The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supported turning off regulators in suspend only for S2MPS14
device. However this makes also sense for S2MPS11 and can reduce the
power consumption during suspend to RAM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace GPL v2.0+ license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move this enum to rtc-s5m.c once it is meaningless to others drivers [1].
[1] https://marc.info/?l=linux-rtc&m=152060068925948&w=2
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Driver did not provide default value for ramp delay for LDOs which lead
to warning in dmesg, e.g. on Odroid XU4:
[ 1.486076] vdd_ldo9: ramp_delay not set
[ 1.506875] vddq_mmc2: ramp_delay not set
[ 1.523766] vdd_ldo15: ramp_delay not set
[ 1.544702] vdd_sd: ramp_delay not set
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Before updating time and alarm the driver must set appropriate mask in
UDR register. For that purpose the driver uses common register
configuration and a lot of exceptions per device in the code. The
exceptions are not obvious, for example except the change in the logic
sometimes the fields are swapped (WUDR and AUDR between S2MPS14 and
S2MPS15). This leads to quite complicated code.
Try to make it more obvious by:
1. Documenting the UDR masks for devices and operations.
2. Adding fields in register configuration structure for each operation
(read time, write time and alarm).
3. Splitting the configuration per S2MPS13, S2MPS14 and S2MPS15 thus
removing exceptions for them.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
RTC found in s2mps15 is almost same as one found on s2mps13
with few differences in RTC_UPDATE register fields, like:
1> Bit[4] and Bit[1] are reversed
- On s2mps13
WUDR -> bit[4], AUDR -> bit[1]
- On s2mps15
WUDR -> bit[1], AUDR -> bit[4]
2> In case of s2mps13, for alarm register, need to set both
WDUR and ADUR high, whereas for s2mps15 only set AUDR to high.
3> On s2mps15, WUDR, RUDR and AUDR functions should never be used
at the same time.
This patch add required changes to enable s2mps15 rtc timer.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for S2MPS15 PMIC which is similar to S2MPS11 PMIC. The S2MPS15
PMIC supports 27 LDO regulators, 10 buck regulators, RTC, three 32.768KHz
clock outputs and battery charger. This patch adds initial support for
LDO and buck regulators of S2MPS15 device.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[Alim: Added s2mps15_devs like rtc and clk and related changes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The WRSTBI bit (disabled by default but enabled by bootloader), when
set, is responsible for resetting voltages to default values of
certain bucks on falling edge of Warm Reset Input pin from AP.
However on some boards (with S2MPS13) the pin is pulled down so any
suspend will effectively trigger the reset of bucks supplying the power
to the little and big cores. In the same time when resuming, these bucks
must provide voltage greater or equal to voltage before suspend to match
the frequency chosen by cpufreq. If voltage (default value of voltage
after reset) is lower than one set by cpufreq before suspend, then
system will hang during resuming.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.
One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
ACOKB goes high.
On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).
The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS13 RTC is almost the same as S2MPS14. The differences when
updating alarm are:
1. Set WUDR+AUDR field instead of WUDR+RUDR.
2. Clear the AUDR field later (it is not auto-cleared).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC on S2MPS11 is the same as S2MPS14. However interrupt numbers of
RTC alarms 0 and 1 were inversed between these two devices. So when
rtc-s5m driver requested S2MPS14_IRQ_RTCA0 interrupt, it matched to
S2MPS11_IRQ_RTCA1, not RTCA0.
Fix this by using consistent RTC alarm interrupt numbers and adding a
BUILD_BUG_ON for future generations.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) were removed from rtc-s5m driver because they were not used.
Remove them (and on/off interrupt) from main MFD driver and header.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds missing registers('BUCK7_SW' & 'LDO29_CTRL'). Since BUCK7 has
1 more register (BUCK7_SW) than others, register offset should
be added one more for which has bigger address than BUCK7 registers.
Fixes: 76b9840b24ae04(regulator: s2mps11: Add support S2MPS13 regulator device)
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD
driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/
RTC/CLOCK devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a cleanup patch and moves min/step voltages in a common samsung
header file so that they can be used by other s2mpxxx PMIC drivers. Only
few required macros are added currently and others can be added if needed.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Samsung S2MPU02 PMIC device to the MFD sec-core driver.
The S2MPU02 device includes PMIC/RTC/Clock devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Set the time needed for updating alarm and time registers to 0.45 ms.
The default is 7.32 ms which is too long and leads to warnings when
setting alarm or time:
s5m-rtc: waiting for UDR update, reached max number of retries
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for adding support for S2MPS14 RTC device to the rtc-s5m driver:
1. Rename SEC* symbols to S5M.
2. Add S5M prefix to some of defines which are different between S5M876X
and S2MPS14.
This is only a rename-like patch, new code is not added.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The device type was stored in sec_pmic_dev state container twice:
- unsigned long type (initialized from of_device_id or i2c_device_id)
- int device_type (initialized as above or from board files when there
is no DTS)
The 'type' field was never used outside of probe so it can be safely
removed.
Change also the device_type in sec_pmic_dev and sec_platform_data to
unsigned long to avoid any casts.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update the documentation for sec_pmic state container structure to
reflect current code.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The rtc-s5m driver does not support all of S2M and S5M chipsets
supported by main MFD sec-core driver. For such chipsets unsupported by
rtc-s5m, the MFD sec-core driver initialized regmap with default config.
This config in such cases wouldn't work at all.
The main MFD sec-core driver shouldn't initialize regmap for child
drivers which is not used by them and even not valid.
Move the allocation of RTC I2C dummy device and initialization of RTC
regmap from main MFD sec-core driver to the rtc-s5m driver. The rtc-s5m
driver will use proper regmap config for supported devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for external control over GPIO for LDO10, LDO11 and LDO12
S2MPS14 regulators. External control can be turned on by writing 0x0 to
control register which in case of other regulators is used for disabling
them. These LDO10-LDO12 regulators can be disabled only by I2C GPIO or
PWREN pin so the patch actually allows proper way of disabling them.
Additionally the GPIO control has two benefits:
- It is faster than toggling it over I2C bus.
- It allows disabling the regulator during suspend to RAM; The AP will
enable it during resume.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
S2MPS14 regulators support suspend mode where their status is controlled
by PWREN coming from SoC. This patch implements the set_suspend_disable
for S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the necessary entries required for S2MPA01 multi-function
device. While at it also convert whitespaces to tabs in core.h.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When used 64bit compiler GCC warns as
drivers/mfd/sec-core.c:199:10: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for S2MPS14 PMIC device to the MFD sec-core driver.
The S2MPS14 is similar to S2MPS11 but it has fewer regulators, two
clocks instead of three and a little different registers layout.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS11 RTC has two alarms: alarm0 and alarm1 (corresponding
interrupts are named similarly). Use consistent names for interrupts to
limit possible errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add maximum register to the regmap used by rtc-s5m driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for GPIO control (enable/disable) over Buck9. The Buck9
Converter is used as a supply for eMMC Host Controller.
BUCK9EN GPIO of S5M8767 chip may be used by application processor to
enable or disable the Buck9. This has two benefits:
- It is faster than toggling it over I2C bus.
- It allows disabling the regulator during suspend to RAM; The AP will
enable it during resume; Without the patch the regulator supplying
eMMC must be defined as fixed-regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove sec_reg* helpers as they are not used anymore. These helpers were
error-prone as they mixed u8 with unsigned int and they changed order of
some of parameters (val and mask in sec_reg_update()).
Also the helpers didn't give any way of useful abstraction as they just
called corresponding regmap function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=t/v5
-----END PGP SIGNATURE-----
Merge tag 's2mps11-build' into regulator-s5m8767 since a following patch
depend on it.
regulator/clk: Fix s2mps11 build
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
Add symbols for hard-coded values of BUCK_RAMP field in DVS_RAMP
register. This simplifies a little the code as register update is called
only once.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace hard-coded value for mask used in BUCKX_CTRL registers (for
BUCKX_EN field) with a symbol. This also removes two local variables.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving support,
better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=a7dU
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD (multi-function device) updates from Samuel Ortiz:
"For the 3.12 merge window we have one new driver for the DA9063 PMIC
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving
support, better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register
tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes"
* tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (81 commits)
mfd: ucb1x00-core: Rewrite ucb1x00_add_dev()
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for event name
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for sysfs
mfd: timberdale: Use module_pci_driver
mfd: timberdale: Remove redundant break
mfd: timberdale: Staticize local variables
mfd: ab8500-debugfs: Staticize local variables
mfd: db8500-prcmu: Staticize clk_mgt
mfd: db8500-prcmu: Use ANSI function declaration
mfd: omap-usb-host: Staticize usbhs_driver_name
mfd: 88pm805: Fix potential NULL pdata dereference
mfd: 88pm800: Fix potential NULL pdata dereference
mfd: twl6040: Use regmap for register cache
mfd: davinci_voicecodec: Provide a regmap for register I/O
mfd: davinci_voicecodec: Remove unused read and write functions
mmc: memstick: rtsx: Modify copyright comments
mmc: rtsx: Clear SD_CLK toggle enable bit if switching voltage fail
mfd: mmc: rtsx: Change default tx phase
mfd: pcf50633-adc: Use devm_*() functions
mfd: rtsx: Copyright modifications
...
Since these are fixed rate clocks which are registered with common clock
framework so remove these from list of regulators which were unnecessarily
incrementing the count(S2MPS11_REGULATOR_MAX) of regulators.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implementing set_ramp_rate() and using standard constraints for getting
ramp_delay and ramp_disable, instead of getting it as s2mps11 specific data
through platform data, makes driver more compliant with framework and reduces
the complexity for adding DT support.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator subdevice
addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need since
commit 0998d063.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RqMp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For the 3.11 merge we only have one new MFD driver for the Kontron
PLD.
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich
driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator
subdevice addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need
since commit 0998d06310 ("device-core: Ensure drvdata = NULL when
no driver is bound")
* tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (102 commits)
mfd: sec: Provide max_register to regmap
mfd: wm8994: Remove duplicate check for active JACKDET
MAINTAINERS: Add include directory to MFD file patterns
mfd: sec: Remove fields not used since regmap conversion
watchdog: Kontron PLD watchdog timer driver
mfd: max8998: Add support for Device Tree
regulator: max8998: Use arrays for specifying voltages in platform data
mfd: max8998: Add irq domain support
regulator: palmas: Add TPS659038 support
mfd: Kontron PLD mfd driver
mfd: palmas: Add TPS659038 PMIC support
mfd: palmas: Add SMPS10_BOOST feature
mfd: palmas: Check if irq is valid
mfd: lpc_ich: iTCO_wdt patch for Intel Coleto Creek DeviceIDs
mfd: twl-core: Change TWL6025 references to TWL6032
mfd: davinci_voicecodec: Fix build breakage
mfd: vexpress: Make the driver optional for arm and arm64
mfd: htc-egpio: Use devm_ioremap_nocache() instead of ioremap_nocache()
mfd: davinci_voicecodec: Convert to use devm_* APIs
mfd: twl4030-power: Fix relocking on error
...
This patch makes driver to use uV/us as units of ramp_delay. It makes driver
in compliance with regulator framework and make ramp rate precise.
This patch also sets default ramp rate in regulator descriptor which can be
used in case if case ramp rate is not set in regulator constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These were all used by the open coded I/O and IRQ implementations and are
no longer referenced now that the regmap core variants are used instead.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
