The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It should use ad7797_attribute_group in ad7797_info,
according to commit ("iio:ad7793: Add support for the ad7796 and ad7797").
Scale is fixed for the ad7796 and not programmable, hence
should not have the scale_available attribute.
Fixes: fd1a8b9128 ("iio:ad7793: Add support for the ad7796 and ad7797")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
-----BEGIN PGP SIGNATURE-----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=uJ0W
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 5.6 cycle.
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
* tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ping: set pa_laser_ping_cfg in of_ping_match
iio: chemical: sps30: fix missing triggered buffer dependency
iio: st_sensors: remap SMO8840 to LIS2DH12
iio: light: vcnl4000: update sampling periods for vcnl4040
iio: light: vcnl4000: update sampling periods for vcnl4200
iio: accel: adxl372: Set iio_chan BE
iio: magnetometer: ak8974: Fix negative raw values in sysfs
iio: trigger: stm32-timer: disable master mode when stopping
iio: adc: stm32-dfsdm: fix sleep in atomic context
iio: adc: at91-sama5d2_adc: fix differential channels in triggered mode
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't confuse user with meaningless warning about the failure in getting
regulators in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move ad7192 ADC driver out of staging into mainline.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the posibility do read and write registers from userspace
using the kernel debug direct register access option.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Modify NPCM ADC reset support from
direct register access to reset controller support.
please make sure to modify NPCM adc device tree
parameters as described at nuvoton,npcm-adc.txt
document for using this change.
Note for anyone noting that this is a breaking change, this is on
a BMC and effectively in a close ecosystem so it is fine to rely
on DT and kernel being updated together.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the LOW_PASS_FILTER_3DB_FREQUENCY attribute
in iio_chan_spec for each channel. The used filters are sinc3
or sinc4. The filter type with the highest output data rate
is used when setting a low pass frequency in the channel's sysfs.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit fixes the error message:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
Suppress the trigger irq handler. Make the buffer transfers directly
in DMA callback, instead.
Push buffers without timestamps, as timestamps are not supported
in DFSDM driver.
Fixes: 11646e81d7 ("iio: adc: stm32-dfsdm: add support for buffer modes")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The differential channels require writing the channel offset register (COR).
Otherwise they do not work in differential mode.
The configuration of COR is missing in triggered mode.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not print an error trace when deferring probe for some resource.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ad7124 data-sheet specifies that the falling edge
of the DOUT line should be used for an interrupt.
The current irq flag (IRQF_TRIGGER_LOW) used will
cause unwanted behaviour. When enabling the interrupt
it will fire once because the DOUT line is already low.
This will make the driver to read an unfinished conversion
from the chip.
This patch sets the irq type to the one specified in
the data-sheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch the ad_sigma_delta implementation hardcoded
the irq trigger type to low, assuming that all Sigma-Delta ADCs
have the same interrupt-type.
This patch allows all drivers using the ad_sigma_delta layer to set the
irq trigger type to the one specified in the datasheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update sampling rate when oversampling ratio is changed
through the IIO ABI.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Apply data formatting to single conversion,
as this is already done in continuous and trigger modes.
Fixes: 102afde629 ("iio: adc: stm32-dfsdm: manage data resolution in trigger mode")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Cc: <Stable@vger.kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes device tree channel configuration.
ad7124 driver reads channels configuration from the device tree.
It expects to find channel specifications as child nodes.
Before this patch ad7124 driver assumed that the child nodes are parsed
by for_each_available_child_of_node in the order 0,1,2,3...
This is wrong and the real order of the children can be seen by running:
dtc -I fs /sys/firmware/devicetree/base on the machine.
For example, running this on an rpi 3B+ yields the real
children order: 4,2,0,7,5,3,1,6
Before this patch the driver assigned the channel configuration
like this:
- 0 <- 4
- 1 <- 2
- 2 <- 0
........
For example, the symptoms can be observed by connecting the 4th channel
to a 1V tension and then reading the in_voltage0-voltage19_raw sysfs
(multiplied of course by the scale) one would see that channel 0
measures 1V and channel 4 measures only noise.
Now the driver uses the reg property of each child in order to
correctly identify to which channel the parsed configuration
belongs to.
Fixes b3af341bbd: ("iio: adc: Add ad7124 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
The dma_request_chan() is the standard API to request slave channel,
clients should be moved away from the legacy API to allow us to retire
them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
-----BEGIN PGP SIGNATURE-----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=8FmM
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
iio: accel: bma180: BMA254 support
iio: pressure: bmp280: Allow device to be enumerated from ACPI
iio: pressure: bmp280: Drop ACPI support
dt-bindings: iio: adc: convert sd modulator to json-schema
iio: buffer: rename 'read_first_n' callback to 'read'
iio: buffer-dmaengine: Report buffer length requirements
bindings: iio: pressure: Add documentation for dlh driver
dt-bindings: Add asc vendor
iio: pressure: Add driver for DLH pressure sensors
iio: buffer-dmaengine: Add module information
iio: accel: bma180: Use explicit member assignment
iio: accel: bma180: Basic regulator support
iio: accel: bma180: Add dev helper variable
iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
iio: imu: st_lsm6dsx: check if pull_up is located in primary page
iio: imu: st_lsm6dsx: check if master_enable is located in primary page
iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
iio: light: remove unneeded semicolon
...
The ad7928 is software compatible with the ad7923.
The ad7908 and ad7918 are the 8 and 10-bit versions of the ad7928.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Accomplish device tree compatibility to driver AD7923
by adding of_device_id table and making a subsequent call to
MODULE_DEVICE_TABLE.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix checkpatch warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
+static int ad7923_scan_direct(struct ad7923_state *st, unsigned ch)
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Removes the unused define AD7923_CHANNEL_x from the code.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This chip is similar to the LTC2497 ADC, it just uses SPI instead of I2C
and so has a slightly different protocol. Only the actual hardware
access is different. The spi protocol is different enough to not be able
to map the differences via a regmap.
Also generalize the entry in MAINTAINER to cover the newly introduced
file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This allows to share most of this driver for the ltc2496 driver added in
the next commit that is an SPI variant of the ltc2497. Initially I named
the generic part ltc249x, but wild card names are frowned upon, so the
generic part is called ltc2497-core even though it's not obvious that
this is then to be reused for the ltc2496 driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Platform data is a legacy interface to supply device properties
to the driver. In this case we even don't have in-kernel users
for it. Just remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable overrun interrupt on STM32 ADC. In case data register hasn't been
read (by CPU or DMA), overrun condition is detected when there's new
conversion data available. Stop grabbing data and log an error message.
Use a threaded irq to avoid printing the error message from hard irq
context.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ad7091R5 was added in a non alphabetical order after AD7124 in Makefile and
KConfig. This patch fixes that and place Ad7091R5 before AD7124.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7266 have no in-tree users making use of the platform
data mechanism to pass address GPIO lines when not using
a fixed address, so we can easily convert this to use
GPIO descriptors instead of the platform data integers
currently passed.
Lowercase the labels "ad0".."ad2" as this will make a better
fit for platform descriptions like device tree that prefer
lowercase names such as "ad0-gpios" rather than "AD0-gpios".
Board files and other static users of this device can pass
the same GPIO descriptors using machine descriptor
tables if need be.
Cc: Alison Schofield <amsfield22@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The device is always in a low-power state due to the hardware design. It
wakes up upon a conversion request and goes back into the low-power
state. The pm ops are added to disable the device completely and to free
the regulator. Disbaling the device completely should be not that
notable but freeing the regulator is important. Because if it is a shared
power-rail the regulator won't be disabled during suspend-to-ram/disk
and so all devices connected to that rail keeps on.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The channels specification assignment in chip info was simplified.
This patch makes supporting other devices by this driver easier.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
-----BEGIN PGP SIGNATURE-----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=vySY
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of fixes for IIO in the 5.5 cycle.
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
* tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
iio: adc: max1027: fix not unregistered iio trigger
iio: adc: intel_mrfld_adc: Allocating too much data in probe()
iio: adc: ad7124: Enable internal reference
dt-bindings: iio: adc: ad7292: fix constraint over channel quantity
dt-bindings: iio: adc: ad7292: Update SPDX identifier
iio: temperature: ltc2983: fix u32 read into a unsigned long long
iio: st_accel: Fix unused variable warning
iio: adc: ad7606: fix reading unnecessary data from device
As of commit b9ddd50911 ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
Fixes: 69780a3bbc ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Each time we need to read a sample (from the sysfs interface, since the
driver supports only it) the driver writes the configuration register
with the proper settings needed to perform the said read, then it runs
another xfer to actually read the resulting value. Most notably the
configuration register is updated to set the ADC internal MUX depending by
which channel the read targets.
Unfortunately this seems not enough to ensure correct operation because
the ADC works in a pipelined-like fashion and the new configuration isn't
applied in time.
The ADC alternates two phases: acquisition and conversion. During the
acquisition phase the ADC samples the analog signal in an internal
capacitor; in the conversion phase the ADC performs the actual analog to
digital conversion of the stored voltage. Note that of course the MUX
needs to be set to the proper channel when the acquisition phase is
performed.
Once the conversion phase has been completed, the device automatically
switches back to a new acquisition; on the other hand the device switches
from acquisition to conversion on the rising edge of SPI cs signal (that
is when the xfer finishes).
Only after both two phases have been completed (with the proper settings
already written in the configuration register since the beginning) it is
possible to read the outcome from SPI bus.
With the current driver implementation, we end up in the following
situation:
_______ 1st xfer ____________ 2nd xfer ___________________
SPI cs.. \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle | val N-1 + idle ...
SPI wr.. idle | cfg N + idle | (X) + idle ...
------------------------ + -------------------- + ------------------
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1
As shown in the diagram above, the value we read in the Nth read belongs
to configuration setting N-1.
In case the configuration is not changed (config[N] == config[N-1]), then
we still get correct data, but in case the configuration changes (i.e.
switching the MUX on another channel), we get wrong data (data from the
previously selected channel).
This patch fixes this by performing one more "dummy" transfer in order to
ending up in reading the data when it's really ready, as per the following
timing diagram.
_______ 1st xfer ____________ 2nd xfer ___________ 3rd xfer ___
SPI cs.. \_________/ \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle |(val N-1)+ idle | val N + ..
SPI wr.. idle | cfg N + idle | (X) + idle | (X) + ..
------------------------ + -------------------- + ------------------- + --
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1 | ..
NOTE: in the latter case (cfg changes), the acquisition phase for the
value to be read begins after the 1st xfer, that is after the read request
has been issued on sysfs. On the other hand, if the cfg doesn't change,
then we can refer to the fist diagram assuming N == (N - 1); the
acquisition phase _begins_ before the 1st xfer (potentially a lot of time
before the read has been issued via sysfs, but it _ends_ after the 1st
xfer, that is _after_ the read has started. This should guarantee a
reasonably fresh data, which value represents the voltage that the sampled
signal has after the read start or maybe just around it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver forgets to unregister the iio trigger in probe failure and
remove.
Use devm API to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
