Consider following sequence of events:
1. UFS is runtime suspended, link_state = Hibern8, device_state = sleep
2. System goes into system suspend, ufshcd_system_suspend() brings both
link and device to active state and then puts the device in Power_Down
state and link in OFF state.
3. System resumes at some later point in time, ufshcd_system_resume()
doesn't do anything as UFS state is runtime suspended. Note that link
is still on OFF state and device is in Power_Down state.
4. Now system again goes into suspend without any UFS accesses before it.
ufshcd_system_suspend() again brings both link and device to active
state and then puts the device in Power_Down state and link if OFF
state. But it's unnecessary to bring the link & device in active state
as both link and device are already in desired low power states. This
change fixes this issue by adding proper state checks in
ufshcd_system_suspend().
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The condition in which error message is printed out was incorrect and
resulted error message only if retries exhausted.
But retries happens only if DME command is a peer command, and thus
DME commands which are not peer commands and fail are not printed out.
This change fixes this issue.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PHY_ADAPTER_ERROR status register indicates PHY lane errors
reported by the M-PHY layer. In some occasions the controller
can recover from such errors. When the error is not recoverable,
a stuck DB error will occur. Since the stuck DB error is spotted
separately, no action other than clearing the register is necessary.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we issue the link startup to the device while its UniPro state is
LinkDown (and device state is sleep/power-down) then link startup
will not move the device state to Active. Device will only move to
active state if the link starup is issued when its UniPro state is
LinkUp. So in this case, we would have to issue the link startup 2
times to make sure that device moves to active state.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices require host PA_TACTIVATE to be higher than
device PA_TACTIVATE otherwise it may get stuck during hibern8 sequence.
This change allows this by using quirk.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is found thats UFS device may take longer than 30ms to respond to
query requests and in this case we might run into following scenario:
1. UFS host SW sends a query request to UFS device to read an attribute
value. SW uses tag #31 for this purpose.
2. UFS host SW waits for 30ms to get the query response (and doorbell
to be cleared by UFS host HW).
3. UFS device doesn't respond back within 30ms hence UFS host SW times
out waiting for the query response.
4. UFS host SW clears the tag#31 from UTRLCLR register.
5. UFS host SW waits until UFS host HW to clear tag#31 from the doorbell
register.
6. UFS host SW retries the same query request on same tag#31 (sends a query
request to device to read an attribute value).
7. UFS host HW gets the query response from the device but this was
intended as a query response for the 1st query request sent (step-1).
8. Now UFS device sends another query response to host (for query request
sent @step-6).
Now there are 2 issues that could happen with above scenario:
1. UFS device should have actually responded back with only one query
response but it is found that device may respond back with 2 query
responses.
2. If UFS device responds back with 2 resposes on same tag, host HW/SW
behaviour isn't predictable.
To avoid running into above scenario, we would basically allow device
to take longer (upto 1.5 seconds) for query response.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reading variable size descriptors (like string descriptor), some UFS
devices may report the "LENGTH" (field in "Transaction Specific fields" of
Query Response UPIU) same as what was requested in Query Request UPIU
instead of reporting the actual size of the variable size descriptor.
Although it's safe to ignore the "LENGTH" field for variable size
descriptors as we can always derive the length of the descriptor from
the descriptor header fields. Hence this change impose the length match
check only for fixed size descriptors (for which we always request the
correct size as part of Query Request UPIU).
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to JESD220B - UFS v2.0, the maximum size of device descriptor
has changed from 0x1F to 0x40. This patch updates the maximum size of
this descriptor.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sending query to the device, the index of the failure
is additional useful information that should be printed out as it
might specify the logical unit (LU) where the error occurred.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of the queries might fail during init. To avoid
system failure, we add retry mechanism to issue queries
several times.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most error branches following the call to kzalloc contain a call to
kfree. This patch add these calls where they are missing.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most error branches following the call to pci_map_biosrom contain a call
to pci_unmap_biosrom. This patch add these calls where they are missing.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I'm getting a new warning with gcc-7:
isci/remote_node_context.c: In function 'sci_remote_node_context_destruct':
isci/remote_node_context.c:69:16: error: array subscript is above array bounds [-Werror=array-bounds]
This is odd, since we clearly cover all values for enum
scis_sds_remote_node_context_states here. Anyway, checking for an array
overflow can't harm and it makes the warning go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some typos where we intended "<<" but have "<". Seems likely
to cause a bunch of problems.
Fixes: d3b688d3c6 ("scsi: hisi_sas: add v2 hw support for ECC and AXI bus fatal error")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most error branches following the call to kzalloc contain a call to
kfree. This patch add these calls where they are missing and set the
relevant pointers to NULL.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a sysfs attribute 'ctlr_num' holding the current HPSA controller
number. This is required to construct compability 'cciss' links.
[mkp: fixed typo]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NOT_READY is a sense key, not a legit scsi hostbyte value. Use
DID_NO_CONNECT instead.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Additionally, rename srp_wait_for_queuecommand() into
scsi_wait_for_queuecommand() and add a comment about the queuecommand()
call from scsi_send_eh_cmnd().
Note: this patch changes scsi_internal_device_block from a function that
did not sleep into a function that may sleep. This is fine for all
callers of this function:
* scsi_internal_device_block() is called from the mpt3sas device while
that driver holds the ioc->dm_cmds.mutex. This means that the mpt3sas
driver calls this function from thread context.
* scsi_target_block() is called by __iscsi_block_session() from
kernel thread context and with IRQs enabled.
* The SRP transport code also calls scsi_target_block() from kernel
thread context while sleeping is allowed.
* The snic driver also calls scsi_target_block() from a context from
which sleeping is allowed. The scsi_target_block() call namely occurs
immediately after a scsi_flush_work() call.
[mkp: s/shost/sdev/]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Ledford <dledford@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We verified that resp_code is FC_SPP_RESP_ACK earlier so we don't need
to check again here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the function to set PHY min and max linkrate through
sysfs interface.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes the value of hisi_sas_device.running_req
would go negative unless we have the check for
running_req >= 0 before trying to decrement.
This is because using running_req is not thread-safe.
As such, the value for running_req may be actually incorrect,
so use atomic64_t instead.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check ERR bit of status to decide whether there is something wrong with
initial register-D2H FIS. If error exists, PHY reset the channel to
restart OOB.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify and add some SATA commands according to SATA protocol.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Delete repeated configuration items for hisi_sas_device() when
we free a device. These items are now only set in
hisi_sas_dev_gone().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_scsi_find_task() only deals with return value
TMF_RESP_FUNC_FAILED/TMF_RESP_FUNC_SUCC/TMF_RESP_FUNC_COMPLETE of
query task. So for LLDD errors just return TMF_RESP_FUNC_FAILED.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we form a wideport, we should use hardware PHY port_id instead
of sas_phy->id.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are many BROADCAST primitives generated by the host.
We are only interested in BROADCAST (CHANGE) primitives currently,
so only process this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently slots are allocated from queues in a round-robin fashion.
This causes a problem for internal commands in device mode. For this
mode, we should ensure that the internal abort command is the last
command seen in the host for that device. We can only ensure this when
we place the internal abort command after the preceding commands for
device that in the same queue, as there is no order in which the host
will select a queue to execute the next command.
This queue restriction makes supporting scsi mq more tricky in
the future, but should not be a blocker.
Note: Even though v1 hw does not support internal abort, the
allocation method is chosen to be the same for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ECC 1bit error, logic can recover it, so we only print
a warning.
For ECC multi-bit and AXI bus fatal error, we panic.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most error branches following the call to pmcraid_get_free_cmd contain a
call to pmcraid_return_cmd. This patch add these calls where they are
missing.
Moreover, most error branches following the call to class_create contain
a call to class_destroy. This patch add these calls where they are
missing.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controllers may think granularities of PRDT length and
offset as bytes, not double words.
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufs_qcom_init() sets the hba priv data before attempting to acquire the
phy handle, so make sure to clear this in the case of an error. Failing
to do this will make ufs_qcom_setup_clocks() operate on the uninitalized
host object.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These two macros cause lots of warnings with gcc-7:
drivers/scsi/bfa/bfa_svc.c: In function 'bfa_fcxp_meminfo':
drivers/scsi/bfa/bfa_svc.c:521:103: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
Using inline functions makes them much more readable and avoids the
warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use pci_alloc_irq_vectors and drop the hand-crafted interrupt affinity
routines.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Reviewed-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that all conversions are done, move the FibreChannel bsg code over
to the bsg library.
This patch is derived from work done by Mike Christie in 2011 [1] but
only the iscsi parts got merged back then.
[1] http://marc.info/?l=linux-scsi&m=131149780921009&w=2
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add bsg_job_put() and bsg_job_get() so don't need to export
bsg_destroy_job() any more.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_bsg_jobdone() and bsg_job_done() are 1:1 copies now so use the
bsg-lib one instead of the FC private implementation.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bsg_softirq_done() and fc_bsg_softirq_done() are copies of each other, so
ditch the fc specific one.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_destroy_bsgjob() and bsg_destroy_job() are now 1:1 copies, so use the
latter. As bsg_destroy_job() comes from bsg-lib we need to select it in
Kconfig once CONFOG_SCSI_FC_ATTRS is active.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of
'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct
fc_bsg_job'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement kref backed reference counting instead of rolling our own. This
elimnates the need of the following fields in 'struct fc_bsg_job':
* ref_cnt
* state_flags
* job_lock
bringing us close to unification of 'struct fc_bsg_job' and 'struct bsg_job'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't set FC_RQST_STATE_DONE before calling fc_bsg_jobdone() as
fc_bsg_jobdone() calls blk_complete_requeust() which raises a soft-IRQ
that ends up in fc_bsg_sofirq_done() and fc_bsg_softirq_done() sets the
FC_RQST_STATE_DONE flag.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide fc_bsg_to_rport() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also move all
LLDDs to use the new helper.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide fc_bsg_to_shost() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also use this
little helper in the LLDDs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export fc_bsg_jobdone so drivers can use it directly instead of doing
the round-trip via struct fc_bsg_job::job_done() and use it in the
LLDDs. That way we can also unify the interfaces of fc_bsg_jobdone and
bsg_job_done.
As we've converted all LLDDs over to use fc_bsg_jobdone() directly, we
can remove the function pointer from struct fc_bsg_job as well.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't use fc_bsg_job::request and fc_bsg_job::reply directly, but use
helper variables bsg_request and bsg_reply. This will be helpful when
transitioning to bsg-lib.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct fc_bsg_buffer is just a clone of struct bsg_buffer from bsg-lib,
so use this one instead.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:
drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.
Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.
Fixes: a4632aae8b ("[SCSI] mvsas: Add new macros and functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
