The memcg uncharging code that is involved towards the end of a page's
lifetime - truncation, reclaim, swapout, migration - is impressively
complicated and fragile.
Because anonymous and file pages were always charged before they had their
page->mapping established, uncharges had to happen when the page type
could still be known from the context; as in unmap for anonymous, page
cache removal for file and shmem pages, and swap cache truncation for swap
pages. However, these operations happen well before the page is actually
freed, and so a lot of synchronization is necessary:
- Charging, uncharging, page migration, and charge migration all need
to take a per-page bit spinlock as they could race with uncharging.
- Swap cache truncation happens during both swap-in and swap-out, and
possibly repeatedly before the page is actually freed. This means
that the memcg swapout code is called from many contexts that make
no sense and it has to figure out the direction from page state to
make sure memory and memory+swap are always correctly charged.
- On page migration, the old page might be unmapped but then reused,
so memcg code has to prevent untimely uncharging in that case.
Because this code - which should be a simple charge transfer - is so
special-cased, it is not reusable for replace_page_cache().
But now that charged pages always have a page->mapping, introduce
mem_cgroup_uncharge(), which is called after the final put_page(), when we
know for sure that nobody is looking at the page anymore.
For page migration, introduce mem_cgroup_migrate(), which is called after
the migration is successful and the new page is fully rmapped. Because
the old page is no longer uncharged after migration, prevent double
charges by decoupling the page's memcg association (PCG_USED and
pc->mem_cgroup) from the page holding an actual charge. The new bits
PCG_MEM and PCG_MEMSW represent the respective charges and are transferred
to the new page during migration.
mem_cgroup_migrate() is suitable for replace_page_cache() as well,
which gets rid of mem_cgroup_replace_page_cache(). However, care
needs to be taken because both the source and the target page can
already be charged and on the LRU when fuse is splicing: grab the page
lock on the charge moving side to prevent changing pc->mem_cgroup of a
page under migration. Also, the lruvecs of both pages change as we
uncharge the old and charge the new during migration, and putback may
race with us, so grab the lru lock and isolate the pages iff on LRU to
prevent races and ensure the pages are on the right lruvec afterward.
Swap accounting is massively simplified: because the page is no longer
uncharged as early as swap cache deletion, a new mem_cgroup_swapout() can
transfer the page's memory+swap charge (PCG_MEMSW) to the swap entry
before the final put_page() in page reclaim.
Finally, page_cgroup changes are now protected by whatever protection the
page itself offers: anonymous pages are charged under the page table lock,
whereas page cache insertions, swapin, and migration hold the page lock.
Uncharging happens under full exclusion with no outstanding references.
Charging and uncharging also ensure that the page is off-LRU, which
serializes against charge migration. Remove the very costly page_cgroup
lock and set pc->flags non-atomically.
[mhocko@suse.cz: mem_cgroup_charge_statistics needs preempt_disable]
[vdavydov@parallels.com: fix flags definition]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These patches rework memcg charge lifetime to integrate more naturally
with the lifetime of user pages. This drastically simplifies the code and
reduces charging and uncharging overhead. The most expensive part of
charging and uncharging is the page_cgroup bit spinlock, which is removed
entirely after this series.
Here are the top-10 profile entries of a stress test that reads a 128G
sparse file on a freshly booted box, without even a dedicated cgroup (i.e.
executing in the root memcg). Before:
15.36% cat [kernel.kallsyms] [k] copy_user_generic_string
13.31% cat [kernel.kallsyms] [k] memset
11.48% cat [kernel.kallsyms] [k] do_mpage_readpage
4.23% cat [kernel.kallsyms] [k] get_page_from_freelist
2.38% cat [kernel.kallsyms] [k] put_page
2.32% cat [kernel.kallsyms] [k] __mem_cgroup_commit_charge
2.18% kswapd0 [kernel.kallsyms] [k] __mem_cgroup_uncharge_common
1.92% kswapd0 [kernel.kallsyms] [k] shrink_page_list
1.86% cat [kernel.kallsyms] [k] __radix_tree_lookup
1.62% cat [kernel.kallsyms] [k] __pagevec_lru_add_fn
After:
15.67% cat [kernel.kallsyms] [k] copy_user_generic_string
13.48% cat [kernel.kallsyms] [k] memset
11.42% cat [kernel.kallsyms] [k] do_mpage_readpage
3.98% cat [kernel.kallsyms] [k] get_page_from_freelist
2.46% cat [kernel.kallsyms] [k] put_page
2.13% kswapd0 [kernel.kallsyms] [k] shrink_page_list
1.88% cat [kernel.kallsyms] [k] __radix_tree_lookup
1.67% cat [kernel.kallsyms] [k] __pagevec_lru_add_fn
1.39% kswapd0 [kernel.kallsyms] [k] free_pcppages_bulk
1.30% cat [kernel.kallsyms] [k] kfree
As you can see, the memcg footprint has shrunk quite a bit.
text data bss dec hex filename
37970 9892 400 48262 bc86 mm/memcontrol.o.old
35239 9892 400 45531 b1db mm/memcontrol.o
This patch (of 4):
The memcg charge API charges pages before they are rmapped - i.e. have an
actual "type" - and so every callsite needs its own set of charge and
uncharge functions to know what type is being operated on. Worse,
uncharge has to happen from a context that is still type-specific, rather
than at the end of the page's lifetime with exclusive access, and so
requires a lot of synchronization.
Rewrite the charge API to provide a generic set of try_charge(),
commit_charge() and cancel_charge() transaction operations, much like
what's currently done for swap-in:
mem_cgroup_try_charge() attempts to reserve a charge, reclaiming
pages from the memcg if necessary.
mem_cgroup_commit_charge() commits the page to the charge once it
has a valid page->mapping and PageAnon() reliably tells the type.
mem_cgroup_cancel_charge() aborts the transaction.
This reduces the charge API and enables subsequent patches to
drastically simplify uncharging.
As pages need to be committed after rmap is established but before they
are added to the LRU, page_add_new_anon_rmap() must stop doing LRU
additions again. Revive lru_cache_add_active_or_unevictable().
[hughd@google.com: fix shmem_unuse]
[hughd@google.com: Add comments on the private use of -EAGAIN]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
Pull networking fixes from David Miller:
"This fixes the most immediate fallout from yesterday's networking
merge:
1) sock_tx_timestamp() must not clear the passed in tx_flags, but
rather add to them. Fix from Eric Dumazet.
2) The hyperv driver sendbuf region increase needs to be decreased
slightly to handle older backends. From KY Srinivasan.
3) Fix RCU lockdep splats in netlink diag after recent hashing
changes, from Thomas Graf.
4) The new IPV6_FLOWLABEL was given a socket option number that
overlapped with an existing IP6 tables one, breaking ip6_tables.
Fixed by Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netlink: hold nl_sock_hash_lock during diag dump
tcp: md5: check md5 signature without socket lock
net: fix USB network driver config option.
net: reallocate new socket option number for IPV6_AUTOFLOWLABEL
vmxnet3: fix decimal printf format specifiers prefixed with 0x
net-timestamp: cumulative tcp timestamping fixes
hyperv: Adjust the size of sendbuf region to support ws2008r2
cxgb4: Fix for SR-IOV VF initialization
net-timestamp: sock_tx_timestamp() fix
Pull HID updates from Jiri Kosina:
"Some highlights:
- hid-sony improvements of Sixaxis device support by Antonio Ospite
- hid-hyperv driven devices can now be used as wakeup source, by
Dexuan Cui
- hid-lenovo driver is now more generic and supports more devices, by
Jamie Lentin
- hid-huion now supports wider range of tablets, by Nikolai
Kondrashov
- other various unsorted fixes and device ID additions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
HID: hyperv: register as a wakeup source
HID: sony: Default initialize all elements of the LED max_brightness array to 1
HID: huion: Fix sparse warnings
HID: usbhid: Use flag HID_DISCONNECTED when a usb device is removed
HID: ignore jabra gn9350e
HID: cp2112: add I2C mode
HID: use multi input quirk for 22b9:2968
HID: rmi: only bind the hid-rmi driver to the mouse interface of composite USB devices
HID: rmi: check that report ids exist in the report_id_hash before accessing their size
HID: lenovo: Add support for Compact (BT|USB) keyboard
HID: lenovo: Don't call function in condition, show error codes
HID: lenovo: Prepare support for adding other devices
HID: lenovo: Rename hid-lenovo-tpkbd to hid-lenovo
HID: huion: Handle tablets with UC-Logic vendor ID
HID: huion: Switch to generating report descriptor
HID: huion: Don't ignore other interfaces
HID: huion: Use "tablet" instead of specific model
HID: add quirk for 0x04d9:0xa096 device
HID: i2c-hid: call the hid driver's suspend and resume callbacks
HID: rmi: change logging level of log messages related to unexpected reports
...
- ACPICA update to upstream version 20140724. That includes
ACPI 5.1 material (support for the _CCA and _DSD predefined names,
changes related to the DMAR and PCCT tables and ARM support among
other things) and cleanups related to using ACPICA's header files.
A major part of it is related to acpidump and the core code used
by that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and
Rafael J Wysocki.
- Cleanups and improvements related to system suspend from
Lan Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand
governor and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from
Mikulas Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano,
Sandeep Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ZODv
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Again, ACPICA leads the pack (47 commits), followed by cpufreq (18
commits) and system suspend/hibernation (9 commits).
From the new code perspective, the ACPICA update brings ACPI 5.1 to
the table, including a new device configuration object called _DSD
(Device Specific Data) that will hopefully help us to operate device
properties like Device Trees do (at least to some extent) and changes
related to supporting ACPI on ARM.
Apart from that we have hibernation changes making it use radix trees
to store memory bitmaps which should speed up some operations carried
out by it quite significantly. We also have some power management
changes related to suspend-to-idle (the "freeze" sleep state) support
and more preliminary changes needed to support ACPI on ARM (outside of
ACPICA).
The rest is fixes and cleanups pretty much everywhere.
Specifics:
- ACPICA update to upstream version 20140724. That includes ACPI 5.1
material (support for the _CCA and _DSD predefined names, changes
related to the DMAR and PCCT tables and ARM support among other
things) and cleanups related to using ACPICA's header files. A
major part of it is related to acpidump and the core code used by
that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and Rafael J
Wysocki.
- Cleanups and improvements related to system suspend from Lan
Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand governor
and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from Mikulas
Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano, Sandeep
Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas
Renninger"
* tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (118 commits)
ACPI / LPSS: add LPSS device for Wildcat Point PCH
ACPI / PNP: Replace faulty is_hex_digit() by isxdigit()
ACPICA: Update version to 20140724.
ACPICA: ACPI 5.1: Update for PCCT table changes.
ACPICA/ARM: ACPI 5.1: Update for GTDT table changes.
ACPICA/ARM: ACPI 5.1: Update for MADT changes.
ACPICA/ARM: ACPI 5.1: Update for FADT changes.
ACPICA: ACPI 5.1: Support for the _CCA predifined name.
ACPICA: ACPI 5.1: New notify value for System Affinity Update.
ACPICA: ACPI 5.1: Support for the _DSD predefined name.
ACPICA: Debug object: Add current value of Timer() to debug line prefix.
ACPICA: acpihelp: Add UUID support, restructure some existing files.
ACPICA: Utilities: Fix local printf issue.
ACPICA: Tables: Update for DMAR table changes.
ACPICA: Remove some extraneous printf arguments.
ACPICA: Update for comments/formatting. No functional changes.
ACPICA: Disassembler: Add support for the ToUUID opererator (macro).
ACPICA: Remove a redundant cast to acpi_size for ACPI_OFFSET() macro.
ACPICA: Work around an ancient GCC bug.
ACPI / processor: Make it possible to get local x2apic id via _MAT
...
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works. The only major change in ALSA core is the
addition of timestamp type in sw_params field. This should behave in
backward compatible way. Other than that, there are lots of small
changes and new drivers in wide range, including a large code cut in
HD-audio driver for deprecated static quirks. Some highlights are
below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks, Realtek
RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RL72
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works.
The only major change in ALSA core is the addition of timestamp type
in sw_params field. This should behave in backward compatible way.
Other than that, there are lots of small changes and new drivers in
wide range, including a large code cut in HD-audio driver for
deprecated static quirks. Some highlights are below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks,
Realtek RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers"
* tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (402 commits)
ALSA: usb-audio: Whitespace cleanups for sound/usb/midi.*
ALSA: usb-audio: Respond to suspend and resume callbacks for MIDI input
sound/oss/pss: Remove typedefs pss_mixerdata and pss_confdata
sound/oss/opl3: Remove typedef opl_devinfo
ALSA: fireworks: fix specifiers in format strings for propper output
ASoC: imx-audmux: Use uintptr_t for port numbers
ASoC: davinci: Enable menuconfig entry for McASP
ASoC: fsl_asrc: Don't access members of config before checking it
ASoC: fsl_sarc_dma: Check pair before using it
ASoC: adau1977: Fix truncation warning on 64 bit architectures
ALSA: virtuoso: add Xonar Essence STX II support
ALSA: riptide: fix %d confusingly prefixed with 0x in format strings
ALSA: fireworks: fix %d confusingly prefixed with 0x in format strings
ALSA: hda - add codec ID for Braswell display audio codec
ALSA: hda - add PCI IDs for Intel Braswell
ALSA: usb-audio: Adjust Gamecom 780 volume level
ALSA: usb-audio: improve dmesg source grepability
ASoC: rt5670: Fix duplicate const warnings
ASoC: rt5670: Staticise non-exported symbols
ASoC: Intel: update stream only on stream IPC msgs
...
Apparently, bitmap_andnot is supposed to return whether the new bitmap
is empty. But it didn't take potential garbage bits in the last word
into account.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apparently, bitmap_and is supposed to return whether the new bitmap is
empty. But it didn't take potential garbage bits in the last word into
account.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no guarantee that *src does not contain garbage bits outside
the lower nbits, so we need to mask it before the shift-and-assign.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changing the pos parameter of __reg_op to unsigned allows the compiler
to generate slightly smaller and simpler code. Also update its callers
bitmap_*_region to receive and pass unsigned int. The return types of
bitmap_find_free_region and bitmap_allocate_region are still int to
allow a negative error code to be returned. An int is certainly capable
of representing any realistic return value.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "start" is non-negative.
Also, use the names "start" and "len" for the two parameters for
consistency with bitmap_set.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "start" is non-negative.
Also, use the names "start" and "len" for the two parameters in both
header file and implementation, instead of the previous mix.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "nbits" is non-negative. Since no-one passes a negative
bit-count, this shouldn't affect the semantics.
I didn't change the return type, since that might change the semantics
of some expression containing a call to bitmap_weight(). Certainly an
int is capable of holding the result.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "nbits" is non-negative. Since no-one passes a negative
bit-count, this shouldn't affect the semantics.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "nbits" is non-negative. Since no-one passes a negative
bit-count, this shouldn't affect the semantics.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change is only for consistency with the changes to the other
bitmap_* functions; it doesn't change the size of the generated code:
inside BITS_TO_LONGS there is a sizeof(long), which causes bits to be
interpreted as unsigned anyway.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the extra bits are "don't care", there is no reason to mask the
last word to the used bits when complementing. This shaves off yet a
few bytes.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "nbits" is non-negative. Since no-one passes a negative
bit-count, this shouldn't affect the semantics.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "nbits" is non-negative. Since no-one passes a negative
bit-count, this shouldn't affect the semantics.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler can generate slightly smaller and simpler code when it
knows that "nbits" is non-negative. Since no-one passes a negative
bit-count, this shouldn't affect the semantics.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many functions in lib/bitmap.c start with an expression such as lim =
bits/BITS_PER_LONG. Since bits has type (signed) int, and since gcc
cannot know that it is in fact non-negative, it generates worse code
than it could. These patches, mostly consisting of changing various
parameters to unsigned, gives a slight overall code reduction:
add/remove: 1/1 grow/shrink: 8/16 up/down: 251/-414 (-163)
function old new delta
tick_device_uses_broadcast 335 425 +90
__irq_alloc_descs 498 554 +56
__bitmap_andnot 73 115 +42
__bitmap_and 70 101 +31
bitmap_weight - 11 +11
copy_hugetlb_page_range 752 762 +10
follow_hugetlb_page 846 854 +8
hugetlb_init 1415 1417 +2
hugetlb_nrpages_setup 130 131 +1
hugetlb_add_hstate 377 376 -1
bitmap_allocate_region 82 80 -2
select_task_rq_fair 2202 2191 -11
hweight_long 66 55 -11
__reg_op 230 219 -11
dm_stats_message 2849 2833 -16
bitmap_parselist 92 74 -18
__bitmap_weight 115 97 -18
__bitmap_subset 153 129 -24
__bitmap_full 128 104 -24
__bitmap_empty 120 96 -24
bitmap_set 179 149 -30
bitmap_clear 185 155 -30
__bitmap_equal 136 105 -31
__bitmap_intersects 148 108 -40
__bitmap_complement 109 67 -42
tick_device_setup_broadcast_func.isra 81 - -81
[The increases in __bitmap_and{,not} are due to bug fixes 17/18,18/18.
No idea why bitmap_weight suddenly appears.] While 163 bytes treewide is
insignificant, I believe the bitmap functions are often called with
locks held, so saving even a few cycles might be worth it.
While making these changes, I found a few other things that might be
worth including. 16,17,18 are actual bug fixes. The rest shouldn't
change the behaviour of any of the functions, provided no-one passed
negative nbits values. If something should come up, it should be fairly
bisectable.
A few issues I thought about, but didn't know what to do with:
* Many of the functions misbehave if nbits is compile-time 0; the
out-of-line functions generally handle 0 correctly. bitmap_fill() is
particularly bad, whether the 0 is known at compile time or not. It
would probably be nice to add detection of at least compile-time 0 and
handle that appropriately.
* I didn't change __bitmap_shift_{left,right} to use unsigned because I
want to fully understand why the algorithm works before making that
change. However, AFAICT, they behave correctly for all (positive) shift
amounts. This is not the case for the small_const_nbits versions. If
for example nbits = n = BITS_PER_LONG, the shift operators turn into
no-ops (at least on x86), so one get *dst = *src, whereas one would
expect to get *dst=0. That difference in behaviour is somewhat
annoying.
This patch (of 18):
The compiler can generate slightly smaller and simpler code when it
knows that "nbits" is non-negative. Since no-one passes a negative
bit-count, this shouldn't affect the semantics.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's been nearly 3 years now since commit 55036ba76b ("lib: rename
pack_hex_byte() to hex_byte_pack()") so it's time to remove this
deprecated and unused static inline.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a helper function from drivers/ata/libata_core.c, where it is
used to blacklist particular device models. It's being moved to lib/ so
other drivers may use it for the same purpose.
This implementation in non-recursive, so is safe for the kernel stack.
[akpm@linux-foundation.org: fix sparse warning]
Signed-off-by: George Spelvin <linux@horizon.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup unused `if 0'-ed functions, which have been dead since 2006
(commits 87c2ce3b93 ("lib/zlib*: cleanups") by Adrian Bunk and
4f3865fb57 ("zlib_inflate: Upgrade library code to a recent version")
by Richard Purdie):
- zlib_deflateSetDictionary
- zlib_deflateParams
- zlib_deflateCopy
- zlib_inflateSync
- zlib_syncsearch
- zlib_inflateSetDictionary
- zlib_inflatePrime
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name was modified from hlist_add_after() to hlist_add_behind() when
adjusting the order of arguments to match the one with
klist_add_after(). This is necessary to break old code when it would
use it the wrong way.
Make klist follow this naming scheme for consistency.
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The argument names for hlist_add_after() are poorly chosen because they
look the same as the ones for hlist_add_before() but have to be used
differently.
hlist_add_after_rcu() has made a better choice.
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a8fe19ebfb ("kernel/printk: use symbolic defines for console
loglevels") makes consistent use of symbolic values for printk() log
levels.
The naming scheme used is different from the one used for
DEFAULT_MESSAGE_LOGLEVEL though. Change that symbol name to be
MESSAGE_LOGLEVEL_DEFAULT for consistency. And because the value of that
symbol comes from a similarly-named config option, rename
CONFIG_DEFAULT_MESSAGE_LOGLEVEL as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Jan Kara <jack@suse.cz>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Petr Mladek <pmladek@suse.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DEFINE_SIMPLE_ATTRIBUTE macro should not end in a ; Fix the one use
in the kernel tree that did not have a semicolon.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add zpool api.
zpool provides an interface for memory storage, typically of compressed
memory. Users can select what backend to use; currently the only
implementations are zbud, a low density implementation with up to two
compressed pages per storage page, and zsmalloc, a higher density
implementation with multiple compressed pages per storage page.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Seth Jennings <sjennings@variantweb.net>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Weijie Yang <weijie.yang@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the type of the zbud_alloc() size param from unsigned int to
size_t.
Technically, this should not make any difference, as the zbud
implementation already restricts the size to well within either type's
limits; but as zsmalloc (and kmalloc) use size_t, and zpool will use
size_t, this brings the size parameter type in line with zsmalloc/zpool.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Acked-by: Seth Jennings <sjennings@variantweb.net>
Tested-by: Seth Jennings <sjennings@variantweb.net>
Cc: Weijie Yang <weijie.yang@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When kernel device drivers or subsystems want to bind their lifespan to
t= he lifespan of the mm_struct, they usually use one of the following
methods:
1. Manually calling a function in the interested kernel module. The
funct= ion call needs to be placed in mmput. This method was rejected
by several ker= nel maintainers.
2. Registering to the mmu notifier release mechanism.
The problem with the latter approach is that the mmu_notifier_release
cal= lback is called from__mmu_notifier_release (called from exit_mmap).
That functi= on iterates over the list of mmu notifiers and don't expect
the release call= back function to remove itself from the list.
Therefore, the callback function= in the kernel module can't release the
mmu_notifier_object, which is actuall= y the kernel module's object
itself. As a result, the destruction of the kernel module's object must
to be done in a delayed fashion.
This patch adds support for this delayed callback, by adding a new
mmu_notifier_call_srcu function that receives a function ptr and calls
th= at function with call_srcu. In that function, the kernel module
releases its object. To use mmu_notifier_call_srcu, the calling module
needs to call b= efore that a new function called
mmu_notifier_unregister_no_release that as its= name implies,
unregisters a notifier without calling its notifier release call= back.
This patch also adds a function that will call barrier_srcu so those
kern= el modules can sync with mmu_notifier.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__kmap_atomic_idx is per_cpu variable. Each CPU can use KM_TYPE_NR
entries from FIXMAP i.e. from 0 to KM_TYPE_NR - 1. Allowing
__kmap_atomic_idx to over- shoot to KM_TYPE_NR can mess up with next
CPU's 0th entry which is a bug. Hence BUG_ON if __kmap_atomic_idx >=
KM_TYPE_NR.
Fix the off-by-on in this test.
Signed-off-by: Chintan Pandya <cpandya@codeaurora.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
try_set_zonelist_oom() and clear_zonelist_oom() are not named properly
to imply that they require locking semantics to avoid out_of_memory()
being reordered.
zone_scan_lock is required for both functions to ensure that there is
proper locking synchronization.
Rename try_set_zonelist_oom() to oom_zonelist_trylock() and rename
clear_zonelist_oom() to oom_zonelist_unlock() to imply there is proper
locking semantics.
At the same time, convert oom_zonelist_trylock() to return bool instead
of int since only success and failure are tested.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With memoryless node support being worked on, it's possible that for
optimizations that a node may not have a non-NULL zonelist. When
CONFIG_NUMA is enabled and node 0 is memoryless, this means the zonelist
for first_online_node may become NULL.
The oom killer requires a zonelist that includes all memory zones for
the sysrq trigger and pagefault out of memory handler.
Ensure that a non-NULL zonelist is always passed to the oom killer.
[akpm@linux-foundation.org: fix non-numa build]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series of patches fixes a problem when adding memory in bad manner.
For example: for a x86_64 machine booted with "mem=400M" and with 2GiB
memory installed, following commands cause problem:
# echo 0x40000000 > /sys/devices/system/memory/probe
[ 28.613895] init_memory_mapping: [mem 0x40000000-0x47ffffff]
# echo 0x48000000 > /sys/devices/system/memory/probe
[ 28.693675] init_memory_mapping: [mem 0x48000000-0x4fffffff]
# echo online_movable > /sys/devices/system/memory/memory9/state
# echo 0x50000000 > /sys/devices/system/memory/probe
[ 29.084090] init_memory_mapping: [mem 0x50000000-0x57ffffff]
# echo 0x58000000 > /sys/devices/system/memory/probe
[ 29.151880] init_memory_mapping: [mem 0x58000000-0x5fffffff]
# echo online_movable > /sys/devices/system/memory/memory11/state
# echo online> /sys/devices/system/memory/memory8/state
# echo online> /sys/devices/system/memory/memory10/state
# echo offline> /sys/devices/system/memory/memory9/state
[ 30.558819] Offlined Pages 32768
# free
total used free shared buffers cached
Mem: 780588 18014398509432020 830552 0 0 51180
-/+ buffers/cache: 18014398509380840 881732
Swap: 0 0 0
This is because the above commands probe higher memory after online a
section with online_movable, which causes ZONE_HIGHMEM (or ZONE_NORMAL
for systems without ZONE_HIGHMEM) overlaps ZONE_MOVABLE.
After the second online_movable, the problem can be observed from
zoneinfo:
# cat /proc/zoneinfo
...
Node 0, zone Movable
pages free 65491
min 250
low 312
high 375
scanned 0
spanned 18446744073709518848
present 65536
managed 65536
...
This series of patches solve the problem by checking ZONE_MOVABLE when
choosing zone for new memory. If new memory is inside or higher than
ZONE_MOVABLE, makes it go there instead.
After applying this series of patches, following are free and zoneinfo
result (after offlining memory9):
bash-4.2# free
total used free shared buffers cached
Mem: 780956 80112 700844 0 0 51180
-/+ buffers/cache: 28932 752024
Swap: 0 0 0
bash-4.2# cat /proc/zoneinfo
Node 0, zone DMA
pages free 3389
min 14
low 17
high 21
scanned 0
spanned 4095
present 3998
managed 3977
nr_free_pages 3389
...
start_pfn: 1
inactive_ratio: 1
Node 0, zone DMA32
pages free 73724
min 341
low 426
high 511
scanned 0
spanned 98304
present 98304
managed 92958
nr_free_pages 73724
...
start_pfn: 4096
inactive_ratio: 1
Node 0, zone Normal
pages free 32630
min 120
low 150
high 180
scanned 0
spanned 32768
present 32768
managed 32768
nr_free_pages 32630
...
start_pfn: 262144
inactive_ratio: 1
Node 0, zone Movable
pages free 65476
min 241
low 301
high 361
scanned 0
spanned 98304
present 65536
managed 65536
nr_free_pages 65476
...
start_pfn: 294912
inactive_ratio: 1
This patch (of 7):
Introduce zone_for_memory() in arch independent code for
arch_add_memory() use.
Many arch_add_memory() function simply selects ZONE_HIGHMEM or
ZONE_NORMAL and add new memory into it. However, with the existance of
ZONE_MOVABLE, the selection method should be carefully considered: if
new, higher memory is added after ZONE_MOVABLE is setup, the default
zone and ZONE_MOVABLE may overlap each other.
should_add_memory_movable() checks the status of ZONE_MOVABLE. If it
has already contain memory, compare the address of new memory and
movable memory. If new memory is higher than movable, it should be
added into ZONE_MOVABLE instead of default zone.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Mel Gorman" <mgorman@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a comment describing the circumstances in which
__lock_page_or_retry() will or will not release the mmap_sem when
returning 0.
Add comments to lock_page_or_retry()'s callers (filemap_fault(),
do_swap_page()) noting the impact on VM_FAULT_RETRY returns.
Add comments on up the call tree, particularly replacing the false "We
return with mmap_sem still held" comments.
Signed-off-by: Paul Cassella <cassella@cray.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fair zone allocation policy round-robins allocations between zones
within a node to avoid age inversion problems during reclaim. If the
first allocation fails, the batch counts are reset and a second attempt
made before entering the slow path.
One assumption made with this scheme is that batches expire at roughly
the same time and the resets each time are justified. This assumption
does not hold when zones reach their low watermark as the batches will
be consumed at uneven rates. Allocation failure due to watermark
depletion result in additional zonelist scans for the reset and another
watermark check before hitting the slowpath.
On UMA, the benefit is negligible -- around 0.25%. On 4-socket NUMA
machine it's variable due to the variability of measuring overhead with
the vmstat changes. The system CPU overhead comparison looks like
3.16.0-rc3 3.16.0-rc3 3.16.0-rc3
vanilla vmstat-v5 lowercost-v5
User 746.94 774.56 802.00
System 65336.22 32847.27 40852.33
Elapsed 27553.52 27415.04 27368.46
However it is worth noting that the overall benchmark still completed
faster and intuitively it makes sense to take as few passes as possible
through the zonelists.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zone->pages_scanned is a write-intensive cache line during page reclaim
and it's also updated during page free. Move the counter into vmstat to
take advantage of the per-cpu updates and do not update it in the free
paths unless necessary.
On a small UMA machine running tiobench the difference is marginal. On
a 4-node machine the overhead is more noticable. Note that automatic
NUMA balancing was disabled for this test as otherwise the system CPU
overhead is unpredictable.
3.16.0-rc3 3.16.0-rc3 3.16.0-rc3
vanillarearrange-v5 vmstat-v5
User 746.94 759.78 774.56
System 65336.22 58350.98 32847.27
Elapsed 27553.52 27282.02 27415.04
Note that the overhead reduction will vary depending on where exactly
pages are allocated and freed.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arrangement of struct zone has changed over time and now it has
reached the point where there is some inappropriate sharing going on.
On x86-64 for example
o The zone->node field is shared with the zone lock and zone->node is
accessed frequently from the page allocator due to the fair zone
allocation policy.
o span_seqlock is almost never used by shares a line with free_area
o Some zone statistics share a cache line with the LRU lock so
reclaim-intensive and allocator-intensive workloads can bounce the cache
line on a stat update
This patch rearranges struct zone to put read-only and read-mostly
fields together and then splits the page allocator intensive fields, the
zone statistics and the page reclaim intensive fields into their own
cache lines. Note that the type of lowmem_reserve changes due to the
watermark calculations being signed and avoiding a signed/unsigned
conversion there.
On the test configuration I used the overall size of struct zone shrunk
by one cache line. On smaller machines, this is not likely to be
noticable. However, on a 4-node NUMA machine running tiobench the
system CPU overhead is reduced by this patch.
3.16.0-rc3 3.16.0-rc3
vanillarearrange-v5r9
User 746.94 759.78
System 65336.22 58350.98
Elapsed 27553.52 27282.02
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was formerly the series "Improve sequential read throughput" which
noted some major differences in performance of tiobench since 3.0.
While there are a number of factors, two that dominated were the
introduction of the fair zone allocation policy and changes to CFQ.
The behaviour of fair zone allocation policy makes more sense than
tiobench as a benchmark and CFQ defaults were not changed due to
insufficient benchmarking.
This series is what's left. It's one functional fix to the fair zone
allocation policy when used on NUMA machines and a reduction of overhead
in general. tiobench was used for the comparison despite its flaws as
an IO benchmark as in this case we are primarily interested in the
overhead of page allocator and page reclaim activity.
On UMA, it makes little difference to overhead
3.16.0-rc3 3.16.0-rc3
vanilla lowercost-v5
User 383.61 386.77
System 403.83 401.74
Elapsed 5411.50 5413.11
On a 4-socket NUMA machine it's a bit more noticable
3.16.0-rc3 3.16.0-rc3
vanilla lowercost-v5
User 746.94 802.00
System 65336.22 40852.33
Elapsed 27553.52 27368.46
This patch (of 6):
The LRU insertion and activate tracepoints take PFN as a parameter
forcing the overhead to the caller. Move the overhead to the tracepoint
fast-assign method to ensure the cost is only incurred when the
tracepoint is active.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently map_vm_area() takes (struct page *** pages) as third argument,
and after mapping, it moves (*pages) to point to (*pages +
nr_mappped_pages).
It looks like this kind of increment is useless to its caller these
days. The callers don't care about the increments and actually they're
trying to avoid this by passing another copy to map_vm_area().
The caller can always guarantee all the pages can be mapped into vm_area
as specified in first argument and the caller only cares about whether
map_vm_area() fails or not.
This patch cleans up the pointer movement in map_vm_area() and updates
its callers accordingly.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 71e3aac072 ("thp: transparent hugepage core") adds
copy_pte_range prototype to huge_mm.h. I'm not sure why (or if) this
function have been used outside of memory.c, but it currently isn't.
This patch makes copy_pte_range() static again.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They are unnecessary: "zero" can be used in place of "hugetlb_zero" and
passing extra2 == NULL is equivalent to infinity.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do we really need an exported alias for __SetPageReferenced()? Its
callers better know what they're doing, in which case the page would not
be already marked referenced. Kill init_page_accessed(), just
__SetPageReferenced() inline.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
