The DMA is broken on this specific device for some unknown
reason (probably badly designed or plain broken interface
electronics) and will only work with PIO. Other users of
the same hardware does not have this problem.
Add a specific quirk so that this Gemini device gets
DMA turned off. Also fix up some code around passing the
port information around in probe while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Unlike SoC-specific driver, generic ahci_platform driver doesn't
have any chances to control resets.
This adds AHCI_PLATFORM_GET_RESETS to ahci_platform_get_resources()
on the generic driver to enable reset control support.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support to get and control a list of resets for the device
as optional and shared. These resets must be kept de-asserted until
the device is enabled.
This is specified as shared because some SoCs like UniPhier series
have common reset controls with all ahci controller instances.
However, according to Thierry's view,
https://www.spinics.net/lists/linux-ide/msg55357.html
some hardware-specific drivers already use their own resets,
and the common reset make a path to occur double controls of resets.
The ahci_platform_get_resources() can get and control the reset
only when the second argument includes AHCI_PLATFORM_GET_RESETS bit.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add an extra argument to ahci_platform_get_resources(), that is
for the bitmap representing the resource to get in this function.
Currently there is no resources to be defined, so all the callers set
'0' to the argument.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer;
also offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types
-----BEGIN PGP SIGNATURE-----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=eTIC
-----END PGP SIGNATURE-----
Merge tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer; also
offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types"
* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
ASoC: adav80x: mark expected switch fall-through
ASoC: da7219: Add delays to capture path to remove DC offset noise
ALSA: usb-audio: Mark expected switch fall-through
ALSA: mixart: Mark expected switch fall-through
ALSA: opl3: Mark expected switch fall-through
ALSA: hda/ca0132 - Add exit commands for Recon3D
ALSA: hda/ca0132 - Change mixer controls for Recon3D
ALSA: hda/ca0132 - Add Recon3D input and output select commands
ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
ALSA: hda/ca0132 - Add Recon3D startup functions and setup
ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
ALSA: hda/ca0132 - Add Recon3D pincfg
ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
ALSA: hda/ca0132 - Add alt_functions unsolicited response
ALSA: hda/ca0132 - Clean up ca0132_init function.
ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
ASoC: wm_adsp: Make DSP name configurable by codec driver
ASoC: wm_adsp: Declare firmware controls from codec driver
ASoC: max98373: Added software reset register to readable registers
ASoC: wm_adsp: Correct DSP pointer for preloader control
...
According to documentation, setting of PHY registers is unnecessary with
R-Car Gen3. The registers are not even described. So, don't initialize
them.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since R-Car Gen2, a new bit has been introduced to the interrupt mask
register. Update the code to handle it properly as well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltU8z0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5X8H/2fJr7m3k242+t76
sitwvx1eoPqTgryW59dRKm9IuXAGA+AjauvHzaz1QxomeQa50JghGWefD0eiJfkA
1AphQ/24EOiAbbVk084dAI/C2p122dE4D5Fy7CrfLnuouyrbFaZI5STbnrRct7sR
9deeYW0GDHO1Uenp4WDCj0baaqJqaevZ+7GG09DnWpya2nQtSkGBjqn6GpYmrfOU
mqFuxAX8mEOW6cwK16y/vYtnVjuuMAiZ63/OJ8AQ6d6ArGLwAsdn7f8Fn4I4tEr2
L0d3CRLUyegms4++Dmlu05k64buQu46WlPhjCZc5/Ts4kjrNxBuHejj2/jeSnUSt
vJJlibI=
=42a5
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rc6' into for-4.19/block2
Pull in 4.18-rc6 to get the NVMe core AEN change to avoid a
merge conflict down the line.
Signed-of-by: Jens Axboe <axboe@kernel.dk>
To support future compile-time sizeof() checks that will be able to
validate the length of sense buffers, this removes the only dynamically
allocated sense buffers in the tree by putting the 96 byte sense buffers
on the stack.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are two modes in which DEVSLP can be entered. The OS initiated or
hardware autonomous.
In hardware autonomous mode, BIOS configures the AHCI controller and the
device to enable DEVSLP. But they may not be ideal for all cases. So in
this case, OS should be able to reconfigure DEVSLP register.
Currently if the DEVSLP is already enabled, we can't set again as it will
simply return. There are some systems where the firmware is setting high
DITO by default, in this case we can't modify here to correct settings.
With the default in several seconds, we are not able to transition to
DEVSLP.
This change will allow reconfiguration of devslp register if DITO is
different.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We have seen that on some platforms, SATA device never show any DEVSLP
residency. This prevent power gating of SATA IP, which prevent system
to transition to low power mode in systems with SLP_S0 aka modern
standby systems. The PHY logic is off only in DEVSLP not in slumber.
Reference:
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets
/332995-skylake-i-o-platform-datasheet-volume-1.pdf
Section 28.7.6.1
Here driver is trying to do read-modify-write the devslp register. But
not resetting the bits for which this driver will modify values (DITO,
MDAT and DETO). So simply reset those bits before updating to new values.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
One of the requirement for modern x86 system to enter lowest power mode
(SLP_S0) is SATA IP block to be off. This is true even during when
platform is suspended to idle and not only in opportunistic (runtime)
suspend.
Several of these system don't have traditional ACPI S3, so it is
important that they enter SLP_S0 state, to avoid draining battery even
during suspend. So it is important that out of the box Linux installation
reach this state.
SATA IP block doesn't get turned off till SATA is in DEVSLP mode. Here
user has to either use scsi-host sysfs or tools like powertop to set
the sata-host link_power_management_policy to min_power.
This change sets by default link power management policy to min_power
with partial (preferred) or slumber support on idle for some platforms.
To avoid regressions, the following conditions are used:
- User didn't override the policy from module parameter
- The kernel config is already set to use med_power_with_dipm or deeper
- System is a SLP_S0 capable using ACPI low power idle flag
This combination will make sure that systems are fairly recent and
since getting shipped with SLP_S0 support, the DEVSLP function
is already validated.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently when min_power policy is selected, the partial low power state
is not entered and link will try aggressively enter to only slumber state.
Add a new policy which still enable DEVSLP but also try to enter partial
low power state. This policy is presented as "min_power_with_partial".
For information the difference between partial and slumber
Partial – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ns.
Slumber – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ms.
Devslp – PHY logic is powered down. The link PM exit latency from this
state to active state maximum is 20 ms, unless otherwise specified by
DETO.
Suggested-and-reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since ahci_platform_put_resources() use target_pwrs after "devm_" freed
it, we cannot use devm_kcalloc for allocating target_pwrs.
This reverts commit bd0038b1b4.
Reported-and-reviwed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replace the explicit clock handling to enable/disable the SATA module by
calls to Runtime PM.
This makes the driver independent of actual SoC clock/power hierarchies,
and is needed to support virtualization, where the guest is not in full
control of power management.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Defining `ATA_DEBUG` there are a lof of messages like below in the log.
[ 16.345472] ata_sg_setup: 1 sg elements mapped
As that is too verbose, only output these messages in verbose debug.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Defining `ATA_DEBUG` nothing can be really seen, as the log is spammed
with CDB messages.
Therefore, guard the print by `ATA_VERBOSE_DEBUG`.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Like phys, target_pwrs could be allocated with devm_ function
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The documentation about parameter for ahci_platform_shutdown has a typo.
This fix the following build warning:
drivers/ata/libahci_platform.c:693: warning: Function parameter or member 'pdev' not described in 'ahci_platform_shutdown'
drivers/ata/libahci_platform.c:693: warning: Excess function parameter 'dev' description in 'ahci_platform_shutdow
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_sff_data_xfer_noirq() is invoked via the ->sff_data_xfer hook. The
latter is invoked by ata_pio_sector(), atapi_send_cdb() and
__atapi_pio_bytes() which in turn is invoked by ata_sff_hsm_move().
The latter function requires that the "ap->lock" lock is held which
needs to be taken with disabled interrupts.
There is no need have to have ata_sff_data_xfer_noirq() which invokes
ata_sff_data_xfer32() with disabled interrupts because at this point the
interrupts are already disabled.
Remove the function and its references to it and replace all callers
with ata_sff_data_xfer32().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the ALL bit is set in the ZBC_OUT command, the command zone ID field
(block) should be ignored.
Reported-by: David Butterfield <david.butterfield@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The block (LBA) specified must not exceed the last addressable LBA,
which is dev->nr_sectors - 1. So fix the correct check is
"if (block >= dev->n_sectors)" and not "if (block > dev->n_sectords)".
Additionally, the asc/ascq to return for an LBA that is not a zone start
LBA should be ILLEGAL REQUEST, regardless if the bad LBA is out of
range.
Reported-by: David Butterfield <david.butterfield@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
This should also be using the default LPM policy for mobile chipsets so
add the PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
There have been several reports of LPM related hard freezes about once
a day on multiple Lenovo 50 series models. Strange enough these reports
where not disk model specific as LPM issues usually are and some users
with the exact same disk + laptop where seeing them while other users
where not seeing these issues.
It turns out that enabling LPM triggers a firmware bug somewhere, which
has been fixed in later BIOS versions.
This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM
for dealing with this.
The ahci_broken_lpm() function contains DMI match info for the 4 models
which are known to be affected by this and the DMI BIOS date field for
known good BIOS versions. If the BIOS date is older then the one in the
table LPM will be disabled and a warning will be printed.
Note the BIOS dates are for known good versions, some older versions may
work too, but we don't know for sure, the table is using dates from BIOS
versions for which users have confirmed that upgrading to that version
makes the problem go away.
Unfortunately I've been unable to get hold of the reporter who reported
that BIOS version 2.35 fixed the problems on the W541 for him. I've been
able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older
dmidecode, but I don't know the exact BIOS date as reported in the DMI.
Lenovo keeps a changelog with dates in their release notes, but the
dates there are the release dates not the build dates which are in DMI.
So I've chosen to set the date to which we compare to one day past the
release date of the 2.34 BIOS. I plan to fix this with a follow up
commit once I've the necessary info.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pointers sdev0 and sdev1 are being assigned but are never used hence they
are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'sdev0' set but not used [-Wunused-but-set-variable]
warning: variable 'sdev1' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 2623c7a5f2 ("libata: add refcounting to ata_host") v4.17+ introduced
refcounting to ata_host and will increase or decrease the refcount when
adding or deleting transport ATA port.
Now the ata host for libsas is embedded in domain_device, and the ->kref
member is not initialized. Afer we add ata transport class, ata_host_get()
will be called when adding transport ATA port and a warning will be
triggered as below:
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 2 PID: 103 at
lib/refcount.c:153 refcount_inc+0x40/0x48 ...... Call trace:
refcount_inc+0x40/0x48
ata_host_get+0x10/0x18
ata_tport_add+0x40/0x120
ata_sas_tport_add+0xc/0x14
sas_ata_init+0x7c/0xc8
sas_discover_domain+0x380/0x53c
process_one_work+0x12c/0x288
worker_thread+0x58/0x3f0
kthread+0xfc/0x128
ret_from_fork+0x10/0x18
And also when removing transport ATA port ata_host_put() will be called and
another similar warning will be triggered. If the refcount decreased to
zero, the ata host will be freed. But this ata host is only part of
domain_device, it cannot be freed directly.
So we have to change this embedded static ata host to a dynamically
allocated ata host and initialize the ->kref member. To use ata_host_get()
and ata_host_put() in libsas, we need to move the declaration of these
functions to the public libata.h and export them.
Fixes: b6240a4df0 ("scsi: libsas: add transport class for ATA devices")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Taras Kondratiuk <takondra@cisco.com>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can never pass in the internal tag to this helper, it'll
always be the hardware tag. So there's no need to check and
do an internal translation of that tag.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
We need to iterate all commands, including the internal one,
for ATAPI error handling.
Fixes: 28361c4036 ("libata: add extra internal command")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes the following sparse warning:
drivers/ata/ahci_mvebu.c:85:5: warning:
symbol 'ahci_mvebu_stop_engine' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently smatch warns of possible Spectre-V1 issue in ahci_led_store():
drivers/ata/libahci.c:1150 ahci_led_store() warn: potential spectre issue 'pp->em_priv' (local cap)
Userspace controls @pmp from following callchain:
em_message->store()
->ata_scsi_em_message_store()
-->ap->ops->em_store()
--->ahci_led_store()
After the mask+shift @pmp is effectively an 8b value, which is used to
index into an array of length 8, so sanitize the array index.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A number of resources remain powered to support hotplug. On platforms
I've worked with, allowing the ahci_platform to suspend saves about
150mW. This patch enables rpm and allows the device to be auto-suspended
through sysfs.
Signed-off-by: Samuel Morris <samorris@lexmark.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This change balances out the final ahci_port_resume in port_start to
ensure reference counts are correct after port stop.
Signed-off-by: Samuel Morris <samorris@lexmark.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also
taking target updates which are mostly minor except for the tcmu
refactor. The only real core change to worry about is the removal of
high page bouncing (in sas, storvsc and iscsi). This has been well
tested and no problems have shown up so far.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWx1pbCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUucAP42pccS
ziKyiOizuxv9fZ4Q+nXd1A9zhI5tqqpkHjcQegEA40qiZSi3EKGKR8W0UpX7Ntmo
tqrZJGojx9lnrAM2RbQ=
=NMXg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
Pull libata updates from Tejun Heo:
- libata has always been limiting the maximum queue depth to 31, with
one entry set aside mostly for historical reasons. This didn't use to
make much difference but Jens found out that modern hard drives can
actually perform measurably better with the extra one queue depth.
Jens updated libata core so that it can make use of full 32 queue
depth
- Damien updated command retry logic in error handling so that it
doesn't unnecessarily retry when upper layer (SCSI) is gonna handle
them
- A couple misc changes
* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_fsl: use the right type for tag bitshift
ahci: enable full queue depth of 32
libata: don't clamp queue depth to ATA_MAX_QUEUE - 1
libata: add extra internal command
sata_nv: set host can_queue count appropriately
libata: remove assumption that ATA_MAX_QUEUE - 1 is the max
libata: use ata_tag_internal() consistently
libata: bump ->qc_active to a 64-bit type
libata: convert core and drivers to ->hw_tag usage
libata: introduce notion of separate hardware tags
libata: Fix command retry decision
libata: Honor RQF_QUIET flag
libata: Make ata_dev_set_mode() less verbose
libata: Fix ata_err_string()
libata: Fix comment typo in ata_eh_analyze_tf()
sata_nv: don't use block layer bounce buffer
ata: hpt37x: Convert to use match_string() helper
