This also fixes the wrong value for the previously defined
FTM_MODE_INIT macro (it was not used).
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabled the support for the new SoC i.MX8QM by adding the compatible
string of "fsl,imx8qm-ftm-pwm" and its per-compatible data with setting
"has_enable_bits" to "true".
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On the i.MX8x SoC family, an additional PWM enable bit is added for each
PWM channel in the register FTM_SC[23:16]. It supports 8 channels. Bit
16 is for channel 0, and bit 23 is for channel 7. As the IP version
information can not be obtained via any of the FTM registers, a property
of "has_enable_bits" is added via per-compatible data structure.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The current driver assumes that the ftm_sys clock works as one of the
clock sources for the IP block as well as the IP interface clock. This
assumption does not apply any more on the latest i.MX8x SoC family. On
i.MX8x SoCs, a dedicated IP interface clock is introduced and it must be
enabled before accessing any FTM registers. Moreover, the clock can not
be used as the source clock for the FTM IP block. This patch introduces
the ipg_clk as the dedicated IP interface clock and by default it is the
same as the ftm_sys clock if not specified.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
All PWM devices have been marked as "might sleep" since v4.5, there is
no longer a need to differentiate on a per-chip basis.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use flat regmap cache to avoid lockdep warning at probe:
[ 0.697285] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x15c/0x160()
[ 0.697449] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first writes.
However, allocations in an atomic context (e.g. when a spinlock is held)
are not allowed. The function regmap_write calls map->lock, which
acquires a spinlock in the fast_io case. Since the pwm-fsl-ftm driver
uses MMIO, the regmap bus of type regmap_mmio is being used which has
fast_io set to true.
The MMIO space of the pwm-fsl-ftm driver is reasonable condense, hence
using the much faster flat regmap cache is anyway the better choice.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A FTM PWM instance enables/disables three clocks: The bus clock, the
counter clock and the PWM clock. The bus clock gets enabled on
pwm_request, whereas the counter and PWM clocks will be enabled upon
pwm_enable.
The driver has three closesly related issues when enabling/disabling
clocks during suspend/resume:
- The three clocks are not treated differently in regards to the
individual PWM state enabled/requested. This can lead to clocks
getting disabled which have not been enabled in the first place
(a PWM channel which only has been requested going through
suspend/resume).
- When entering suspend, the current behavior relies on the
FTM_OUTMASK register: If a PWM output is unmasked, the driver
assumes the clocks are enabled. However, some PWM instances
have only 2 channels connected (e.g. Vybrid's FTM1). In that case,
the FTM_OUTMASK reads 0x3 if all channels are disabled, even if
the code wrote 0xff to it before. For those PWM instances, the
current approach to detect enabled PWM signals does not work.
- A third issue applies to the bus clock only, which can get enabled
multiple times (once for each PWM channel of a PWM chip). This is
fine, however when entering suspend mode, the clock only gets
disabled once.
This change introduces a different approach by relying on the enable
and prepared counters of the clock framework and using the frameworks
PWM signal states to address all three issues.
Clocks get disabled during suspend and back enabled on resume
regarding to the PWM channels individual state (requested/enabled).
Since we do not count the clock enables in the driver, this change no
longer clears the Status and Control registers Clock Source Selection
(FTM_SC[CLKS]). However, since we disable the selected clock anyway,
and we explicitly select the clock source on reenabling a PWM channel
this approach should not make a difference in practice.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add PM support for FTM PWM driver using callback function suspend
and resume in .driver.pm of platform_driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch is to prepare for adding PM support for FTM PWM driver using
callback function suspend and resume in .driver.pm of platform_driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
No matter how many times the FTM PWM is enabled, the use_count will
always be one.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The regmap core supports different endian modes for devices. This patch
convert to direct regmap API usage, preparing to support big endianness
for LS1 SoC.
Using the regmap framework it will be easy to support devices that only
differ in endianness with the same device driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch intends to prepare for converting to direct regmap API usage.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The implementation of .config(), .enable() and .disable() operations in this
driver may sleep, thus set pwm_chip can_sleep flag.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The FTM PWM device can be found on Vybrid VF610 Tower and
Layerscape LS-1 SoCs.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
