- Move qcom driver to bulk clock API (Bjorn Andersson)
- Add Qualcomm QCS404 PCIe controller support (Bjorn Andersson)
- Ensure Qualcomm PERST is asserted for at least 100ms (Niklas Cassel)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Ensure that PERST is asserted for at least 100 ms
PCI: qcom: Add QCS404 PCIe controller support
dt-bindings: PCI: qcom: Add QCS404 to the binding
PCI: qcom: Use clk bulk API for 2.4.0 controllers
- Unify mobiveil register accessors (Hou Zhiqiang)
- Remove MSI_FLAG_MULTI_PCI_MSI since mobiveil hardware doesn't support
Multiple MSI (Hou Zhiqiang)
- Program outbound windows with base address from DT instead of assuming
zero (Hou Zhiqiang)
- Skip "safe" list traversal when it's unnecessary (Hou Zhiqiang)
- Initialize WIN_NUM_0 explicitly for CFG outbound transactions (Hou
Zhiqiang)
- Use WIN_NUM_0 for MEM inbound transactions (Hou Zhiqiang)
- Fix up mobiveil Class Code to PCI_CLASS_BRIDGE_PCI (Hou Zhiqiang)
- Wait for link-up before enumerating devices, not while initializing
host (Hou Zhiqiang)
- Move IRQ chained handler setup out of DT code (Hou Zhiqiang)
- Set primary/secondary/subordinate bus numbers (Hou Zhiqiang)
- Fix "valid device" check to allow root bus device 0 to be
multi-function (Hou Zhiqiang)
- Make DT "gpio_slave" and "apb_csr" properties optional (Hou Zhiqiang)
- Refactor MEM/IO outbound window initialization (Hou Zhiqiang)
- Fix validity check for inbound/outbound window programming (Hou
Zhiqiang)
- Initialize and preserve window control bits (Hou Zhiqiang)
- Fix 64-bit outbound window setup (both CPU and PCI addresses) (Hou
Zhiqiang)
- Move IO port setup to host init (Hou Zhiqiang)
- Fix infinite loop in INTx ISR (Hou Zhiqiang)
- Fix INTx interrupt clearing to avoid missed interrupts (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix INTx interrupt clearing in mobiveil_pcie_isr()
PCI: mobiveil: Fix infinite-loop in the INTx handling function
PCI: mobiveil: Move PCIe PIO enablement out of inbound window routine
PCI: mobiveil: Add upper 32-bit PCI base address setup in inbound window
PCI: mobiveil: Add upper 32-bit CPU base address setup in outbound window
PCI: mobiveil: Mask out hardcoded bits in inbound/outbound windows setup
PCI: mobiveil: Clear the control fields before updating it
PCI: mobiveil: Add configured inbound windows counter
PCI: mobiveil: Fix the valid check for inbound and outbound windows
PCI: mobiveil: Clean-up program_{ib/ob}_windows()
PCI: mobiveil: Remove an unnecessary return value check
PCI: mobiveil: Fix error return values
PCI: mobiveil: Refactor the MEM/IO outbound window initialization
PCI: mobiveil: Make some register updates more readable
PCI: mobiveil: Reformat the code for readability
dt-bindings: PCI: mobiveil: Change gpio_slave and apb_csr to optional
PCI: mobiveil: Fix devfn check in mobiveil_pcie_valid_device()
PCI: mobiveil: Initialize Primary/Secondary/Subordinate bus numbers
PCI: mobiveil: Move IRQ chained handler setup out of DT parse
PCI: mobiveil: Move the link up waiting out of mobiveil_host_init()
PCI: mobiveil: Fix the Class Code field
PCI: mobiveil: Use the 1st inbound window for MEM inbound transactions
PCI: mobiveil: Use WIN_NUM_0 explicitly for CFG outbound window
PCI: mobiveil: Update the resource list traversal function
PCI: mobiveil: Fix PCI base address in MEM/IO outbound windows
PCI: mobiveil: Remove the flag MSI_FLAG_MULTI_PCI_MSI
PCI: mobiveil: Unify register accessors
- Add dwc API support to de-initialize host (Vidya Sagar)
- Clean up dwc DBI,ATU read and write APIs (Vidya Sagar)
- Export dwc APIs to support .remove() so drivers can be modular (Vidya
Sagar)
- Simplify imx6 Kconfig dependencies (Leonard Crestez)
- Fix dra7xx build error when !CONFIG_GPIOLIB (YueHaibing)
* remotes/lorenzo/pci/dwc:
PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB
PCI: imx6: Simplify Kconfig depends on
PCI: dwc: Export APIs to support .remove() implementation
PCI: dwc: Cleanup DBI,ATU read and write APIs
PCI: dwc: Add API support to de-initialize host
If CONFIG_GPIOLIB is not selected the compilation results in the
following build errors:
drivers/pci/controller/dwc/pci-dra7xx.c:
In function dra7xx_pcie_probe:
drivers/pci/controller/dwc/pci-dra7xx.c:777:10:
error: implicit declaration of function devm_gpiod_get_optional;
did you mean devm_regulator_get_optional? [-Werror=implicit-function-declaration]
reset = devm_gpiod_get_optional(dev, NULL, GPIOD_OUT_HIGH);
drivers/pci/controller/dwc/pci-dra7xx.c:778:45: error: ‘GPIOD_OUT_HIGH’
undeclared (first use in this function); did you mean ‘GPIOF_INIT_HIGH’?
reset = devm_gpiod_get_optional(dev, NULL, GPIOD_OUT_HIGH);
^~~~~~~~~~~~~~
GPIOF_INIT_HIGH
Fix them by including the appropriate header file.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix typos in drivers/pci. Comment and whitespace changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
The current INTx handling function clears all interrupts after
handling the first pending; this can potentially cause missing INTx
detection. Fix the code to clear only the handled INTx IRQ.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Acked-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Tested-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
In the loop handling INTx interrupts in mobiveil_pcie_isr(), there is
no code to update the loop control variable, which is causing an
infinite loop.
Fix the code by reading the interrupt status registers inside the
loop.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Acked-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Tested-by: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Move the PCIe PIO master enablement to function mobiveil_host_init().
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Current code erroneously sets-up the lower 32-bit PCI base address in
the inbound window, which results in inbound transactions not working in
64-bit platforms.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Current code erroneously sets-up only the lower 32-bit CPU base address
in the outbound window, which results in outbound transactions not
working in 64-bit platforms.
Fix it.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The lower 10 bits of window size field are hardcoded to zero in HW so
they can't really be changed but the lower 10-bit of PAB_AXI_AMAP_CTRL
register are used for control fields, so while programming inbound and
outbout windows decoding we should mask out the lower 10-bit of window
size to prevent overriding the control bits.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
While programming the inbound and outbound windows in
program_{ib/ob}_windows()
we shoud clear the control fields in the registers before programming
it with a new value to prevent stale bits from older configuration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Current code only keeps track of the number of outbound windows
configured but it does not for inbound windows. Add a counter
to keep track of initialized inbound windows.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
In program_ib/ob_windows() check the window index from the function
parameter instead of the total number of initialized windows to
determine if the specified window is valid.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
In function program_ob_windows(), remove the redundant read
operations to registers PAB_AXI_AMAP_AXI_WIN and PAB_AXI_AMAP_PEX_WIN_H,
and remove the useless definition of 'value'. Rename the parameter
'config_io_bit' to 'type' and then remove the definition of 'type'.
In function program_ib_windows(), remove the definitions of
'pio_ctrl_val' and 'amap_ctrl_dw' and reduce to only one variable
'value' to keep the temporary value read from registers.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The memory for the host controller private structure (struct
mobiveil_pcie) is allocated together with the pci_host_bridge structure
in function devm_pci_alloc_host_bridge(), so it is unnecessary to check
the return value when get the private structure pointer.
Remove the useless check.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Some error return values in the host controller driver are
either unconventional or plain wrong. Update them all with
the expected return values.
Signed-off-by: Hou Zhiqiang <Zhinqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Move the resource type check into an if/else block and only
set-up the outbound window for MEM and IO resource. No functional
change intended.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
To make some register updates more readable use a temporary
value to hold the register value and carry out the update.
Change the register update sequence to:
- Read out the original value from the target register
- Update the value
- Program the updated value back to the register
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reformat the code to make it more readable. No functional
change intended.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Current check for devfn number in mobiveil_pci_valid_device() is
wrong in that it flags as invalid functions present in PCI device 0
in the root bus while it is perfectly valid to access all functions
in PCI device 0 in the root bus.
Update the check in mobiveil_pci_valid_device() to fix the issue.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
The reset value of Primary, Secondary and Subordinate bus numbers is
zero which is a broken setup.
Program a sensible default value for Primary/Secondary/Subordinate
bus numbers.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The irq_set_chained_handler_and_data() call is not dependent on device
tree firmware so it should be moved out of the DT parsing function for
clarity.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: rewritten commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The host initializing sequence does not depend on the PCIe link being
up, so move the link up check right before the code scanning the root
bus for enumeration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Fix up the Class Code field in PCI configuration space and set it to
PCI_CLASS_BRIDGE_PCI.
Move the Class Code fixup to function mobiveil_host_init() where
it belongs.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The inbound and outbound windows have completely separate control
registers sets in the host controller MMIO space. Windows control
register are accessed through an MMIO base address and an offset
that depends on the window index.
Since inbound and outbound windows control registers are completely
separate there is no real need to use different window indexes in the
inbound/outbound windows initialization routines to prevent clashing.
To fix this inconsistency, change the MEM inbound window index to 0,
mirroring the outbound window set-up.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: update commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
As the .map_bus() use the WIN_NUM_0 for CFG transactions,
it is appropriate to pass WIN_NUM_0 explicitly when initializing
the CFG outbound window rather than implicitly relying on the
ob_wins_configure counter.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Code that executes the resource list traversal does not need to
delete any node therefore using the *_safe() API version is
useless.
Replace function resource_list_for_each_entry_safe() with the
resource_list_for_each_entry() counterpart.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The outbound memory windows PCI base addresses should be taken
from the 'ranges' property of DT node to setup MEM/IO outbound
windows decoding correctly instead of being hardcoded to zero.
Update the code to retrieve the PCI base address for each range
and use it to program the outbound windows address decoders
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The Mobiveil internal MSI controller requires separate target addresses,
one per MSI vector; this is clearly incompatible with the Multiple MSI
feature, which requires the same target address for all vectors
requested by an endpoint (ie the Message Address field in the MSI
Capability structure), so the multi MSI feature is clearly not
supported by the host controller driver.
Remove the flag MSI_FLAG_MULTI_PCI_MSI and with it multi MSI support,
fixing the misconfiguration.
Fixes: 1e913e5833 ("PCI: mobiveil: Add MSI support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
It is confusing to have two sets of functions to read/write
registers, some with csr_readl()/csr_writel(), while others with
read_paged_register()/write_paged_register().
In the register space the lower 3KB of 4KB PCIe configure space can be
accessed directly and higher 1KB through a simple paging mechanism.
Unify the register accessors in csr_readl() and csr_writel() by
comparing the register offset with page access boundary 3KB in the
accessor internal so that the paging mechanism is hidden behind
the csr_read()/write() common function calls.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The imx6 driver can be used on imx6sx without enabling support for
imx6q or imx7d but the "depends on" condition doesn't allow that.
Instead of making the condition even longer just make it depend on
"ARCH_MXC || COMPILE_TEST" instead.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Fix a use-after-free in hv_eject_device_work().
Fixes: 05f151a73e ("PCI: hv: Fix a memory leak in hv_eject_device_work()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
The PCI Tegra controller conversion to a device tree configurable
driver in commit d1523b52bf ("PCI: tegra: Move PCIe driver
to drivers/pci/host") implied that code for the driver can be
compiled in for a kernel supporting multiple platforms.
Unfortunately, a blind move of the code did not check that some of the
quirks that were applied in arch/arm (eg enabling Relaxed Ordering on
all PCI devices - since the quirk hook erroneously matches PCI_ANY_ID
for both Vendor-ID and Device-ID) are now applied in all kernels that
compile the PCI Tegra controlled driver, DT and ACPI alike.
This is completely wrong, in that enablement of Relaxed Ordering is only
required by default in Tegra20 platforms as described in the Tegra20
Technical Reference Manual (available at
https://developer.nvidia.com/embedded/downloads#?search=tegra%202 in
Section 34.1, where it is mentioned that Relaxed Ordering bit needs to
be enabled in its root ports to avoid deadlock in hardware) and in the
Tegra30 platforms for the same reasons (unfortunately not documented
in the TRM).
There is no other strict requirement on PCI devices Relaxed Ordering
enablement on any other Tegra platforms or PCI host bridge driver.
Fix this quite upsetting situation by limiting the vendor and device IDs
to which the Relaxed Ordering quirk applies to the root ports in
question, reported above.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[lorenzo.pieralisi@arm.com: completely rewrote the commit log/fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Driver checks for link up three times before giving up, each retry
attempt is printed as an error. Letting users know that PCIe link is
down and in the process of being brought up again is for debug, not an
error condition.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra PCIe has fixed per port SFIO line to signal PERST#, which can be
controlled by AFI port register. However, if a platform routes a
different GPIO to the PCIe slot, then port register cannot control it.
Add support for GPIO based PERST# signal for such platforms. GPIO number
comes from per port PCIe device tree node. PCIe driver probe doesn't
fail if per port "reset-gpios" property is not populated, so platforms
that require this workaround must make sure that the DT property is not
missed in the corresponding device tree.
Link: https://lore.kernel.org/linux-pci/20190705084850.30777-1-jonathanh@nvidia.com/
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[lorenzo.pieralisi@arm.com: squashed in fix in Link]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Export all configuration space access APIs and also other APIs to
support host controller drivers of dwc core based implementations while
adding support for .remove() hook to build their respective drivers as
modules.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cleanup DBI read and write APIs by removing leading "__" (underscore)
from their names as there is no reason to have leading underscores
in the first place in the function definition.
Remove dbi/dbi2 base address parameters as the same behaviour can be
obtained through read and write APIs. Since dw_pcie_{readl/writel}_dbi()
APIs can't be used for ATU read/write as ATU base address could be
different from DBI base address, implement ATU read/write APIs using ATU
base address without using dw_pcie_{readl/writel}_dbi() APIs.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Add an API to group all the tasks to be done to de-initialize host which
can then be called by any dwc core based driver implementations
while adding .remove() support in their respective drivers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
According to the PCI Local Bus specification Revision 3.0,
section 6.8.1.3 (Message Control for MSI), endpoints that
are Multiple Message Capable as defined by bits [3:1] in
the Message Control for MSI can request a number of vectors
that is power of two aligned.
As specified in section 6.8.1.6 "Message data for MSI", the Multiple
Message Enable field (bits [6:4] of the Message Control register)
defines the number of low order message data bits the function is
permitted to modify to generate its system software allocated
vectors.
The MSI controller in the Xilinx NWL PCIe controller supports a number
of MSI vectors specified through a bitmap and the hwirq number for an
MSI, that is the value written in the MSI data TLP is determined by
the bitmap allocation.
For instance, in a situation where two endpoints sitting on
the PCI bus request the following MSI configuration, with
the current PCI Xilinx bitmap allocation code (that does not
align MSI vector allocation on a power of two boundary):
Endpoint #1: Requesting 1 MSI vector - allocated bitmap bits 0
Endpoint #2: Requesting 2 MSI vectors - allocated bitmap bits [1,2]
The bitmap value(s) corresponds to the hwirq number that is programmed
into the Message Data for MSI field in the endpoint MSI capability
and is detected by the root complex to fire the corresponding
MSI irqs. The value written in Message Data for MSI field corresponds
to the first bit allocated in the bitmap for Multi MSI vectors.
The current Xilinx NWL MSI allocation code allows a bitmap allocation
that is not a power of two boundaries, so endpoint #2, is allowed to
toggle Message Data bit[0] to differentiate between its two vectors
(meaning that the MSI data will be respectively 0x0 and 0x1 for the two
vectors allocated to endpoint #2).
This clearly aliases with the Endpoint #1 vector allocation, resulting
in a broken Multi MSI implementation.
Update the code to allocate MSI bitmap ranges with a power of two
alignment, fixing the bug.
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
In Tegra210 AFI design has clamp value for the BIAS pad as 0, which keeps
the bias pad in non power down mode. This is leading to power consumption
of 2 mW in BIAS pad, even if the PCIe partition is powergated. To avoid
unnecessary power consumption, put PEX CLK & BIAS pads in deep power down
mode when PCIe partition is power gated.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra186 and Tegra30 have three PCIe root ports. AFI_PEX2_CTRL register
is defined for third root port. Offset of this register in Tegra186 is
different from Tegra30, so add the offset as part of SoC data structure.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
PRSNT_MAP bit field is programmed to update the slot present status.
PRSNT_SENSE IRQ is triggered when this bit field is programmed, which is
not an error. Add a new if condition to trap PRSNT_SENSE code and print
it with debug log level.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cacheable upstream transactions are supported in Tegra20 and Tegra186
only.
AFI_CACHE_BAR_{0,1}_{ST,SZ} registers are available in Tegra20 to
support cacheable upstream transactions. In Tegra186, AFI_AXCACHE
register is defined instead of AFI_CACHE_BAR_{0,1}_{ST,SZ} to be in line
with its memory subsystem design.
Therefore, program AFI_CACHE_BAR_{0,1}_{ST,SZ} registers only for Tegra20.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Disable controllers which failed to bring the link up and configure
CLKREQ# signals of these controllers as GPIO. This is required to avoid
CLKREQ# signal of inactive controllers interfering with PLLE power down
sequence.
PCIE_CLKREQ_GPIO bits are defined only in Tegra186, however programming
these bits in other SoCs doesn't cause any side effects. Program these
bits for all Tegra SoCs to avoid a conditional check.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
PCIe link up fails with few legacy endpoints if root port advertises both
Gen-1 and Gen-2 speeds in Tegra. This is because link number negotiation
fails if both Gen1 & Gen2 are advertised. Tegra doesn't retry link up by
advertising only Gen1. Hence, the strategy followed here is to initially
advertise only Gen-1 and after link is up, retrain link to Gen-2 speed.
Tegra doesn't support HW autonomous speed change. Link comes up in Gen1
even if Gen2 is advertised, so there is no downside of this change.
This behavior is observed with following two PCIe devices on Tegra:
- Fusion HDTV 5 Express card
- IOGear SIL - PCIE - SATA card
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Recommended UpdateFC threshold in Tegra210 is 0x60 for best performance
of x1 link. Setting this to 0x60 provides the best balance between number
of UpdateFC packets and read data sent over the link.
UpdateFC timer frequency is equal to twice the value of register content
in nsec, i.e (2 * 0x60) = 192 nsec.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The logic which blocks read requests till AFI gets ACK for all outstanding
writes from memory controller does not behave correctly when number of
outstanding writes become more than 32 in Tegra124 and Tegra132.
SW fixup is to prevent writes from accumulating more than 32 by:
- limiting outstanding posted writes to 14
- modifying Gen1 and Gen2 UpdateFC timer frequency
UpdateFC timer frequency is equal to twice the value of register content
in nsec. These settings are recommended after stress testing with
different values.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Sometimes link speed change from Gen2 to Gen1 fails due to instability
in deskew logic on lane-0 in Tegra210. Increase the deskew retry time
to resolve this issue.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Enable xclk clock clamping when entering L1. Clamp threshold will
determine the time spent waiting for clock module to turn on xclk after
signaling it. Default threshold value in Tegra124 and Tegra210 is not
enough to turn on xclk clock. Increase the clamp threshold to meet the
clock module timing in Tegra124 and Tegra210. Default threshold value is
enough in Tegra20, Tegra30 and Tegra186.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
PM message are truncated while entering L1 or L2, which is resulting in
receiver errors. Set the required bit to finish processing DLLP before
link enter L1 or L2.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Outstanding write counter in AFI is used to generate idle signal to
dynamically gate the AFI clock. When there are 32 outstanding writes
from AFI to memory, the outstanding write counter overflows and
indicates that there are "0" outstanding write transactions.
When memory controller is under heavy load, write completions to AFI
gets delayed and AFI write counter overflows. This causes AFI clock gating
even when there are outstanding transactions towards memory controller
resulting in a system hang.
Disable dynamic clock gating of AFI clock to avoid system hang.
CLKEN_OVERRIDE bit is not defined in Tegra20 and Tegra30, however
programming this bit doesn't cause any side effects. Program this
bit for all Tegra SoCs to avoid conditional check.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Enable opportunistic UpdateFC and ACK to allow data link layer send
pending ACKs and UpdateFC packets when link is idle instead of waiting
for timers to expire. This improves the PCIe performance due to better
utilization of PCIe bandwidth.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
UPHY electrical programming guidelines are documented in Tegra210 TRM.
Program these electrical settings for proper eye diagram in Gen1 and Gen2
link speeds.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Default root port setting hides AER capability. This patch enables the
advertisement of AER capability by root port.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra124, Tegra132, Tegra210 and Tegra186 support Gen2 link speed. After
PCIe link is up in Gen1, set target link speed as Gen2 and retrain link.
Link switches to Gen2 speed if Gen2 capable end point is connected,
otherwise the link stays in Gen1.
Per PCIe 4.0r0.9 sec 7.6.3.7 implementation note, driver needs to wait for
PCIe LTSSM to come back from recovery before retraining the link.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The PCIe host power up sequence requires to program AFI(AXI to FPCI
bridge) registers first and then PCIe registers, otherwise AFI register
settings may not latch to PCIe IP.
PCIe root port starts LTSSM as soon as PCIe xrst is deasserted.
So deassert PCIe xrst after programming PCIe registers.
Modify PCIe power up sequence as follows:
- Power ungate PCIe partition
- Enable AFI clock
- Deassert AFI reset
- Program AFI registers
- Enable PCIe clock
- Deassert PCIe reset
- Program PCIe PHY
- Program PCIe pad control registers
- Program PCIe root port registers
- Deassert PCIe xrst to start LTSSM
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra PCIe has register specifications for:
- AXI to FPCI(AFI) bridge
- Multiple PCIe root ports
- PCIe PHY
- PCIe pad control
Rearrange Tegra PCIe driver functions so that each function programs
the required module only.
- tegra_pcie_enable_controller(): Program AFI module and enable PCIe
controller
- tegra_pcie_phy_power_on(): Bring up PCIe PHY
- tegra_pcie_apply_pad_settings(): Program PCIe REFCLK pad settings
- tegra_pcie_enable_ports(): Program each root port and bring up PCIe
link
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Unroll the PCIe power on sequence if any one of the steps fails in
tegra_pcie_power_on().
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Stratix 10 PCIe controller does not support Type 1 to Type 0 conversion
as previous version (V1) does so the PCIe controller configuration
mechanism needs to send Type 0 config TLP if the target bus number
matches with the secondary bus number.
Implement a function to form a TLP header that depends on the PCIe
controller version, so that the header can be formed according to
specific host controller HW internals, fixing the type conversion issue.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Bring PHY support for the Armada8k driver.
The Armada8k IP only supports x1, x2 or x4 link widths. Iterate over
the DT 'phys' entries and configure them one by one. Use
phy_set_mode_ext() to make use of the submode parameter (initially
introduced for Ethernet modes). For PCI configuration, let the submode
be the width (1, 2, 4, etc) so that the PHY driver knows how many
lanes are bundled. Do not error out in case of error for compatibility
reasons.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, there is only a 1 ms sleep after asserting PERST.
Reading the datasheets for different endpoints, some require PERST to be
asserted for 10 ms in order for the endpoint to perform a reset, others
require it to be asserted for 50 ms.
Several SoCs using this driver uses PCIe Mini Card, where we don't know
what endpoint will be plugged in.
The PCI Express Card Electromechanical Specification r2.0, section
2.2, "PERST# Signal" specifies:
"On power up, the deassertion of PERST# is delayed 100 ms (TPVPERL) from
the power rails achieving specified operating limits."
Add a sleep of 100 ms before deasserting PERST, in order to ensure that
we are compliant with the spec.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.5+
Altera MSI IP is a soft IP and is only available after
an FPGA image (with design containing it) is programmed.
Make driver modulable to support use case FPGA image is programmed the
after kernel has booted, so that the driver can be loaded upon request.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Altera PCIe Rootport IP is a soft IP and is only available after
an FPGA image (whose design contains it) is programmed.
Make driver modulable to support use cases when FPGA image is
programmed after the kernel has booted, so that the driver
can be loaded upon request.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The QCS404 platform contains a PCIe version 2.4.0 controller and a
Qualcomm PCIe2 PHY. The driver already supports version 2.4.0, for the
IPQ4019, but this support touches clocks and resets related to the PHY
as well and there's no upstream driver for the PHY.
On QCS404 we must initialize the PHY, so a separate PHY driver is
implemented to take care of this and the controller driver is updated to
not require the PHY related resources. This is done by relying on the
fact that operations in both the clock and reset framework are NOPs when
passed NULL, so we can isolate this change to only the
qcom_pcie_get_resources_2_4_0() function.
For QCS404 we also need to enable the AHB (iface) clock, in order to
access the register space of the controller, but as this is not part of
the IPQ4019 DT binding this is only added for new users of the 2.4.0
controller.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Before introducing the QCS404 platform, which uses the same PCIe
controller as IPQ4019, migrate this to use the bulk clock API, in order
to make the error paths slighly cleaner.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
- Use DMA-API to get tegra MSI address to prevent device DMA from
generating unwanted MSIs (Vidya Sagar)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Use the DMA-API to get the MSI address
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
- Work around iproc CRS completion issues (Srinath Mannam)
- Allow smaller iproc outbound windows so driver can work on 32-bit
systems (Srinath Mannam)
- Use iproc-specific config read for PAXBv2 (not PAXB) (Srinath Mannam)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Enable iProc config read for PAXBv2
PCI: iproc: Allow outbound configuration for 32-bit I/O region
PCI: iproc: Add CRS check in config read
- Simplify imx7d_pcie_wait_for_phy_pll_lock() by using
regmap_read_poll_timeout() (Andrey Smirnov)
- Drop imx6_pcie_wait_for_link() in favor of the more generic
dw_pcie_wait_for_link() (Andrey Smirnov)
- Return -ETIMEDOUT instead of -EINVAL from
imx6_pcie_wait_for_speed_change() (Andrey Smirnov)
- Remove unused PCIE_PL_PFLR_* constants from imx6 (Andrey Smirnov)
- Use shared PHY debug register definitions in imx6 (Andrey Smirnov)
- Use BIT() in imx6 (Andrey Smirnov)
- Simplify imx6 PHY bit operations (Andrey Smirnov)
- Simplify imx6 pcie_phy_poll_ack() (Andrey Smirnov)
- Use data types that match actual imx6 PHY register width (Andrey
Smirnov)
- Mark imx6 suspend support with drvdata flags instead of checking
variants (Andrey Smirnov)
- Sleep instead of delay in imx6_pcie_enable_ref_clk() (Andrey Smirnov)
* remotes/lorenzo/pci/imx:
PCI: imx6: Use usleep_range() in imx6_pcie_enable_ref_clk()
PCI: imx6: Use flags to indicate support for suspend
PCI: imx6: Restrict PHY register data to 16-bit
PCI: imx6: Simplify pcie_phy_poll_ack()
PCI: imx6: Simplify bit operations in PHY functions
PCI: imx6: Make use of BIT() in constant definitions
PCI: dwc: imx6: Share PHY debug register definitions
PCI: imx6: Remove PCIE_PL_PFLR_* constants
PCI: imx6: Return -ETIMEOUT from imx6_pcie_wait_for_speed_change()
PCI: imx6: Drop imx6_pcie_wait_for_link()
PCI: imx6: Simplify imx7d_pcie_wait_for_phy_pll_lock()
- Restore R-Car PCIe link early in resume (Kazufumi Ikeda)
- Fix Hyper-V PCI ejection memory leak (Dexuan Cui)
- Cleanup Hyper-V PCI slots on module unload (Dexuan Cui)
- Cleanup Hyper-V PCI slot on device removal to address a race (Dexuan
Cui)
* remotes/lorenzo/pci/controller-fixes:
PCI: hv: Add pci_destroy_slot() in pci_devices_present_work(), if necessary
PCI: hv: Add hv_pci_remove_slots() when we unload the driver
PCI: hv: Fix a memory leak in hv_eject_device_work()
PCI: rcar: Add the initialization of PCIe link in resume_noirq()
Establishing a PCIe link can take a while; allow asynchronous probing so
that link establishment can happen in the background while other devices
are being probed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently DWC host does not support the remove callback, but nothing
prevents us from supporting it.
Save the root bus for clean up work in driver remove code paths to allow
DWC host drivers to implement their remove hook as, eg:
static int foo_pcie_remove(struct platform_device *pdev)
{
...
pci_stop_root_bus(pp->root_bus);
pci_remove_root_bus(pp->root_bus);
dw_pcie_free_msi(pp);
...
}
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Use devm_pci_alloc_host_bridge() to simplify the error code path. This
also fixes a leak in the dw_pcie_host_init() error path.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
CC: stable@vger.kernel.org # v4.13+
If we ever did MSI-related initializations, we need to call
dw_pcie_free_msi() in the error code path.
Remove the IS_ENABLED(CONFIG_PCI_MSI) check for MSI init because
pci_msi_enabled() already has a stub for !CONFIG_PCI_MSI.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
To avoid a memory leak, free the page allocated for MSI IRQ in
dw_pcie_free_msi().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Check msi_irq variable before calling irq_set_chained_handler() and
irq_set_handler_data(), lest we call those functions for an invalid MSI
IRQ.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Move the device class fudge to a proper fixup function, and remove
qcom_pcie_rd_own_conf() which has become useless.
dw_pcie_setup_rc() already did the right thing, but it's broken
on older qcom chips, such as 8064.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The iProc host controller allows only a subset of physical address space as
target of inbound PCI memory transaction addresses.
PCI device memory transactions targeting memory regions that are not
allowed for inbound transactions in the host controller are rejected by the
host controller and cannot reach the upstream buses.
The firmware device tree description defines the DMA ranges that are
addressable by devices DMA transactions; parse the device tree dma-ranges
property and add its ranges to the PCI host bridge dma_ranges list; the
iova_reserve_pci_windows() call executed at iommu_dma_init_domain() will
reserve the IOVA address ranges that are not addressable (ie memory holes
in the dma-ranges set) so that they are not allocated to PCI devices for
DMA transfers.
All allowed address ranges are listed in the dma-ranges DT parameter. For
example:
dma-ranges = < \
0x43000000 0x00 0x80000000 0x00 0x80000000 0x00 0x80000000 \
0x43000000 0x08 0x00000000 0x08 0x00000000 0x08 0x00000000 \
0x43000000 0x80 0x00000000 0x80 0x00000000 0x40 0x00000000>
In the above example of dma-ranges, memory address from
0x0 - 0x80000000,
0x100000000 - 0x800000000,
0x1000000000 - 0x8000000000 and
0x10000000000 - 0xffffffffffffffff.
are not allowed to be used as inbound addresses.
Based-on-a-patch-by: Oza Pawandeep <oza.oza@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: fix function prototype style]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Configure the Resizable BAR capability to advertise the smallest size
(1MB) for a couple of reasons:
- Host side resource allocation of BAR fails for larger sizes
- Endpoint function driver does not allocate memory for all supported
sizes in the Resizable BAR capability.
If and when there is a usecase required to add more flexibility using
the Resizable BAR capability, this can be revisited.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe EP support for AM654x Platforms in pci-keystone.c
Link: https://lore.kernel.org/linux-pci/20190325093947.32633-15-kishon@ti.com/
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: made dev_vdbg() call a comment]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
imx6_pcie_enable_ref_clk() is never called in atomic context, so
there's no need to use udelay(). Replace it with usleep_range().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Now that driver data has flags variable that can be used to indicate
quirks/features supported we can switch the code to use it instead of
having a special function that does so based on variant alone. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
PHY registers on i.MX6 are 16-bit wide, so we can get rid of explicit
masking if we restrict pcie_phy_read()/pcie_phy_write() to use 'u16'
instead of 'int'. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Simplify pcie_phy_poll_ack() by incorporating shifting into constant
definition and convert the code to use 'bool'. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Simplify the code by incorporating left shifts into constant
definitions as well as using FIELD_PREP/GENMASK. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
