keeping the LED on in idle and flashing during
activity.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Anycom CF-300 (HP C8249A) has both power and activity LEDs.
However the id read in bluecard_open() is 0x73 so the driver does not
enable the LEDs.
Remove the CARD_HAS_PCCARD_ID check to enable LEDs.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Force alignment value to the default one (1 byte) if uninitialized.
This fixes hci_ll serdev driver (alignment = 0) and avoid any further
issues with upcoming drivers.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We accidentally return success if the kmemdup() fails. It results in
a NULL dereference in the caller.
Fixes: 1110a2dbe6 ("Bluetooth: btrtl: Add RTL8822BE Bluetooth device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Nokia devices require the setup of its Public Bluetooth Device
Address and for that it is required to depend on vendor specific
commands. For Broadcom based Nokia devices, that is part of btbcm
module and can be selected via BT_BCM config option.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently we are calling usb_submit_urb directly to submit deferred tx
urbs after unanchor them.
So the usb_giveback_urb_bh would failed to unref it in usb_unanchor_urb
and cause memory leak:
unreferenced object 0xffffffc0ce0fa400 (size 256):
...
backtrace:
[<ffffffc00034a9a8>] __save_stack_trace+0x48/0x6c
[<ffffffc00034b088>] create_object+0x138/0x254
[<ffffffc0009d5504>] kmemleak_alloc+0x58/0x8c
[<ffffffc000345f78>] __kmalloc+0x1d4/0x2a0
[<ffffffc0006765bc>] usb_alloc_urb+0x30/0x60
[<ffffffbffc128598>] alloc_ctrl_urb+0x38/0x120 [btusb]
[<ffffffbffc129e7c>] btusb_send_frame+0x64/0xf8 [btusb]
Put those urbs in tx_anchor to avoid the leak, and also fix the error
handling.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed alignment of all block comments.
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove unnecessary static on local variable hst.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the object file size.
This issue was detected using Coccinelle and the
following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the object file size.
This log is the output of the size command, before and after the code
change:
before:
text data bss dec hex filename
4029 2528 128 6685 1a1d drivers/bluetooth/btwilink.o
after:
text data bss dec hex filename
4007 2472 64 6543 198f drivers/bluetooth/btwilink.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Convert hci_ll to use hci_uart_unregister_device().
This simplifies the _remove() handler as well as fixes a
potential race condition on unload.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabor.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Several drivers have the same (and incorrect) code in their
_remove() handler.
Coalesce this into a shared function.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's been numerous reported instances where BTUSB_QCA_ROME
bluetooth controllers stop functioning upon resume from suspend. These
devices seem to be losing power during suspend. Patch will detect a status
change on resume and perform a reset.
Signed-off-by: Leif Liddy <leif.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
pm_runtime_disable() is called in the _close() handler.
Since we call the _close() handler on remove, there is no need to
call pm_runtime_disable() a second time.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only cancel any ongoing work after making sure, that no new work
can be scheduled. This fixes a race condition in the remove handler.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed this coding style erro
./drivers/bluetooth/btqca.c:84: ERROR: code indent should use tabs where possible
Signed-off-by: Joan Jani <igiann@hotmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of no IRQ resource associated to the bcm_device, requesting
IRQ should return an error in order to not enable low power mgmt.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
This patch adds the device ID for the bluetooth chip used in the
Broadcom BCM43430 SDIO WiFi / UART BT chip.
Successfully tested using Firmware version 0x0182
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reported-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Just like the T100TA the host-wake irq on the Asus T100CHI is
active low. Having a quirk for this is actually extra important on the
T100CHI as it ships with a bluetooth keyboard dock, which does not
work properly without this quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_bcm proto is able to operate without bcm platform device linked
to its uart port. In that case, firmware can be applied, but there is
no power operation (no gpio/irq resources mgmt).
However, the current implementation breaks this use case because of
reporting a ENODEV error in the bcm setup procedure if bcm_request_irq
fails (which is the case if no bcm device linked).
Fix this by removing bcm_request_irq error forwarding.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The structure hci_serdev_client_ops does not need to be in global scope
and is not modified, so make it static.
Cleans up sparse warning:
"symbol 'hci_serdev_client_ops' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Joe and Bjørn suggested that it'd be nicer to not have the
cast in the fairly common case of doing
*(u8 *)skb_put(skb, 1) = c;
Add skb_put_u8() for this case, and use it across the code,
using the following spatch:
@@
expression SKB, C, S;
typedef u8;
identifier fn = {skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Note that due to the "S", the spatch isn't perfect, it should
have checked that S is 1, but there's also places that use a
sizeof expression like sizeof(var) or sizeof(u8) etc. Turns
out that nobody ever did something like
*(u8 *)skb_put(skb, 2) = c;
which would be wrong anyway since the second byte wouldn't be
initialized.
Suggested-by: Joe Perches <joe@perches.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assingment if ->probe() fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to manage the external clock provided to the WiLink combo chip
as it's needed for any of the transport interfaces.
To avoid breaking platforms not yet specifying the external clock, we make
it optional. In case the clock is successfully fetched during ->probe(),
let's manage it via the ->open|close() callbacks, to make sure the device
get properly powered on/off.
Fixes: ea45267873 ("arm64: dts: hikey: Fix WiFi support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add compatible values for WiLink chips from 128x and 180x series.
Also the DT binding already contained compatible values for the 127x
series, but the driver did not. This brings the list on par with
the list from wlcore (the wifi driver).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The caller (hci_core) still owns the skb in case of error, releasing
it inside the send function can lead to use-after-free errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When __hci_cmd_sync() fails, download_firmware() should also fail, and
the same error value should be returned as PTR_ERR(skb).
Without this fix, download_firmware() will return a success when it actually
failed in __hci_cmd_sync().
Fixes: 371805522f ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We see the following build failure with CONFIG_BT_HCIUART_NOKIA=y and
CONFIG_BT_HCIUART_H4=n:
drivers/bluetooth/hci_nokia.c: In function 'nokia_recv':
drivers/bluetooth/hci_nokia.c:644:18: error: implicit declaration of function 'h4_recv_buf' [-Werror=implicit-function-declaration]
...
Fix this by selecting the BT_HCIUART_H4 symbol like all the other users
of the protocoll.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_UART_PROTO_READY is in the set state, the Data Link protocol
layer (proto) is bound to the HCI UART driver. This state allows the
registered proto function pointers to be used by the HCI UART driver.
When unbinding (closing) the Data Link protocol layer, the proto
function pointers much be prevented from being used immediately before
running the proto close function pointer. Otherwise, there is a risk
that a proto non-close function pointer is used during or after the
proto close function pointer is used. The consequences are likely to
be a kernel crash because the proto close function pointer will free
resources used in the Data Link protocol layer.
Therefore, add a reader writer lock (rwlock) solution to prevent the
close proto function pointer from running by using write_lock_irqsave()
whilst the other proto function pointers are protected using
read_lock(). This means HCI_UART_PROTO_READY can safely be cleared
in the knowledge that no proto function pointers are running.
When flag HCI_UART_PROTO_READY is put into the clear state,
proto close function pointer can safely be run. Note
flag HCI_UART_PROTO_SET being in the set state prevents the proto
open function pointer from being run so there is no race condition
between proto open and close function pointers.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We see the following link error with CONFIG_BT_HCIUART=y,
CONFIG_BT_HCIUART_LL=y and CONFIG_SERIAL_DEV_BUS=m:
drivers/built-in.o: In function 'll_close':
supp.c:(.text+0x55add4): undefined reference to 'serdev_device_close'
supp.c:(.text+0x55add4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_close'
drivers/built-in.o: In function 'll_open':
supp.c:(.text+0x55aed0): undefined reference to 'serdev_device_open'
supp.c:(.text+0x55aed0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_open'
drivers/built-in.o: In function `hci_ti_probe':
supp.c:(.text+0x55b00c): undefined reference to 'hci_uart_register_device'
supp.c:(.text+0x55b00c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'hci_uart_register_device'
drivers/built-in.o: In function `ll_setup':
supp.c:(.text+0x55b08c): undefined reference to 'serdev_device_set_flow_control'
supp.c:(.text+0x55b08c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_set_flow_control'
supp.c:(.text+0x55b324): undefined reference to 'serdev_device_set_baudrate'
supp.c:(.text+0x55b324): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'serdev_device_set_baudrate'
drivers/built-in.o: In function 'll_init':
supp.c:(.init.text+0x1b508): undefined reference to '__serdev_device_driver_register'
supp.c:(.init.text+0x1b508): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol '__serdev_device_driver_register'
Fix this by dependig BT_HCIUART_LL on the BT_HCIUART_SERDEV symbol.
This implies a dependency on BT_HCIUART and hci_ll.c is only compiled in
if SERIAl_DEV_BUS is built in or SERIAL_DEV_BUS and BT_HCIUART are
modules.
Fixes: 371805522f ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before attempting to schedule a work-item onto hu->write_work in
hci_uart_tx_wakeup(), check that the Data Link protocol layer is
still bound to the HCI UART driver.
Failure to perform this protocol check causes a race condition between
the work queue hu->write_work running hci_uart_write_work() and the
Data Link protocol layer being unbound (closed) in hci_uart_tty_close().
Note hci_uart_tty_close() does have a "cancel_work_sync(&hu->write_work)"
but it is ineffective because it cannot prevent work-items being added
to hu->write_work after cancel_work_sync() has run.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_tx_wakeup()
which prevents scheduling of the work queue when HCI_UART_PROTO_READY
is in the clear state. However, note a small race condition remains
because the hci_uart_tx_wakeup() thread can run in parallel with the
hci_uart_tty_close() thread so it is possible that a schedule of
hu->write_work can occur when HCI_UART_PROTO_READY is cleared. A complete
solution needs locking of the threads which is implemented in a future
commit.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before attempting to dequeue a Data Link protocol encapsulated message,
check that the Data Link protocol is still bound to the HCI UART driver.
This makes the code consistent with the usage of the other proto
function pointers.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_dequeue()
and return NULL if the Data Link protocol is not bound.
This is needed for robustness as there is a scheduling race condition.
hci_uart_write_work() is scheduled to run via work queue hu->write_work
from hci_uart_tx_wakeup(). Therefore, there is a delay between
scheduling hci_uart_write_work() to run and hci_uart_dequeue() running
whereby the Data Link protocol layer could become unbound during the
scheduling delay. In this case, without the check, the call to the
unbound Data Link protocol layer dequeue function can crash.
It is noted that hci_uart_tty_close() has a
"cancel_work_sync(&hu->write_work)" statement but this only reduces
the window of the race condition because it is possible for a new
work-item to be added to work queue hu->write_work after the call to
cancel_work_sync(). For example, Data Link layer retransmissions can
be added to the work queue after the cancel_work_sync() has finished.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before attempting to send a HCI message, check that the Data Link
protocol is still bound to the HCI UART driver. This makes the code
consistent with the usage of the other proto function pointers.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_send_frame()
and return -EUNATCH if the Data Link protocol is not bound.
This also allows hci_send_frame() to report the error of an unbound
Data Link protocol layer. Therefore, it assists with diagnostics into
why HCI messages are being sent when the Data Link protocol is not
bound and avoids potential crashes.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ensure that HCI_UART_PROTO_READY is cleared before close(hu) is
called which closes the Data Link protocol layer.
Therefore, add the missing bit clear of HCI_UART_PROTO_READY to
hci_uart_init_work() so that the flag is cleared when
hci_register_dev fails.
Without the fix, the functions of the Data Link protocol layer could
potentially be accessed after that layer has been closed. This
could lead to a crash as memory would have been freed in that layer.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_register_dev() fails, hu->hdev should be set to NULL before
freeing hdev. This avoids potential use of hu->hdev after it has been
freed.
This commit sets hu->hdev to NULL before calling hci_free_dev() in error
handling scenarios in hci_uart_init_work() and hci_uart_register_dev().
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If hci_register_dev() returns an error in hci_uart_init_work()
then the HCI_UART_REGISTERED bit gets erroneously set due to
a missing return statement. Therefore, add the missing return
statement.
The consequence of the missing return is that the HCI UART is not
registered but HCI_UART_REGISTERED is set which allows the code
to think that hu->hdev is safe to access but hu->hdev has been
freed so could lead to a crash.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With CONFIG_SERIAL_DEV_BUS=m, the hci_serdev.o file does not actually
get built into hci_uart.o as the Makefile doesn't pick it up, leading
to a link error with anything referring to it:
ERROR: "hci_uart_register_device" [drivers/bluetooth/hci_nokia.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
Changing this in the Makefile would cause another problem when
hci_uart itself is built-in and cannot reference symbols from the
serdev module.
This tries to address both problems by introducing a new hidden
Kconfig symbol that controls both the compilation of hci_serdev.o
and whether the Nokia driver can be selected. This seems to address
the problem for me, though there might be a better way to do it.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid NULL pointer dereference occurring due to freeing
skb containing an error pointer. It can easily be triggered
by using the driver with broken uart (i.e. due to misconfigured
pinmuxing).
Fixes: 371805522f ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Turns out that the LL protocol and the TI-ST are the same thing AFAICT.
The TI-ST adds firmware loading, GPIO control, and shared access for
NFC, FM radio, etc. For now, we're only implementing what is needed for
BT. This mirrors other drivers like BCM and Intel, but uses the new
serdev bus.
The firmware loading is greatly simplified by using existing
infrastructure to send commands. It may be a bit slower than the
original code using synchronous functions, but the real bottleneck is
likely doing firmware load at 115.2kbps.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are no users of hci_uart_init_tty, so remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a driver for the Nokia H4+ protocol, which is used
at least on the Nokia N9, N900 & N950.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For bluetooth protocol driver only supporting serdev it makes
sense to follow common practice and built them into their own
module.
Such modules need access to hci_uart_register_device and
hci_uart_tx_wakeup for using the common protocol helpers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device driver may need to communicate with the UART
device while the Bluetooth device is closed (e.g. due
to interrupts).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds library functions for serdev based BT drivers. This is largely
copied from hci_ldisc.c and modified to use serdev calls. There's a little
bit of duplication, but I avoided intermixing this as the ldisc code should
eventually go away.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
[Fix style issues reported by Pavel]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This will be used by Nokia's H4+ protocol, which
uses 2-byte aligned packets.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sanity check of interrupt number in interrupt handler is unnecessary and
confusion, remove it.
Reported-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 74cdad37cd ("Bluetooth: hci_intel: Add runtime PM support")
Fixes: 1ab1f239bf ("Bluetooth: hci_intel: Add support for platform driver")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 0395ffc1ee ("Bluetooth: hci_bcm: Add PM for BCM devices")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Else is not generally useful after a break or return
Signed-off-by: Prasanna Karthik <pkarthik@outlook.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Until now the driver supports only ACPI enumeration. Nevertheless
Intel Edison SoM has Broadcom Wi-Fi + BT chip and neither ACPI nor DT
enumeration mechanism.
Enable pure platform driver in order to support Intel Edison SoM.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The message concerning missing config files for 8723b, 8821a, and
8761a should have been issued with BT_INFO() rather than BT_ERR() as
this condition is not fatal. After looking at that code, I have
reworked the logic to log such messages only if the device needs such a
config file. At the moment, only the 8822b fits that description.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: 陆朱伟 <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Intel Bluetooth device 9160/9260 also
known as ThunderPeak(ThP) for UART.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
This patch uses a hw_variant value read from the device during
runtime to form the firmware filenames instead of using a constant
value, so it can support multiple prouducts.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Multiple new hardware variants are planned and the simple if statement
would get really complicated and unreadable. So instead replace it with
a simple switch statement.
The change is applied to both USB and UART.
Based-on-patch-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_bcm driver currently does not prepare/unprepare the clock and
goes directly to enable, but as the documentation for clk_enable says,
clk_prepare must be called before clk_enable.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
trivial fix to spelling mistake in debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By moving these client drivers to use RPMSG instead of the direct SMD
API we can reuse them ontop of the newly added GLINK wire-protocol
support found in the 820 and 835 Qualcomm platforms.
As the new (RPMSG-based) and old SMD implementations are mutually
exclusive we have to change all client drivers in one commit, to make
sure we have a working system before and after this transition.
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile-testing fails when QCOM_SMD is a loadable module:
drivers/bluetooth/built-in.o: In function `btqcomsmd_send':
btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send'
drivers/bluetooth/built-in.o: In function `btqcomsmd_probe':
btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel'
btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata'
This clarifies the dependency to allow compile-testing only when
SMD is completely disabled, otherwise the dependency on QCOM_SMD
will make sure we can link against it.
Fixes: e27ee2b16b ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
trivial fix to spelling mistake in error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
trivial fix to spelling mistake in BT_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver only has runtime but no build time dependency with QCOM_SMD &&
QCOM_WCNSS_CTRL. So it can be built for testing purposes if COMPILE_TEST
option is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM2E96 ID is used by the ECS EF20 laptop, and BCM2E95 is present
in the Weibu F3C. Both are now logged as:
hci0: BCM: chip id 82
hci0: BCM43341B0 (002.001.014) build 0000
hci0: BCM (002.001.014) build 0158
The ECS vendor kernel predates the host-wakeup support in hci_bcm but
it explicitly has a comment saying that the GPIO assignment needs to be
reordered for BCM2E96:
1. (not used in vendor driver)
2. Device wakeup
3. Shutdown
For both devices in question, the DSDT has these GPIOs listed in order
of GpioInt, GpioIo, GpioIo. And if we use the first one listed (GpioInt)
as the host wakeup, that interrupt handler fires while doing bluetooth
I/O.
I am assuming the convention of GPIO ordering has been changed for these
new device IDs, so lets use the new ordering on such devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some btbcm devices require more time to complete its reset process.
They won't reply any hci command until reset is done.
[ 17.218554] Bluetooth: hci0 command 0x1001 tx timeout
[ 25.214999] Bluetooth: hci0: BCM: Reading local version info failed (-110)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The irq_of_parse_and_map will return 0 as a invalid irq.
Set irq_bt to -1 in this case, so that the btmrvl resume/suspend code
would not try to enable/disable it.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's much the same as what we did for mwifiex in:
b9da4d2 mwifiex: avoid double-disable_irq() race
"We have a race where the wakeup IRQ might be in flight while we're
calling mwifiex_disable_wake() from resume(). This can leave us
disabling the IRQ twice.
Let's disable the IRQ and enable it in case if we have double-disabled
it."
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Marvell devices may have many gpio pins, and hence for wakeup
on these out-of-band pins, the chip needs to be told which pin is
to be used for wakeup, using an hci command.
Thus, we read the pin number etc from the device tree node and send
a command to the chip.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some onboard BT chips (e.g. Marvell 8997) contain a wakeup pin that
can be connected to a gpio on the CPU side, and can be used to wakeup
the host out-of-band. This can be useful in situations where the
in-band wakeup is not possible or not preferable (e.g. the in-band
wakeup may require the USB host controller to remain active, and
hence consuming more system power during system sleep).
The oob gpio interrupt to be used for wakeup on the CPU side, is
read from the device tree node, (using standard interrupt descriptors).
A devcie tree binding document is also added for the driver. The
compatible string is in compliance with
Documentation/devicetree/bindings/usb/usb-device.txt
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use a label to remove the repetetive cleanup, for error cases.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/bluetooth/btqcomsmd.ko | grep alias
$
After this patch:
$ modinfo drivers/bluetooth/btqcomsmd.ko | grep alias
alias: of:N*T*Cqcom,wcnss-btC*
alias: of:N*T*Cqcom,wcnss-bt
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
copy_from_iter_full(), copy_from_iter_full_nocache() and
csum_and_copy_from_iter_full() - counterparts of copy_from_iter()
et.al., advancing iterator only in case of successful full copy
and returning whether it had been successful or not.
Convert some obvious users. *NOTE* - do not blindly assume that
something is a good candidate for those unless you are sure that
not advancing iov_iter in failure case is the right thing in
this case. Anything that does short read/short write kind of
stuff (or is in a loop, etc.) is unlikely to be a good one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Probe functions should return 0 on success. This driver's probe
returns the value returned by hci_register_dev(), which is the hci
index. This works for systems with only one hci device (id = 0) but
for systems where the btwilink device ends up with an id larger than
0, things will start to fall apart.
Make the probe function return 0 on success.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ACPI table for BCM2E55 of Lenovo ThinkPad 8 is not correct.
Set correctly IRQ polarity for this device, fixing the issue of bluetooth
never resuming after autosuspend PM.
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move usb_autopm_get_interface() ahead of setup_on_usb() to prevent
device from sending usb control message in usb suspend mode.
The error message is as below:
[ 83.944103] btusb 1-2:1.1: usb_suspend_interface: status 0
[ 83.944107] btusb 1-2:1.0: usb_suspend_interface: status 0
[ 83.960132] usb 1-2: usb auto-suspend, wakeup 0
[ 83.976156] usb 1-2: usb_suspend_device: status 0
[ 83.976162] usb 1-2: usb_suspend_both: status 0
[ 298.689106] Bluetooth: hci0
[ 298.689399] Bluetooth: hci0: Failed to access otp area (-113)
Signed-off-by: Ethan Hsieh <ethan.hsieh@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btusb_set_bdaddr_marvell() configures BD address for Marvell chipsets.
This patch adds new chipset 8997 in the list so that BD address feature
would be available for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
Here is the big USB, and PHY, and extcon, patchsets for 4.9-rc1.
Full details are in the shortlog, but generally a lot of new hardware
support, usb gadget updates, and Wolfram's great cleanup of USB error
message handling, making the kernel image a tad bit smaller.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNTEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspbuUAoJAn
XD6k9A+0QgnJ/iLiT8pztawNAKCCVYZOzgdFRGsnaZ2p7lb9IHpPCA==
=QUj+
-----END PGP SIGNATURE-----
Merge tag 'usb-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull usb/phy/extcon updates from Greg KH:
"Here is the big USB, and PHY, and extcon, patchsets for 4.9-rc1.
Full details are in the shortlog, but generally a lot of new hardware
support, usb gadget updates, and Wolfram's great cleanup of USB error
message handling, making the kernel image a tad bit smaller.
All of this has been in linux-next with no reported issues"
* tag 'usb-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (343 commits)
Revert "usbtmc: convert to devm_kzalloc"
USB: serial: cp210x: Add ID for a Juniper console
usb: Kconfig: using select for USB_COMMON dependency
bluetooth: bcm203x: don't print error when allocating urb fails
mmc: host: vub300: don't print error when allocating urb fails
usb: hub: change CLEAR_FEATURE to SET_FEATURE
usb: core: Introduce a USB port LED trigger
USB: bcma: drop Northstar PHY 2.0 initialization code
usb: core: hcd: add missing header dependencies
usb: musb: da8xx: fix error handling message in probe
usb: musb: Fix session based PM for first invalid VBUS
usb: musb: Fix PM runtime for disconnect after unconfigure
musb: Export musb_root_disconnect for use in modules
usb: misc: legousbtower: Fix NULL pointer deference
cdc-acm: hardening against malicious devices
Revert "usb: gadget: NCM: Protect dev->port_usb using dev->lock"
include: extcon: Fix compilation error caused because of incomplete merge
MAINTAINERS: add tree entry for USB Serial
phy-twl4030-usb: initialize charging-related stuff via pm_runtime
phy-twl4030-usb: better handle musb_mailbox() failure
...
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove multiple return statements in hci_uart_tty_ioctl() call and
added a single return statement.
This code re-organisation allows subsequent locking to be easily
added.
Signed-off-by: Vignesh Raman <Vignesh_Raman@mentor.com>
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Rajeev Kumar <rajeev_kumar@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Send an ACK frame with the current txack value in response to
every received reliable frame unless a TX reliable frame is being
sent. This modification allows re-transmitted frames from the remote
peer to be acknowledged rather than ignored. It means that the remote
peer knows which frame number to start re-transmitting from.
Without this modification, the recovery time to a missing frame
from the remote peer was unnecessarily being extended because the
headers of the out of order reliable frames were being discarded rather
than being processed. The frame headers of received frames will
indicate whether the local peer's transmissions have been
acknowledged by the remote peer. Therefore, the local peer may
unnecessarily re-transmit despite the remote peer already indicating
that the frame had been acknowledged in out of order reliable frame.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Rajeev Kumar <rajeev_kumar@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
drivers/bluetooth/hci_bcsp.c contains some style issues as
highlighted by
./scripts/checkpatch.pl --strict -f drivers/bluetooth/hci_bcsp.c
a) comments - maintainer prefers network style comments
b) positioning of lines in multi-line statements
c) spaces after casts
d) missing blank lines after declarations
Therefore, tidy-up the above to make it easier to apply
future code changes that have conforming style.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Running with KASAN produces some messages:
BUG: KASAN: use-after-free in ti_st_send_frame+0x9c/0x16c at addr
ffffffc064868fe8
Read of size 1 by task kworker/u17:1/1266
<KASAN output trimmed>
Hardware name: HiKey Development Board (DT)
Workqueue: hci0 hci_cmd_work
Call trace:
[<ffffffc00008c00c>] dump_backtrace+0x0/0x178
[<ffffffc00008c1a4>] show_stack+0x20/0x28
[<ffffffc00067da38>] dump_stack+0xa8/0xe0
[<ffffffc000288430>] print_trailer+0x110/0x174
[<ffffffc00028aedc>] object_err+0x4c/0x5c
[<ffffffc00028f714>] kasan_report_error+0x254/0x54c
[<ffffffc00028fa70>] kasan_report+0x64/0x70
[<ffffffc00028eb8c>] __asan_load1+0x4c/0x54
[<ffffffc000b59b24>] ti_st_send_frame+0x9c/0x16c
[<ffffffc000ee8dcc>] hci_send_frame+0xb4/0x118
[<ffffffc000ee8efc>] hci_cmd_work+0xcc/0x154
[<ffffffc0000f6c48>] process_one_work+0x26c/0x7a4
[<ffffffc0000f721c>] worker_thread+0x9c/0x73c
[<ffffffc000100250>] kthread+0x138/0x154
[<ffffffc000085c50>] ret_from_fork+0x10/0x40
The packet is being accessed for statistics after it has been freed.
Save the packet type before sending for statistics afterwards.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces support for Marvell Bluetooth controller over
UART (8897 for now). In order to send the final firmware at full speed,
a helper firmware is firstly sent. Firmware download is driven by the
controller which sends request firmware packets (including expected
size).
This driver is a global rework of the one proposed by
Amitkumar Karwar <akarwar@marvell.com>.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The RTL8822BE is a new Realtek wifi and BT device. Support for the BT
part is hereby added.
As this device is similar to most of the other Realtek BT devices, the
changes are minimal. The main difference is that the 8822BE needs a
configuration file for enabling and disabling features. Thus code is
added to select and load this configuration file. Although not needed
at the moment, hooks are added for the other devices that might need
such configuration files.
One additional change is to the routine that tests that the project
ID contained in the firmware matches the hardware. As the project IDs
are not sequential, continuing to use the position in the array as the
expected value of the ID would require adding extra unused entries in
the table, and any subsequant rearrangment of the array would break the
code. To fix these problems, the array elements now contain both the
hardware ID and the expected value for the project ID.
Signed-off-by: 陆朱伟 <alex_lu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
edl->data is an array of __u8 so the null check is unneccessary,
so remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The workqueue "workqueue" queues multiple work items viz &qca->ws_awake_rx
&qca->ws_rx_vote_off, &qca->ws_awake_device, &qca->ws_tx_vote_off which
require strict execution ordering. Hence, an ordered dedicated workqueue
has been used to replace the deprecated create_singlethread_workqueue
instance.
WQ_MEM_RECLAIM has not been set since the driver is not being used on a
memory reclaim path.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The newly added bluetooth driver is based on the soc-specific support,
but lacks the obvious compile-time dependency on that:
drivers/bluetooth/btqcomsmd.o: In function `btqcomsmd_probe':
btqcomsmd.c:(.text.btqcomsmd_probe+0x40): undefined reference to `qcom_wcnss_open_channel'
btqcomsmd.c:(.text.btqcomsmd_probe+0x5c): undefined reference to `qcom_wcnss_open_channel'
Makefile:969: recipe for target 'vmlinux' failed
Fixes: 90c107dc8b2c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
wait_on_bit_timeout() returns one of the following three values:
* 0 to indicate success.
* -EINTR to indicate that a signal has been received;
* -EAGAIN to indicate timeout;
Make the wait_on_bit_timeout() callers check for these values.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Qualcomm WCNSS chip provides two SMD channels to the BT core; one
for command and one for event packets. This driver exposes the two
channels as a hci device.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes module_init()/module_exit() from driver code by using
module_misc_device() macro. All modules in this patch has a print
statement which is removed when module_misc_device() macro is used.
If undesirable this patch can be dropped entirely, this is the only
purpose of making this as a separate patch.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is_suspending flag remains on when host sleep fails to enable. Data
path is unnecessarily blocked after this. This patch ensures to
reset the flag in failure path.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Digianswer sniffer devices allow for reading a firmware specific
information string. If it is available, then inform the Bluetooth core
about it via hci_set_fw_info. That exposes it via debugfs like this:
# cat /sys/kernel/debug/bluetooth/hci0/firmware_info
SNIF_102,BB930,02/01/18,10:37:56
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
On mips and parisc:
drivers/bluetooth/btwilink.c: In function 'ti_st_open':
drivers/bluetooth/btwilink.c:174:21: warning: overflow in implicit constant conversion [-Woverflow]
hst->reg_status = -EINPROGRESS;
drivers/nfc/nfcwilink.c: In function 'nfcwilink_open':
drivers/nfc/nfcwilink.c:396:31: warning: overflow in implicit constant conversion [-Woverflow]
drv->st_register_cb_status = -EINPROGRESS;
There are actually two issues:
1. Whether "char" is signed or unsigned depends on the architecture.
As the completion callback data is used to pass a (negative) error
code, it should always be signed.
2. EINPROGRESS is 150 on mips, 245 on parisc.
Hence -EINPROGRESS doesn't fit in a signed 8-bit number.
Change the callback status from "char" to "int" to fix these.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LPM can be enabled via a DDC write command at specific DDC ID.
As any other DDC value, this is up to the DDC config file to
include (or not) the low power mode configuration.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With current btusb.ko kernel module, Bluetooth pretends to be active
but there is no real activity.
I'm using an Acer Aspire VN7-791.
Output of lsusb:
Bus 003 Device 007: ID 0489:e092 Foxconn / Hon Hai
On my laptop, this device is actually used as a combo with wifi chipset
Atheros Qualcomm Killer N1525 Wireless-AC [168c:003e],
* Fix by adding a declaration in kernel sources drivers/bluetooth/btusb.c
{ USB_DEVICE(0x0489, 0xe092), .driver_info = BTUSB_QCA_ROME },
* Compiled extra module /lib/modules/4.4.0-22-generic/extra/btusb.ko
* Successfully tested against my phone (obex file transfer)
Signed-off-by: Yvain THONNART <yvain.thonnart@m4x.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Kasan reported slab-out-of-bounds access in btmrvl_sdio:
[ 33.055400] ==================================================================
[ 33.062585] BUG: KASAN: slab-out-of-bounds in memcpy+0x24/0x50 at addr ffffffc0d89b4a00
[ 33.070529] Read of size 256 by task btmrvl_main_ser/3576
[ 33.075885] =============================================================================
[ 33.084002] BUG kmalloc-256 (Tainted: G B ): kasan: bad access detected
[ 33.091511] -----------------------------------------------------------------------------
<snip...>
[ 33.413498] Call trace:
[ 33.415928] [<ffffffc00020a440>] dump_backtrace+0x0/0x190
[ 33.421288] [<ffffffc00020a5ec>] show_stack+0x1c/0x28
[ 33.426305] [<ffffffc000b3288c>] dump_stack+0xa0/0xf8
[ 33.431320] [<ffffffc000396130>] print_trailer+0x158/0x16c
[ 33.436765] [<ffffffc0003962cc>] object_err+0x48/0x5c
[ 33.441780] [<ffffffc00039be24>] kasan_report+0x344/0x510
[ 33.447141] [<ffffffc00039afd8>] __asan_loadN+0x20/0x150
[ 33.452413] [<ffffffc00039b60c>] memcpy+0x20/0x50
[ 33.457084] [<ffffffc000595fcc>] swiotlb_tbl_map_single+0x2ec/0x310
[ 33.463305] [<ffffffc000596b54>] map_single+0x24/0x30
[ 33.468320] [<ffffffc0005970c8>] swiotlb_map_sg_attrs+0xec/0x21c
[ 33.474286] [<ffffffc000219d4c>] __swiotlb_map_sg_attrs+0x48/0xec
[ 33.480339] [<ffffffc0008ea610>] msdc_prepare_data.isra.11+0xf0/0x11c
[ 33.486733] [<ffffffc0008ecbd0>] msdc_ops_request+0x74/0xf0
[ 33.492266] [<ffffffc0008c6b38>] __mmc_start_request+0x78/0x8c
[ 33.498057] [<ffffffc0008c6d6c>] mmc_start_request+0x220/0x240
[ 33.503848] [<ffffffc0008c6e04>] mmc_wait_for_req+0x78/0x250
[ 33.509468] [<ffffffc0008d70fc>] mmc_io_rw_extended+0x2ec/0x388
[ 33.515347] [<ffffffc0008d8fc0>] sdio_io_rw_ext_helper+0x160/0x268
[ 33.521483] [<ffffffc0008d93fc>] sdio_writesb+0x40/0x50
[ 33.526677] [<ffffffbffc338b38>] btmrvl_sdio_host_to_card+0x124/0x1bc [btmrvl_sdio]
[ 33.534283] [<ffffffbffc3290a0>] btmrvl_service_main_thread+0x384/0x428 [btmrvl]
[ 33.541626] [<ffffffc0002518e8>] kthread+0x140/0x158
[ 33.546550] Memory state around the buggy address:
[ 33.551305] ffffffc0d89b4980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 33.558474] ffffffc0d89b4a00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.565643] >ffffffc0d89b4a80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fc
[ 33.572809] ^
[ 33.579889] ffffffc0d89b4b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 33.587055] ffffffc0d89b4b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 33.594221] ==================================================================
The cause of this is that btmrvl_sdio_host_to_card can access memory region
out of its allocated space due to:
1. the requested block size is smaller than SDIO_BLOCK_SIZE, and/or
2. the allocated memory is not BTSDIO_DMA_ALIGN-aligned.
This patch fixes the issue by allocating a buffer which is big enough for
SDIO_BLOCK_SIZE transfer and/or BTSDIO_DMA_ALIGN address relocation.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The format of Intel Bluetooth firmware filename for bootloader product
is ibt-<hw_variant>-<device_revision_id>.sfi
Currently the driver uses a constant value 11 (0x0b) for hw_variant
to support LnP/SfP product. But new product like WsP product has
a different value such as 12 (0x0c).
To support the multiple products, this patch replaces the constant
value of hw_variant to the actual hw_variant value read from
the device.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
gpiod_get_optional can return either ERR_PTR or NULL pointer.
NULL case is not tested and then dereferenced later in desc_to_gpio.
Fix this by using non optional version which returns ERR_PTR in any
error case (this is not an optional gpio).
Use the same non optional version for the host-wake gpio.
Fixes: 765ea3abd1 ("Bluetooth: hci_intel: Retrieve host-wake IRQ")
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some arm-based platforms, we need to configure platform specific
parameters by device tree node and also define our node as a child
node of parent SDIO host controller.
This patch parses these parameters from device tree. It includes
calibration data download to firmware, wakeup pin configured to firmware,
and soc specific wake up gpio, which will be set as wakeup interrupt pin.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We could print an uninitialized value in the error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_vhci driver creates a hci device object dynamically upon each
HCI_VENDOR_PKT write. Although it checks the already created object
and returns an error, it's still racy and may build multiple hci_dev
objects concurrently when parallel writes are performed, as the device
tracks only a single hci_dev object.
This patch introduces a mutex to protect against the concurrent device
creations.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both vhci_get_user and vhci_release race with open_timeout work. They
both contain cancel_delayed_work_sync, but do not test whether the
work actually created hdev or not. Since the work can be in progress
and _sync will wait for finishing it, we can have data->hdev allocated
when cancel_delayed_work_sync returns. But the call sites do 'if
(data->hdev)' *before* cancel_delayed_work_sync.
As a result:
* vhci_get_user allocates a second hdev and puts it into
data->hdev. The former is leaked.
* vhci_release does not release data->hdev properly as it thinks there
is none.
Fix both cases by moving the actual test *after* the call to
cancel_delayed_work_sync.
This can be hit by this program:
#include <err.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <unistd.h>
#include <sys/stat.h>
#include <sys/types.h>
int main(int argc, char **argv)
{
int fd;
srand(time(NULL));
while (1) {
const int delta = (rand() % 200 - 100) * 100;
fd = open("/dev/vhci", O_RDWR);
if (fd < 0)
err(1, "open");
usleep(1000000 + delta);
close(fd);
}
return 0;
}
And the result is:
BUG: KASAN: use-after-free in skb_queue_tail+0x13e/0x150 at addr ffff88006b0c1228
Read of size 8 by task kworker/u13:1/32068
=============================================================================
BUG kmalloc-192 (Tainted: G E ): kasan: bad access detected
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in vhci_open+0x50/0x330 [hci_vhci] age=260 cpu=3 pid=32040
...
kmem_cache_alloc_trace+0x150/0x190
vhci_open+0x50/0x330 [hci_vhci]
misc_open+0x35b/0x4e0
chrdev_open+0x23b/0x510
...
INFO: Freed in vhci_release+0xa4/0xd0 [hci_vhci] age=9 cpu=2 pid=32040
...
__slab_free+0x204/0x310
vhci_release+0xa4/0xd0 [hci_vhci]
...
INFO: Slab 0xffffea0001ac3000 objects=16 used=13 fp=0xffff88006b0c1e00 flags=0x5fffff80004080
INFO: Object 0xffff88006b0c1200 @offset=4608 fp=0xffff88006b0c0600
Bytes b4 ffff88006b0c11f0: 09 df 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c1200: 00 06 0c 6b 00 88 ff ff 00 00 00 00 00 00 00 00 ...k............
Object ffff88006b0c1210: 10 12 0c 6b 00 88 ff ff 10 12 0c 6b 00 88 ff ff ...k.......k....
Object ffff88006b0c1220: c0 46 c2 6b 00 88 ff ff c0 46 c2 6b 00 88 ff ff .F.k.....F.k....
Object ffff88006b0c1230: 01 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 ................
Object ffff88006b0c1240: 40 12 0c 6b 00 88 ff ff 40 12 0c 6b 00 88 ff ff @..k....@..k....
Object ffff88006b0c1250: 50 0d 6e a0 ff ff ff ff 00 02 00 00 00 00 ad de P.n.............
Object ffff88006b0c1260: 00 00 00 00 00 00 00 00 ab 62 02 00 01 00 00 00 .........b......
Object ffff88006b0c1270: 90 b9 19 81 ff ff ff ff 38 12 0c 6b 00 88 ff ff ........8..k....
Object ffff88006b0c1280: 03 00 20 00 ff ff ff ff ff ff ff ff 00 00 00 00 .. .............
Object ffff88006b0c1290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffff88006b0c12a0: 00 00 00 00 00 00 00 00 00 80 cd 3d 00 88 ff ff ...........=....
Object ffff88006b0c12b0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . ..............
Redzone ffff88006b0c12c0: bb bb bb bb bb bb bb bb ........
Padding ffff88006b0c13f8: 00 00 00 00 00 00 00 00 ........
CPU: 3 PID: 32068 Comm: kworker/u13:1 Tainted: G B E 4.4.6-0-default #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014
Workqueue: hci0 hci_cmd_work [bluetooth]
00000000ffffffff ffffffff81926cfa ffff88006be37c68 ffff88006bc27180
ffff88006b0c1200 ffff88006b0c1234 ffffffff81577993 ffffffff82489320
ffff88006bc24240 0000000000000046 ffff88006a100000 000000026e51eb80
Call Trace:
...
[<ffffffff81ec8ebe>] ? skb_queue_tail+0x13e/0x150
[<ffffffffa06e027c>] ? vhci_send_frame+0xac/0x100 [hci_vhci]
[<ffffffffa0c61268>] ? hci_send_frame+0x188/0x320 [bluetooth]
[<ffffffffa0c61515>] ? hci_cmd_work+0x115/0x310 [bluetooth]
[<ffffffff811a1375>] ? process_one_work+0x815/0x1340
[<ffffffff811a1f85>] ? worker_thread+0xe5/0x11f0
[<ffffffff811a1ea0>] ? process_one_work+0x1340/0x1340
[<ffffffff811b3c68>] ? kthread+0x1c8/0x230
...
Memory state around the buggy address:
ffff88006b0c1100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006b0c1180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88006b0c1200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88006b0c1280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff88006b0c1300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 23424c0d31 (Bluetooth: Add support creating virtual AMP controllers)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: stable 3.13+ <stable@vger.kernel.org>
HCI_UART_PROTO_SET flag is set before hci_uart_set_proto call. If we
receive data from tty layer during this procedure, proto pointer may
not be assigned yet, leading to null pointer dereference in rx method
hci_uart_tty_receive.
This patch fixes this issue by introducing HCI_UART_PROTO_READY flag in
order to avoid any proto operation before proto opening and assignment.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some case, the btmrvl_sdio firmware would fail to active within the
polling time. Increase the polling interval to 100 msec to fix the
issue.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Lenovo ThinkPad Tablet 8 with BCM43241 rev B5 chipset uses the BCM2E55
ACPI ID for Bluetooth. Add it to the list of supported devices.
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The AG6xx devices behave similar to Wilkens Peak and Stone Peak and with
that it is needed to check for Intel default address. In addition it is
possible to enable vendor events and diag support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This driver implements support for iBT2.1 Bluetooth controller embedded
in the AG620 communication combo. The controller needs to be configured
with bddata and can be patched with a binary patch file (pbn).
These operations are performed in manufacturing mode.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the call to request_firmware() fails in btbcm_setup_patchram(),
the BCM chip will be operating with its default firmware.
In this case, btbcm_setup_patchram() should not return immediately
but instead should skip to btbcm_check_bdaddr() and quirk setup.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recent macbooks (early 2015) with BCM43241 use this ACPI ID. Add it to the
list of supported devices.
Reported-by: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This ACPI ID is used at least by HP for their Omni 10 5600eg tablet.
Signed-off-by: J.J. Meijer <jjmeijer88@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A return value of the intel_wait_booting() function compared with
a constant ETIMEDOUT instead of -ETIMEDOUT.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed a coding style issue. Added a blank link after declaration.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Usually when driver sends data to firmware it receives TX_DONE
(DN_LD_HOST_INT_STATUS) interrupt from firmware right away.
It's also observed that some times the fireware could delay
sending DN_LD_HOST_INT_STATUS interrupt. If driver sends data to
firmware during suspend processing and the TX_DONE interrupt is
delayed, it may come back at wrong time when SDIO host driver is
in the middle of suspending.
Block any data from stack while suspending. Also skip sending
data that are already in driver tx_queue.
Don't purge the skb queue on suspend to avoid intermittent music
after system resumes from S3.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For gpio=0xff (wake up host through SDIO interface) case,
gap=0xff means no delay (same as gap=0) for incoming data packet
to be sent to host after host sleep is activated.
Change it to the maximum delay to reduce the chance that RX
interrupt could be delivered while host controller suspends.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These are used at least by Acer with BCM43241.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The IDs should all be for Broadcom BCM43241 module, and
hci_bcm is now the proper driver for them. This removes one
of two different ways of handling PM with the module.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
devm_kzalloc prints its own OOM message upon failure.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
devm_kzalloc prints its own OOM message upon failure.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add BCM2E65 device in acpi_device_id table used on Asus T100TAF.
Signed-off-by: Luka Karinja <luka.karinja@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initializing Configuration field in H5 Config message to 0x01 gives
wrong impression that the value is used and needed. Later on the whole
field is rewritten with h5_cfg_field().
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel Version Read command is used to retrieve information
about hardware and firmware version/revision of Intel Bluetooth
controllers. This is an Intel generic command used in USB and
UART drivers.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Older Intel controllers need to enter manufacturing mode to perform
some vendor specific operations (patching, configuration...).
Add enter/exit manufaturing methods and refactor existing
manufacturing code.
Exit can be configured to perform a reset. Reset can be performed
either with patches activated or deactivated.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the standard HCI_CMD_TIMEOUT(1s) for HCI command instead of
HCI_INIT_TIMEOUT(10s) which is not justified in these cases.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The N_HCI ldisc does not define a flush_buffer() ldisc method, so
the check when opening the ldisc is always false.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only Sliding Window Size is used at the moment for H5 Bluetooth
Configuration messages.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using hexadecimal notation for mask makes code easier to read
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes it easier to read and makes code consistent.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull networking fixes from David Miller:
1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.
2) Several spots need to get to the original listner for SYN-ACK
packets, most spots got this ok but some were not. Whilst covering
the remaining cases, create a helper to do this. From Eric Dumazet.
3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
from Rasmus Villemoes.
4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.
5) Use after free in mvneta driver, from Justin Maggard.
6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.
7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd
Bergmann.
8) Fix multicast getsockopt deadlock, from WANG Cong.
9) Fix deadlock in btusb, from Kuba Pawlak.
10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
counter state. From Sabrina Dubroca.
11) Fix packet_bind() race, which can cause lost notifications, from
Francesco Ruggeri.
12) Fix MAC restoration in qlcnic driver during bonding mode changes,
from Jarod Wilson.
13) Revert bridging forward delay change which broke libvirt and other
userspace things, from Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
Revert "bridge: Allow forward delay to be cfgd when STP enabled"
bpf_trace: Make dependent on PERF_EVENTS
qed: select ZLIB_INFLATE
net: fix a race in dst_release()
net: mvneta: Fix memory use after free.
net: Documentation: Fix default value tcp_limit_output_bytes
macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
mvneta: add FIXED_PHY dependency
net: caif: check return value of alloc_netdev
net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
drivers: net: xgene: fix RGMII 10/100Mb mode
netfilter: nft_meta: use skb_to_full_sk() helper
net_sched: em_meta: use skb_to_full_sk() helper
sched: cls_flow: use skb_to_full_sk() helper
netfilter: xt_owner: use skb_to_full_sk() helper
smack: use skb_to_full_sk() helper
net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
bpf: doc: correct arch list for supported eBPF JIT
dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
bonding: fix panic on non-ARPHRD_ETHER enslave failure
...
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_compatible_node(n, ...) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bt_skb_alloc() returns NULL on error, it never returns an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel Bluetooth controllers can emit extra vendor specific events in
error conditions or for debugging purposes. To make the life easier for
engineers, enable them by default. When the vendor_diag options has been
enabled, then additional debug events are also enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Intel bootloader devices, set the manufacturer information so that
it becomes possible to decode the boot process.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Provide an early indication about the manufacturer information so that
it can be forwarded into monitor channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the controllers from Intel and Broadcom (including Apple), it is
helpful to have the information about the manufacturer send out early.
This patch sets the hdev->manufacturer information which will be send
out before actually calling the vendor specific hdev->setup driver
callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
