This patch extracts the common part of head32.c and head64.c into head.c.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch reserves the EFI memory map with reserve_early(). Because EFI
memory map is allocated by bootloader, if it is not reserved by
reserved_early(), it may be overwritten through address returned by
find_e820_area().
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes early reserved highmem pages become reserved
pages. This can be used for highmem pages allocated by bootloader such
as EFI memory map, linked list of setup_data, etc.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch clean up reserve_early() family functions by extracting the
common part of reserve_early(), free_early() and bad_addr() into
find_overlapped_early().
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
should use right shift
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this way 32-bit is more similar to 64-bit, and smarter e820 and numa.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when 1/3 user/kernel split is used, and less memory is installed, or if
we have a big hole below 4g, max_low_pfn is still using 3g-128m
try to go down from max_low_pfn until we get it. otherwise will panic.
need to make 32-bit code to use register_e820_active_regions ... later.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
on 64-bit we only get valid max_pfn_mapped after init_memory_mapping().
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
on 32-bit in head_32.S after initial page table is done, we get initial
max_pfn_mapped, and then kernel_physical_mapping_init will give us
a final one.
We need to use that to make sure find_e820_area will get valid addresses
for boot_map and for NODE_DATA(0) on numa32.
XEN PV and lguest may need to assign max_pfn_mapped too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
make mptable to be consistent with acpi routing, so we could:
1. kexec kernel with acpi=off
2. work around BIOSes where acpi routing is working, but mptable is
not right, so can use kernel/kexec to start other OSes that don't have
good acpi support.
command line: update_mptable
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we don't need to call memory_present that early.
numa and sparse will call memory_present later and might
even fail, it will call memory_present for the full range.
also for sparse it will call alloc_bootmem ... before we set up bootmem.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
... otherwise alloc_remap will not get node_mem_map from kva area, and
alloc_node_mem_map has to alloc_bootmem_node to get mem_map.
It will use two low address copies ...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so every element will represent 64M instead of 256M.
AMD opteron could have HW memory hole remapping, so could have
[0, 8g + 64M) on node0. Reduce element size to 64M to keep that on node 0
Later we need to use find_e820_area() to allocate memory_node_map like
on 64-bit. But need to move memory_present out of populate_mem_map...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
on two node system (16g RAM) with numa config I got this crash:
get_memcfg_from_srat: assigning address to rsdp
RSD PTR v0 [ACPIAM]
ACPI: Too big length in RSDT: 92
failed to get NUMA memory information from SRAT table
NUMA - single node, flat memory mode
Node: 0, start_pfn: 0, end_pfn: 153
Setting physnode_map array to node 0 for pfns:
0
...
Pid: 0, comm: swapper Not tainted 2.6.26-rc4 #4
[<80b41289>] hlt_loop+0x0/0x3
[<8011efa0>] ? alloc_remap+0x50/0x70
[<8079e32e>] alloc_node_mem_map+0x5e/0xa0
[<8012e77b>] ? printk+0x1b/0x20
[<80b590f6>] free_area_init_node+0xc6/0x470
[<80b588fc>] ? __alloc_bootmem_node+0x2c/0x50
[<80b58ad8>] ? find_min_pfn_for_node+0x38/0x70
[<8012e77b>] ? printk+0x1b/0x20
[<80b597c4>] free_area_init_nodes+0x254/0x2d0
[<80b544d7>] zone_sizes_init+0x97/0xa0
[<80b48a03>] setup_arch+0x383/0x530
[<8012e77b>] ? printk+0x1b/0x20
[<80b41aa4>] start_kernel+0x64/0x350
[<80b412d8>] i386_start_kernel+0x8/0x10
=======================
this patch increases the acpi table limit to 32.
Also match early_ioremap() with early_iounmap().
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reserve early numa kva, so it will not clash with new RAMDISK
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
introduce init_pg_table_start, so xen PV could specify the value.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove extra -1 in reseve_early calling
panic if can not find space for new RAMDISK
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
UP builds with LOCAL_APIC=y and IO_APIC=n fail with a missing
reference to mp_bus_not_pci. Distangle the mpparse code some more and
move the ioapic specific bus check into a separate function.
This code needs sume urgent un#ifdef surgery all over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
and make e820_mark_nosave_regions to take limit_pfn to use max_low_pfn
for 32bit and end_pfn for 64bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sitsofe Wheeler reported boot problems on linux-next.
It looks like the same issue as found by Soeren Sandman in 7575217f656a93,
"x86: initialize all fields of mp_irqs[mp_irq_entries]".
But his fix is also not complete, as dstapic is used before it assigned.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Bisected-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit "x86: make config_irqsrc not MPspec specific" introduced some uses
of uninitialized fields in mp_config_acpi_legacy_irqs(). I need the
following patch to get sched-devel/master to boot.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
the new output is:
MPTABLE: OEM ID: SUN
MPTABLE: Product ID: 4600 M2
MPTABLE: APIC at: 0x
instead of it all in one line with <6> and double Product ID...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
use find_e820_area to find addess for new RAMDISK, instead of using ram blindly
also print out low ram and bootmap info
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add to the kernels boot memory map 'memmap' entries found in
the EFI memory descriptors passed in from the BIOS.
On EFI systems, up to E820MAX == 128 memory map entries can
be passed via the legacy E820 interface (limited by the size
of the 'zeropage'). These entries can be duplicated in the
EFI descriptors also passed from the BIOS, and possibly more
entries passed by the EFI interface, which does not have the
E820MAX limit on number of memory map entries.
This code doesn't worry about the likely duplicate, overlapping
or (unlikely) conflicting entries between the EFI map and the
E820 map. It just dumps all the EFI entries into the memmap[]
array (which already has the E820 entries) and lets the existing
routine sanitize_e820_map() sort the mess out.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Elaborate on the comment for sanitize_e820_map(), epxlaining more what
it does, what it inputs, and what it returns. Rearrange the placement of
this comment to fit kernel conventions, before the routine's code rather
than buried inside it.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The map size counter passed into, and back out of, sanitize_e820_map(),
was an eight bit type (char or u8), as derived from its origins in
legacy BIOS E820 structures. This patch changes that type to an 'int',
to allow this sanitize routine to also be used on larger maps (larger
than the 256 count that fits in a char). The legacy BIOS E820 interface
of course does not change; that remains at 8 bits for this count, holding
up to E820MAX == 128 entries. But the kernel internals can handle more
when those additional memory map entries are passed from the BIOS via
EFI interfaces.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Extend internal boot time memory tables to allow for up to
three entries per node, which may be larger than the 128 E820MAX
entries handled by the legacy BIOS E820 interface. The EFI
interface, if present, is capable of passing memory map
entries for these larger node counts.
This patch requires an earlier patch that rewrote code depending
on these array sizes from using E820MAX explicitly to size loops,
to instead using ARRAY_SIZE() of the applicable array.
Another patch following this one will provide the code to pick
up additional memory entries passed via the EFI interface from
the BIOS and insert them in the following, now enlarged, arrays.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch is motivated by a subsequent patch which will allow for more
memory map entries on EFI supported systems than can be passed via the x86
legacy BIOS E820 interface. The legacy interface is limited to E820MAX ==
128 memory entries, and that "E820MAX" manifest constant was used as the
size for several arrays and loops over those arrays.
The primary change in this patch is to change code loop sizes over those
arrays from using the constant E820MAX, to using the ARRAY_SIZE() macro
evaluated for the array being looped. That way, a subsequent patch can
change the size of some of these arrays, without breaking this code.
This patch also adds a parameter to the sanitize_e820_map() routine,
which had an implicit size for the array passed it of E820MAX entries.
This new parameter explicitly passes the size of said array. Once again,
this will allow a subsequent patch to change that array size for some
calls to sanitize_e820_map() without breaking the code.
As part of enhancing the sanitize_e820_map() interface this way, I further
combined the unnecessarily distinct x86_32 and x86_64 declarations for
this routine into a single, commonly used, declaration.
This patch in itself should make no difference to the resulting kernel
binary.
[ mingo@elte.hu: merged to -tip ]
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Standardize a few pointer declarations to not have the
extra space after the '*' character.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
