MAC addresses along with an identifying index are offloaded to firmware to
allow tunnel decapsulation. If a tunnel packet arrives with a matching
destination MAC address and a verified index, it can continue on the
decapsulation process. This replicates the MAC verifications carried out
in the kernel network stack.
When a netdev is added to a bridge (e.g. OvS) then packets arriving on
that dev are directed through the bridge datapath instead of passing
through the network stack. Therefore, tunnelled packets matching the MAC
of that dev will not be decapped here.
Replicate this behaviour on firmware by removing offloaded MAC addresses
when a MAC representer is added to an OvS bridge. This can prevent any
false positive tunnel decaps.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-tunnel rules are TC flower and OvS rules that forward a packet to the
tunnel end point where it can then pass through the network stack and be
decapsulated. These are required if the tunnel end point is, say, an OvS
internal port.
Currently, firmware determines that a packet is in a tunnel and decaps it
if it has a known destination IP and MAC address. However, this bypasses
the flower pre-tunnel rule and so does not update the stats. Further to
this it ignores VLANs that may exist outside of the tunnel header.
Offload pre-tunnel rules to the NFP. This embeds the pre-tunnel rule into
the tunnel decap process based on (firmware) mac index and VLAN. This
means that decap can be carried out correctly with VLANs and that stats
can be updated for all kernel rules correctly.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-tunnel rules must direct packets to an internal port based on L2
information. Rules that egress to an internal port are already indicated
by a non-NULL device in its nfp_fl_payload struct. Verfiy the rest of the
match fields indicate that the rule is a pre-tunnel rule. This requires a
full match on the destination MAC address, an option VLAN field, and no
specific matches on other lower layer fields (with the exception of L4
proto and flags).
If a rule is identified as a pre-tunnel rule then mark it for offload to
the pre-tunnel table. Similarly, remove it from the pre-tunnel table on
rule deletion. The actual offloading of these commands is left to a
following patch.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-tunnel rules are used when the tunnel end-point is on an 'internal
port'. These rules are used to direct the tunnelled packets (based on outer
header fields) to the internal port where they can be detunnelled. The
rule must send the packet to ingress the internal port at the TC layer.
Currently FW does not support an action to send to ingress so cannot
offload such rules. However, in preparation for populating the pre-tunnel
table to represent such rules, check for rules that send to the ingress of
an internal port and mark them as such. Further validation of such rules
is left to subsequent patches.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP allows the merging of 2 flows together into a single offloaded flow.
In the kernel datapath the packet must match 1 flow, impliment its
actions, recirculate, match the 2nd flow and also impliment its actions.
Merging creates a single flow with all actions from the 2 original flows.
Firmware impliments a tunnel header push as the packet is about to egress
the card. Therefore, if the first merge rule candiate pushes a tunnel,
then the second rule can only have an egress action for a valid merge to
occur (or else the action ordering will be incorrect). This prevents the
pushing of a tunnel header followed by the pushing of a vlan header.
In order to support this behaviour, firmware allows VLAN information to
be encoded in the tunnel push action. If this is non zero then the fw will
push a VLAN after the tunnel header push meaning that 2 such flows with
these actions can be merged (with action order being maintained).
Support tunnel in VLAN pushes by encoding VLAN information in the tunnel
push action of any merge flow requiring this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-08-04
This series contains more updates to fm10k from Jake Keller.
Jake removes the unnecessary initialization of some variables to help
resolve static code checker warnings. Explicitly return success during
resume, since the value of 'err' is always success. Fixed a issue with
incrementing a void pointer, which can produce undefined behavior. Used
the __always_unused macro for function templates that are passed as
parameters in functions, but are not used. Simplified the code by
removing an unnecessary macro in determining the value of NON_Q_VECTORS.
Fixed an issue, using bitwise operations to prevent the low address
overwriting the high portion of the address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize PCIe PHY initialization with vendor driver version 8.047.01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for MAC OCP read-modify-write operations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code piece was inherited from RTL8139 code, the register at
address 0x5c however has a different meaning on RTL8169 and is unused.
So we can remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 171a9bae68 ("staging/octeon: Allow test build on
!MIPS"), the following combination of configs cause a few Kconfig
warnings and build errors (distilled from arm allyesconfig and Randy's
randconfig builds):
CONFIG_NETDEVICES=y
CONFIG_STAGING=y
CONFIG_COMPILE_TEST=y
and CONFIG_OCTEON_ETHERNET as either a module or built-in.
WARNING: unmet direct dependencies detected for MDIO_OCTEON
Depends on [n]: NETDEVICES [=y] && MDIO_DEVICE [=y] && MDIO_BUS [=y]
&& 64BIT [=n] && HAS_IOMEM [=y] && OF_MDIO [=n]
Selected by [y]:
- OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC ||
COMPILE_TEST [=y]) && NETDEVICES [=y]
In file included from ../drivers/net/phy/mdio-octeon.c:14:
../drivers/net/phy/mdio-cavium.h:111:36: error: implicit declaration of
function ‘writeq’; did you mean ‘writel’?
[-Werror=implicit-function-declaration]
111 | #define oct_mdio_writeq(val, addr) writeq(val, (void *)addr)
| ^~~~~~
CONFIG_64BIT is not strictly necessary if the proper readq/writeq
definitions are included from io-64-nonatomic-lo-hi.h.
CONFIG_OF_MDIO is not needed when CONFIG_COMPILE_TEST is enabled because
of commit f9dc9ac516 ("of/mdio: Add dummy functions in of_mdio.h.").
Fixes: 171a9bae68 ("staging/octeon: Allow test build on !MIPS")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kconfig option is unused, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the two headers into one, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ksz_port_cleanup(), which is unused. Add missing include
"ksz_common.h", which fixes the following warning when built with
make ... W=1
drivers/net/dsa/microchip/ksz_common.c:23:6: warning: no previous prototype for ‘...’ [-Wmissing-prototypes]
Note that the order of the headers cannot be swapped, as that would
trigger missing forward declaration errors, which would indicate the
way forward is to merge the two headers into one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is relying on zero'ed allocated memory and does not
explicitly call atomic_set() to initialize the ref counts to 0. Add
these atomic_set() calls so that it will be more straight forward
to convert atomic ref counts to refcount_t.
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: <GR-Linux-NIC-Dev@marvell.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Misc updates for mlx5 netdev driver:
1) Ingress rate support for E-Switch vports from Eli.
2) Gavi introduces flow counters bulk allocation and pool,
To improve the performance of flow counter acquisition.
3) From Tariq, micro improvements for tx path
4) From Shay, small improvement for XDP TX MPWQE inline flow.
5) Aya provides some cleanups for tx devlink health reporters.
6) Saeed, refactor checksum handling into a single function.
7) Tonghao, allows dropping specific tunnel packets.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl1DPo0ACgkQSD+KveBX
+j4Pagf/fUREI8/UqNIrG+brwWFVSO2KeIRYiYfIJbocRanKPIuJcXPJd+5BQ6Ap
PHCt395bDDnKGjBeDJNQq4NL9o7iVkr+w92a6G5Zut409al+C3JZDFLunQEF8ffe
xKEoRbE8MzrxGf/LL5h7s/mbkilDaN1ZXuVvwgyZV7WqG8fg54+VQH+omRAG3LOx
Ppd4fuNuPInWFlzGe/iwbfCejLq1UtVxQzOcB23Eoju5u1RRkkYirWv9xkRhOZ1I
bIM/vXf+V0DG158ypmEnAjv742TNHg9R1MAVQU0t/SxyaU7UlHLAAie6zU9t9GX9
dammeyRTXjEoCu74sLo3I/UbBp/e8w==
=wpVY
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-08-01
Misc updates for mlx5 netdev driver:
1) Ingress rate support for E-Switch vports from Eli.
2) Gavi introduces flow counters bulk allocation and pool,
To improve the performance of flow counter acquisition.
3) From Tariq, micro improvements for tx path
4) From Shay, small improvement for XDP TX MPWQE inline flow.
5) Aya provides some cleanups for tx devlink health reporters.
6) Saeed, refactor checksum handling into a single function.
7) Tonghao, allows dropping specific tunnel packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix assignment of the FM10K_FAULT_ADDR_LO register into fault->address
by using a bit-wise |= operation. Without this, the low address is
completely overwriting the high potion of the address. This caused the
fault to incorrectly return only the lower 32 bits of the fault address.
This issue was detected by cppcheck and resolves the following warnings
produced by that tool:
[fm10k_pf.c:1668] -> [fm10k_pf.c:1670]: (style) Variable
'fault->address' is reassigned a value before the old one has been used.
[fm10k_pf.c:1669] -> [fm10k_pf.c:1670]: (style) Variable
'fault->address' is reassigned a value before the old one has been used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver currently uses a macro to decide whether we should use
NON_Q_VECTORS_PF or NON_Q_VECTORS_VF.
However, we also define NON_Q_VECTORS_VF to the same value as
NON_Q_VECTORS_PF. This means that the macro NON_Q_VECTORS(hw) will
always return the same value.
Let's just remove this macro, and replace it directly with an enum value
on the enum non_q_vectors.
This was detected by cppcheck and fixes the following warnings when
building with BUILD=KERNEL
[fm10k_ethtool.c:1123]: (style) Same value in both branches of ternary
operator.
[fm10k_ethtool.c:1142]: (style) Same value in both branches of ternary
operator.
[fm10k_main.c:1826]: (style) Same value in both branches of ternary
operator.
[fm10k_main.c:1849]: (style) Same value in both branches of ternary
operator.
[fm10k_main.c:1858]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:901]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:1040]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:1726]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:1763]: (style) Same value in both branches of ternary
operator.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several functions in the fm10k driver have specific function templates,
as they are used as function pointers. The parameters in these functions
are not always used. Explicitly mark unused parameters with the
__always_unused macro, so that the compiler will not warn about them
when building with the -Wunused-parameter warning enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The page_addr variable is a void pointer. Incrementing it before calling
prefetch is technically undefined. Fix this by casting it to a u8*
pointer before incrementing it. This ensures that we increment the
pointer value in byte units, instead of relying on this undefined
behavior.
This was detected by cppcheck, and resolves the following warning
produced by that tool:
[fm10k_main.c:328]: (portability) 'page_addr' is of type 'void *'. When
using void pointers in calculations, the behaviour is undefined.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the fm10k_handle_resume function, return 0 explicitly at the end of
the function instead of returning the err value.
This was detected by cppcheck and resolves the following style warning
produced by that tool:
[fm10k_pci.c:2768] -> [fm10k_pci.c:2787]: (warning) Identical condition
'err', second condition is always false
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable 'size' in fm10k_dfwd_add_station is initialized, but
is always re-assigned immediately before use. Remove this unnecessary
initialization.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[fm10k_netdev.c:1466]: (style) Variable 'size' is assigned a value that is never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable err in several functions in the fm10k_netdev.c file
is initialized with a value that is never used. The err value is
immediately re-assigned in all cases where it will be checked. Remove
the unnecessary initializers.
This was detected by cppcheck and resolves the following warnings
produced by that tool:
[fm10k_netdev.c:999] -> [fm10k_netdev.c:1004]: (style) Variable 'err' is
reassigned a value before the old one has been used.
[fm10k_netdev.c:1019] -> [fm10k_netdev.c:1024]: (style) Variable 'err'
is reassigned a value before the old one has been used.
[fm10k_netdev.c:64]: (style) Variable 'err' is assigned a value that is
never used.
[fm10k_netdev.c:131]: (style) Variable 'err' is assigned a value that
is never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The err variable in the fm10k_tlv_attr_parse function is initialized
with zero. However, the function never reads err without first assigning
it from a function call. Remove this unnecessary initialization.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[fm10k_tlv.c:498]: (style) Variable 'err' is assigned a value that is
never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-08-01
This series for fm10k, by Jake Keller, reduces the scope of local variables
where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC ports can manage the MDIO bus via local register
interface. However there's also a centralized way
to manage the MDIO bus, via the MDIO PCIe endpoint
device integrated by the same root complex that also
integrates the ENETC ports (eth controllers).
Depending on board design and use case, centralized
access to MDIO may be better than using local ENETC
port registers. For instance, on the LS1028A QDS board
where MDIO muxing is required. Also, the LS1028A on-chip
switch doesn't have a local MDIO register interface.
The current patch registers the above PCIe endpoint as a
separate MDIO bus and provides a driver for it by re-using
the code used for local MDIO access. It also allows the
ENETC port PHYs to be managed by this driver if the local
"mdio" node is missing from the ENETC port node.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up overcomplicated makefile to make it more maintainable.
Basically, there's a set of common objects shared between
the PF and VF driver modules. This can be implemented in a
simpler way, without conditionals, less repetition, allowing
also for easier updates in the future.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What's needed is basically a pointer to the mdio registers.
This is one way to store it inside bus->priv allocated space,
without upsetting sparse.
Reworked accessors to avoid __iomem casting.
Used devm_* variant to further clean up the init error /
remove paths.
Fixes following sparse warning:
warning: incorrect type in assignment (different address spaces)
expected void *priv
got struct enetc_mdio_regs [noderef] <asn:2>*[assigned] regs
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds PTP support for the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is done for all the other structs within this driver.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6250 family doesn't support the MV88E6XXX_PORT_CTL1_MESSAGE_PORT
bit.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this it is possible to mark certain chip ports as invalid. This is
required for example for the MV88E6220 (which is in general a MV88E6250
with 7 ports) but the ports 2-4 are not routed to pins.
If a user configures an invalid port, an error is returned.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensures we can talk to a PHY via MDIO on the AST2600, as the MDIO
controller is now separate from the MAC.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy-handle is necessary for the AST2600 which separates the MDIO
controllers from the MAC.
I've tried to minimise the intrusion of supporting the AST2600 to the
FTGMAC100 by leaving in place the existing MDIO support for the embedded
MDIO interface. The AST2400 and AST2500 continue to be supported this
way, as it avoids breaking/reworking existing devicetrees.
The AST2600 support by contrast requires the presence of the phy-handle
property in the MAC devicetree node to specify the appropriate PHY to
associate with the MAC. In the event that someone wants to specify the
MDIO bus topology under the MAC node on an AST2400 or AST2500, the
current auto-probe approach is done conditional on the absence of an
"mdio" child node of the MAC.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.
The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the scope of the ring local variable in the fm10k_assign_l2_accel
function.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[fm10k_netdev.c:1447]: (style) The scope of the variable 'ring' can be
reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the result local variable in the
fm10k_iov_msg_lport_state_pf function.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[fm10k_pf.c:1435]: (style) The scope of the variable 'result' can be
reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The msg variable in the fm10k_mbx_validate_msg_size and
fm10k_sm_mbx_transmit functions is only used within the do {} loop
scope. Reduce its scope only to where it is used.
This was detected by cppcheck, and resolves the following warnings
produced by that tool:
[fm10k_mbx.c:299]: (style) The scope of the variable 'msg' can be reduced.
[fm10k_mbx.c:2004]: (style) The scope of the variable 'msg' can be reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the local loop variable in the
fm10k_check_hang_subtask function.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[driver/fm10k_pci.c:852]: (style) The scope of the variable 'i' can be
reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the local variable err in the fm10k_detach_subtask
function.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[fm10k_pci.c:403]: (style) The scope of the variable 'err' can be reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The tx_buffer local variable in the function fm10k_clean_tx_ring is not
used except inside a smaller block scope. Reduce the scope to its point
of use.
This was detected by cppcheck and resolves the following style warning
produced by that tool:
[fm10k_netdev.c:179]: (style) The scope of the variable 'tx_buffer' can
be reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the q_idx local variable in the fm10k_cache_ring_qos
function.
This was detected by cppcheck and resolves the following style warning
produced by that tool:
[fm10k_main.c:2016]: (style) The scope of the variable 'q_idx' can be
reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the local err variable in the fm10k_iov_alloc_data
function.
This was detected by cppcheck and resolves the following style warning
produced by that tool:
[fm10k_iov.c:426]: (style) The scope of the variable 'err' can be reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the qv vector pointer local variable in the
fm10k_set_coalesce function.
This was detected by cppcheck and resolves the following style warning
produced by that tool:
[fm10k_ethtool.c:658]: (style) The scope of the variable 'qv' can be
reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the char *p local variable to only the block where
it is used.
This was detected by cppcheck and resolves the following style warning
produced by that tool:
[fm10k_ethtool.c:229]: (style) The scope of the variable 'p' can be
reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the scope of the err local variable in the fm10k_dcbnl_ieee_setets
function.
This was detected using cppcheck, and resolves the following style
warning:
[fm10k_dcbnl.c:37]: (style) The scope of the variable 'err' can be reduced.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read and
_mv88e6xxx_port_vlan_add is the only function requiring the preparation
of a new VLAN entry.
To simplify things up, remove the mv88e6xxx_vtu_get wrapper and
explicit the VLAN lookup in _mv88e6xxx_port_vlan_add. This rework
also avoids programming the broadcast entries again when changing a
port's membership, e.g. from tagged to untagged.
At the same time, rename the helper using an old underscore convention.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read.
Explicit the call to mv88e6xxx_vtu_getnext in _mv88e6xxx_port_vlan_del
and the return value expected by switchdev in case of software VLANs.
At the same time, rename the helper using an old underscore convention.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_vtu_getnext is simple enough to call it directly in the
mv88e6xxx_port_db_load_purge function and explicit the return code
expected by switchdev for software VLANs when an hardware VLAN does
not exist.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_vtu_getnext interprets two members from the input
mv88e6xxx_vtu_entry structure: the (excluded) vid member to start
the iteration from, and the valid argument specifying whether the VID
must be written or not (only required once at the start of a loop).
Explicit the assignation of these two fields right before calling
mv88e6xxx_vtu_getnext, as it is done in the mv88e6xxx_vtu_get wrapper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
