[Why]
When disable driver, OS will set backlight optimization
then do stop device. But this flag will cause driver to
enable ABM when driver disabled.
[How]
Send ABM disable command before destroy ABM construct
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
move the update of otg instance outside of hw programming logic,
since this is sw state, it should always be updated and should
never be optimized away.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The bit for flip addr is being set causing the determination for
FAST vs MEDIUM to always return MEDIUM when plane info is provided
as a surface update. This causes extreme stuttering for the typical
atomic update path on Linux.
[How]
Don't use update_flags->raw for determining FAST vs MEDIUM. It's too
fragile to changes like this.
Explicitly specify the update type per update flag instead. It's not
as clever as checking the bits itself but at least it's correct.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eryk Brol <Eryk.Brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPRX should send the VCP extended colorimetry packet if the
sink supports DPCD rev1.4 and reports the extended colorimetry
bit.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN code should make as few references to DCE as possible
[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. No real HPD plug in/out but HPD happens,
the driver notifies OS connection changed.
2. No display in target.
When HPD goes low to high,
the driver should regard as HPD and enter setmode flow.
[How]
In this case, even stream didn't change but still retrain.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Reuse existent code path and in order to do that apply de gamma
in 1D blender LUT and re use MPC OGAM.
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DPMS state of a display should not impact whether we want to enable fast boot.
Currently fast boot is not enabled when resuming from S4 because of this.
[How]
Remove check for DPMS state when determining if fast boot
can be applied.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many IGT tests require CRC capture in order to confirm that the output
is visually correct.
These skip on dce120 because configure_crc and get_crc aren't set.
[How]
Hook up is_tg_enabled, configure_crc and get_crc functions on dce120's
timing generator.
The logic should be the same as DCE and DCN with some minor register
naming differences.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add these parameters for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support hotspot and memory temperature retrieval on sw smu routine.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support realtime uclk activity report.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Request too frequently may get corrupt data.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support ppfeatures sysfs interface on Vega20 sw smu routine.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smu_get_clk_info_from_vbios() was called repeatedly. It
seems a merge error.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is already sw smu check on IP block adding.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These were only needed for bringup. They're not needed anymore.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
v2: Fix ifdef (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We only want to load DMCU FW on Picasso and Raven 2, not on Raven 1.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Firmware versions can be found as separate sysfs files at:
/sys/class/drm/cardX/device/fw_version (where X is the card number)
The firmware versions are displayed in hexadecimal.
v2: Moved sysfs files to subfolder
Signed-off-by: Ori Messinger <ori.messinger@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It should be attached to VCN 1.0
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since this is VCN specific and only used by VCN
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
it requires to initialize HDP_NONSURFACE_BASE, so as to avoid
using the value left by a previous VM under sriov scenario.
v2: it should not hurt baremetal, generalize it for both sriov
and baremetal
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
only report once per TMO job and the timer would
be restarted upon the job finished if it's just slow.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As far as we know this was never used by userspace and so should be removed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On OD reset, the clock tables in SMU need to be reset to default.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update Vega10 top performance level power state accordingly
on OD.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to enable or disable AVFS if it's already in wanted
state.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With user specified voltage(DPMTABLE_OD_UPDATE_VDDC), the AVFS
will be disabled. However, the buggy code makes this actually not
working as expected.
- V2: clear all OD flags excpet DPMTABLE_OD_UPDATE_VDDC
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This may affects the Vega10 MCLK OD functionality.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To replace checking ring type and make them generic
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no user fence support for VCN
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no user fence support for VCE
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no user fence support for UVD
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So we can generalize the no user fence supported engine
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During S3/S4 bootloader will re-init ras state behind us.
Resume might fail or raise a gpu reset.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During S3/S4 bootloader will re-init ras state behind us.
Resume might fail or raise a gpu reset.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During S3/S4 bootloader will re-init ras state behind us.
Resume might fail or raise a gpu reset.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
suspend/resume will change ras state behind us. Let driver get notified.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add ras suspend function. rename ras_post_init to amdgpu_ras_resume.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add badpages node.
it will output badpages list in format
gpu pfn : gpu page size : flags
example
0x00000000 : 0x00001000 : R
0x00000001 : 0x00001000 : R
0x00000002 : 0x00001000 : R
0x00000003 : 0x00001000 : R
0x00000004 : 0x00001000 : R
0x00000005 : 0x00001000 : R
0x00000006 : 0x00001000 : R
0x00000007 : 0x00001000 : P
0x00000008 : 0x00001000 : P
0x00000009 : 0x00001000 : P
flags can be one of below characters
R: reserved.
P: pending for reserve.
F: failed to reserve for some reasons.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During S3 test, when system wake up and resume, ras interface
is already allocated. Move workaround before ras jumps to resume
step in gfx_v9_0_ecc_late_init, and make sure workaround applied
during resume. Also remove unused mmGB_EDC_MODE clearing.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following sparse warnings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:483:21: warning: symbol 'dce120_clock_source_create' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:506:6: warning: symbol 'dce120_clock_source_destroy' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:513:6: warning: symbol 'dce120_hw_sequencer_create' was not declared. Should it be static?
Fixes: b8fdfcc6a9 ("drm/amd/display: Add DCE12 core support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
