Return codes of IPA_CMD_QIPASSIST are not checked, especially the ones which
indicate that the command is not supported. As a result, the device driver
would not enable all available features on older card generations.
This patch adds proper checking and sets the bare minimum in the supported
functions flags to avoid follow-on errors.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device datasheet specifies the BUSY bit must be set when reading
or writing phy registers. This patch ensures we do that.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 73d4066055.
Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled. Thomas pointed out that this patch
is incorrect, and can cause problems. So revert it to get the
previously working functionality back.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f79b2d0f (USB: keyspan: fix NULL-pointer dereferences and
memory leaks) had a small typo which made the driver use wrong
offsets when mapping serial port private data. This results in
in a GPF when the port is opened.
Reported-by: Richard <richjunk@pacbell.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CBUS UART's interrupt number was wrong conflicting with the interrupt
being tied to the Intel PIIX4. Since the PIIX4's interrupt is registered
before the CBUS UART which is not being used on most systems this would
not be noticed.
Attempts to open the ttyS2 CBUS UART would result in:
genirq: Flags mismatch irq 18. 00000000 (serial) vs. 00010000 (XT-PIC cascade)
serial_link_irq_chain: request failed: -16 for irq: 18
Qemu was written to match the kernel so will need to be fixed also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are laptops out there that need the eDP bpc from VBT. This is
effectively a revert of
commit 4344b813f1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Aug 10 11:10:20 2012 +0200
drm/i915: ignore eDP bpc settings from vbt
but putting the VBT check after the EDID check to see them both in dmesg if
this clamps more than the EDID. We have enough history with bpc clamping to
warrant the extra debug info.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47641
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56401
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Select HAVE_ALIGNED_STRUCT_PAGE on s390, so that the slub allocator can make
use of compare and swap double for lockless updates. This increases the size
of struct page to 64 bytes (instead of 56 bytes), however the performance gain
justifies the increased size:
- now excactly four struct pages fit into a single cache line; the
case that accessing a struct page causes two cache line loads
does not exist anymore.
- calculating the offset of a struct page within the memmap array
is only a simple shift instead of a more expensive multiplication.
A "hackbench 200 process 200" run on a 32 cpu system did show an 8% runtime
improvement.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
access_ok() returns always "true" on s390. Therefore all access_ok()
invocations are rather pointless.
However when walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
So remove the access_ok() call and add the same check we have in
get_user_pages_fast().
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
Otherwise we might calculate e.g. a pud pointer which is not
within a pud and dereference it.
So check against TASK_SIZE (which is the ASCE limit) before
walking page tables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I don't think this works as intended. '|' higher precedence than ?: so
the bitwize OR "0 | (val & STR_MOST)" is a no-op.
I have re-written it to be more clear.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes plus a large but simple change for WM5102 which writes
out a bunch of register updates to the device when we enable the clock
as recommended following chip evaluation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3xEm
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
A few small fixes plus a large but simple change for WM5102 which writes
out a bunch of register updates to the device when we enable the clock
as recommended following chip evaluation.
Pull KVM fix from Marcelo Tosatti:
"A correction for user triggerable oops"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: invalid opcode oops on SET_SREGS with OSXSAVE bit set (CVE-2012-4461)
This pull request contains those missing clkdev entries which are needed
to boot that platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VC2a
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull ux500 clk fixes from Mike Turquette:
"Missing clkdev entries are causing regressions on the U8500 platform.
This pull request contains those missing clkdev entries which are
needed to boot that platform."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: ux500: Register slimbus clock lookups for u8500
clk: ux500: Update rtc clock lookup for u8500
clk: ux500: Register msp clock lookups for u8500
clk: ux500: Register ssp clock lookups for u8500
clk: ux500: Register i2c clock lookups for u8500
Pull menuconfig portability fix from Michal Marek:
"Here is a fix for v3.7 that makes menuconfig compile again on systems
whose C library is lacking CIRCLEQ_* macros. I thought I sent it
earlier, but apparently I did not."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
menuconfig: Replace CIRCLEQ by list_head-style lists.
Pull LED fix from Bryan Wu.
* 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ledtrig-cpu: kill useless mutex to fix sleep in atomic context
Pull futex fix from Thomas Gleixner:
"Single fix for a long standing futex race when taking over a futex
whose owner died. You can end up with two owners, which violates
quite some rules."
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Handle futex_pi OWNER_DIED take over correctly
On hosts without the XSAVE support unprivileged local user can trigger
oops similar to the one below by setting X86_CR4_OSXSAVE bit in guest
cr4 register using KVM_SET_SREGS ioctl and later issuing KVM_RUN
ioctl.
invalid opcode: 0000 [#2] SMP
Modules linked in: tun ip6table_filter ip6_tables ebtable_nat ebtables
...
Pid: 24935, comm: zoog_kvm_monito Tainted: G D 3.2.0-3-686-pae
EIP: 0060:[<f8b9550c>] EFLAGS: 00210246 CPU: 0
EIP is at kvm_arch_vcpu_ioctl_run+0x92a/0xd13 [kvm]
EAX: 00000001 EBX: 000f387e ECX: 00000000 EDX: 00000000
ESI: 00000000 EDI: 00000000 EBP: ef5a0060 ESP: d7c63e70
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process zoog_kvm_monito (pid: 24935, ti=d7c62000 task=ed84a0c0
task.ti=d7c62000)
Stack:
00000001 f70a1200 f8b940a9 ef5a0060 00000000 00200202 f8769009 00000000
ef5a0060 000f387e eda5c020 8722f9c8 00015bae 00000000 ed84a0c0 ed84a0c0
c12bf02d 0000ae80 ef7f8740 fffffffb f359b740 ef5a0060 f8b85dc1 0000ae80
Call Trace:
[<f8b940a9>] ? kvm_arch_vcpu_ioctl_set_sregs+0x2fe/0x308 [kvm]
...
[<c12bfb44>] ? syscall_call+0x7/0xb
Code: 89 e8 e8 14 ee ff ff ba 00 00 04 00 89 e8 e8 98 48 ff ff 85 c0 74
1e 83 7d 48 00 75 18 8b 85 08 07 00 00 31 c9 8b 95 0c 07 00 00 <0f> 01
d1 c7 45 48 01 00 00 00 c7 45 1c 01 00 00 00 0f ae f0 89
EIP: [<f8b9550c>] kvm_arch_vcpu_ioctl_run+0x92a/0xd13 [kvm] SS:ESP
0068:d7c63e70
QEMU first retrieves the supported features via KVM_GET_SUPPORTED_CPUID
and then sets them later. So guest's X86_FEATURE_XSAVE should be masked
out on hosts without X86_FEATURE_XSAVE, making kvm_set_cr4 with
X86_CR4_OSXSAVE fail. Userspaces that allow specifying guest cpuid with
X86_FEATURE_XSAVE even on hosts that do not support it, might be
susceptible to this attack from inside the guest as well.
Allow setting X86_CR4_OSXSAVE bit only if host has XSAVE support.
Signed-off-by: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Since commit edc88ceb0 (ARM: be really quiet when building with 'make -s') the
following output is generated when building a kernel for ARM:
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
Building modules, stage 2.
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
As per Documentation/kbuild/makefiles.txt the correct way of using kecho is
'@$(kecho)'.
Make this change so no more unwanted 'echo' messages are displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kevin Hilman and Paul Walmsley.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pyxl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Minor OMAP PM and hwmod fixes for v3.7-rc series via
Kevin Hilman and Paul Walmsley.
* tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: OMAP2+: PM: add missing newline to VC warning message
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Any failures in intel_sdvo_init() after the intel_sdvo_setup_output() call
left behind ghost connectors, attached (with a dangling pointer) to the
sdvo that has been cleaned up and freed. Properly destroy any connectors
attached to the encoder.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46381
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Tested-by: bjo@nord-west.org
[danvet: added a comment to explain why we need to clean up connectors
even when sdvo_output_setup fails.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the same time the prcc bit for the kclk is corrected to
bit 8 instead of 3.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
on omap4 again. Although it's getting rather late for these
changes for the -rc cycle, it is important as many devices
are using MUSB for charging and connectivity.
With the USB PHY changes, MUSB started using the newly added
drivers/usb/phy/omap-usb2.c driver introduced by commit
657b306a (usb: phy: add a new driver for omap usb2 phy)
that is using the newly introduced drivers/bus/omap-ocp2scp.c
introduced by commit 26a84b3e (drivers: bus: add a new driver
for omap-ocp2scp).
These changes allowed dropping a lot of PHY related code from
arch/arm/mach-omap2/omap_phy_internal.c and have it live in
the device driver like it should with commit c9e4412a (arm: omap:
phy: remove unused functions from omap-phy-internal.c).
However, MUSB on omap4 broke with these changes for legacy
platform data boot, and now only works with device tree for
omap4. Unfortunately we are still few critical bindings away
from being able to make omap4 usbale with device tree.
Fix the regression properly by adding platform data support
to the ocp2scp driver so we can avoid adding back the driver
code to arch/arm/mach-omap2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQmqakAAoJEBvUPslcq6VzBjcQANthvtvNsUrR3X3lB5GRwtIJ
uGcOVqdrI9Y6seHQMqCiwa9JNlBHu+ABLYV4UGSNtHLAlaI+pilaqby7cUndFmBo
O7FMPAK6EmrUqXewkQh3W3yx/JEy4zu7Kup5rK8p9kPBmqblrjdtfmlrIKjBBhbA
4ZBQC82GSDg/UtLcVxjXgb2aJnLim5L2WU1drCSHgclyBWueg8ijFsTl9l7R9Zwh
x6FV6DYHZyxFzvuXlB+83iZ1sJ6qpkD92hPe+Lj3jyxpW6+b6Mx5d/268743+Nde
xzCxQ09JGYN+h/N+QX6SRhurHjlXGFwmAhYofdO+r7OdLrT12VHiOptRKh0N9DfX
s1Mtk+X6f5iwKo8O//5DXkZPDLW8fI1GNs6QNsw71yM1mDP7tCamYUsSpLLJLcYo
bB/O77HdQDWAWBOwbu+GY4eICTgh/Chj3LYe0Aic8F1jm8kzQm5CJMgxyAeMUrHX
2O0yGUUIIqWkNdn/iluVHVs0nHwjfDZsRN4cAdMbjkqF4cJRkH2lIjrSSYlJxYmL
cymFrkR0Evj2fmGXhEcX8pGgymlSp1Aj1tnaQ6I06XEjrlbtRpAsibniSx4OCcB2
3sMZOpvmUYD/FecaZRatoOLQC6aNMY8ape0ghLFAklz1By7c2ytzGRQsoDqMoXql
hl44QO9QKIYBYb2pPcDj
=bbq5
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc4/musb-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
This series fixes an annoying regression to make MUSB working
on omap4 again. Although it's getting rather late for these
changes for the -rc cycle, it is important as many devices
are using MUSB for charging and connectivity.
With the USB PHY changes, MUSB started using the newly added
drivers/usb/phy/omap-usb2.c driver introduced by commit
657b306a (usb: phy: add a new driver for omap usb2 phy)
that is using the newly introduced drivers/bus/omap-ocp2scp.c
introduced by commit 26a84b3e (drivers: bus: add a new driver
for omap-ocp2scp).
These changes allowed dropping a lot of PHY related code from
arch/arm/mach-omap2/omap_phy_internal.c and have it live in
the device driver like it should with commit c9e4412a (arm: omap:
phy: remove unused functions from omap-phy-internal.c).
However, MUSB on omap4 broke with these changes for legacy
platform data boot, and now only works with device tree for
omap4. Unfortunately we are still few critical bindings away
from being able to make omap4 usbale with device tree.
Fix the regression properly by adding platform data support
to the ocp2scp driver so we can avoid adding back the driver
code to arch/arm/mach-omap2.
* tag 'omap-for-v3.7-rc4/musb-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: ocp2scp: create omap device for ocp2scp
ARM: OMAP4: add _dev_attr_ to ocp2scp for representing usb_phy
drivers: bus: ocp2scp: add pdata support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When in world roaming mode, allow 40 MHz to be used
on channels 12 and 13 so that an AP that is, e.g.,
using HT40+ on channel 9 (in the UK) can be used.
Cc: stable@vger.kernel.org
Reported-by: Eddie Chapman <eddie@ehuk.net>
Tested-by: Eddie Chapman <eddie@ehuk.net>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current topology code confuses core id vs physical package id.
In other words /sys/devices/system/cpu/cpuX/topology/core_id
displays the physical_package_id (aka socket id) instead of the
core id.
The physical_package_id sysfs attribute always displays "-1"
instead of the socket id.
Fix this mix-up with a small patch which defines and initializes
topology_physical_package_id correctly and fixes the broken
core id handling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If user space is running in primary mode it can switch to secondary
or access register mode, this is used e.g. in the clock_gettime code
of the vdso. If a signal is delivered to the user space process while
it has been running in access register mode the signal handler is
executed in access register mode as well which will result in a crash
most of the time.
Set the address space control bits in the PSW to the default for the
execution of the signal handler and make sure that the previous
address space control is restored on signal return. Take care
that user space can not switch to the kernel address space by
modifying the registers in the signal frame.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In patch "HID: microsoft: fix invalid rdesc for 3k kbd" I fixed
support for MS 3k keyboards. However the added check using memcmp and
a compound statement breaks build on architectures where memcmp is a
macro with parameters.
hid-microsoft.c:51:18: error: macro "memcmp" passed 6 arguments, but takes just 3
On x86_64, memcmp is a function, so I did not see the error.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is another variant of iMac 9,1 with a different codec SSID.
Reported-and-tested-by: Everaldo Canuto <everaldo.canuto@gmail.com>
Cc: <stable@vger.kernel.org> [v3.3+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(1<<optname) is undefined behavior in C with a negative optname or
optname larger than 31. In those cases the result of the shift is
not necessarily zero (e.g., on x86).
This patch simplifies the code with a switch statement on optname.
It also allows the compiler to generate better code (e.g., using a
64-bit mask).
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seeing the following every time the CPU enters or leaves idle on a
Beagleboard:
BUG: sleeping function called from invalid context at kernel/mutex.c:269
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
no locks held by swapper/0/0.
[<c001659c>] (unwind_backtrace+0x0/0xf8) from [<c05aaa7c>] (mutex_lock_nested+0x24/0x380)
[<c05aaa7c>] (mutex_lock_nested+0x24/0x380) from [<c043bd1c>] (ledtrig_cpu+0x38/0x88)
[<c043bd1c>] (ledtrig_cpu+0x38/0x88) from [<c000f4b0>] (cpu_idle+0xf4/0x120)
[<c000f4b0>] (cpu_idle+0xf4/0x120) from [<c07e47c8>] (start_kernel+0x2bc/0x30c)
Miles Lane has reported seeing similar splats during system suspend.
The mutex in struct led_trigger_cpu appears to have no function: it
resides in a per-cpu data structure which never changes after the
trigger is registered. So just remove it.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Bryan Wu <roc@roc-samos.(none)>
Pull networking fixes from David Miller:
"Bug fixes galore, mostly in drivers as is often the case:
1) USB gadget and cdc_eem drivers need adjustments to their frame size
lengths in order to handle VLANs correctly. From Ian Coolidge.
2) TIPC and several network drivers erroneously call tasklet_disable
before tasklet_kill, fix from Xiaotian Feng.
3) r8169 driver needs to apply the WOL suspend quirk to more chipsets,
fix from Cyril Brulebois.
4) Fix multicast filters on RTL_GIGA_MAC_VER_35 r8169 chips, from
Nathan Walp.
5) FDB netlink dumps should use RTM_NEWNEIGH as the message type, not
zero. From John Fastabend.
6) Fix smsc95xx tx checksum offload on big-endian, from Steve
Glendinning.
7) __inet_diag_dump() needs to repsect and report the error value
returned from inet_diag_lock_handler() rather than ignore it.
Otherwise if an inet diag handler is not available for a particular
protocol, we essentially report success instead of giving an error
indication. Fix from Cyrill Gorcunov.
8) When the QFQ packet scheduler sees TSO/GSO packets it does not
handle things properly, and in fact ends up corrupting it's
datastructures as well as mis-schedule packets. Fix from Paolo
Valente.
9) Fix oopser in skb_loop_sk(), from Eric Leblond.
10) CXGB4 passes partially uninitialized datastructures in to FW
commands, fix from Vipul Pandya.
11) When we send unsolicited ipv6 neighbour advertisements, we should
send them to the link-local allnodes multicast address, as per
RFC4861. Fix from Hannes Frederic Sowa.
12) There is some kind of bug in the usbnet's kevent deferral
mechanism, but more immediately when it triggers an uncontrolled
stream of kernel messages spam the log. Rate limit the error log
message triggered when this problem occurs, as sending thousands
of error messages into the kernel log doesn't help matters at all,
and in fact makes further diagnosis more difficult.
From Steve Glendinning.
13) Fix gianfar restore from hibernation, from Wang Dongsheng.
14) The netlink message attribute sizes are wrong in the ipv6 GRE
driver, it was using the size of ipv4 addresses instead of ipv6
ones :-) Fix from Nicolas Dichtel."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
gre6: fix rtnl dump messages
gianfar: ethernet vanishes after restoring from hibernation
usbnet: ratelimit kevent may have been dropped warnings
ipv6: send unsolicited neighbour advertisements to all-nodes
net: usb: cdc_eem: Fix rx skb allocation for 802.1Q VLANs
usb: gadget: g_ether: fix frame size check for 802.1Q
cxgb4: Fix initialization of SGE_CONTROL register
isdn: Make CONFIG_ISDN depend on CONFIG_NETDEVICES
cxgb4: Initialize data structures before using.
af-packet: fix oops when socket is not present
pkt_sched: enable QFQ to support TSO/GSO
net: inet_diag -- Return error code if protocol handler is missed
net: bnx2x: Fix typo in bnx2x driver
smsc95xx: fix tx checksum offload for big endian
rtnetlink: Use nlmsg type RTM_NEWNEIGH from dflt fdb dump
ptp: update adjfreq callback description
r8169: allow multicast packets on sub-8168f chipset.
r8169: Fix WoL on RTL8168d/8111d.
drivers/net: use tasklet_kill in device remove/close process
tipc: do not use tasklet_disable before tasklet_kill
Pull sparc fixes from David Miller:
"Several build/bug fixes for sparc, including:
1) Configuring a mix of static vs. modular sparc64 crypto modules
didn't work, remove an ill-conceived attempt to only have to build
the device match table for these drivers once to fix the problem.
Reported by Meelis Roos.
2) Make the montgomery multiple/square and mpmul instructions actually
usable in 32-bit tasks. Essentially this involves providing 32-bit
userspace with a way to use a 64-bit stack when it needs to.
3) Our sparc64 atomic backoffs don't yield cpu strands properly on
Niagara chips. Use pause instruction when available to achieve
this, otherwise use a benign instruction we know blocks the strand
for some time.
4) Wire up kcmp
5) Fix the build of various drivers by removing the unnecessary
blocking of OF_GPIO when SPARC.
6) Fix unintended regression wherein of_address_to_resource stopped
being provided. Fix from Andreas Larsson.
7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
Larsson."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
sparc: Support atomic64_dec_if_positive properly.
of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
sparc: Add sparc support for platform_get_irq()
sparc: Allow OF_GPIO on sparc.
qlogicpti: Fix build warning.
sparc: Wire up sys_kcmp.
sparc64: Improvde documentation and readability of atomic backoff code.
sparc64: Use pause instruction when available.
sparc64: Fix cpu strand yielding.
sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.
Fixes more wifi status skb leaks, leading to hostapd/wpa_supplicant hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull cifs fixes from Jeff Layton.
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Do not lookup hashed negative dentry in cifs_atomic_open
cifs: fix potential buffer overrun in cifs.idmap handling code
- correct argument type (pgprot_t) when calling __ioremap()
- PCI_IOBASE virtual address change
- use architected event for CPU cycle counter
- fix ELF core dumping
- select CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION
- missing completion for secondary CPU boot
- booting on systems with all memory beyond 4GB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=g5mZ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- correct argument type (pgprot_t) when calling __ioremap()
- PCI_IOBASE virtual address change
- use architected event for CPU cycle counter
- fix ELF core dumping
- select CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION
- missing completion for secondary CPU boot
- booting on systems with all memory beyond 4GB
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: mm: fix booting on systems with no memory below 4GB
arm64: smp: add missing completion for secondary boot
arm64: compat: select CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION
arm64: elf: fix core dumping definitions for GP and FP registers
arm64: perf: use architected event for CPU cycle counter
arm64: Move PCI_IOBASE closer to MODULES_VADDR
arm64: Use pgprot_t as the last argument when invoking __ioremap()
* Fix compile issues on ARM.
* Fix hypercall fallback code for old hypervisors.
* Print out which HVM parameter failed if it fails.
* Fix idle notifier call after irq_enter.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQnQdGAAoJEFjIrFwIi8fJPBAIAMX1HRx3udqhv7fziynZvFTb
hj47XYIJHOK7P4fK7vZoSNgMHjL6LW5cUqC8VN67G3zUSkX9JYFsPBj6v4bWn+rG
b9CS+MW7hS80LGbbqkh1F+YSEfZ863RlF9PPX2acaHTw49MlIgIqwhxIo6hy+Nm6
thu6SlbEIJkSUdhbYMOAmy5aH/3+UuuQg+oq3P7mzV8fZjEihnrrF0NlT4wOZK1o
gsfrKYKJLVT526W9PF/L23/A/MCHMpvjNStpaDLOGNjV9sBMpJI8JRax6+657+q1
0kXvN5mAwTKWOaXBl4LEC9R8n1IKB91TgOY6HJAcXkb1eoP5KAeNSmU8RbsZ2T0=
=XZ+0
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"There are three ARM compile fixes (we forgot to export certain
functions and if the drivers are built as an module - we go belly-up).
There is also an mismatch of irq_enter() / exit_idle() calls sequence
which were fixed some time ago in other piece of codes, but failed to
appear in the Xen code.
Lastly a fix for to help in the field with troubleshooting in case we
cannot get the appropriate parameter and also fallback code when
working with very old hypervisors."
Bug-fixes:
- Fix compile issues on ARM.
- Fix hypercall fallback code for old hypervisors.
- Print out which HVM parameter failed if it fails.
- Fix idle notifier call after irq_enter.
* tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/arm: Fix compile errors when drivers are compiled as modules (export more).
xen/arm: Fix compile errors when drivers are compiled as modules.
xen/generic: Disable fallback build on ARM.
xen/events: fix RCU warning, or Call idle notifier after irq_enter()
xen/hvm: If we fail to fetch an HVM parameter print out which flag it is.
xen/hypercall: fix hypercall fallback code for very old hypervisors
We tried linking in a single built object to hold the device table,
but only works if all of the sparc64 crypto modules get built the same
way (modular vs. non-modular).
Just include the device ID stub into each driver source file so that
the table gets compiled into the correct result in all cases.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparc32 already supported it, as a consequence of using the
generic atomic64 implementation. And the sparc64 implementation
is rather trivial.
This allows us to set ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE for all
of sparc, and avoid the annoying warning from lib/atomic64_test.c
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug-fix makes sure that of_address_to_resource is defined extern for sparc
so that the sparc-specific implementation of of_address_to_resource() is once
again used when including include/linux/of_address.h in a sparc context. A
number of drivers in mainline relies on this function working for sparc.
The bug was introduced in a850a75544, "of/address:
add empty static inlines for !CONFIG_OF". Contrary to that commit title, the
static inlines are added for !CONFIG_OF_ADDRESS, and CONFIG_OF_ADDRESS is never
defined for sparc. This is good behavior for the other functions in
include/linux/of_address.h, as the extern functions defined in
drivers/of/address.c only gets linked when OF_ADDRESS is configured. However,
for of_address_to_resource there exists a sparc-specific implementation in
arch/sparc/arch/sparc/kernel/of_device_common.c
Solution suggested by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an irq is being unlinked concurrently with leon_handle_ext_irq,
irq_map[eirq] might be null in leon_handle_ext_irq. Make sure that
this is not dereferenced.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds sparc support for platform_get_irq that in the normal case use
platform_get_resource() to get an irq. This standard approach fails for sparc as
there are no resources of type IORESOURCE_IRQ for irqs for sparc.
Cross platform drivers can then use this standard platform function and work on
sparc instead of having to have a special case for sparc.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spotted after a code review.
Introduced by c12b395a46 (gre: Support GRE over
IPv6).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.
For example:
~# ifconfig eth0 down
~# echo disk > /sys/power/state
<trigger a restore from hibernation>
~# ifconfig eth0 up
SIOCSIFFLAGS: No such device
This happens because the restore function bails out early upon
finding devices that were not up at hibernation. In doing so,
it never gets to the netif_device_attach call at the end of
the restore function. Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
