There are no more users of at24_platform_data. Remove the relevant
header and modify the driver code to not use it anymore.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Within at24_loop_until_timeout the timestamp used for timeout checking
is recorded after the I2C transfer and sleep_range(). Under high CPU
load either the execution time for I2C transfer or sleep_range() could
actually be larger than the timeout value. Worst case the I2C transfer
is only tried once because the loop will exit due to the timeout
although the EEPROM is now ready.
To fix this issue the timestamp is recorded at the beginning of each
iteration. That is, before I2C transfer and sleep. Then the timeout
is actually checked against the timestamp of the previous iteration.
This makes sure that even if the timeout is reached, there is still one
more chance to try the I2C transfer in case the EEPROM is ready.
Example:
If you have a system which combines high CPU load with repeated EEPROM
writes you will run into the following scenario.
- System makes a successful regmap_bulk_write() to EEPROM.
- System wants to perform another write to EEPROM but EEPROM is still
busy with the last write.
- Because of high CPU load the usleep_range() will sleep more than
25 ms (at24_write_timeout).
- Within the over-long sleeping the EEPROM finished the previous write
operation and is ready again.
- at24_loop_until_timeout() will detect timeout and won't try to write.
Signed-off-by: Wang Xin <xin.wang7@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Provide a flexible way to determine the addressing bits of eeprom.
Pass the addressing bits to driver through address-width property.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Move the code responsible for creating the dummy i2c clients used by
chips taking multiple slave addresses to a separate function.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Peter Rosin <peda@axentia.se>
This allows us to drop two opencoded for loops. We also don't need to
check if the i2c client is NULL before calling i2c_unregister_device().
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Peter Rosin <peda@axentia.se>
We now have a managed variant of nvmem_register(). Use it
in at24_probe().
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Peter Rosin <peda@axentia.se>
Commit feb2f19b1e ("eeprom: at24: move platform data processing into
a separate routine") introduced a bug where we incorrectly retireve the
at24_chip_data structure. Remove the unnecessary ampersand operator.
Fixes: feb2f19b1e ("eeprom: at24: move platform data processing into a separate routine")
Reported-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Replace the GPL (or later) header with the SPDX identifier
for GPL-2.0+.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save one call and make code prettier by checking the i2c functionality
in the beginning of at24_probe(), saving the relevant values and
reusing them later.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align the broken line with the opening parenthesis to stay consistent
with the rest of the driver code.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the newline between the nvmem registration and its return value
check. This is consistent with the rest of the driver code.
Add a missing newline between two pdata checks to stay consistent with
all the others.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in at24_probe() is pretty mangled. It can be cleaned up a bit
by doing things one by one.
Let's group the code by logic: parse and verify pdata, initialize the
regmap, allocate and fill the fields of at24_data, allocate dummy i2c
devices, initialize pm & register with nvmem.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all fields from at24_platform_data are needed in at24_data. Let's
keep just the ones we need and not carry the whole platform_data
structure all the time.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver can receive its device data from different sources
depending on the system. Move the entire code processing platform data,
device tree and acpi into a separate function.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new probe() style for i2c drivers.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper function for accessing the device struct of the base
i2c client. This routine is named in a way that reflects its purpose
unlike the previously hand-coded dereferencing.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper variable for the size we want to allocate with
devm_kzalloc() and save an ugly line break.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use the &client->dev construct all over in at24_probe(). Use
a helper variable which is more readable and allows to avoid a couple
unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reflect the purpose of this variable: it contains platform data so name
it such.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As preparation for at24_probe() refactoring: rename at24_get_pdata()
to at24_properties_to_pdata(). We're doing it because we'll move the
pdata parsing code into a separate function which will be called
at24_get_pdata(). Current routine with that name actually parses
the device properties so change its name to reflect its purpose.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We support certain models the size of which is not a power of 2. This
is not a reason to emit a warning.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can reuse ret instead of defining a loop-local status variable.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can reuse ret instead of defining a loop-local status variable.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are just two left-overs from times when this driver was bigger.
They are not really useful anymore. Remove them.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arrange declarations of local variables by line length as visually
it's easier to read.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure only needs to exist during the call to nvmem_register().
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use our own mutex for locking. Disable the regmap-specific locking.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add all supported at24 variants to the of_match table.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
AT24 EEPROMs have a write-protect pin, which - when pulled high -
inhibits writes to the upper quadrant of memory (although it has been
observed that on some chips it disables writing to the entire memory
range).
On some boards, this pin is connected to a GPIO and pulled high by
default, which forces the user to manually change its state before
writing. On linux this means that we either need to hog the line all
the time, or set the GPIO value before writing from outside of the
at24 driver.
Make the driver check if the write-protect GPIO was defined in the
device tree and pull it low whenever writing to the EEPROM.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The chip size passed via devicetree, i2c, or acpi device ids is now no
longer limited to a power of two. So the temporary fix can be removed.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Fundamental properties such as capacity and page size differ among
at24-type chips. But these chips do not have an id register, so this
can't be discovered at runtime.
Traditionally, at24-type eeprom properties were determined in two ways:
- by passing a 'struct at24_platform_data' via platform_data, or
- by naming the chip type in the devicetree, which passes a 'magic
number' to probe(), which is then converted to a 'struct
at24_platform_data'.
Recently a bug was discovered because the magic number rounds down all
chip sizes to the lowest power of two. This was addressed by
a work-around commit 5478e478ee ("eeprom: at24: correctly set the
size for at24mac402"), with the wish that magic numbers should over
time be converted to structs.
This patch replaces the magic numbers with 'struct at24_chip_data'.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
A regmap_config struct is pretty big and declaring two of them
statically just to tweak the reg_bits value adds unnecessary bloat.
Declare the regmap config locally in at24_probe() instead.
Bloat-o-meter output for ARM:
add/remove: 0/2 grow/shrink: 1/0 up/down: 4/-272 (-268)
Function old new delta
at24_probe 1560 1564 +4
regmap_config_8 136 - -136
regmap_config_16 136 - -136
Total: Before=7012, After=6744, chg -3.82%
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
There are a couple symbols defined in the driver source file which are
missing the at24_ prefix. This patch fixes that.
For module params: use module_param_named() in order to not break
userspace.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Some multi-address eeproms in the at24 family may not automatically
roll-over reads to the next slave address. On those eeproms, reads
that straddle slave boundaries will not work correctly.
Solution:
Mark such eeproms with a flag that prevents reads straddling
slave boundaries. Add the AT24_FLAG_NO_RDROL flag to the eeprom
entry in the device_id table, or add 'no-read-rollover' to the
eeprom devicetree entry.
Note that I have not personally enountered an at24 chip that
does not support read rollovers. They may or may not exist.
However, my hardware requires this functionality because of
a quirk.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Add regmap-based read function and instead of using three different
read functions (standard, mac, serial) use just one and factor out the
read offset adjustment for mac and serial to at24_adjust_read_offset.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Remove the old and now unused write functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Change return type of at24_translate_offset to *at24_client to make
member regmap accessible for subsequent patches of this series.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This patch adds basic regmap support to be used by subsequent
patches of this series.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Trying to read the MAC address from an eeprom that has an offset that
is not a multiple of 4 causes an error currently.
Fix it by changing the nvmem stride to 1.
Cc: stable@vger.kernel.org
Signed-off-by: David Lechner <david@lechnology.com>
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The at24 driver creates dummy I2C devices to access offsets in the chip
that are outside the area supported using a single I2C address. It is not
meaningful to use runtime PM to such devices; the system firmware (ACPI)
does not know about these devices nor runtime PM was enabled for them.
Always use the real device instead of the dummy ones.
Fixes: 98e8201039 ("eeprom: at24: enable runtime pm support")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Sven Van Asbroeck on a 24AA16/24LC16B <svendev@arcx.com>
[Bartosz: rebased on top of previous fixes for 4.15, tweaked the
commit message]
[Sven: fixed Bartosz's rebase]
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
So far we completely rely on the caller to provide valid arguments.
To be on the safe side perform an own sanity check.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Chip datasheet mentions that word addresses other than the actual
start position of the MAC delivers undefined results. So fix this.
Current implementation doesn't work due to this wrong offset.
Cc: stable@vger.kernel.org
Fixes: 0b813658c1 ("eeprom: at24: add support for at24mac series")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
There's an ilog2() expansion in AT24_DEVICE_MAGIC() which rounds down
the actual size of EUI-48 byte array in at24mac402 eeproms to 4 from 6,
making it impossible to read it all.
Fix it by manually adjusting the value in probe().
This patch contains a temporary fix that is suitable for stable
branches. Eventually we'll probably remove the call to ilog2() while
converting the magic values to actual structs.
Cc: stable@vger.kernel.org
Fixes: 0b813658c1 ("eeprom: at24: add support for at24mac series")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
