The Allwinner A31 that uses this timer has the timer IP asserted in reset.
Add an optional reset property to the DT, and deassert the timer from reset if
it's there.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch set cleans up the Renesas CMT and TMU drivers in preparation for DT
support.
The first 35 patches are a bunch of necessary cleanups that reorganize the CMT
and TMU drivers, their platform data, and the memory, interrupt and clock
resources they expect. As a result the drivers accept a new platform data
model close to the hardware with supports for all the timer channels using a
single device.
The next 13 patches (36/52 to 48/52) move all CMT and TMU platforms from the
old to the new platform data model. Patches 49/52 to 52/52 then drop support
for the old model and perform one more cleanup.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The check for a usable global timer in the probe code does not enquire
which CPU we are currently running on. This can cause the driver to
incorrectly assume we have an unusable global timer if we are running
on a CPU other than A9.
Before checking the CPU revision, ensure we are running on an A9 CPU.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
After hotplugging CPU1 the first call of interrupt handler for CPU1
oneshot timer was called on CPU0 because it fired before setting IRQ
affinity. Affected are SoCs where Multi Core Timer interrupts are
shared (SPI), e.g. Exynos 4210.
During setup of the MCT timers the clock event device should be
registered after setting the affinity for interrupt. This will prevent
starting the timer too early.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143316.299247848@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The starting cpu is not yet in the online mask so irq_set_affinity()
fails which results in per cpu timers for this cpu ending up on some
other online cpu, ususally cpu 0.
Use irq_force_affinity() which disables the online mask check and
makes things work.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143316.106665251@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This helps locating duplicates and inserting new headers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already
includes a copy of the GPL.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
The sh_mtu2 driver gets the MTU2 functional clock using a connection ID
of "mtu2_fck". While all SH SoCs create clock lookup entries with a NULL
device ID and a "mtu2_fck" connection ID, the ARM SoCs use the device ID
only with a NULL connection ID. This works on legacy platforms but will
break on ARM with DT boot.
Fix the situation by using a connection ID of "fck" in the non-legacy
platform data case. Clock lookup entries will be renamed to use the
device ID as well as the connection ID as platforms get moved to new
platform data. The legacy code will eventually be dropped, leaving us
with device ID based clock lookup, compatible with DT boot.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
MTU2 hardware devices can support multiple channels, with global
registers and per-channel registers. The sh_mtu2 driver currently models
the hardware with one Linux device per channel. This model makes it
difficult to handle global registers in a clean way.
Add support for a new model that uses one Linux device per timer with
multiple channels per device. This requires changes to platform data,
add new channel configuration fields.
Support for the legacy model is kept and will be removed after all
platforms switch to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
All boards use clock event ratings of 200 for the MTU2, hardcode it in
the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
The MTU2 is not tied to CPU0, make it usable on any CPU.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Define symbolic macros for all used registers bits.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
This prepares the driver for multi-channel support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
One kzalloc a day keeps the bugs away.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Use the index as the timer start/stop bit and when printing messages to
identify the channel.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
The channel memory base is channel-specific, add it to the channel
structure in preparation for support of multiple channels per device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
The name argument is assigned to const structure fields only, constify
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Move the channel setup code from sh_mtu2_setup to a new
sh_mtu2_setup_channel function and call it from sh_mtu2_setup.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Channel data is private as well, rename priv to device to make the
distrinction between the core device and the channels clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Create a new sh_mtu2_channel structure to hold the channel-specific
fields in preparation for multiple channels per device support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
The rate and periodic fields are used in a single function only, as
local variables. Remove them from the structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
The driver claims it needs to register an interrupt handler too early
for request_irq(). This might have been true in the past, but the only
meaningful difference between request_irq() and setup_irq() today is an
additional kzalloc() call in request_irq(). As the driver calls
kmalloc() itself we know that the slab allocator is available, we can
thus switch to request_irq().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already
includes a copy of the GPL.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The sh_tmu driver gets the TMU functional clock using a connection ID of
"tmu_fck". While all SH SoCs create clock lookup entries with a NULL
device ID and a "tmu_fck" connection ID, the ARM SoCs use the device ID
only with a NULL connection ID. This works on legacy platforms but will
break on ARM with DT boot.
Fix the situation by using a connection ID of "fck" in the non-legacy
platform data case. Clock lookup entries will be renamed to use the
device ID as well as the connection ID as platforms get moved to new
platform data. The legacy code will eventually be dropped, leaving us
with device ID based clock lookup, compatible with DT boot.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
TMU hardware devices can support multiple channels, with global
registers and per-channel registers. The sh_tmu driver currently models
the hardware with one Linux device per channel. This model makes it
difficult to handle global registers in a clean way.
Add support for a new model that uses one Linux device per timer with
multiple channels per device. This requires changes to platform data,
add new channel configuration fields.
Support for the legacy model is kept and will be removed after all
platforms switch to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
All boards use clock event and clock source ratings of 200 for the TMU,
hardcode it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Use the index as the timer start/stop bit and when printing messages to
identify the channel.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The channel memory base is channel-specific, add it to the channel
structure in preparation for support of multiple channels per device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Move the channel setup code from sh_tmu_setup to a new
sh_tmu_setup_channel function and call it from sh_tmu_setup.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Channel data is private as well, rename priv to device to make the
distrinction between the core device and the channels clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Create a new sh_tmu_channel structure to hold the channel-specific
field in preparation for multiple channels per device support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver claims it needs to register an interrupt handler too early
for request_irq(). This might have been true in the past, but the only
meaningful difference between request_irq() and setup_irq() today is an
additional kzalloc() call in request_irq(). As the driver calls
kmalloc() itself we know that the slab allocator is available, we can
thus switch to request_irq().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Clock sources don't need an IRQ, request the IRQ only for channels used
as clock event devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already
includes a copy of the GPL.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The sh_cmt driver gets the CMT functional clock using a connection ID of
"cmt_fck". While all SH SoCs create clock lookup entries with a NULL
device ID and a "cmt_fck" connection ID, the ARM SoCs use the device ID
only with a NULL connection ID. This works on legacy platforms but will
break on ARM with DT boot.
Fix the situation by using a connection ID of "fck" in the non-legacy
platform data case. Clock lookup entries will be renamed to use the
device ID as well as the connection ID as platforms get moved to new
platform data. The legacy code will eventually be dropped, leaving us
with device ID based clock lookup, compatible with DT boot.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
CMT hardware devices can support multiple channels, with global
registers and per-channel registers. The sh_cmt driver currently models
the hardware with one Linux device per channel. This model makes it
difficult to handle global registers in a clean way.
Add support for a new model that uses one Linux device per timer with
multiple channels per device. This requires changes to platform data,
add new channel configuration fields.
Support for the legacy model is kept and will be removed after all
platforms switch to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
All boards use or should use a clock source rating of 125 for the CMT,
hardcode it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
All boards use or should use a clock event rating of 125 for the CMT,
hardcode it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The CMT is a global timer not restricted to a single CPU. It has a lower
rating than the TMU or ARM architected timer, but is still useful on
systems where the other timers are stopped during CPU sleep.
When multiple timers are available the timers core selects which timer
to use based on timer ratings.
On SMP systems where timer broadcasting is required, one dummy timer is
instantiated per CPU with a rating of 100. On those systems the CMT
timer has a rating of 80, which makes the dummy timer selected by
default on all CPUs. The CMT is then available, and will be used as a
broadcast timer.
On UP systems no dummy timer is instantiated. The CMT timer has a rating
of 125 on those systems and is used directly as a clock event device for
CPU0 without broadcasting.
The CMT rating shouldn't depend on whether we boot a UP or SMP system.
We can't raise the CMT rating to 125 on SMP systems. This would select
CMT as the clock event device for CPU0 as its rating is higher than the
dummy timer rating, and would leave the system without a broadcast
timer. We could instead lower the rating to 80 on all systems, but that
wouldn't reflect reality as ratings between 1 and 99 are documented as
"unfit for real use".
We should raise the rating above 99 and still have the CMT selected as a
broadcast timer. This can be done by changing the cpumask from
cpumask_of(0) to cpu_possible_mask. In that case the timer selection
logic will prefer the previously probed and already selected dummy timer
for all CPUs based on the fact that already selected per-cpu timers are
preferred over new global timers, regardless of their respective
ratings. This also better reflects reality, as the CMT is not tied to
the boot CPU.
Ideally the timer selection logic should realize that the CMT needs to
be used as a broadcast timer on SMP systems as no other broadcast timer
is available, regardless of the cpumask and rating.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Create a new sh_cmt_info structure to hold static information about the
device model and reference that structure from the sh_cmt_device
structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The channel memory base is channel-specific, add it to the channel
structure in preparation for support of multiple channels per device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The mapbase variable points to the mapped base address of the channel,
rename it to mapbase_sh. mapbase_str points to the mapped base address
of the CMT device, rename it to mapbase.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Move the channel setup code from sh_cmt_setup to a new
sh_cmt_setup_channel function and call it from sh_cmt_setup.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Channel data is private as well, rename priv to device to make the
distrinction between the core device and the channels clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Create a new sh_cmt_channel structure to hold the channel-specific
field in preparation for multiple channels per device support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver claims it needs to register an interrupt handler too early
for request_irq(). This might have been true in the past, but the only
meaningful difference between request_irq() and setup_irq() today is an
additional kzalloc() call in request_irq(). As the driver calls
kmalloc() itself we know that the slab allocator is available, we can
thus switch to request_irq().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
Pull ARM changes from Russell King:
- Perf updates from Will Deacon:
- Support for Qualcomm Krait processors (run perf on your phone!)
- Support for Cortex-A12 (run perf stat on your FPGA!)
- Support for perf_sample_event_took, allowing us to automatically decrease
the sample rate if we can't handle the PMU interrupts quickly enough
(run perf record on your FPGA!).
- Basic uprobes support from David Long:
This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.
- ARMv7M (microcontroller) updates from Uwe Kleine-König
- OMAP DMA updates (recently added Vinod's Ack even though they've been
sitting in linux-next for a few months) to reduce the reliance of
omap-dma on the code in arch/arm.
- SA11x0 changes from Dmitry Eremin-Solenikov and Alexander Shiyan
- Support for Cortex-A12 CPU
- Align support for ARMv6 with ARMv7 so they can cooperate better in a
single zImage.
- Addition of first AT_HWCAP2 feature bits for ARMv8 crypto support.
- Removal of IRQ_DISABLED from various ARM files
- Improved efficiency of virt_to_page() for single zImage
- Patch from Ulf Hansson to permit runtime PM callbacks to be available for
AMBA devices for suspend/resume as well.
- Finally kill asm/system.h on ARM.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (89 commits)
dmaengine: omap-dma: more consolidation of CCR register setup
dmaengine: omap-dma: move IRQ handling to omap-dma
dmaengine: omap-dma: move register read/writes into omap-dma.c
ARM: omap: dma: get rid of 'p' allocation and clean up
ARM: omap: move dma channel allocation into plat-omap code
ARM: omap: dma: get rid of errata global
ARM: omap: clean up DMA register accesses
ARM: omap: remove almost-const variables
ARM: omap: remove references to disable_irq_lch
dmaengine: omap-dma: cleanup errata 3.3 handling
dmaengine: omap-dma: provide register read/write functions
dmaengine: omap-dma: use cached CCR value when enabling DMA
dmaengine: omap-dma: move barrier to omap_dma_start_desc()
dmaengine: omap-dma: move clnk_ctrl setting to preparation functions
dmaengine: omap-dma: improve efficiency loading C.SA/C.EI/C.FI registers
dmaengine: omap-dma: consolidate clearing channel status register
dmaengine: omap-dma: move CCR buffering disable errata out of the fast path
dmaengine: omap-dma: provide register definitions
dmaengine: omap-dma: consolidate setup of CCR
dmaengine: omap-dma: consolidate setup of CSDP
...
Pull x86 old platform removal from Peter Anvin:
"This patchset removes support for several completely obsolete
platforms, where the maintainers either have completely vanished or
acked the removal. For some of them it is questionable if there even
exists functional specimens of the hardware"
Geert Uytterhoeven apparently thought this was a April Fool's pull request ;)
* 'x86-nuke-platforms-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, platforms: Remove NUMAQ
x86, platforms: Remove SGI Visual Workstation
x86, apic: Remove support for IBM Summit/EXA chipset
x86, apic: Remove support for ia32-based Unisys ES7000
Pull timer changes from Thomas Gleixner:
"This assorted collection provides:
- A new timer based timer broadcast feature for systems which do not
provide a global accessible timer device. That allows those
systems to put CPUs into deep idle states where the per cpu timer
device stops.
- A few NOHZ_FULL related improvements to the timer wheel
- The usual updates to timer devices found in ARM SoCs
- Small improvements and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
tick: Remove code duplication in tick_handle_periodic()
tick: Fix spelling mistake in tick_handle_periodic()
x86: hpet: Use proper destructor for delayed work
workqueue: Provide destroy_delayed_work_on_stack()
clocksource: CMT, MTU2, TMU and STI should depend on GENERIC_CLOCKEVENTS
timer: Remove code redundancy while calling get_nohz_timer_target()
hrtimer: Rearrange comments in the order struct members are declared
timer: Use variable head instead of &work_list in __run_timers()
clocksource: exynos_mct: silence a static checker warning
arm: zynq: Add support for cpufreq
arm: zynq: Don't use arm_global_timer with cpufreq
clocksource/cadence_ttc: Overhaul clocksource frequency adjustment
clocksource/cadence_ttc: Call clockevents_update_freq() with IRQs enabled
clocksource: Add Kconfig entries for CMT, MTU2, TMU and STI
sh: Remove Kconfig entries for TMU, CMT and MTU2
ARM: shmobile: Remove CMT, TMU and STI Kconfig entries
clocksource: armada-370-xp: Use atomic access for shared registers
clocksource: orion: Use atomic access for shared registers
clocksource: timer-keystone: Delete unnecessary variable
clocksource: timer-keystone: introduce clocksource driver for Keystone
...
If GENERIC_CLOCKEVENTS=n:
drivers/clocksource/sh_cmt.c:54:28: error: field 'ced' has incomplete type
drivers/clocksource/sh_cmt.c: In function 'sh_cmt_interrupt':
drivers/clocksource/sh_cmt.c:407:23: error: 'CLOCK_EVT_MODE_ONESHOT' undeclared (first use in this function)
drivers/clocksource/sh_mtu2.c:44:28: error: field 'ced' has incomplete type
drivers/clocksource/sh_mtu2.c: In function 'ced_to_sh_mtu2':
drivers/clocksource/sh_mtu2.c:184:70: warning: initialization from incompatible pointer type [enabled by default]
drivers/clocksource/sh_mtu2.c: At top level:
drivers/clocksource/sh_mtu2.c:188:16: warning: 'enum clock_event_mode' declared inside parameter list [enabled by default]
drivers/clocksource/sh_tmu.c:45:28: error: field 'ced' has incomplete type
drivers/clocksource/sh_tmu.c: In function 'sh_tmu_interrupt':
drivers/clocksource/sh_tmu.c:207:21: error: 'CLOCK_EVT_MODE_ONESHOT' undeclared (first use in this function)
drivers/clocksource/em_sti.c:44:28: error: field 'ced' has incomplete type
drivers/clocksource/em_sti.c: In function 'ced_to_em_sti':
drivers/clocksource/em_sti.c:251:69: warning: initialization from incompatible pointer type [enabled by default]
drivers/clocksource/em_sti.c: At top level:
drivers/clocksource/em_sti.c:255:16: warning: 'enum clock_event_mode' declared inside parameter list [enabled by default]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Magnus Damm <damm@opensource.se>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1395324352-9146-1-git-send-email-geert@linux-m68k.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the clocksource dummy-timer code by using this latter form of callback
registration.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
My guess is we aren't going to have a 2 digit cpuid here any time soon
but the static checkers don't know that and complain that the snprintf()
could overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The currently used method adjusting the clocksource to a changing input
frequency does not work on kernels from 3.11 on.
The new approach is to keep the timer frequency as constant as possible.
I.e.
- due to the TTC's prescaler limitations, allow frequency changes
only if the frequency scales by a power of 2
- adjust the counter's divider on the fly when a frequency change
occurs
This limits cpufreq to scale by certain factors only.
But we may keep the time base somewhat constant, so that sleep() & co
keep working as expected, while supporting cpufreq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The timer core takes care of serialization and IRQs. Hence the driver is
no longer required to disable interrupts when calling
clockevents_update_freq().
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Add Kconfig entries for CMT, MTU2, TMU and STI to
drivers/clocksource/Kconfig. This will allow us to
get rid of duplicated entires in architecture code
such as arch/sh and arch/arm/mach-shmobile.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Replace the driver-specific thread-safe shared register API
by the recently introduced atomic_io_clear_set().
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Replace the driver-specific thread-safe shared register API
by the recently introduced atomic_io_clear_set().
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Commit 438e0bff5257 added the timer-keystone device driver but make use
of an unnecessary variable in the init function. This patch deletes this
variable.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add broadcast clock-event device for the Keystone arch.
The timer can be configured as a general-purpose 64-bit timer,
dual general-purpose 32-bit timers. When configured as dual 32-bit
timers, each half can operate in conjunction (chain mode) or
independently (unchained mode) of each other.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Santosh shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the timer driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Move the U300 timer driver down to the clocksource driver
subsystem and keep arch/arm clean.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Set the CLOCK_EVT_FEAT_DYNIRQ flag on the memory mapped
clockevent so that we save power by waking up the CPU with the
next event when this timer is used in broadcast mode.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Split of the multiplatform support for the Qualcomm SoCs into a mach-qcom
while we leave mach-msm as legacy support. Also, some smp and device tree
related cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
Comment: GPGTools - https://gpgtools.org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=hwTa
-----END PGP SIGNATURE-----
Merge tag 'qcom-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/cleanup
Merge "General cleanups for MSM/QCOM for 3.15" from Kumar Gala:
Split of the multiplatform support for the Qualcomm SoCs into a mach-qcom
while we leave mach-msm as legacy support. Also, some smp and device tree
related cleanups.
* tag 'qcom-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: qcom: Rename various msm prefixed functions to qcom
clocksource: qcom: split building of legacy vs multiplatform support
ARM: qcom: Split Qualcomm support into legacy and multiplatform
clocksource: qcom: Move clocksource code out of mach-msm
ARM: msm: kill off hotplug.c
ARM: msm: Remove pen_release usage
ARM: dts: msm: split out msm8660 and msm8960 soc into dts include
Signed-off-by: Olof Johansson <olof@lixom.net>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
There should no longer be any IBM x440 systems or those using the
Summit/EXA chipset out in the wild, so remove support for it.
We've done our due diligence in reaching out to any contact information
listed for this chipset and no indication was given that it should be
kept around.
Signed-off-by: David Rientjes <rientjes@google.com>
The majority of the clocksource code for the Qualcomm platform is shared
between newer (multiplatform) and older platforms. However there is a bit
of code that isn't, so only build it for the appropriate config.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Since there may be other clocksources available, this driver should not
trigger a panic simply because it can not determine the frequency of an
external clock. This change refactors the driver to allow a warning to
be printed in this case instead.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Cc: Christian Daudt <bcm@fixthebug.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1391559304-26558-1-git-send-email-tim.kryger@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We intend to share the clocksource code for MSM platforms between legacy
and multiplatform supported qcom SoCs.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
When an clock is specified in the device tree, enable it and use it to
determine the external clock frequency.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with some
random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pgLW
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
The 32-bit sched_clock() interface supports 64 bits since
3.13-rc1. Upgrade to the 64-bit function to allow us to remove
the 32-bit registration interface.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1389922686-6249-1-git-send-email-sboyd@codeaurora.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull clocksource/clockevent updates from Daniel Lezcano:
* Axel Lin removed an unused structure defining the ids for the
bcm kona driver.
* Ezequiel Garcia enabled the timer divider only when the 25MHz
timer is not used for the armada 370 XP.
* Jingoo Han removed a pointless platform data initialization for
the sh_mtu and sh_mtu2.
* Laurent Pinchart added the clk_prepare/clk_unprepare for sh_cmt.
* Linus Walleij added a useful warning in clk_of when no clocks
are found while the old behavior was to silently hang at boot time.
* Maxime Ripard added the high speed timer drivers for the
Allwinner SoCs (A10, A13, A20). He increased the rating, shared the
irq across all available cpus and fixed the clockevent's irq
initialization for the sun4i.
* Michael Opdenacker removed the usage of the IRQF_DISABLED for the
all the timers driver located in drivers/clocksource.
* Stephen Boyd switched to sched_clock_register for the
arm_global_timer, cadence_ttc, sun4i and orion timers.
Conflicts:
drivers/clocksource/clksrc-of.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When the kernel is compiled with:
CONFIG_HIGH_RES_TIMERS=no
CONFIG_HZ_PERIODIC=yes
CONFIG_DEBUG_ATOMIC_SLEEP=yes
The following WARN appears:
WARNING: CPU: 1 PID: 0 at linux/kernel/mutex.c:856 mutex_trylock+0x70/0x1fc()
DEBUG_LOCKS_WARN_ON(in_interrupt())
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.12.0-xilinx-dirty #93
[<c0014a78>] (unwind_backtrace+0x0/0x11c) from [<c0011b6c>] (show_stack+0x10/0x14)
[<c0011b6c>] (show_stack+0x10/0x14) from [<c039120c>] (dump_stack+0x7c/0xc0)
[<c039120c>] (dump_stack+0x7c/0xc0) from [<c001fda4>] (warn_slowpath_common+0x60/0x84)
[<c001fda4>] (warn_slowpath_common+0x60/0x84) from [<c001fe48>] (warn_slowpath_fmt+0x2c/0x3c)
[<c001fe48>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0392658>] (mutex_trylock+0x70/0x1fc)
[<c0392658>] (mutex_trylock+0x70/0x1fc) from [<c02dfc08>] (clk_prepare_lock+0xc/0xe4)
[<c02dfc08>] (clk_prepare_lock+0xc/0xe4) from [<c02e099c>] (clk_get_rate+0xc/0x44)
[<c02e099c>] (clk_get_rate+0xc/0x44) from [<c02d0394>] (ttc_set_mode+0x34/0x78)
[<c02d0394>] (ttc_set_mode+0x34/0x78) from [<c005f794>] (clockevents_set_mode+0x28/0x5c)
[<c005f794>] (clockevents_set_mode+0x28/0x5c) from [<c00607fc>] (tick_broadcast_on_off+0x190/0x1c0)
[<c00607fc>] (tick_broadcast_on_off+0x190/0x1c0) from [<c005f168>] (clockevents_notify+0x58/0x1ac)
[<c005f168>] (clockevents_notify+0x58/0x1ac) from [<c02b99dc>] (cpuidle_setup_broadcast_timer+0x20/0x24)
[<c02b99dc>] (cpuidle_setup_broadcast_timer+0x20/0x24) from [<c006cd04>] (generic_smp_call_function_single_interrupt+0)
[<c006cd04>] (generic_smp_call_function_single_interrupt+0xe0/0x130) from [<c00138c8>] (handle_IPI+0x88/0x118)
[<c00138c8>] (handle_IPI+0x88/0x118) from [<c0008504>] (gic_handle_irq+0x58/0x60)
[<c0008504>] (gic_handle_irq+0x58/0x60) from [<c0012644>] (__irq_svc+0x44/0x78)
Exception stack(0xef099fa0 to 0xef099fe8)
9fa0: 00000001 ef092100 00000000 ef092100 ef098000 00000015 c0399f2c c0579d74
9fc0: 0000406a 413fc090 00000000 00000000 00000000 ef099fe8 c00666ec c000f46c
9fe0: 20000113 ffffffff
[<c0012644>] (__irq_svc+0x44/0x78) from [<c000f46c>] (arch_cpu_idle+0x34/0x3c)
[<c000f46c>] (arch_cpu_idle+0x34/0x3c) from [<c0053980>] (cpu_startup_entry+0xa8/0x10c)
[<c0053980>] (cpu_startup_entry+0xa8/0x10c) from [<000085a4>] (0x85a4)
We are in an interrupt context (IPI) and we are calling clk_get_rate in the
set_mode function which in turn ends up by getting a mutex... Even if that
does not hang, it is a potential kernel deadlock.
It is not allowed to call clk_get_rate() from interrupt context. To
avoid such calls the timer input frequency is stored in the driver's
data struct which makes it accessible to the driver in any context.
[dlezcano] completed the changelog with the WARN trace and added a more
detailed description. Tested on zync zc702.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add support Octa Cores for exynos5420
: populate CPU node entries to 8 Cores
: extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
: change status property of dwmmc nodes for exynos5250
: move dwmmc nodes from exynos5 to exynos5250 because
it's different between exynos5250 and exynos5420
: rename mmc nodes from dwmmc for exynos5 SoCs
: add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
: High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
: because the fifo-depth property is SoC specific
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6e6p
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT updates for v3.14
- Add support Octa Cores for exynos5420
: populate CPU node entries to 8 Cores
: extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
: change status property of dwmmc nodes for exynos5250
: move dwmmc nodes from exynos5 to exynos5250 because
it's different between exynos5250 and exynos5420
: rename mmc nodes from dwmmc for exynos5 SoCs
: add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
: High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
: because the fifo-depth property is SoC specific
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Update Samsung sysreg binding document
ARM: dts: Fix sysreg node name in exynos4.dtsi
ARM: dts: Add hs-i2c nodes to exynos5420
ARM: dts: Update min voltage for vdd_arm on Arndale
ARM: dts: populate cpu node entries to 8 cpus for exynos5420
clocksource: mct: extend mct to support 8 local interrupts for Exynos5420
ARM: dts: Add device nodes for GScaler blocks for exynos5420
ARM: dts: Add dwmmc DT nodes for exynos5420 SOC
ARM: dts: rename mmc dts node for exynos5 series
ARM: dts: Move fifo-depth property from exynos5250 board dts
ARM: dts: change status property of dwmmc nodes for exynos5250
ARM: dts: Move dwmmc nodes from exynos5.dtsi to exynos5250.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Since CSR SiRF was converted to multi platform in cf82e0e (ARM: sirf:
enable multiplatform support) the symbol CLOCK_TICK_RATE isn't the
platform specific definition any more, but a global dummy value. There
was no harm introduced in cf82e0e because the global value happens to
match the old platform specific one, still this dummy value isn't
intended to be used and will hopefully disappear soon, so introduce a
local #define and use that instead.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Prepare the clock at probe time, as there is no other appropriate place
in the driver where we're allowed to sleep.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Exynos5420 is octa-core SoC from Samsung. Hence extend exynos-mct clocksource
driver to support 8 local interrupts.
Also extend dts entries for 8 interrupts.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
bcm_timer_ids is no longer used after converting to CLOCKSOURCE_OF_DECLARE.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch removes the use of the IRQF_DISABLED flag.
It's a NOOP since 2.6.35 and it will be removed one day.
[dlezcano] : slightly changed the changelog
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch removes the use of the IRQF_DISABLED flag.
It's a NOOP since 2.6.35 and it will be removed one day.
[dlezcano] : slightly changed the changelog
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch removes the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
[dlezcano] : slightly changed the changelog
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The current code sets the timer divider bits always. However, when
the 25 MHz timer is enabled, this is not needed and has no effect.
As this causes some confusion, rework the code so the divider is
set only when needed, i.e. when the 25 MHz timer is not in use.
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Many platforms rely on clocksource_of_init() being implicitly
called for registering clock sources and will get zero warnings
if no working clock source is available. Let's print a critical
error message if no clock source is found.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface. While we're here, mark the sched_clock function as
notrace to prevent ftrace recursion crashes.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface. While we're here increase the number of bits that
sched_clock can handle to 64 to make full use of the counter.
Cc: Stuart Menefy <stuart.menefy@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Most of the Allwinner SoCs (at this time, all but the A10) also have a
High Speed timers that are not using the 24MHz oscillator as a source
but rather the AHB clock running much faster.
The IP is slightly different between the A10s/A13 and the one used in
the A20/A31, since the latter have 4 timers available, while the former
have only 2 of them.
[dlezcano] : Fixed conflict with b788beda "Order Kconfig options
alphabetically"
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We want to keep this driver as the default provider of the clock events
and source, yet some other driver might fit in the "desired" category of
ratings. Hence, we need to increase a bit the rating so that we can have
more flexibility in the ratings we choose.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The interrupt for the timer is a shared processor interrupt, so any CPU
found in the system can handle it. Switch to our cpumask to
cpu_possible_mask instead of cpumask_of(0).
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
The clock event structure irq field was not filled previously to the
interrupt we're using.
This was resulting in the timer not being used at all when using a
configuration with SMP enabled on a system with several CPUs, and with
the cpumask set to the cpu_possible_mask.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
In commit 620f5e1cbf (dts: Rename DW APB timer compatible strings), both
"snps,dw-apb-timer-sp" and "snps,dw-apb-timer-osc" were deprecated in place
of "snps,dw-apb-timer". But the driver also needs to be udpated in order to
support this new binding "snps,dw-apb-timer".
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The read_sched_clock should return the ~value because the clock is a
countdown implementation. read_sched_clock() should be the same as
__apbt_read_clocksource().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The sun4i timer can still be ticking when we enable the interrupt.
If another timer is actually used (A7 architected timer, for example),
odds are that the interrupt will eventually fire with the event_handler
pointer being NULL.
The obvious fix it to stop the timer before registering the interrupt.
Observed and tested on sun7i (cubietruck).
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When booting a recent kernel on ARM with OF_DYNAMIC enabled, the kernel
warns about the following:
[ 0.000000] ERROR: Bad of_node_put() on /timer@50004600
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.12.0-rc5-next-20131017-00077-gedfd827-dirty #406
[ 0.000000] [<c0015b68>] (unwind_backtrace+0x0/0xf4) from [<c00117e4>] (show_stack+0x10/0x14)
[ 0.000000] [<c00117e4>] (show_stack+0x10/0x14) from [<c055f734>] (dump_stack+0x9c/0xc8)
[ 0.000000] [<c055f734>] (dump_stack+0x9c/0xc8) from [<c03b47d4>] (of_node_release+0x90/0x9c)
[ 0.000000] [<c03b47d4>] (of_node_release+0x90/0x9c) from [<c03b5084>] (of_find_matching_node_and_match+0x78/0xb4)
[ 0.000000] [<c03b5084>] (of_find_matching_node_and_match+0x78/0xb4) from [<c07887c8>] (clocksource_of_init+0x60/0x70)
[ 0.000000] [<c07887c8>] (clocksource_of_init+0x60/0x70) from [<c076e99c>] (start_kernel+0x1f4/0x33c)
[ 0.000000] [<c076e99c>] (start_kernel+0x1f4/0x33c) from [<80008074>] (0x80008074)
This is caused by clocksource_of_init() dropping a reference on the
device node that it never took. The reference taken by the loop is
implicitly dropped on subsequent iterations. See the implementation of
and the comment on top of the of_find_matching_node_and_match()
function for reference (no pun intended).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The time-efm32 driver uses the clocksource MMIO functions.
Thus it needs to select CLKSRC_MMIO in Kconfig.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Both platforms using the MTU (Nomadik and Ux500) have now been
converted to use device tree exclusively, thus let us delete
this platform data header and make this driver a fully
self-contained DT-only driver.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pavel Machek reports that this config is exposed on x86 where the
ARM architected timers aren't even present. Make it depend on the
ARM architected timers being selected so that non-ARM builds
aren't asked about it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Prepare the clock at probe time, as there is no other appropriate place
in the driver where we're allowed to sleep.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix the probe error path to release the clock resource when the
sh_tmu_register() call fails.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Prepare the clock at probe time, as there is no other appropriate place
in the driver where we're allowed to sleep.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix the probe error path to release the clock resource when the
sh_mtu2_register() call fails.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
IRQF_DISABLED is a no-op nowadays, so we can safely remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We need to wait for at least 2 clock cycles whenever we reprogram our
clockevent timer. Report that the minimum number of ticks we can handle
is 3 ticks, and remove 3 ticks to the interval programmed to reflect
this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The Allwinner SoCs timer use the clocksource MMIO functions. We thus
need to select them in Kconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
An efm32 features 4 16-bit timers with a 10-bit prescaler. This driver
provides clocksource and clock event device using one timer instance
each.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add calls to clk_prepare and unprepare so that EMMA Mobile EV2 can
migrate to the common clock framework.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Commit:
65cd4f6 ("arch_timer: Move to generic sched_clock framework")
added code to register the arch_sys_counter in arch_timer_register(),
but it is already registered in arch_counter_register().
This results in the timer being added to the clocksource list twice,
therefore causing an infinite loop in the list.
Remove the duplicate registration and register the scheduler
clock after the original registration instead.
This fixes a hang during boot on Tegra114 (Cortex-A15).
[ While I've only tested this on Tegra114, I suspect the same hang
during boot happens for all processors that use this clock source. ]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1381843911-31962-1-git-send-email-treding@nvidia.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull more timekeeping items for v3.13 from John Stultz:
* Small cleanup in the clocksource code.
* Fix for rtc-pl031 to let it work with alarmtimers.
* Move arm64 to using the generic sched_clock framework & resulting
cleanup in the generic sched_clock code.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Register with the generic sched_clock framework now that it
supports 64 bits. This fixes two problems with the current
sched_clock support for machines using the architected timers.
First off, we don't subtract the start value from subsequent
sched_clock calls so we can potentially start off with
sched_clock returning gigantic numbers. Second, there is no
support for suspend/resume handling so problems such as discussed
in 6a4dae5 (ARM: 7565/1: sched: stop sched_clock() during
suspend, 2012-10-23) can happen without this patch. Finally, it
allows us to move the sched_clock setup into drivers clocksource
out of the arch ports.
Cc: Christopher Covington <cov@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Remove the deprecated IRQF_DISABLED flag.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Check function return values to avoid false positive driver init.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Adds support to configure the rate and enable the event stream for architected
timer. The event streams can be used to impose a timeout on a wfe, to safeguard
against any programming error in case an expected event is not generated or
even to implement wfe-based timeouts for userspace locking implementations.
This feature can be disabled(enabled by default).
Since the timer control register is reset to zero on warm boot, CPU PM notifier
is added to save and restore the value.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Pull (mostly) ARM clocksource driver updates from Daniel Lezcano:
" - Soren Brinkmann added FEAT_PERCPU to a clock device when it is local
per cpu. This feature prevents the clock framework to choose a per cpu
timer as a broadcast timer. This problem arised when the ARM global
timer is used when switching to the broadcast timer which is the case
now on Xillinx with its cpuidle driver.
- Stephen Boyd extended the generic sched_clock code to support 64bit
counters and removes the setup_sched_clock deprecation, as that causes
lots of warnings since there's still users in the arch/arm tree. He
added also the CLOCK_SOURCE_SUSPEND_NONSTOP flag on the architected
timer as they continue counting during suspend.
- Uwe Kleine-König added some missing __init sections and consolidated the
code by moving the of_node_put call from the drivers to the function
clocksource_of_init. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ARM architected timers keep counting during suspend so we can
mark this clocksource with the CLOCK_SOURCE_SUSPEND_NONSTOP flag.
This flag will indicate that this clocksource can be used for
calculating suspend time and injecting sleep time into the
timekeeping core. This should be more accurate than using an
external RTC or architecture specific persistent clock.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
These are all only called by dw_apb_timer_init which is an __init
function, too
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Instead of letting each driver call of_node_put do it centrally in the
loop that also calls the CLOCKSOURCE_OF_DECLARE callbacks. This is less
prone to error and also moves getting and putting the references into the
same function.
Consequently all respective of_node_put calls in drivers are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
The arm_global_timer is a per cpu device. Set the appropriate flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Update to tip/timers/core and resolve minor conflict.
Conflicts:
drivers/clocksource/samsung_pwm_timer.c
Signed-off-by: John Stultz <john.stultz@linaro.org>
Few control settings done in architected timer as part of initialisation
can be lost when CPU enters deeper power states. They need to be
restored when the CPU is (warm)reset again.
This patch adds CPU PM notifiers to save the counter control register
when entering low power modes and restore it when CPU exits low power.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
The ARM architected timer can generate events (used for waking up
CPUs executing the wfe instruction) at a frequency represented as a
power-of-2 divisor of the clock rate.
An event stream might be used:
- To implement wfe-based timeouts for userspace locking implementations.
- To impose a timeout on a wfe for safeguarding against any programming
error in case an expected event is not generated.
This patch computes the event stream frequency aiming for a period
of 100us between events. It uses ARM/ARM64 specific backends to configure
and enable the event stream.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[sudeep: moving ARM/ARM64 changes into separate patches
and adding Kconfig option]
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Update the STI driver by setting cpu_possible_mask to make EMEV2
SMP work as expected together with the ARM broadcast timer.
This breakage was introduced by:
f7db706 ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real hardware clock-event
Without this fix SMP operation is broken on EMEV2 since no
broadcast timer interrupts trigger on the secondary CPU cores.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Clocksource devices provided by DT can be disabled (status != "okay").
Instead of registering clocksource drivers for disabled nodes, respect
the device's status by skiping disabled nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Some variants of Exynos MCT, namely exynos4210-mct at the moment, use
normal, shared interrupts for local timers. This means that each
interrupt must have correct affinity set to fire only on CPU
corresponding to given local timer.
However after recent conversion of clocksource drivers to not use the
local timer API for local timer initialization any more, the point of
time when local timers get initialized changed and irq_set_affinity()
fails because the CPU is not marked as online yet.
This patch fixes this by moving the call to irq_set_affinity() to
CPU_ONLINE notification, so the affinity is being set when the CPU goes
online.
This fixes a regression introduced by commit
ee98d27df6 ARM: EXYNOS4: Divorce mct from local timer API
which rendered all Exynos4210 based boards unbootable due to
failing irq_set_affinity() making local timers inoperatible.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This commit:
573145f08c
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
replaced a call to the driver's timer initialization by a call to
clocksource_of_init(). However, it failed to select CONFIG_CLKSRC_OF.
Fix this by selecting CONFIG_CLKSRC_OF for Armada370/XP machines.
Without this change the kernel is stuck at: 'Calibrating delay loop...'.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Pull timer code update from Thomas Gleixner:
- armada SoC clocksource overhaul with a trivial merge conflict
- Minor improvements to various SoC clocksource drivers
* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
clocksource: armada-370-xp: Get reference fixed-clock by name
clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
clocksource: armada-370-xp: Fix device-tree binding
clocksource: armada-370-xp: Introduce new compatibles
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
clocksource: armada-370-xp: Simplify TIMER_CTRL register access
clocksource: armada-370-xp: Use BIT()
ARM: timer-sp: Set dynamic irq affinity
ARM: nomadik: add dynamic irq flag to the timer
clocksource: sh_cmt: 32-bit control register support
clocksource: em_sti: Convert to devm_* managed helpers
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSLkImAAoJEDqPOy9afJhJOjsP/Ri26AW7XB9pPWJRSU9REBZA
31wxcFo2T+PNir9duwDwjFBFycC3MisaKFlg7D134M+7txbYqm1TRvfu9OEDxpSP
4b/Yl6TarN4dhCN2R+BREO8PnxCBVpspDcsdh6Esuwuet2xUom3UtN8yvSjhPP/u
qGNmXQYXyQy4fom5r+GsDVW+HIhLkaX9b0fYc9EN/bqfgv94PMZAxAxsK9CroAGZ
0m0g9ZXw9iSvVfz+iQEqPINtvpTLHk0FGyimoSR7kvW4o4o47tVtLEWp7VjG6mr5
zvBsycaQq6NgxPu96iUWWhsO9Uj2I7/7JgidXF7r+wvEFs1mcgZtkkirSA/n4zUN
C8a87rvQrZRLr+xXhVuqiVHCgCY8vXoHqkWg6SrZ62ORL8C7uYRpog5SEe2ZzLJX
l5uGAsDM6el+Uc/YviCPoZbeFr3h3CQvvFo8+i2eN0v/Phf30rq4lotBvpQj894G
ngEIMj+D8wshdYSF2dNJ0rLnkLHTgCbiA28L6Cl5TRzRMj3Uaj9aT3cmoLUnimZu
7F7nWU4Iu/vzQKCTQ+eTvwxXJqIlE0JeVbJilqH1f2a68JdXP1LOId+2w/CP8gqQ
i2odj6JHMgBzM9rNs+y0Ir9X/bXIVi6F341c19Nl15srEiLLl8xQIpcPDaI/Kvzs
pefYgF2yS5AZAW3ac90r
=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
When booting with device tree static clkdev aliases should not be used.
This patch modifies the samsung_pwm_timer driver to use DT-based clock
lookup when booting with device tree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
The Armada XP timer has two mandatory clock inputs: nbclk and refclk,
as specified by the device-tree binding.
This commit fixes the clock selection. Instead of hard-coding the clock
rate for the 25 MHz reference fixed-clock, obtain the clock by its name.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
If the clock fails to be obtained and the timer fails to be properly
registered, the kernel will freeze real soon. Instead, let's BUG()
where the actual problem is located.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada XP SoC clocksource driver cannot work without the 25 MHz
fixed timer. Therefore it's appropriate to introduce a new compatible
string and use it to set the 25 MHz fixed timer.
The 'marvell,timer-25MHz' property will be marked as deprecated.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
This is almost cosmetic: we achieve a bit of consistency with
other clocksource drivers by using the CLOCKSOURCE_OF_DECLARE
macro for the boilerplate code.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
This commit creates two functions to access the TIMER_CTRL register:
one for global one for the per-cpu. This makes the code much more
readable. In addition, since the TIMER_CTRL register is also used for
watchdog, this is preparation work for future thread-safe improvements.
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This is a purely cosmetic commit: we replace hardcoded values that
representing bits by BIT(), which is slightly more readable.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Using 0x%# emits 0x0x. Only one is necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the dynamic irq affinity feature to the timer clock device.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Add support for CMT hardware with 32-bit control and counter
registers, as found on r8a73a4 and r8a7790. To use the CMT
with 32-bit hardware a second I/O memory resource needs to
point out the CMSTR register and it needs to be 32 bit wide.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace kzalloc, clk_get, ioremap and request_irq by their managed
counterparts to simplify error paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
* Support for memory mapped arch_timers
* Trivial fixes to the moxart timer code
* Documentation updates
Trivial conflicts in drivers/clocksource/arm_arch_timer.c. Fixed up
the newly added __cpuinit annotations as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
series involve following modifications:
1) fixing up few things in samsung_pwm_timer clocksource driver,
2) moving remaining Samsung platforms to the new clocksource driver,
3) removing old clocksource driver,
4) adding new multiplatform- and DT-aware PWM driver,
5) moving all Samsung platforms to use the new PWM driver,
6) removing old PWM driver,
7) removing all PWM-related code that is not used anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=xmmW
-----END PGP SIGNATURE-----
Merge tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux into next/cleanup
From Tomasz Figa:
Here is the Samsung PWM cleanup series. Particular patches of the series
involve following modifications:
- fixing up few things in samsung_pwm_timer clocksource driver,
- moving remaining Samsung platforms to the new clocksource driver,
- removing old clocksource driver,
- adding new multiplatform- and DT-aware PWM driver,
- moving all Samsung platforms to use the new PWM driver,
- removing old PWM driver,
- removing all PWM-related code that is not used anymore.
* tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux: (684 commits)
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
pwm: samsung: Rename to pwm-samsung-legacy
ARM: SAMSUNG: Remove unused PWM timer IRQ chip code
ARM: SAMSUNG: Remove old samsung-time driver
ARM: SAMSUNG: Move all platforms to new clocksource driver
ARM: SAMSUNG: Set PWM platform data
ARM: SAMSUNG: Add new PWM platform device
ARM: SAMSUNG: Unify base address definitions of timer block
clocksource: samsung_pwm_timer: Handle suspend/resume correctly
clocksource: samsung_pwm_timer: Do not use clocksource_mmio
clocksource: samsung_pwm_timer: Cache clocksource register address
clocksource: samsung_pwm_timer: Correct definition of AUTORELOAD bit
clocksource: samsung_pwm_timer: Do not request PWM mem region
+ v3.11-rc4
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Olof Johansson <olof@lixom.net>
Current suspend/resume handling of the driver was broken, because:
- periodic timer was being enabled in CLOCK_EVT_MODE_RESUME mode, which
does not seem to be correct behavior looking at other platforms,
- PWM divisors need to be restored, but they were not,
- clockevent interrupt mask needs to be restored, but it was not,
- clocksource was being restored in clockevent resume callback.
This patch fixes issues mentioned above, making suspend/resume handling
in the driver correct.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In case of Samsung PWM timer, clocksource MMIO can not be used, because
custom suspend/resume callbacks are required.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Instead of calculating register every time the timer should be read,
we can just do it one time at initialization and store the address in
driver data.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
PWM channel 4 has its autoreload bit located at different position. This
patch fixes the driver to account for that.
This fixes a problem with the clocksource hanging after it overflows because
it is not reloaded any more.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
PWM registers are shared between clocksource and PWM drivers and so can
not be claimed for exclusive use.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Brown <broonie@linaro.org>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add support for the memory mapped timers by filling in the
read/write functions and adding some parsing code. Note that we
only register one clocksource, preferring the cp15 based
clocksource over the mmio one.
To keep things simple we register one global clockevent. This
covers the case of UP and SMP systems with only mmio hardware and
systems where the memory mapped timers are used as the broadcast
timer in low power modes.
The DT binding allows for per-CPU memory mapped timers in case we
want to support that in the future, but the code isn't added
here. We also don't do much for hypervisor support, although it
should be possible to support it by searching for at least two
frames where one frame has the virtual capability and then
updating KVM timers to support it.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
We're going to introduce support to read and write the memory
mapped timer registers in the next patch, so push the cp15
read/write functions one level deeper. This simplifies the next
patch and makes it clearer what's going on.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
There isn't any reason why we don't pass the event here and we'll
need it in the near future for memory mapped arch timers anyway.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Using an enum for the register we wish to access allows newer
compilers to determine if we've forgotten a case in our switch
statement. This allows us to remove the BUILD_BUG() instances in
the arm64 port, avoiding problems where optimizations may not
happen.
To try and force better code generation we're currently marking
the accessor functions as inline, but newer compilers can ignore
the inline keyword unless it's marked __always_inline. Luckily on
arm and arm64 inline is __always_inline, but let's make
everything __always_inline to be explicit.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
bitops.h included implicitly, add #include <linux/bitops.h>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Jingchang Lu <b35083@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface and use all 64 bits of this timer.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
timer API entirely. Doing so will reduce code in ARM core, reduce the
architecture dependencies of our timer drivers, and simplify the code because
we no longer go through an architecture layer that is essentially a hotplug
notifier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABCAAGBQJRydGwAAoJENidgRMleOc9tMMP/Awy0ETkLHQkXdFdRNLQH7Jd
BpDagzBkpt/U/qsh2Dy5Yhz7Qf/HQg6CwJK/b1apHguSPzNcSov+YS7ArPV+kuDY
9OCF5wkVqPW7BPHlxJ+2QAjayIFUaBR+35kpiU+hv9Gkhs11oK90iAWxEIDUGzA6
5miuOVJeyDEwV8des3NYmVVOKziHLJjX3fjMVnc2gxE6PLmOEUQ9t42bVU1aCfub
pRMUXNuG+aFk8lRExPfs4wWfEKCOHrgJPSE4OPFp3pDJeqhFi5tXTiPBQ22FpNf5
78fEDeguS0QS6f/3rGKSdGu/Yz5Lmcldv4tOkfzvNaZP7zhE18wKJu6bSCrZ/Onn
MnhriYWZh+YgX1V8wTMFMPEV+OR+FJdN4C8PhvNWmMC1Xoq25HtrVQUP5aElgAJs
mLcgTXxLYpvZH3jPxdtMR9IuDc+86qmFerGShWqp/1YaNHwpR8dNZxFyVNfw+FUL
/GoAjk/6MsJlZUchiF7I8yp4jYyMcXcV8Bi4tgIAf5rJO9PZBpuxtyAL9uVHnL13
pwkctMnMQwoP6AE9uYfbdnHCKJxF1hny4tKI5sNxAmK8I6bBkfibIZ3sNRAbSrY7
56kV+tJrrgvgAUDkgdluyS9eFs26iHGPsHK4lmzJzFylWmvWFa8tWpP6G0kCa0wP
A1XCqUOryLeL8enPV+z2
=wZbm
-----END PGP SIGNATURE-----
Merge tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds an clocksource driver for the main timer(s)
found on MOXA ART SoCs.
The MOXA ART SoC provides three separate timers with individual
count/load/match registers, two are used here:
TIMER1: clockevents, used to support oneshot and periodic events
TIMER2: set up as a free running counter, used as clocksource
Timers are preconfigured by bootloader to count down and interrupt
on match or zero. Count increments every APB clock cycle and is
automatically reloaded when it reaches zero.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clk-provider.h header is not required by this driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The interval was firing at was set up at probe time, and only changed in
the set_next_event, and never changed back, which is not really what is
expected.
When enabling the periodic mode, now set an interval to tick every
jiffy.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The current bring-up code for the timer was overly complicated. The only
thing we need is actually which clock we want to use as source and
that's pretty much all. Let's keep it that way.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The prescaler is only used when using the internal low frequency
oscillator (at 32kHz). Since we're using the higher frequency oscillator
at 24MHz, we can just remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The set_next_event and set_mode callbacks share a lot of common code we
can easily factor to avoid duplication and mistakes.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The next_event logic was setting the next interval to fire in the
current timer value instead of the interval value register, which is
obviously wrong.
Plus, the logic to set the actual value was wrong as well: the interval
register can only be modified when the timer is disabled, and then
enable it back, otherwise, it'll have no effect. Fix this logic as well
since that code couldn't possibly work.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Even if in our case, this clock was non-gatable, used as a parent clock
for several IPs, it still is a good idea to enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use the second timer found on the Allwinner SoCs as a clock source and
sched clock, that were both not used yet on these platforms.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The name AUTORELOAD was actually pretty bad since it doesn't make the
register reload the previous interval when it expires, but setting this
value pushes the new programmed interval to the internal timer counter.
Rename it to RELOAD instead.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The macros were not using parenthesis to escape the arguments passed to
them. It is pretty unsafe, so add those parenthesis.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The sched_clock.h include is under include/linux now.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the drivers/clocksource and drivers/irqchip uses of
the __cpuinit macros from all C files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
- Infrastructure and DT files for TZ1090 SoC (pin control drivers
already merged via pinctrl tree).
- Panic on boot instead of just warning if cache aliasing possible.
- Various SMP/hotplug fixes.
- Various other randconfig/sparse fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=nmbJ
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull Metag architecture changes from James Hogan:
- Infrastructure and DT files for TZ1090 SoC (pin control drivers
already merged via pinctrl tree).
- Panic on boot instead of just warning if cache aliasing possible.
- Various SMP/hotplug fixes.
- Various other randconfig/sparse fixes.
* tag 'metag-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (24 commits)
metag: move EXPORT_SYMBOL(csum_partial) to metag_ksyms.c
metag: cpu hotplug: route_irq: preserve irq mask
metag: kick: add missing irq_enter/exit to kick_handler()
metag: smp: don't spin waiting for CPU to start
metag: smp: enable irqs after set_cpu_online
metag: use clear_tasks_mm_cpumask()
metag: tz1090: select and instantiate pinctrl-tz1090-pdc
metag: tz1090: select and instantiate pinctrl-tz1090
metag: don't check for cache aliasing on smp cpu boot
metag: panic if cache aliasing possible
metag: *.dts: include using preprocessor
metag: add <dt-bindings/> symlink
metag/.gitignore: Extend the *.dtb pattern to match the dtb.S files
metag/traps: include setup.h for the per_cpu_trap_init declaration
metag/traps: Mark die() as __noreturn to match the declaration.
metag/processor.h: Add missing cpuinfo_op declaration.
metag/setup: Restrict scope for the capabilities variable
metag/mm/cache: Restrict scope for metag_lnkget_probe
metag/asm/irq.h: Declare init_IRQ
metag/kernel/irq.c: Declare root_domain as static
...
Pull ARM updates from Russell King:
"This contains the usual updates from other people (listed below) and
the usual random muddle of miscellaneous ARM updates which cover some
low priority bug fixes and performance improvements.
I've started to put the pull request wording into the merge commits,
which are:
- NoMMU stuff:
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I
were discussing today until we've reached a conclusion/that's had
some more review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now
that you've merged that. I've included the fix for limiting MPU to
CPU_V7.
- Huge page support
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
- LPAE updates
Please pull these miscellaneous LPAE fixes I've been collecting for
a while now for 3.11. They've been tested and reviewed by quite a
few people, and most of the patches are pretty trivial. -- Will Deacon.
- arch_timer cleanups
Please pull these arch_timer cleanups I've been holding onto for a
while. They're the same as my last posting, but have been rebased
to v3.10-rc3.
- mpidr linearisation (multiprocessor id register - identifies which
CPU number we are in the system)
This patch series that implements MPIDR linearization through a
simple hashing algorithm and updates current cpu_{suspend}/{resume}
code to use the newly created hash structures to retrieve context
pointers. It represents a stepping stone for the implementation of
power management code on forthcoming multi-cluster ARM systems.
It has been tested on TC2 (dual cluster A15xA7 system), iMX6q,
OMAP4 and Tegra, with processors hitting low-power states requiring
warm-boot resume through the cpu_resume code path"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: 7775/1: mm: Remove do_sect_fault from LPAE code
ARM: 7777/1: Avoid extra calls to the C compiler
ARM: 7774/1: Fix dtb dependency to use order-only prerequisites
ARM: 7770/1: remove residual ARMv2 support from decompressor
ARM: 7769/1: Cortex-A15: fix erratum 798181 implementation
ARM: 7768/1: prevent risks of out-of-bound access in ASID allocator
ARM: 7767/1: let the ASID allocator handle suspended animation
ARM: 7766/1: versatile: don't mark pen as __INIT
ARM: 7765/1: perf: Record the user-mode PC in the call chain.
ARM: 7735/2: Preserve the user r/w register TPIDRURW on context switch and fork
ARM: kernel: implement stack pointer save array through MPIDR hashing
ARM: kernel: build MPIDR hash function data structure
ARM: mpu: Ensure that MPU depends on CPU_V7
ARM: mpu: protect the vectors page with an MPU region
ARM: mpu: Allow enabling of the MPU via kconfig
ARM: 7758/1: introduce config HAS_BANDGAP
ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting
ARM: 7751/1: zImage: don't overwrite ourself with a page table
ARM: 7749/1: spinlock: retry trylock operation if strex fails on free lock
ARM: 7748/1: oabi: handle faults when loading swi instruction from userspace
...
This is a simple driver for the global timer module found in the Cortex
A9-MP cores from revision r1p0 onwards. This should be able to perform
the functions of the system timer and the local timer in an SMP system.
The global timer has the following features:
The global timer is a 64-bit incrementing counter with an
auto-incrementing feature. It continues incrementing after sending
interrupts. The global timer is memory mapped in the private memory
region.
The global timer is accessible to all Cortex-A9 processors in the
cluster. Each Cortex-A9 processor has a private 64-bit comparator that
is used to assert a private interrupt when the global timer has reached
the comparator value. All the Cortex-A9 processors in a design use the
banked ID, ID27, for this interrupt. ID27 is sent to the Interrupt
Controller as a Private Peripheral Interrupt. The global timer is
clocked by PERIPHCLK.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Rob Herring <robherring2@gmail.com>
CC: Linus Walleij <linus.walleij@linaro.org>
CC: Will Deacon <will.deacon@arm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
These are changes that arrived a little late before the merge
window or that have multiple dependencies on previous branches
so they did not fit into one of the earlier ones. There
are 10 branches merged here, a total of 39 non-merge commits.
Contents are a mixed bag for the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and
the TI 'Nspire' graphing calculator. These should have
been in the 'soc' branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos,
which is based on the other exynos branches to avoid
conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM
Conflicts:
* In Kconfig.debug, various additions trivially conflict,
the list should be kept in alphabetical order when
resolving.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cRu2
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Arnd Bergmann:
"These are changes that arrived a little late before the merge window
or that have multiple dependencies on previous branches so they did
not fit into one of the earlier ones. There are 10 branches merged
here, a total of 39 non-merge commits. Contents are a mixed bag for
the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and the TI
'Nspire' graphing calculator. These should have been in the 'soc'
branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos, which is based
on the other exynos branches to avoid conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: bail out on alien cpus
ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: stih41x: Add B2020 board support
ARM: stih41x: Add B2000 board support
ARM: sti: Add DEBUG_LL console support
ARM: sti: Add STiH416 SOC support
ARM: sti: Add STiH415 SOC support
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
...
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUdLnomCrR//JCVInAQJI/A/9FydsQa9sdnzLFgcdX5BeRRwkXLfDifCM
zDTfUBo+LriKOs7QHblmDg1MnY1UMB2IfrdHD0FsjK7WbZ/91EMAGDPYcI7Fu4+u
pGStxwWi2v+oCT1jjeOkCPT7hdCqogsSpybYq8itSb+zdvdOi6U35dWEKz8xGqz4
vTL9gTZbJP0kowkjIcaryk7FIj7BTIvMCW8n55JZEkDe0BuSJGYn5c3Mntut12ZK
5xM2PeNe2sd3dIdA6XbM2ye/XmYa8xY8Qu4/ijxfH1gnJLvz9Unp96nRXpEbIeMb
BH2Sro8dxsMCaweIQhSRKGnUWMYO/Rh7/+5EqzJ163Ezthx9nvHXJY2ndWuD7uM1
IcGrMxLtqP22TEMtZAVEATDp/5ymxEo5GM+eayUojQDn213wOJjRs5xz5IBsH4KM
8CM/gpadWmLjWku72yEV4lryLcdS0NVQzpTnEbILEGOU4u7qJtxRAp7x7tWBtFg8
4m/eWcSVk/U2SYbXmQHsfukuWgKY0cnZbctPcdnaqXwTP7toJEAK3gxoMtWh49Jq
2M2PVFyFejaaq5b/71wAJ7ePYw56H0N/F3RsGpPE55AY15++gSoQ+3t2Si68hDw8
NtyJMkQYpTvtqJbHXWpQQ3Zfs7pDBe01WDV7i+m4JTNggxUDaO/t1Fqp+fEksm4J
r+luEf5Gcgk=
=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
These changes from 30 individual branches for the most part update device
tree files, but there are also a few source code changes that have crept
in this time, usually in order to atomically move over a driver from
using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once.
There are a few conflicts with the other branches unfortunately:
* in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
from multiple branches. Need to be careful to have the right
set of closing braces as git gets this one wrong.
* In kirkwood.dtsi, one 'ranges' line got split into two lines, while
another line got added. Order of the lines does not matter.
* in sama5d3.dtsi, some cleanup was merged the wrong way, causing
a bogus conflict. We want the 'dmas' and 'dma-names' properties
to get added here.
* Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
* Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8PtJ
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
This patch add a DT enabled driver for timers found on Marvell Orion SoCs
(Kirkwood, Dove, Orion5x, and Discovery Innovation). It installs a free-
running clocksource on timer0 and a clockevent source on timer1.
Corresponding device tree documentation is also added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Separate the armada 370xp local timers from the local timer API.
This will allow us to remove ARM local timer support in the near
future and makes this driver multi-architecture friendly.
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clocksource/time-armada-370-xp.c:217:13: warning: symbol
'armada_370_xp_timer_init' was not declared. Should it be static?
Also remove the __init marking in the prototype as it's
unnecessary and drop the init.h file.
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Separate the marco local timers from the local timer API. This
will allow us to remove ARM local timer support in the near future
and gets us closer to moving this driver to drivers/clocksource.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Barry Song <baohua.song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Separate the mct local timers from the local timer API. This will
allow us to remove ARM local timer support in the near future and
gets us closer to moving this driver to drivers/clocksource.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Several architectures have a dummy timer driver tightly coupled with
their broadcast code to support machines without cpu-local timers (or
where there is a lack of driver support).
Since 12ad100046: "clockevents: Add generic timer broadcast function"
it's been possible to write broadcast-capable timer drivers decoupled
from the broadcast mechanism. We can use this functionality to implement
a generic dummy timer driver that can be shared by all architectures
with generic tick broadcast (ARCH_HAS_TICK_BROADCAST).
This patch implements a generic dummy timer using this facility.
[sboyd: Make percpu data static, use __this_cpu_ptr(), move to
early_initcall to properly register on each CPU, only
register if more than one CPU possible]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>,
Cc: John Stultz <john.stultz@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1370291642-13259-3-git-send-email-sboyd@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABCAAGBQJRw/9tAAoJEPOmecmc0R2B3NMH/A609NR5Yag2vftml8Gl+Iya
2k/dligAPxx/WEogXwxrCcEwFvxA3iNvD9M7MuXZ25ffFL6SgYLnxNYCU53rXRmE
UBQP3OTW/5FyR3N/JGCLW4G8f6LoNWGtOaZqpMC97J4ucnWV/DtbEpoO7qlET/p0
zUsqIpFc9RGroRAmDuRRKpOuArBX5N9utH4fvpZ1XiXztIaESdCiGDFx4AN5g7Iq
uujcKK1NOoj4X/LXj0j4A1ECAhpJ5W8exacdwZZnKVVwA1CpEFxQLu9ekvCYYMNC
6LWhp2/ptgRj7Tv5uVqbHJn4jKd/OM+X0Rn6HcMY1Dwhf37Oa2wPEuQ2qMzcE6A=
=4BBI
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rockchip-basics' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/soc
From Heiko Stuebner:
Adds basic support for Rockchip Cortex-A9 SoCs.
* tag 'v3.11-rockchip-basics' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
clocksource: dw_apb_timer_of: use clocksource_of_init
clocksource: dw_apb_timer_of: select DW_APB_TIMER
clocksource: dw_apb_timer_of: add clock-handling
clocksource: dw_apb_timer_of: enable the use the clocksource as sched clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlG+ysgACgkQykllyylKDCENewCgk3LUwpMxepV1JOaNBmUJ0A09
jtMAnA395sve+FBxYjfM+nSAmbnl5RYl
=KBrZ
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx into next/dt
From Michal Simek:
arm: Xilinx Zynq dt changes for v3.11
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
* tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx:
arm: dt: zynq: Add support for the zed platform
arm: dt: zynq: Add support for the zc706 platform
arm: dt: zynq: Use 'status' property for UART nodes
arm: zynq: Remove board specific compatibility string
clk: zynq: Remove deprecated clock code
arm: zynq: Migrate platform to clock controller
clk: zynq: Add clock controller driver
clk: zynq: Factor out PLL driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The CLOCKSOURCE_OF_DECLARE functions now take a device_node pointer
as their argument, as of the clksrc/cleanup branch in arm-soc.
This patch adapts the bcm_kona_timer driver to the new interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Daudt <csd@broadcom.com>
Cc: John Stultz <john.stultz@linaro.org>
This reverts commit 55a68c23e0.
In order to avoid a collision with dw_apb_timer changes in
the arm-soc tree, revert this change.
I'm leaving it to the arm-soc folks to sort out if they want
to keep the other side of the collision or if they're just going
to back it all out and try again during the next release cycle.
Reported-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Replace the (setup/remove)_irq calls for local timer registration with
(request/free)_irq calls. This generalizes the local timer registration API.
Suggested by Mark Rutland.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Log core clock and Meta timer frequencies during init in architecture
generic code, removing the need for equivalent log messages in SoC
specific code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
dw_apb_timer_init used to search the devicetree for matching timer
devices, making calls to it from board files necessary.
Change the dw_apb_timer_init to work with CLOCKSOURCE_OF_DECLARE.
With this change the function gets called once for each timer node
and tracks these number of calls to attach clockevent and clocksource
devices to the nodes.
Also remove the calls to dw_apb_timer_init from all previous users, as
clocksource_of_init is the default for init_time now.
Tested on the upcoming rk3066 code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
dw_apb_timer_of is the driver part facing devicetree platforms and
calls into dw_apb_timer with the data gathered from the dt.
Currently the two platforms using the dw_apb_timer_of select both
the options for the core timer and the dt addon.
As dw_apb_timer_of always depends on dw_apb_timer let it select
DW_APB_TIMER itself without the need for every platform to do it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Add the possibility to get the clock-frequency from a timer clock instead
of specifying it as dt property. Additionally also add the possibility
to also define a controlling periphal clock for the timer block.
The clock-frequency property is kept to act as fallback if no clocks
are specified.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Currently the dw_apb_timer always expects a separate special timer to be
availbable for the sched_clock. Some devices using dw_apb_timers do not
have this sptimer but can use the clocksource as sched_clock instead.
Therefore enable the driver to distiguish between devices with and without
sptimer based on the devicetree data and select the correct timer as
sched_clock.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Switching between reading the virtual or physical counters is
problematic, as some core code wants a view of time before we're fully
set up. Using a function pointer and switching the source after the
first read can make time appear to go backwards, and having a check in
the read function is an unfortunate block on what we want to be a fast
path.
Instead, this patch makes us always use the virtual counters. If we're a
guest, or don't have hyp mode, we'll use the virtual timers, and as such
don't care about CNTVOFF as long as it doesn't change in such a way as
to make time appear to travel backwards. As the guest will use the
virtual timers, a (potential) KVM host must use the physical timers
(which can wake up the host even if they fire while a guest is
executing), and hence a host must have CNTVOFF set to zero so as to have
a consistent view of time between the physical timers and virtual
counters.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rob Herring <rob.herring@calxeda.com>
This patch adds a clocksource/clockevent driver for the timer found on some
models in the TI-Nspire calculator series. The timer has two 16bit subtimers
within its memory mapped I/O interface but only the first can generate
interrupts. The first subtimer is used to generate clockevents but only if an
interrupt number and register is given.
The interrupt acknowledgement mechanism is a little strange because the
interrupt mask and acknowledge registers are located in another memory mapped
I/O peripheral. The address of this register is passed to the driver through
device tree bindings.
The second subtimer is used as a clocksource because it isn't capable of
generating an interrupt. This subtimer is always added.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add Freescale Vybrid Family period interrupt timer support.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
irq_of_parse_and_map() returns 0 on error, while the code checks for NO_IRQ.
This breaks on platforms that have NO_IRQ != 0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clocksource API has changed slightly, which causes a harmless
warning:
/git/arm-soc/drivers/clocksource/nomadik-mtu.c:259:28: warning: 'nmdk_timer_match' defined but not used [-Wunused-variable]
static struct of_device_id nmdk_timer_match[] __initconst = {
^
Fortunately, the same API change also lets us simplify the code
while removing the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The time.h header seems not to be used by current code.
Removing this include allows the driver to build on other
architecture that do not have this header.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[tweaked commit message and header]
Signed-off-by: John Stultz <john.stultz@linaro.org>
It seems we made a mistake when creating dw_apb_timer_of.c:
picoxcell sched_clock had parts that were not related to
dw_apb_timer, yet we moved them to dw_apb_timer_of, and tried to
use them on socfpga.
This results in system where user/system time is not measured
properly, as demonstrated by
time dd if=/dev/urandom of=/dev/zero bs=100000 count=100
So this patch switches sched_clock to hardware that exists on both
platforms, and adds missing of_node_put() in dw_apb_timer_init().
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Modify clksrc_dbx500_prcmu_read to replace readl() with readl_relaxed().
This speeds up calls to the function by about 40%.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
