The code for conversion between virtio_net_hdr and skb GSO info is
duplicated at several places. Let's put it to a common place to allow
reuse.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
As hypervior does not have the knowledge of guest network configuration, it's
better to ask guest to send gratuitous packets when needed.
This patch implements VIRTIO_NET_F_GUEST_ANNOUNCE feature: hypervisor would
notice the guest when it thinks it's time for guest to announce the link
presnece. Guest tests VIRTIO_NET_S_ANNOUNCE bit during config change interrupt
and woule send gratuitous packets through netif_notify_peers() and ack the
notification through ctrl vq.
We need to make sure the atomicy of read and ack in guest otherwise we may ack
more times than being notified. This is done through handling the whole config
change interrupt in an non-reentrant workqueue.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need for the guest to validate the checksum if it have been
validated by host nics. So this patch introduces a new flag -
VIRTIO_NET_HDR_F_DATA_VALID which is used to bypass the checksum
examing in guest. The backend (tap/macvtap) may set this flag when
met skbs with CHECKSUM_UNNECESSARY to save cpu utilization.
No feature negotiation is needed as old driver just ignore this flag.
Iperf shows 12%-30% performance improvement for UDP traffic. For TCP,
when gro is on no difference as it produces skb with partial
checksum. But when gro is disabled, 20% or even higher improvement
could be measured by netperf.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unclear to me if it's important, but it's obviously causing my
technical colleages some headaches and I'd hate such imprecision to
slow virtio adoption.
I've emailed this to all non-trivial contributors for approval, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
Acked-by: john cooper <john.cooper@redhat.com>
Acked-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Rusty,
commit 3ca4f5ca73
virtio: add virtio IDs file
moved all device IDs into a single file. While the change itself is
a very good one, it can break userspace applications. For example
if a userspace tool wanted to get the ID of virtio_net it used to
include virtio_net.h. This does no longer work, since virtio_net.h
does not include virtio_ids.h.
This patch moves all "#include <linux/virtio_ids.h>" from the C
files into the header files, making the header files compatible with
the old ones.
In addition, this patch exports virtio_ids.h to userspace.
CC: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Virtio IDs are spread all over the tree which makes assigning new IDs
bothersome. Putting them together should make the process less error-prone.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
I've been doing this for years, and akpm picked me up on it about 12
months ago. lguest partly serves as example code, so let's do it Right.
Also, remove two unused fields in struct vblk_info in the example launcher.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Qemu added support for a few extra RX modes that Linux doesn't
currently make use of. Sync the headers to maintain consistency.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_net.h uses the macro ETH_ALEN which is defined in linux/if_ether.h.
Discovered when hacking on virtio-over-pci patches.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering allows the hypervisor to drop packets from VLANs
that we're not a part of, further reducing the number of extraneous
packets recieved. This makes use of the VLAN virtqueue command class.
The CTRL_VLAN feature bit tells us whether the backend supports VLAN
filtering.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the MAC control virtqueue class to support a MAC
filter table. The filter table is managed by the hypervisor.
We consider the table to be available if the CTRL_RX feature
bit is set. We leave it to the hypervisor to manage the table
and enable promiscuous or all-multi mode as necessary depending
on the resources available to it.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the RX_MODE control virtqueue class to enable the
set_rx_mode netdev interface. This allows us to selectively
enable/disable promiscuous and allmulti mode so we don't see
packets we don't want. For now, we automatically enable these
as needed if additional unicast or multicast addresses are
requested.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used for RX mode, MAC filter table, VLAN filtering, etc...
The control transaction consists of one or more "out" sg entries and
one or more "in" sg entries. The first out entry contains a header
defining the class and command. Additional out entries may provide
data for the command. The last in entry provides a status response
back from the command.
Virtqueues typically run asynchronous, running a callback function
when there's data in the channel. We can't readily make use of this
in the command paths where we need to use this. Instead, we kick
the virtqueue and spin. The kick causes an I/O write, triggering an
immediate trap into the hypervisor.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make headers_check' warning:
usr/include/linux/virtio_net.h:28: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Allow the host to inform us that the link is down by adding
a VIRTIO_NET_F_STATUS which indicates that device status is
available in virtio_net config.
This is currently useful for simulating link down conditions
(e.g. using proposed qemu 'set_link' monitor command) but
would also be needed if we were to support device assignment
via virtio.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (added future masking)
Signed-off-by: David S. Miller <davem@davemloft.net>
If segmentation offload is enabled by the host, we currently allocate
maximum sized packet buffers and pass them to the host. This uses up
20 ring entries, allowing us to supply only 20 packet buffers to the
host with a 256 entry ring. This is a huge overhead when receiving
small packets, and is most keenly felt when receiving MTU sized
packets from off-host.
The VIRTIO_NET_F_MRG_RXBUF feature flag is set by hosts which support
using receive buffers which are smaller than the maximum packet size.
In order to transfer large packets to the guest, the host merges
together multiple receive buffers to form a larger logical buffer.
The number of merged buffers is returned to the guest via a field in
the virtio_net_hdr.
Make use of this support by supplying single page receive buffers to
the host. On receive, we extract the virtio_net_hdr, copy 128 bytes of
the payload to the skb's linear data buffer and adjust the fragment
offset to point to the remaining data. This ensures proper alignment
and allows us to not use any paged data for small packets. If the
payload occupies multiple pages, we simply append those pages as
fragments and free the associated skbs.
This scheme allows us to be efficient in our use of ring entries
while still supporting large packets. Benchmarking using netperf from
an external machine to a guest over a 10Gb/s network shows a 100%
improvement from ~1Gb/s to ~2Gb/s. With a local host->guest benchmark
with GSO disabled on the host side, throughput was seen to increase
from 700Mb/s to 1.7Gb/s.
Based on a patch from Herbert Xu.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use netdev_priv)
Signed-off-by: David S. Miller <davem@davemloft.net>
We want others to implement and use virtio, so it makes sense to BSD
license the non-__KERNEL__ parts of the headers to make this crystal
clear.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
So, we previously had a 'VIRTIO_NET_F_GSO' bit which meant that 'the
host can handle csum offload, and any TSO (v4&v6 incl ECN) or UFO
packets you might want to send. I thought this was good enough for
Linux, but it actually isn't, since we don't do UFO in software.
So, add separate feature bits for what the host can handle. Add
equivalent ones for the guest to say what it can handle, because LRO
is coming too (thanks Herbert!).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1) Turn GSO on virtio net into an all-or-nothing (keep checksumming
separate). Having multiple bits is a pain: if you can't support something
you should handle it in software, which is still a performance win.
2) Make VIRTIO_NET_HDR_GSO_ECN a flag in the header, so it can apply to
IPv6 or v4.
3) Rename VIRTIO_NET_F_NO_CSUM to VIRTIO_NET_F_CSUM (ie. means we do
checksumming).
4) Add csum and gso params to virtio_net to allow more testing.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's far easier to deal with packets if we don't have to parse the
packet to figure out the header length to know how much to pull into
the skb data. Add the field to the virtio_net_hdr struct (and fix the
spaces that somehow crept in there).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Previously we used a type/len pair within the config space, but this
seems overkill. We now simply define a structure which represents the
layout in the config space: the config space can now only be extended
at the end.
The main driver-visible changes:
1) We indicate what fields are present with an explicit feature bit.
2) Virtqueues are explicitly numbered, and not in the config space.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The network driver uses two virtqueues: one for input packets and one
for output packets. This has nice locking properties (ie. we don't do
any for recv vs send).
TODO:
1) Big packets.
2) Multi-client devices (maybe separate driver?).
3) Resolve freeing of old xmit skbs (Christian Borntraeger)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
