Using RBP as a temporary register breaks frame pointer convention and
breaks stack traces when unwinding from an interrupt in the crypto code.
Swap the usages of R12 and RBP. Use R12 for the REG_D register, and use
RBP to store the pre-aligned stack pointer.
Reported-by: Eric Biggers <ebiggers@google.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Eric Biggers <ebiggers@google.com>
Acked-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit ea4d26ae ("raid5: add AVX optimized RAID5 checksumming")
introduced x86/ arch wide defines for AFLAGS and CFLAGS indicating AVX
support in binutils based on the same test we have in x86/crypto/ right
now. To minimize duplication drop our implementation in favour to the
one in x86/.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is an assembler implementation of the SHA1 algorithm using the
Supplemental SSE3 (SSSE3) instructions or, when available, the
Advanced Vector Extensions (AVX).
Testing with the tcrypt module shows the raw hash performance is up to
2.3 times faster than the C implementation, using 8k data blocks on a
Core 2 Duo T5500. For the smalest data set (16 byte) it is still 25%
faster.
Since this implementation uses SSE/YMM registers it cannot safely be
used in every situation, e.g. while an IRQ interrupts a kernel thread.
The implementation falls back to the generic SHA1 variant, if using
the SSE/YMM registers is not possible.
With this algorithm I was able to increase the throughput of a single
IPsec link from 344 Mbit/s to 464 Mbit/s on a Core 2 Quad CPU using
the SSSE3 variant -- a speedup of +34.8%.
Saving and restoring SSE/YMM state might make the actual throughput
fluctuate when there are FPU intensive userland applications running.
For example, meassuring the performance using iperf2 directly on the
machine under test gives wobbling numbers because iperf2 uses the FPU
for each packet to check if the reporting interval has expired (in the
above test I got min/max/avg: 402/484/464 MBit/s).
Using this algorithm on a IPsec gateway gives much more reasonable and
stable numbers, albeit not as high as in the directly connected case.
Here is the result from an RFC 2544 test run with a EXFO Packet Blazer
FTB-8510:
frame size sha1-generic sha1-ssse3 delta
64 byte 37.5 MBit/s 37.5 MBit/s 0.0%
128 byte 56.3 MBit/s 62.5 MBit/s +11.0%
256 byte 87.5 MBit/s 100.0 MBit/s +14.3%
512 byte 131.3 MBit/s 150.0 MBit/s +14.2%
1024 byte 162.5 MBit/s 193.8 MBit/s +19.3%
1280 byte 175.0 MBit/s 212.5 MBit/s +21.4%
1420 byte 175.0 MBit/s 218.7 MBit/s +25.0%
1518 byte 150.0 MBit/s 181.2 MBit/s +20.8%
The throughput for the largest frame size is lower than for the
previous size because the IP packets need to be fragmented in this
case to make there way through the IPsec tunnel.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Maxim Locktyukhin <maxim.locktyukhin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
