This patch corrects the SPDX License Identifier style in
header files related to drivers for USB Network devices.
This patch gives an explicit block comment to the
SPDX License Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the use of SW timestamping.
ax88179_178a uses the usbnet transmit function usbnet_start_xmit() which
implements software timestamping. ax88179_178a overrides ethtool_ops but
missed to set .get_ts_info. This caused SOF_TIMESTAMPING_TX_SOFTWARE
capability to be not available.
Signed-off-by: Andreas K. Besslein <besslein.andreas@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.
1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().
For #1, use the same solution as commit 8481141246 ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both rtl_work_func_t() and rtl8152_close() call napi_disable().
Since the two calls aren't protected by a lock, if the close
function starts executing before the work function, we can get into a
situation where the napi_disable() function is called twice in
succession (first by rtl8152_close(), then by set_carrier()).
In such a situation, the second call would loop indefinitely, since
rtl8152_close() doesn't call napi_enable() to clear the NAPI_STATE_SCHED
bit.
The rtl8152_close() function in turn issues a
cancel_delayed_work_sync(), and so it would wait indefinitely for the
rtl_work_func_t() to complete. Since rtl8152_close() is called by a
process holding rtnl_lock() which is requested by other processes, this
eventually leads to a system deadlock and crash.
Re-order the napi_disable() call to occur after the work function
disabling and urb cancellation calls are issued.
Change-Id: I6ef0b703fc214998a037a68f722f784e1d07815e
Reported-by: http://crbug.com/1017928
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a malicious device gives a short MAC it can elicit up to
5 bytes of leaked memory out of the driver. We need to check for
ETH_ALEN instead.
Reported-by: syzbot+a8d4acdad35e6bbca308@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.
V2: used sizeof as request by Alexander
Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ThinkPad Thunderbolt 3 Dock Gen 2 is another docking station that uses
RTL8153 based USB ethernet.
The device supports macpassthru, but it failed to pass the test of -AD,
-BND and -BD. Simply bypass these tests since the device supports this
feature just fine.
Also the ACPI objects have some differences between Dell's and Lenovo's,
so make those ACPI infos no longer hardcoded.
BugLink: https://bugs.launchpad.net/bugs/1827961
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the pointer rtl_fw->fw would be used before checking in
rtl8152_apply_firmware() that causes the following kernel oops.
Unable to handle kernel NULL pointer dereference at virtual address 00000002
pgd = (ptrval)
[00000002] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 131 Comm: kworker/0:2 Not tainted
5.4.0-rc1-00539-g9370f2d05a2a #6788
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events_long rtl_hw_phy_work_func_t
PC is at rtl8152_apply_firmware+0x14/0x464
LR is at r8153_hw_phy_cfg+0x24/0x17c
pc : [<c064f4e4>] lr : [<c064fa18>] psr: a0000013
sp : e75c9e60 ip : 60000013 fp : c11b7614
r10: e883b91c r9 : 00000000 r8 : fffffffe
r7 : e883b640 r6 : fffffffe r5 : fffffffe r4 : e883b640
r3 : 736cfe7c r2 : 736cfe7c r1 : 000052f8 r0 : e883b640
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 6640006a DAC: 00000051
Process kworker/0:2 (pid: 131, stack limit = 0x(ptrval))
Stack: (0xe75c9e60 to 0xe75ca000)
...
[<c064f4e4>] (rtl8152_apply_firmware) from [<c064fa18>]
(r8153_hw_phy_cfg+0x24/0x17c)
[<c064fa18>] (r8153_hw_phy_cfg) from [<c064e784>]
(rtl_hw_phy_work_func_t+0x220/0x3e4)
[<c064e784>] (rtl_hw_phy_work_func_t) from [<c0148a74>]
(process_one_work+0x22c/0x7c8)
[<c0148a74>] (process_one_work) from [<c0149054>] (worker_thread+0x44/0x520)
[<c0149054>] (worker_thread) from [<c0150548>] (kthread+0x130/0x164)
[<c0150548>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xe75c9fb0 to 0xe75c9ff8)
...
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/lan78xx.c:3995:6: warning:
variable event set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the firmware of PHY NC which is used to fix the issue found
for PHY. Currently, only RTL_VER_04, RTL_VER_05, and RTL_VER_06 need
it.
The order of loading PHY firmware would be
RTL_FW_PHY_START
RTL_FW_PHY_NC
RTL_FW_PHY_STOP
The RTL_FW_PHY_START/RTL_FW_PHY_STOP are used to lock/unlock the PHY,
and set/clear the patch key from the firmware file.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Move r8153_patch_request() forward for later patch.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Make sure @fw_offset field of struct fw_mac is more than the size
of struct fw_mac.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The struct fw_type_1 is used by MAC only, so rename it to a meaningful one.
Besides, adjust two messages. Replace "load xxx fail" with "check xxx fail"
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This device is sold as 'ThinkPad USB-C Dock Gen 2 (40AS)'.
Chipset is RTL8153 and works with r8152.
Without this, the generic cdc_ether grabs the device, and the device jam
connected networks up when the machine suspends.
Signed-off-by: Kazutoshi Noguchi <noguchi.kazutosi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.
Change the order to close this race condition.
Fixes: 92571a1aae ("lan78xx: Connect phy early")
Reported-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.
v2: fix syntax error
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports loading additional firmware file through
request_firmware().
A firmware file may include a header followed by several blocks
which have different types of firmware. Currently, the supported
types are RTL_FW_END, RTL_FW_PLA, and RTL_FW_USB.
The firmware is used to fix some compatible or hardware issues. For
example, the device couldn't be found after rebooting several times.
The supported chips are
RTL_VER_04 (rtl8153a-2.fw)
RTL_VER_05 (rtl8153a-3.fw)
RTL_VER_06 (rtl8153a-4.fw)
RTL_VER_09 (rtl8153b-2.fw)
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure res does not contain random value if the call to
sr_read_cmd fails for some reason.
Reported-by: syzbot+f1842130bbcfb335bac1@syzkaller.appspotmail.com
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MAC address is supplied via device tree or a random
MAC is generated it has to be written to the asix chip in
order to receive any data.
Previously in 9fb137aef3 ("net: usb: ax88179_178a: allow
optionally getting mac address from device tree") this line was
omitted because it seemed to work perfectly fine without it.
But it was simply not detected because the chip keeps the mac
stored even beyond a reset and it was tested on a hardware
with an integrated UPS where the asix chip was permanently
powered on even throughout power cycles.
Fixes: 9fb137aef3 ("net: usb: ax88179_178a: allow optionally getting mac address from device tree")
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 may fail to establish network connection after resume from system
suspend.
If the USB port connects to r8152 lost its power during system suspend,
the MAC address was written before is lost. The reason is that The MAC
address doesn't get written again in its reset_resume callback.
So let's set MAC address again in reset_resume callback. Also remove
unnecessary lock as no other locking attempt will happen during
reset_resume.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch throws warnings for function pointer declarations which lack
identifier names.
An example of such a warning is:
WARNING: function definition argument 'struct r8152 *' should
also have an identifier name
739: FILE: drivers/net/usb/r8152.c:739:
+ void (*init)(struct r8152 *);
So, fix those warnings by adding the identifier names.
While we are at it, also fix a character limit violation which was
causing another checkpatch warning.
Change-Id: Idec857ce2dc9592caf3173188be1660052c052ce
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a guard clause in tx_bottom() to reduce the indentation of the
do-while loop.
Also, fix a couple of spelling and grammatical mistakes in the
r8152_csum_workaround() function comment.
Change-Id: I460befde150ad92248fd85b0f189ec2df2ab8431
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL-pointer dereference on tty open due to a failure to handle a
missing interrupt-in endpoint when probing modem ports:
BUG: kernel NULL pointer dereference, address: 0000000000000006
...
RIP: 0010:tiocmget_submit_urb+0x1c/0xe0 [hso]
...
Call Trace:
hso_start_serial_device+0xdc/0x140 [hso]
hso_serial_open+0x118/0x1b0 [hso]
tty_open+0xf1/0x490
Fixes: 542f548236 ("tty: Modem functions for the HSO driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL-pointer dereference on tty open due to a failure to handle a
missing interrupt-in endpoint when probing modem ports:
BUG: kernel NULL pointer dereference, address: 0000000000000006
...
RIP: 0010:tiocmget_submit_urb+0x1c/0xe0 [hso]
...
Call Trace:
hso_start_serial_device+0xdc/0x140 [hso]
hso_serial_open+0x118/0x1b0 [hso]
tty_open+0xf1/0x490
Fixes: 542f548236 ("tty: Modem functions for the HSO driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt and integrate the feature to pass the MAC address via device tree
from asix_device.c (03fc5d4) also to other ax88179 based asix chips.
E.g. the bootloader fills in local-mac-address and the driver will then
pick up and use this MAC address.
Signed-off-by: Peter Fink <pfink@christ-es.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same for-loop check for the LINK_LIST_READY bit of an OOB_CTRL
register is used in several places. Factor these out into a single
function to reduce the lines of code.
Change-Id: I20e8f327045a72acc0a83e2d145ae2993ab62915
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the drivers more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of these endpoints are used for memory allocations
and as divisors in many usbnet minidrivers. Avoiding zero is therefore
critical.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the driver more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of the out pipe is used as divisor. So this change
fixes a divide-by-zero bug.
Reported-by: syzbot+ce366e2b8296e25d84f5@syzkaller.appspotmail.com
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After a reset packet sizes and device mtu can change and need
to be reevaluated to calculate queue sizes.
Malicious devices can set this to zero and we divide by it.
Introduce sanity checking.
Reported-and-tested-by: syzbot+6102c120be558c885f04@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Mediatek based smartphone owner reports problems with USB
tethering in Linux. The verbose USB listing shows a rndis_host
interface pair (e0/01/03 + 10/00/00), but the driver fails to
bind with
[ 355.960428] usb 1-4: bad CDC descriptors
The problem is a failsafe test intended to filter out ACM serial
functions using the same 02/02/ff class/subclass/protocol as RNDIS.
The serial functions are recognized by their non-zero bmCapabilities.
No RNDIS function with non-zero bmCapabilities were known at the time
this failsafe was added. But it turns out that some Wireless class
RNDIS functions are using the bmCapabilities field. These functions
are uniquely identified as RNDIS by their class/subclass/protocol, so
the failing test can safely be disabled. The same applies to the two
types of Misc class RNDIS functions.
Applying the failsafe to Communication class functions only retains
the original functionality, and fixes the problem for the Mediatek based
smartphone.
Tow examples of CDC functional descriptors with non-zero bmCapabilities
from Wireless class RNDIS functions are:
0e8d:000a Mediatek Crosscall Spider X5 3G Phone
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x0f
connection notifications
sends break
line coding and serial state
get/set/clear comm features
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
and
19d2:1023 ZTE K4201-z
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC Union:
bMasterInterface 0
bSlaveInterface 1
The Mediatek example is believed to apply to most smartphones with
Mediatek firmware. The ZTE example is most likely also part of a larger
family of devices/firmwares.
Suggested-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UPS feature only works for runtime suspend, so UPS flags only
need to be set before enabling runtime suspend. Therefore, I create
a struct to record relative information, and use it before runtime
suspend.
All chips could record such information, even though not all of
them support the feature of UPS. Then, some functions could be
combined.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, for AUTONEG_DISABLE, we only need to modify MII_BMCR.
Second, add advertising parameter for rtl8152_set_speed(). Add
RTL_ADVERTISED_xxx for advertising parameter of rtl8152_set_speed().
Then, the advertising settings from ethtool could be saved.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary use of netif_napi_del. This also avoids to call
napi_disable() after netif_napi_del().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0ee1f47349.
The commit 0ee1f47349 ("r8152: napi hangup fix after
disconnect") adds a check about RTL8152_UNPLUG to determine
if calling napi_disable() is invalid in rtl8152_close(),
when rtl8152_disconnect() is called. This avoids to use
napi_disable() after calling netif_napi_del().
Howver, commit ffa9fec30c ("r8152: set RTL8152_UNPLUG
only for real disconnection") causes that RTL8152_UNPLUG
is not always set when calling rtl8152_disconnect().
Therefore, I have to revert commit 0ee1f47349 ("r8152:
napi hangup fix after disconnect"), first. And submit
another patch to fix it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
