Adding this alias for the Ethernet interface on Jetson TX1 allows the
bootloader to pass the MAC address to the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1 platform because the
supply regulator is not specified for the backlight.
WARNING KERN lp855x 0-002c: 0-002c supply power not found, using dummy regulator
The backlight supply is provided by the 3.3V SYS rail and so add this
as the supply for the backlight.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on the Jetson TX2 platform ...
WARNING KERN tegra-sor 15540000.sor: 15540000.sor supply \
vdd-hdmi-dp-pll not found, using dummy regulator
The problem is caused because the regulator for the SOR device is
missing the '-supply' suffix in Device-Tree. Therefore, add the
'-supply' suffix to fix this warning.
Fixes: 3fdfaf8718 ("arm64: tegra: Enable DP support on Jetson TX2")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1, Jetson Nano and Jetson
TX2 platforms because the supply regulators are not specified for the
EEPROMs.
WARNING KERN at24 0-0050: 0-0050 supply vcc not found, using dummy regulator
WARNING KERN at24 0-0057: 0-0057 supply vcc not found, using dummy regulator
For both of these platforms the EEPROM is powered by the main 1.8V
supply rail and so populate the supply for these devices to fix these
warnings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1
module") populated the EEPROM on the Jetson TX1 module, but did not
enable the corresponding I2C controller. Enable the I2C controller so
that this EEPROM can be accessed.
Fixes: a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1 module")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
clk_out_2 is a clock provided by the PMC, rather than the clock and
reset controller, as previously erroneously defined.
This patch changes clk_out_2 provider to PMC and uses corresponding
PMC clock ID for clk_out_2.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 and Tegra210 PMC blocks have clk_out_1, clk_out_2, clk_out_3,
and a blink clock as a part of the PMC.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
Clock IDs for these clocks are defined in the PMC dt-bindings.
This patch updates the device tree to include the PMC dt-bindings header
and adds the #clock-cells property with one clock specifier to the PMC
node.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to peripheral USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to OTG USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate OTG vbus regulator and add usb-role-switch entry to USB 2-0
port and corresponding connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables XUSB host and pad controller in Tegra194
P2972-0000 board.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
- New architecture features
* Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
* Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure hardware
random number generator. As well as exposing these to userspace, we
also use them as part of the KASLR seed and to seed the crng once
all CPUs have come online.
* Advertise a bunch of new instructions to userspace, including support
for Data Gathering Hint, Matrix Multiply and 16-bit floating point.
- Kexec
* Cleanups in preparation for relocating with the MMU enabled
* Support for loading crash dump kernels with kexec_file_load()
- Perf and PMU drivers
* Cleanups and non-critical fixes for a couple of system PMU drivers
- FPU-less (aka broken) CPU support
* Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck finding
a 64-bit userspace that handles this.
- Modern assembly function annotations
* Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended to
aid debuggers
- Kbuild
* Cleanup detection of LSE support in the assembler by introducing
'as-instr'
* Remove compressed Image files when building clean targets
- IP checksumming
* Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
- Hardware errata
* Work around Cortex-A55 erratum #1530923
- Shadow call stack
* Work around some issues with Clang's integrated assembler not liking
our perfectly reasonable assembly code
* Avoid allocating the X18 register, so that it can be used to hold the
shadow call stack pointer in future
- ACPI
* Fix ID count checking in IORT code. This may regress broken firmware
that happened to work with the old implementation, in which case we'll
have to revert it and try something else
* Fix DAIF corruption on return from GHES handler with pseudo-NMIs
- Miscellaneous
* Whitelist some CPUs that are unaffected by Spectre-v2
* Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
* Reserve a couple of arch-specific PROT flags that are already used by
Sparc and PowerPC and are planned for later use with BTI on arm64
* Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
* Refactoring and cleanup
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl4oY+IQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNNfRB/4p3vax0hqaOnLRvmJPRXF31B8oPlivnr2u
6HCA9LkdU5IlrgaTNOJ/sQEqJAPOPCU7v49Ol0iYw0iKL1suUE7Ikui5VB6Uybqt
YbfF5UNzfXAMs2A86TF/hzqhxw+W+lpnZX8NVTuQeAODfHEGUB1HhTLfRi9INsER
wKEAuoZyuSUibxTFvji+DAq7nVRniXX7CM7tE385pxDisCMuu/7E5wOl+3EZYXWz
DTGzTbHXuVFL+UFCANFEUlAtmr3dQvPFIqAwVl/CxjRJjJ7a+/G3cYLsHFPrQCjj
qYX4kfhAeeBtqmHL7YFNWFwFs5WaT5UcQquFO665/+uCTWSJpORY
=AIh/
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The changes are a real mixed bag this time around.
The only scary looking one from the diffstat is the uapi change to
asm-generic/mman-common.h, but this has been acked by Arnd and is
actually just adding a pair of comments in an attempt to prevent
allocation of some PROT values which tend to get used for
arch-specific purposes. We'll be using them for Branch Target
Identification (a CFI-like hardening feature), which is currently
under review on the mailing list.
New architecture features:
- Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
- Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure
hardware random number generator. As well as exposing these to
userspace, we also use them as part of the KASLR seed and to seed
the crng once all CPUs have come online.
- Advertise a bunch of new instructions to userspace, including
support for Data Gathering Hint, Matrix Multiply and 16-bit
floating point.
Kexec:
- Cleanups in preparation for relocating with the MMU enabled
- Support for loading crash dump kernels with kexec_file_load()
Perf and PMU drivers:
- Cleanups and non-critical fixes for a couple of system PMU drivers
FPU-less (aka broken) CPU support:
- Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck
finding a 64-bit userspace that handles this.
Modern assembly function annotations:
- Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended
to aid debuggers
Kbuild:
- Cleanup detection of LSE support in the assembler by introducing
'as-instr'
- Remove compressed Image files when building clean targets
IP checksumming:
- Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
Hardware errata:
- Work around Cortex-A55 erratum #1530923
Shadow call stack:
- Work around some issues with Clang's integrated assembler not
liking our perfectly reasonable assembly code
- Avoid allocating the X18 register, so that it can be used to hold
the shadow call stack pointer in future
ACPI:
- Fix ID count checking in IORT code. This may regress broken
firmware that happened to work with the old implementation, in
which case we'll have to revert it and try something else
- Fix DAIF corruption on return from GHES handler with pseudo-NMIs
Miscellaneous:
- Whitelist some CPUs that are unaffected by Spectre-v2
- Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
- Reserve a couple of arch-specific PROT flags that are already used
by Sparc and PowerPC and are planned for later use with BTI on
arm64
- Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (73 commits)
arm64: acpi: fix DAIF manipulation with pNMI
arm64: kconfig: Fix alignment of E0PD help text
arm64: Use v8.5-RNG entropy for KASLR seed
arm64: Implement archrandom.h for ARMv8.5-RNG
arm64: kbuild: remove compressed images on 'make ARCH=arm64 (dist)clean'
arm64: entry: Avoid empty alternatives entries
arm64: Kconfig: select HAVE_FUTEX_CMPXCHG
arm64: csum: Fix pathological zero-length calls
arm64: entry: cleanup sp_el0 manipulation
arm64: entry: cleanup el0 svc handler naming
arm64: entry: mark all entry code as notrace
arm64: assembler: remove smp_dmb macro
arm64: assembler: remove inherit_daif macro
ACPI/IORT: Fix 'Number of IDs' handling in iort_id_map()
mm: Reserve asm-generic prot flags 0x10 and 0x20 for arch use
arm64: Use macros instead of hard-coded constants for MAIR_EL1
arm64: Add KRYO{3,4}XX CPU cores to spectre-v2 safe list
arm64: kernel: avoid x18 in __cpu_soft_restart
arm64: kvm: stop treating register x18 as caller save
arm64/lib: copy_page: avoid x18 register in assembler code
...
- Add DMA nodes for am65x and j721e
- Add McASP nodes for am65x and j721e, showcasing the DMA usage
- Add CAL node for am65x
- Add OV5640 camera support for am65x
-----BEGIN PGP SIGNATURE-----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=dL57
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-soc-for-v5.6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC family changes for 5.6, part 2.
- Add DMA nodes for am65x and j721e
- Add McASP nodes for am65x and j721e, showcasing the DMA usage
- Add CAL node for am65x
- Add OV5640 camera support for am65x
* tag 'ti-k3-soc-for-v5.6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
arm64: dts: ti: k3-am65-main Add CAL node
arm64: dts: ti: k3-j721e-main: Add McASP nodes
arm64: dts: ti: k3-am654-main: Add McASP nodes
arm64: dts: ti: k3-j721e: DMA support
arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
arm64: dts: ti: k3-am65: DMA support
arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
Link: https://lore.kernel.org/r/83546942-6215-9c3a-16cd-be7e7c000c0e@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the OV5640 CSI camera:
- add the OV5640 nodes
- add the CAL node linkage
- enable CAL node
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add CAL dtsi node for AM654 device. Including proper power-domains and
clock properties.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the nodes for McASP 0-11 and keep them disabled because several
required properties are not present as they are board specific.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the nodes for McASP 0-2 and keep them disabled because several
required properties are not present as they are board specific.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the ringacc and udmap nodes for main and mcu NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Secure proxy (NAVSS0_SEC_PROXY0) and smmu (NAVSS0_TCU) is part of the
Navigator Subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
NAVSS is a subsystem containing different IPs, it is not really a bus.
Change the compatible from "simple-bus" to "simple-mfd" to reflect that.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
On am654 the MAIN NAVSS base address was 0x30800000, but in j721e it is
at 0x30000000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the ringacc and udmap nodes for main and mcu NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Secure proxy (NAVSS0_SEC_PROXY0) is part of the Navigator Subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
NAVSS is a subsystem containing different IPs, it is not really a bus.
Change the compatible from "simple-bus" to "simple-mfd" to reflect that.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
- Switch from fixed to firmware based clock driver
- Wire power domain driver
- Wire all ina226 chips through IIO and IIO hwmon drivers
- Add missing dr_mode property to usb nodes
- Use gpio-line-names property instead of comments
- Use clock-output-names for si570 differentiation
- Minor DT fixes
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXibMLgAKCRDKSWXLKUoM
IQW6AJ9Szg4yizku9Q6oi+yrR6L3eRxnyACcDiM4EeKIvrlK19cYVnd/58ENPs8=
=k6/g
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-dt-for-v5.6' of https://github.com/Xilinx/linux-xlnx into arm/dt
arm64: dts: zynqmp: DT changes for v5.6
- Switch from fixed to firmware based clock driver
- Wire power domain driver
- Wire all ina226 chips through IIO and IIO hwmon drivers
- Add missing dr_mode property to usb nodes
- Use gpio-line-names property instead of comments
- Use clock-output-names for si570 differentiation
- Minor DT fixes
* tag 'zynqmp-dt-for-v5.6' of https://github.com/Xilinx/linux-xlnx: (21 commits)
arm64: zynqmp: Add label property to all ina226 on zcu106
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu106
arm64: zynqmp: Add label property to all ina226 on zcu102
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu102
arm64: zynqmp: Add label property to all ina226 on zcu111
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu111
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu100
arm64: zynqmp: Setup default number of chipselects for zcu100
arm64: zynqmp: Remove broken-cd from zcu100-revC
arm64: zynqmp: Fix the si570 clock frequency on zcu111
arm64: zynqmp: Setup clock-output-names for si570 chips
arm64: zynqmp: Turn comment to gpio-line-names
arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104
arm64: zynqmp: Remove addition number in node name
arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
arm64: dts: xilinx: Add the power nodes for zynqmp
arm64: dts: xilinx: Remove dtsi for fixed clock
arm64: dts: xilinx: Add the clock nodes for zynqmp
arm64: zynqmp: Add dr_mode property to usb node
arm64: dts: zynqmp: Use decimal values for drm-clock properties
...
Link: https://lore.kernel.org/r/c70d2efa-9ee2-a764-5248-0e5bfbf29f8a@monstr.eu
Signed-off-by: Olof Johansson <olof@lixom.net>
Since v4.3-rc1 commit 0723c05fb7 ("arm64: enable more compressed
Image formats"), it is possible to build Image.{bz2,lz4,lzma,lzo}
AArch64 images. However, the commit missed adding support for removing
those images on 'make ARCH=arm64 (dist)clean'.
Fix this by adding them to the target list.
Make sure to match the order of the recipes in the makefile.
Cc: stable@vger.kernel.org # v4.3+
Fixes: 0723c05fb7 ("arm64: enable more compressed Image formats")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
accross multiple socs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl4k5D4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgfEbCACOCZhDKEttjrJckHExJzyEm+NThYTy4Mmt
FwKS10w3/Fp9Z+Pc7fZk/e1QZ6AlEQPjmy+Ls1r7D7MrkotmPy6YRI6R9OFoj/aw
eUCeo+plJUl2ij8oGgHNnWq6DJEm9cXcmCILuk8K3aj51fWMXH30L0F70lGxAuYb
G1Ta3lnZ22Yc46ie6rQuTU9xtpv2Oy7gtPnZ2uYPEs9T8GFHH/frnaJIyk0SaU4k
n7vWajLqoASDawZJ162+Tq2xtUpNF8CWdYTwtHlheVEC28g9H8f+XX+66x+plrGe
t0Prg62VWUaEn6w80JILxYwPEXh1eHXY7reM/bGwoIW+9U0UtxMX
=8p9R
-----END PGP SIGNATURE-----
Merge tag 'v5.6-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
DSI display for px30 evaluation board and a number of cleanups
accross multiple socs.
* tag 'v5.6-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Kill off "simple-panel" compatibles
arm64: dts: rockchip: rename dwmmc node names to mmc
arm64: dts: rockchip: hook up the px30-evb dsi display
arm64: dts: rockchip: Enable sdio0 and uart0 on rk3399-roc-pc-mezzanine
arm64: dts: rockchip: add reg property to brcmf sub-nodes
arm64: dts: rockchip: fix dwmmc clock name for rk3308
arm64: dts: rockchip: fix dwmmc clock name for px30
Link: https://lore.kernel.org/r/7641353.lIegmeFAIi@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
Current dts files with 'dwmmc' nodes are manually verified.
In order to automate this process rockchip-dw-mshc.txt
has to be converted to yaml. In the new setup
rockchip-dw-mshc.yaml will inherit properties from
mmc-controller.yaml and synopsys-dw-mshc-common.yaml.
'dwmmc' will no longer be a valid name for a node,
so change them all to 'mmc'
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200115185244.18149-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Link: https://lore.kernel.org/r/20200117190305.5257-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Texas Instruments K3 SoC family changes for 5.6
- Add missing power domains for smmu for J721e
- Add I2C, ADC, OSPI and UFS nodes for J721e
- Add OSPI and MCU syscon nodes for am65x
- Add IRQ line for GPIO expander on am65x
* tag 'ti-k3-soc-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-j721e-main: Add missing power-domains for smmu
arm64: dts: ti: k3-am65-mcu: add system control module node
arm64: dts: k3-am654-base-board: Add IRQ line for GPIO expander
arm64: dts: ti: k3-am65: Add OSPI DT node
arm64: dts: ti: k3-j721e: Add DT nodes for few peripherials
Link: https://lore.kernel.org/r/c5b74bfc-f2f0-1b72-4a3c-4c1d478a023a@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The Denali NAND controller IP has separate reset control for the
controller core and registers.
Add the reset-names, and one more phandle accordingly. This is the
approved DT-binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add power-domains entry for smmu, so that the it is accessible as long
as the driver is active. Without this device shutdown is throwing the
below warning:
"[ 44.736348] arm-smmu-v3 36600000.smmu: failed to clear cr0"
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The MCU System control module support is added to the device tree to allow
drivers to access to their System control module registers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add IRQ line for IO expander present on wkup_i2c bus on AM654 EVM
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM654 SoC has two Cadence OSPI controller instances under Flash
subsystem (FSS). Add DT nodes for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
