Previously we always had something hooked up to LVDS so we tried very
hard to get a mode. With the Minnowboard this is no longer the case.
If no mode can be found over DDC or the firmware we just ignore LVDS.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
For the minnowboard to work the values found in EMGD are required.
This might break Oaktrail but without hardware to test with I cannot
really tell (and do not really care).
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This turned out to be tricky. Writing to SDVOB on the primary vdc also
writes to SDVOB on the aux vdc, but reading it back on the primary vdc
always fails. Basically we never read from the primary vdc since we
will end up trashing the aux vdc.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Since we can have SDVO on Pipe B we better check the output type instead
of pipe number for Oaktrail HDMI.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
On SDVO pipes (always Pipe B on mrst) we have to sequentially write the
aux vdc. We might be able to skip programming the primary vdc in
some/most places but we don't care about that now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
We start off by adding SDVO limits and converting all limits to the
generic gma_limit_t stuct. Then we separate clock calculations for
LVDS and SDVO. This will be cleaned up later but keep it simple for now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
The present code assumes that optimus is present whenever two
VGA (PCI_CLASS_DISPLAY_VGA) devices are present. This does not
seem to be the case of newer laptops with optimus, in which
case the nvidia gpu is a PCI_CLASS_DISPLAY_3D device.
Rework the logic so that we count both VGA and 3D devices,
when contemplating if optimus is present on the platform.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70208
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Ilia's PMPEG improvements
- MSI fixes, and another attempt at enabling by default
- Initial GK208 support, just modesetting
- "Old" PM code gone, new infrastructure and various different stages of support (depending which chipset / ram type etc) is in its place. This includes support that goes beyond what the previous code was capable of. User control has been deliberately sabotaged, it's not safe to use still.
- Thermal management / fan control that's been present for a while is turned ON by default now.
- Misc other fixes that have accumulated
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (74 commits)
drm/nouveau/fb: implement various bits of work towards memory reclocking
drm/nouveau: implement a simple sysfs interface to new pm code
drm/nouveau/device: initial control object class, with pstate control methods
drm/nouveau/clk: implement power state and engine clock control in core
drm/nouveau/volt: implement voltage control in core
drm/nouveau/bios: parsing for various tables required for power management
drm/nouveau/perfmon: initial infrastructure to expose performance counters
drm/nouveau/bus: add interfaces/helpers for sequencer
drm/nouveau/bus: make external class definitions pointers
drm/nouveau/pwr: initial implementation
drm/nouveau/therm: update target fanspeed outside of therm lock
drm/nouveau/therm: automatic mode by default
drm/nouveau/therm: no toggle fan control either if we can't guarantee no pwm connected
drm/nvc0/therm: allow fan control if we've killed the vbios ppwr ucode
drm/nouveau/therm: if no bios trip/linear info, default to perf-suggested speed
drm/nouveau/therm: add hook for clk to suggest fanspeed to therm
drm/nouveau/pwr: assign a subdev id for upcoming implementation
drm/nouveau/gpio: return different error code for not found vs invalid
drm/nouveau/drm/pm: remove everything except the hwmon interfaces to THERM
drm/nouveau/core: make all info-level messages silent for runtime pm
...
Matches the nv94-nvc0 commit with the same title. Doesn't fix a reported issue,
but NVIDIA use this ordering here too, so let's do it just in case.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch adds a way to define a custom delay when scanning for i2c devices
because the adt7473 sometimes doesn't like the default bitbanging udelay.
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Certain combinations of hardware can't actually support the maximum
detected speed. Add a quirk list that lists pairs of hostbridge/chip pci
ids and the mode that they should work with.
See https://bugs.freedesktop.org/show_bug.cgi?id=20341
Reported-by: Jason Detring <detringj@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
