Commit Graph

267 Commits

Author SHA1 Message Date
Archit Taneja
0d1d3e4465 drm/msm/mdp5: Reset CTL blend registers before configuring them
Assigning LMs dynamically to CRTCs results in REG_MDP5_CTL_LAYER_REGs
and REG_MDP5_CTL_LAYER_EXT_REGs maintaining old values for a LM that
isn't used by our CTL instance anymore.

Clear the ctl's CTL_LAYER_REG and CTL_LAYER_EXT_REGs for all LM
instances. The ones that need to be configured are configured later
in this func.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:36 -04:00
Archit Taneja
8480adacfd drm/msm/mdp5: Assign 'right' mixer to CRTC state
Dynamically assign a right mixer to mdp5_crtc_state in the CRTC's
atomic_check path. Assigning the right mixer has some constraints,
i.e, only a few LMs can be paired together. Update mdp5_mixer_assign
to handle these constraints.

Firstly, we need to identify whether we need a right mixer or not.
At the moment, there are 2 scenarios where a right mixer might be
needed:
- If any of the planes connected to this CRTC is too wide (i.e, is
  comprised of 2 hwpipes).
- If the CRTC's mode itself is too wide (i.e, a 4K mode on HDMI).

We implement both these checks in the mdp5_crtc_atomic_check(), and
pass 'need_right_mixer' to mdp5_setup_pipeline.

If a CRTC is already assigned a single mixer, and a new atomic commit
brings in a drm_plane that needs 2 hwpipes, we can successfully commit
this mode without requiring a full modeset, provided that we still use
the previously assigned mixer as the left mixer. If such an assignment
isn't possible, we'd need to do a full modeset. This scenario has been
ignored for now.

The mixer assignment code is a bit messy, considering we have at most
4 LM instances in hardware. This can probably be re-visited later with
simplified logic.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:36 -04:00
Archit Taneja
359ae86248 drm/msm/mdp5: Stage border out on base stage if CRTC has 2 LMs
If a CRTC comprises of 2 LMs, it is mandatory to enable border out
and assign it to the base stage.

We had to enable border out also when the base plane wasn't fullscreen.
Club these checks and put them in a separate function called
get_start_stage() that returns the starting stage for assigning planes.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:36 -04:00
Archit Taneja
bf8dc0a04e drm/msm/mdp5: Stage right side hwpipes on Right-side Layer Mixer
Now that our mdp5_planes can consist of 2 hwpipes, update the
blend_setup() code to stage the right hwpipe to the left and
right LMs

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:36 -04:00
Archit Taneja
ed78560dc4 drm/msm/mdp5: Prepare Layer Mixers for source split
In order to enable Source Split in HW, we need to add/modify
a few LM register configurations:

- Configure the LM width to be half the mode width, so that
  each LM manages one half of the scanout.
- Tell the 'right' LM that it is configured to be the 'right'
  LM in source split mode.
- Since we now have 2 places where REG_MDP5_LM_BLEND_COLOR_OUT is
  configured, do a read-update-store for the register instead of
  directly writing a value to it.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:36 -04:00
Archit Taneja
c26b4f6cfb drm/msm/mdp5: Configure 'right' hwpipe
Now that we have a right hwpipe in mdp5_plane_state, configure it
mdp5_plane_mode_set(). The only parameters that vary between the
left and right hwpipes are the src_w, src_img_w, src_x and crtc_x
as we just even chop the fb into left and right halves.

Add a mdp5_plane_right_pipe() which will be used by the crtc code
to set up LM stages.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:35 -04:00
Archit Taneja
7a10ee9b57 drm/msm/mdp5: Assign a 'right hwpipe' to plane state
If the drm_plane has a source width that's greater than the max width
supported by a SSPP (2560 pixels on 8x96), then we assign a 'r_hwpipe'
to it in mdp5_plane_atomic_check().

TODO: There are a few scenarios where the hwpipe assignments aren't
recommended by HW. For example, an assignment which results in a
drm_plane to of two different types of hwpipes (say RGB0 on left
and DMA1 on right) is not recommended.
Also, hwpipes have a priority mapping, where the higher priority pipe
needs to be staged on left LM, and the lower priority needs to be
staged on the right LM. For example, the priority order for VIG pipes
in decreasing order of priority is VIG0, VIG1, VIG2, and VIG3. So, VIG0
on left and VIG1 on right is a correct configuration, but VIG1 on left
and VIG0 on right isn't. These scenarios are ignored for now for the
sake of simplicity.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:35 -04:00
Archit Taneja
821be43ff2 drm/msm/mdp5: Create mdp5_hwpipe_mode_set
Refactor mdp5_plane_mode_set to call mdp5_hwpipe_mode_set. The latter
func takes in only the hwpipe and the parameters that need to be
programmed into the hwpipe registers. All the code that calculates these
parameters is left as is in mdp5_plane_mode_set.

In the future, when we let drm_plane be comprised of 2 hwpipes, this func
allow us to configure each pipe without adding redundant code.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:35 -04:00
Archit Taneja
b7621b2a08 drm/msm/mdp5: Add optional 'right' Layer Mixer in CRTC state
Add another mdp5_hw_mixer pointer (r_mixer) in mdp5_crtc_state.
This mixer will be used to generate the right half of the scanout.

With Source Split, a SSPP can now be connected to 2 Layer Mixers, but
has to be at the same blend level (stage #) on both Layer Mixers.

A drm_plane that has a lesser width than the max width supported, will
comprise of a single SSPP/hwpipe, staged on both the Layer Mixers at
the same blend level. A plane that is greater than max width will comprise
of 2 SSPPs, with the 'left' SSPP staged on the left LM, and the 'right'
SSPP staged on the right LM at the same blend level.

For now, the drm_plane consists of only one SSPP, therefore, it
needs to be staged on both the LMs in blend_setup() and mdp5_ctl_blend().
We'll extend this logic to support 2 hwpipes per plane later.

The crtc cursor ops (using the LM cursors, not SSPP cursors) simply
return an error if they're called when the right mixer is assigned to
the CRTC state. With source split is enabled, we're expected to only
SSPP cursors.

This commit adds code that configures the right mixer, but the r_mixer
itself isn't assigned at the moment.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:34 -04:00
Archit Taneja
621da7d93c drm/msm/mdp5: Add a CAP for Source Split
Some of the newer MDP5 versions support Source Split of SSPPs. It is a
feature that allows us to route the output of a hwpipe to 2 Layer
Mixers. This is required to achieve the following use cases:

- Dual DSI: For high res DSI panels (such as 2560x1600 etc), a single
  DSI interface doesn't have the bandwidth to drive the required pixel
  clock. We use 2 DSI interfaces to drive the left and right halves
  of the panel (i.e, 1280x1600 each). The MDP5 pipeline here would look
  like:

         LM0 -- DSPP0 -- INTF1 -- DSI1
        /
hwpipe--
        \
         LM1 -- DSPP1 -- INTF2 -- DSI2

  A single hwpipe is used to scan out the left and right halves to DSI1
  and DSI2 respectively. In order to do this, we need to configure the
  2 Layer Mixers in Source Split mode.

- HDMI 4K: In order to support resolutions with width higher than the
  max width supported by a hwpipe, we club 2 hwpipes together:

hwpipe1 --- LM0 -- DSPP0
       -   -             \
         -                -- 3D Mux -- INTF0 -- HDMI
       -   -             /
hwpipe2 --- LM1 -- DSPP1

  hwpipe1 is staged on the 'left' Layer Mixer, and hwpipe2 is staged on
  the 'right' Layer Mixer. An additional block called the '3D Mux' is
  used to merge the output of the 2 DSPPs to a single interface.
  In this use case, it is possible that a 4K surface is downscaled and
  placed completely within one of the halves. In order to support such
  scenarios (and keep the programming simple), Layer Mixers with Source
  Split can be assigned 2 hw pipes per stage. While scanning out, the HW
  takes care of fetching the pixels fom the correct pipe.

Add a MDP cap to tell whether the HW supports source split or not.
Add a MDP LM cap that tells whether a LM instance can operate in
source split mode (and generate the 'left' part of the display
output).

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:34 -04:00
Archit Taneja
f316b25a23 drm/msm/mdp5: Remove mixer/intf pointers from mdp5_ctl
These are a part of CRTC state, it doesn't feel nice to leave them
hanging in mdp5_ctl struct. Pass mdp5_pipeline pointer instead
wherever it is needed.

We still have some params in mdp5_ctl like start_mask etc which
are derivative of atomic state, and should be rolled back if
a commit fails, but it doesn't seem to cause much trouble.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:34 -04:00
Archit Taneja
0ddc3a6307 drm/msm/mdp5: Start using parameters from CRTC state
In the last few commits, we've been adding params to mdp5_crtc_state, and
assigning them in the atomic_check() funcs. Now it's time to actually
start using them.

Remove the duplicated params from the mdp5_crtc struct, and start using
them in the mdp5_crtc code. The majority of the references to these params
is in code that executes after the atomic swap has occurred, so it's okay
to use crtc->state in them. There are a couple of legacy LM cursor ops that
may not use the updated state, but (I think) it's okay to live with that.

Now that we dynamically allocate a mixer to the CRTC, we can also remove
the static assignment to it in mdp5_crtc_init, and also drop the code that
skipped init-ing WB bound mixers (those will now be rejected by
mdp5_mixer_assign()).

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:34 -04:00
Archit Taneja
bcb877b7fd drm/msm/mdp5: Add more stuff to CRTC state
Things like vblank/err irq masks, mode of operation (command mode or not)
are derivative of the interface and mixer state. Therefore, they need to
be a part of the CRTC state too.

Add them to mdp5_crtc_state, and assign them in the CRTC's atomic_check()
func, so that it can be rolled back to a clean state.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:34 -04:00
Archit Taneja
502e3550c6 drm/msm/mdp5: Assign INTF and CTL in encoder's atomic_check()
The INTF and CTL used in a display pipeline are going to be maintained as
a part of the CRTC state (i.e, in mdp5_crtc_state).

These entities, however, are currently statically assigned to drm_encoders
(i.e. mdp5_encoder). Since these aren't directly visible to the CRTC, we
assign them to the CRTC state in the encoder's atomic_check() op.

With this approach, we assign portions of CRTC state in two different
places: the layer mixer in CRTC's atomic_check(), and the INTF and CTL
pieces in the encoder's atomic_check() op.

We'd have more options here if the drm core maintained encoder state too,
but the current approach of clubbing everything in CRTC's state works just
fine.

Unlike hwpipes and mixers, we don't need to keep a track of INTF/CTL
assignments in the global atomic state. This is because they're currently
not sharable resources. For example, INTF0 and CTL0 will always be assigned
to one drm_encoder. This can change later when we implement writeback and
want a CRTC to use a CTL for a while, and then release it for others to use
it. Or, when a drm_encoder can switch between using a single INTF vs
2 INTFs.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:34 -04:00
Archit Taneja
894558ec8c drm/msm/mdp5: Prepare for dynamic assignment of mixers
Add the stuff needed to allow dynamically assigning a mixer to a CRTC.

Since mixers are a resource that can be shared across multiple CRTCs, we
need to maintain a 'hwmixer_to_crtc' map in the global atomic state,
acquire the mdp5_kms.state_lock modeset lock and so on.

The mixer is assigned in the CRTC's atomic_check() func, a failure will
result in the new state being cleanly rolled back.

The mixer assignment itself is straightforward, and almost identical to
what we do for hwpipes. We don't need to grab the old hwmixer_to_crtc
state like we do in hwpipes since we don't need to compare anything
with the old state at the moment.

The only LM capability we care about at the moment is whether the mixer
instance can be used to display stuff (i.e, connect to an INTF
downstream).

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:34 -04:00
Archit Taneja
c1e2a13090 drm/msm/mdp5: subclass CRTC state
Subclass drm_crtc_state so that we can maintain additional state for
our CRTCs.

Add mdp5_pipeline and mdp5_ctl pointers in the subclassed state.
mdp5_pipeline is a grouping of the HW entities that forms the downstream
pipeline for a particular CRTC. It currently contains pointers to
mdp5_interface and mdp5_hw_mixer tied to this CRTC. Later, we will
have 2 hwmixers in this struct. (We could also have 2 intfs if we want
to support dual DSI with Source Split enabled. Implementing that feature
isn't planned at the moment).

The mdp5_pipeline state isn't used at the moment. For now, we just
introduce mdp5_crtc_state and the crtc funcs needed to manage the
subclassed state.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
eda5dbe55b drm/msm/mdp5: Remove the pipeline stuff in mdp5_ctl
The mdp5_ctl has an 'op_mode' struct which contains info on
the downstream pipeline.

Grouping these params together in a struct doesn't serve much
purpose in the code. Maybe there was a plan to expand this
further that never happened.

Remove the op_mode struct, and place its members directly in
mdp5_ctl. This will help avoid confusion later when I introduce
my own verion of a mdp5 pipeline :)

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
36d1364abb drm/msm/mdp5: Clean up interface assignment
mdp5_interface struct contains data corresponding to a INTF
instance in MDP5 hardware. This sturct is memcpy'd to the
mdp5_encoder struct, and then later to the mdp5_ctl struct.

Instead of copying around interface data, create mdp5_interface
instances in mdp5_init, like how it's done currently done for
pipes and layer mixers. Pass around the interface pointers to
mdp5_encoder and mdp5_ctl. This simplifies the code, and allows
us to decouple encoders from INTFs in the future if needed.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
a2380124fb drm/msm/mdp5: Simplify LM <-> PP mapping
PingPong ID for a Layer Mixer is already contained in
mdp5_hw_mixer.

This avoids the need to retrieve PP ID using macros

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
adfc0e63ab drm/msm/mdp5: Start using mdp5_hw_mixer
Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of
using the LM index.

Like before, the Layer Mixers are assigned statically to the CRTCs.
The hwmixer(s) will later be dynamically assigned to CRTCs.

For now, ignore the hwmixers that can only do WB.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
6803c60630 drm/msm/mdp5: Add structs for hw Layer Mixers
Create a struct to represent MDP5 Layer Mixer instances. This will
eventually allow us to detach CRTCs from the Layer Mixers, and
generally clean things up a bit.

This is very similar to how hwpipes were previously abstracted away
from drm planes.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
384dbd8cda drm/msm/mdp5: describe LM instances in mdp5_cfg
The number of Layer Mixers and the downstream blocks (DSPPs and PPs)
connected to each LM can vary with different MDP5 revisions. These
parameters are also static.

Keep the per instance LM data in mdp5_cfg. This will avoid the need
to have macros which identify PP id or DSPP id the LM is connected
to. We don't configure DSPPs at the moment, but keeping the DSPP
instance # here might come handy later.

Also add a 'caps' field that identifies features supported by a
LM instance. Introduce the caps MDP_LM_CAP_DISPLAY and MDP_LM_CAP_WB
that identify whether a LM instance can be used for display or
writeback.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
01f8a96964 drm/msm/mdp5: Bring back pipe_lock to mdp5_plane struct
We'd previously moved the pipe_lock spinlock to the hwpipe struct. Bring
it back to mdp5_plane. We will need this because an mdp5_plane in the
future could comprise of 2 hw pipes. It makes more sense to have a single
lock to protect the registers for the hw pipes used by a plane, rather
than trying to take individual locks per hwpipe when committing a
configuration.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Archit Taneja
87878d2627 drm/msm/mdp5: Update SSPP_MAX value
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:33 -04:00
Daniel Vetter
02efb35959 drm/msm: Simplify vblank event delivery
The core takes care of handling the send_event vs. close() issues, we
can remove that driver code.

Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-04-08 06:59:32 -04:00
Daniel Vetter
34a2ab5e06 drm: Add acquire ctx parameter to ->update_plane
Just rolling it out, no code change here.

Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170322215058.8671-3-daniel.vetter@ffwll.ch
2017-03-29 09:14:01 +02:00
Daniel Vetter
a45216547e Merge branch 'drm/next/platform' of git://linuxtv.org/pinchartl/media into drm-misc-next
Merge Laurent's drm_platform removal code. Only conflict is with the
drm_pci.h extraction, which allows me to fix up the misplayed
drm_platform_init fumble that 0day and Stephen Rothwell reported.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2017-03-11 11:46:03 +01:00
Noralf Trønnes
81895b5409 drm/msm: Remove drm_debugfs_remove_files() calls
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so it's not necessary to call
drm_debugfs_remove_files(). Additionally it uses
debugfs_remove_recursive() to clean up the debugfs files, so no need
to do that.

Cc: robdclark@gmail.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-10-noralf@tronnes.org
2017-03-01 16:09:52 +01:00
Laurent Pinchart
76adb460fd drm: Remove the struct drm_device platformdev field
The field contains a pointer to the parent platform device of the DRM
device. As struct drm_device also contains a dev pointer to the struct
device embedded in the platform_device structure, the platformdev field
is redundant. Remove it and use the dev pointer directly.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For sti
Acked-by: Russell King <rmk+kernel@armlinux.org.uk> # For armada
Acked-by: Rob Clark <robdclark@gmail.com> # For msm
Acked-by: Xinwei Kong<kong.kongxinwei@hisilicon.com>
2017-02-17 15:27:24 +02:00
Archit Taneja
10967a0687 drm/msm/mdp5: Add support for legacy cursor updates
This code has been more or less picked up from the vc4 and intel
implementations of update_plane() funcs for cursor planes.

The update_plane() func is usually the drm_atomic_helper_update_plane
func that will issue an atomic commit with the plane updates. Such
commits are not intended to be done faster than the vsync rate.

The legacy cursor userspace API, on the other hand, expects the kernel
to handle cursor updates immediately.

Create a fast path in update_plane, which updates the cursor registers
and flushes the configuration. The fast path is taken when there is only
a change in the cursor's position in the crtc, or a change in the
cursor's crop co-ordinates. For anything else, we go via the slow path.

We take the slow path even when the fb changes, and when there is
currently no fb tied to the plane. This should hopefully ensure that we
always take a slow path for every new fb. This in turn should ensure that
the fb is pinned/prepared.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:44 -05:00
Archit Taneja
9142364e46 drm/msm/mdp5: Refactor mdp5_plane_atomic_check
In mdp5_plane_atomic_check, we get crtc_state from drm_plane_state.

Later, for cursor planes, we'll populate the update_plane() func that
takes a fast asynchronous path to implement cursor movements. There, we
would need to call a similar atomic_check func to validate the plane
state, but crtc_state would need to be derived differently.

Refactor mdp5_plane_atomic_check to mdp5_plane_atomic_check_with_state
such that the latter takes crtc_state as an argument.

This is similar to what the intel driver has done for async cursor
updates.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:44 -05:00
Archit Taneja
bff8fba48b drm/msm/mdp5: Add cursor planes
Register cursor drm_planes. The loop in modeset_init that inits the
planes and crtcs has to be refactored a bit. We first iterate all the
hwpipes to find the cursor planes. Then, we loop again to create
crtcs.

In msm_atomic_wait_for_commit_done, remove the check which bypasses
waiting for vsyncs if state->legacy_cursor_updates is true.

We will later create a fast path for cursor position changes in the
cursor plane's update_plane func that doesn't go via the regular
atomic commit path. For rest of cursor related updates, we will have
to wait for vsyncs, so ignore the legacy_cursor_updates flag.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:44 -05:00
Archit Taneja
5798c8e0d3 drm/msm/mdp5: Misc cursor plane bits
These are various changes added in preparation for cursor planes:

- Add a pipe_cursor block for 8x96 in mdp5_cfg.
- Add a new pipe CAP called MDP_PIPE_CAP_CURSOR. Use this to ensure we
  assign a cursor SSPP for a drm_plane with type DRM_PLANE_TYPE_CURSOR.
- Update mdp5_ctl_blend_mask/ext_blend_mask funcs to incorporate cursor
  SSPPs.
- In mdp5_ctl_blend, iterate through MAX_STAGES instead of stage_cnt,
  we need to do this because we can now have empty stages in between.
- In mdp5_crtc_atomic_check, make sure that the cursor plane has the
  highest zorder, and stage the cursor plane to the maximum stage #
  present on the HW.
- Create drm_crtc_funcs that doesn't try to implement cursors using the
  older LM cursor HW.
- Pass drm_plane_type in mdp5_plane_init instead of a bool telling
  whether plane is primary or not.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:44 -05:00
Archit Taneja
829200ac91 drm/msm/mdp5: Configure COLOR3_OUT propagation
In MDP5 Layer Mixer HW, the blender output is only the blended color
components (i.e R, G and B, or COLOR0/1/2 in MDP5 HW terminology). This
is fed to the BG input of the next blender. We also need to provide an
alpha (COLOR3) value for the BG input at the next stage.

This is configured via using the REG_MDP5_LM_BLEND_COLOR_OUT register.
For each stage, we can propagate either the BG or FG alpha to the next
stage.

The approach taken by the driver is to propagate FG alpha, if the plane
staged on that blender has an alpha. If it doesn't, we try to propagate
the base layer's alpha.

This is borrowed from downstream MDP5 kernel driver. Without this, we
don't see any cursor plane content.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:44 -05:00
Archit Taneja
3b6acf1440 drm/msm/mdp5: Use plane helpers to configure src/dst rectangles
The MDP5 plane's atomic_check ops doesn't perform clipping tests.
This didn't hurt us much in the past, but clipping becomes important
with cursor planes.

Use drm_plane_helper_check_state, the way rockchip/intel/mtk drivers
already do. Use these drivers as reference.

Clipping requires knowledge of the crtc width and height. This requires
us to call drm_atomic_helper_check_modeset before
drm_atomic_helper_check_planes in the driver's atomic_check op, because
check_modetest will populate the mode for the crtc, needed to populate
the clip rectangle.

We update the plane_enabled(state) local helper to use state->visible,
since state->visible and 'state->fb && state->crtc' represent the same
thing.

One issue with the existing code is that we don't have a way to disable
the plane when it's completely clipped out. Until there isn't an update
on the crtc (which would de-stage the plane), we would still see the
plane in its last 'visible' configuration.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:44 -05:00
Archit Taneja
106f9727dd drm/msm/mdp5: Prepare CRTC/LM for empty stages
Use SSPP_NONE in mdp5_plane_pipe() if there is now hwpipe allocated for
the drm_plane. Returning '0' means we are returning VIG0 pipe.

Also, use the mdp5_pipe enum to pass around the stage array. Initialize
the stage to SSPP_NONE by default.

We do the above because 1) Cursor plane has to be staged at the topmost
blender of the LM, which can result in empty stages in between 2) In
the future, when we support multiple LMs per CRTC. We could have stages
which don't have any pipe assigned to them.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:44 -05:00
Archit Taneja
e5366ffe50 drm/msm/mdp5: Create only as many CRTCs as we need
We currently create CRTCs equaling to the # of Layer Mixer blocks we
have on the MDP5 HW. This number is generally more than the # of encoders
(INTFs) we have in the MDSS HW. The number of encoders connected to
displays on the platform (as described by DT) would be even lesser.

Create only N drm_crtcs, where N is the number of drm_encoders
successfully registered. To do this, we call modeset_init_intf() before
we init the drm_crtcs and drm_planes.

Because of this change, setting encoder->possible_crtcs needs to be moved
from construct_encoder() to a later point when we know how many CRTCs we
have.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:43 -05:00
Archit Taneja
710a651fdd drm/msm/mdp5: cfg: Change count to unsigned int
Count can't be non-zero. Changing to uint will also prevent future
warnings.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:43 -05:00
Archit Taneja
b3a94705a0 drm/msm/mdp5: Create single encoder per interface (INTF)
For the DSI interfaces, the mdp5_kms core creates 2 encoders for video
and command modes.

Create only a single encoder per interface. When creating the encoder, set
the interface type to MDP5_INTF_MODE_NONE. It's the bridge (DSI/HDMI/eDP)
driver's responsibility to set a different interface type. It can use the
the kms func op set_encoder_mode to change the mode of operation, which
in turn would configure the interface type for the INTF.

In mdp5_cmd_encoder.c, we remove the redundant code, and make the commmand
mode funcs as helpers that are used in mdp5_encoder.c

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:43 -05:00
Archit Taneja
df8a71d2b2 drm/msm/mdp5: Prepare for merging video and command encoders
Rename the mdp5_encoder_* ops for active displays to
mdp5_vid_encoder_* ops.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:43 -05:00
Archit Taneja
9c9f6f8d47 drm/msm: Set encoder's mode of operation using a kms func
The mdp5 kms driver currently sets up multiple encoders per interface
(INTF), one for each kind of mode of operation it supports.
We create 2 drm_encoders for DSI, one for Video Mode and the other
for Command Mode operation. The reason behind this approach could have
been that we aren't aware of the DSI device's mode of operation when
we create the encoders.

This makes things a bit complicated, since these encoders have to
be further attached to the same DSI bridge. The easier way out is
to create a single encoder, and make the DSI driver set its mode
of operation when we know what the DSI device's mode flags are.

Start with providing a way to set the mdp5_intf_mode using a kms
func that sets the encoder's mode of operation. When constructing
a DSI encoder, we set the mode of operation to Video Mode as
default. When the DSI device is attached to the host, we probe the
DSI mode flags and set the corresponding mode of operation.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:43 -05:00
Archit Taneja
97e0011953 drm/msm: Construct only one encoder for DSI
We currently create 2 encoders for DSI interfaces, one for command
mode and other for video mode operation. This isn't needed as we
can't really use both the encoders at the same time. It also makes
connecting bridges harder.

Switch to creating a single encoder. For now, we assume that the
encoder is configured only in video mode. Later, the same encoder
would be usable in both modes.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:43 -05:00
Archit Taneja
f71516bd58 drm/msm/mdp5: Update generated headers
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:42 -05:00
Archit Taneja
d90d7026e7 drm/msm/mdp5: cfg: Add pipe_cursor block
Define the block in advance so that the generated mdp5.xml.h doesn't
break build.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-02-06 11:28:42 -05:00
Dave Airlie
b0df0b251b Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge Linus master to get the connector locking revert.

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: (645 commits)
  sysctl: fix proc_doulongvec_ms_jiffies_minmax()
  Revert "drm/probe-helpers: Drop locking from poll_enable"
  MAINTAINERS: add Dan Streetman to zbud maintainers
  MAINTAINERS: add Dan Streetman to zswap maintainers
  mm: do not export ioremap_page_range symbol for external module
  mn10300: fix build error of missing fpu_save()
  romfs: use different way to generate fsid for BLOCK or MTD
  frv: add missing atomic64 operations
  mm, page_alloc: fix premature OOM when racing with cpuset mems update
  mm, page_alloc: move cpuset seqcount checking to slowpath
  mm, page_alloc: fix fast-path race with cpuset update or removal
  mm, page_alloc: fix check for NULL preferred_zone
  kernel/panic.c: add missing \n
  fbdev: color map copying bounds checking
  frv: add atomic64_add_unless()
  mm/mempolicy.c: do not put mempolicy before using its nodemask
  radix-tree: fix private list warnings
  Documentation/filesystems/proc.txt: add VmPin
  mm, memcg: do not retry precharge charges
  proc: add a schedule point in proc_pid_readdir()
  ...
2017-01-27 11:00:42 +10:00
Rob Clark
c57a94ffd0 drm/msm/mdp5: rip out plane->pending tracking
It would race between userspace thread and commit worker.  Ie. vblank
irq would trigger event and userspace could begin the next atomic
update, before the commit worker had a chance to clear the pending
flag.

If we do end up needing something to prevent userspace from trying
another pageflip before getting vblank event, it should probably be
implemented as a pending_planes bitmask, similar to pending_crtcs.  See
start_atomic() and end_atomic().

Signed-off-by: Rob Clark <robdclark@gmail.com>
2017-01-13 10:21:46 -05:00
Ville Syrjälä
438b74a549 drm: Nuke fb->pixel_format
Replace uses of fb->pixel_format with fb->format->format.
Less duplicated information is a good thing.

Note that coccinelle failed to eliminate the
"/* fourcc format */" comment from drm_framebuffer.h, so I had
to do that part manually.

@@
struct drm_framebuffer *FB;
expression E;
@@
 drm_helper_mode_fill_fb_struct(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *FB;
expression E;
@@
 i9xx_get_initial_plane_config(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *FB;
expression E;
@@
 ironlake_get_initial_plane_config(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *FB;
expression E;
@@
 skylake_get_initial_plane_config(...) {
	...
-	FB->pixel_format = E;
	...
 }

@@
struct drm_framebuffer *a;
struct drm_framebuffer b;
@@
(
- a->pixel_format
+ a->format->format
|
- b.pixel_format
+ b.format->format
)

@@
struct drm_plane_state *a;
struct drm_plane_state b;
@@
(
- a->fb->pixel_format
+ a->fb->format->format
|
- b.fb->pixel_format
+ b.fb->format->format
)

@@
struct drm_crtc *CRTC;
@@
(
- CRTC->primary->fb->pixel_format
+ CRTC->primary->fb->format->format
|
- CRTC->primary->state->fb->pixel_format
+ CRTC->primary->state->fb->format->format
)

@@
struct drm_mode_set *set;
@@
(
- set->fb->pixel_format
+ set->fb->format->format
|
- set->crtc->primary->fb->pixel_format
+ set->crtc->primary->fb->format->format
)

@@
@@
 struct drm_framebuffer {
	 ...
-	 uint32_t pixel_format;
	 ...
 };

v2: Fix commit message (Laurent)
    Rebase due to earlier removal of many fb->pixel_format uses,
    including the 'fb->format = drm_format_info(fb->format->format);'
    snafu
v3: Adjusted the semantic patch a bit and regenerated due to code
    changes

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481751175-18463-1-git-send-email-ville.syrjala@linux.intel.com
2016-12-15 14:55:34 +02:00
Ville Syrjälä
bcb0b46145 drm: Replace drm_format_num_planes() with fb->format->num_planes
Replace drm_format_num_planes(fb->pixel_format) with just
fb->format->num_planes. Avoids the expensive format info lookup.

@@
struct drm_framebuffer *a;
struct drm_framebuffer b;
@@
(
- drm_format_num_planes(a->pixel_format)
+ a->format->num_planes
|
- drm_format_num_planes(b.pixel_format)
+ b.format->num_planes
)

@@
struct drm_plane_state *a;
struct drm_plane_state b;
@@
(
- drm_format_num_planes(a->fb->pixel_format)
+ a->fb->format->num_planes
|
- drm_format_num_planes(b.fb->pixel_format)
+ b.fb->format->num_planes
)

@@
struct drm_framebuffer *a;
identifier T;
@@
  T = a->pixel_format
<+...
- drm_format_num_planes(T)
+ a->format->num_planes
...+>

@@
struct drm_framebuffer b;
identifier T;
@@
  T = b.pixel_format
<+...
- drm_format_num_planes(T)
+ b.format->num_planes
...+>

v2: Rerun spatch due to code changes

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481751022-18015-1-git-send-email-ville.syrjala@linux.intel.com
2016-12-15 14:55:31 +02:00
Dave Airlie
f559013436 Merge branch 'msm-next' of git://people.freedesktop.org/~robclark/linux into drm-next
On the userspace side, all the basics are working, and most of glmark2
is working.  I've been working through deqp, and I've got a couple more
things to fix (but we've gone from 70% to 80+% pass in last day, and
current deqp run that is going should pick up another 5-10%).  I expect
to push the mesa patches today or tomorrow.

There are a couple more a5xx related patches to take the gpu out of
secure mode (for the devices that come up in secure mode, like the hw
I have), but those depend on an scm patch that would come in through
another tree.  If that can land in the next day or two, there might
be a second late pull request for drm/msm.

In addition to the new-shiny, there have also been a lot of overlay/
plane related fixes for issues found using drm-hwc2 (in the process of
testing/debugging the atomic/kms fence patches), resulting in rework
to assign hwpipes to kms planes dynamically (as part of global atomic
state) and also handling SMP (fifo) block allocation atomically as
part of the ->atomic_check() step.  All those patches should also help
out atomic weston (when those patches eventually land).

* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
  drm/msm: gpu: Add support for the GPMU
  drm/msm: gpu: Add A5XX target support
  drm/msm: Disable interrupts during init
  drm/msm: Remove 'src_clk' from adreno configuration
  drm/msm: gpu: Add OUT_TYPE4 and OUT_TYPE7
  drm/msm: Add adreno_gpu_write64()
  drm/msm: gpu Add new gpu register read/write functions
  drm/msm: gpu: Return error on hw_init failure
  drm/msm: gpu: Cut down the list of "generic" registers to the ones we use
  drm/msm: update generated headers
  drm/msm/adreno: move scratch register dumping to per-gen code
  drm/msm/rd: support for 64b iova
  drm/msm: convert iova to 64b
  drm/msm: set dma_mask properly
  drm/msm: Remove bad calls to of_node_put()
  drm/msm/mdp5: move LM bounds check into plane->atomic_check()
  drm/msm/mdp5: dump smp state on errors too
  drm/msm/mdp5: add debugfs to show smp block status
  drm/msm/mdp5: handle SMP block allocations "atomically"
  drm/msm/mdp5: dynamically assign hw pipes to planes
  ...
2016-12-01 09:25:58 +10:00
Dave Airlie
a90f58311f Merge tag 'drm-misc-next-2016-11-29' of git://anongit.freedesktop.org/git/drm-misc into drm-next
Big thing is that drm-misc is now officially a group maintainer/committer
model thing, with MAINTAINERS suitably updated. Otherwise just the usual
pile of misc things all over, nothing that stands out this time around.

* tag 'drm-misc-next-2016-11-29' of git://anongit.freedesktop.org/git/drm-misc: (33 commits)
  drm: Introduce drm_framebuffer_assign()
  drm/bridge: adv7511: Enable the audio data and clock pads on adv7533
  drm/bridge: adv7511: Add Audio support
  drm/edid: Consider alternate cea timings to be the same VIC
  drm/atomic: Constify drm_atomic_crtc_needs_modeset()
  drm: bridge: dw-hdmi: add ASoC dependency
  drm: Fix shift operations for drm_fb_helper::drm_target_preferred()
  drm: Avoid NULL dereference for DRM_LEGACY debug message
  drm: Use u64_to_user_ptr() helper for blob ioctls
  drm: Fix conflicting macro parameter in drm_mm_for_each_node_in_range()
  drm: Fixup kernel doc for driver->gem_create_object
  drm/hisilicon/hibmc: mark PM functions __maybe_unused
  drm/hisilicon/hibmc: Checking for NULL instead of IS_ERR()
  drm: bridge: add DesignWare HDMI I2S audio support
  drm: Check against color expansion in drm_mm_reserve_node()
  drm: Define drm_mm_for_each_node_in_range()
  drm/doc: Fix links in drm_property.c
  MAINTAINERS: Add link to drm-misc documentation
  vgaarb: use valid dev pointer in vgaarb_info()
  drm/atomic: Unconfuse the old_state mess in commmit_tail
  ...
2016-11-30 14:28:20 +10:00