These values are never quite useful for dynamic allocations of the page
tables. Getting rid of them will help prevent later confusion.
v2: Updated to use unmap_and_free_pd functions.
v3: Updated gen8_ppgtt_free after teardown logic was removed.
v4: Rebase after s/page_tables/page_table/.
v5: Keep allocating all page directories in GEN8+ systems with less
than 4GB of memory. Updated gen6_for_all_pdes.
v6: Prevent (harmless) out of range access in gen6_for_all_pdes.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just so that I don't have to read about the batch pool on
systems that are not using it! Rather than using a newline between the
kernel clients and userspace clients, just distinguish the internal
allocations with a '[k]'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we use obj->active as a hint in many places throughout the code,
knowing its state in debugfs is extremely useful.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now with the trimmed memcpy before the command parser, we try to
allocate many different sizes of batches, predominantly one or two
pages. We can therefore speed up searching for a good sized batch by
keeping the objects of buckets of roughly the same size.
v2: Add a comment about bucket sizes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I woke up one morning and found 50k objects sitting in the batch pool
and every search seemed to iterate the entire list... Painting the
screen in oils would provide a more fluid display.
One issue with the current design is that we only check for retirements
on the current ring when preparing to submit a new batch. This means
that we can have thousands of "active" batches on another ring that we
have to walk over. The simplest way to avoid that is to split the pools
per ring and then our LRU execution ordering will also ensure that the
inactive buffers remain at the front.
v2: execlists still requires duplicate code.
v3: execlists requires more duplicate code
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With boosting for missed pageflips, we have a much stronger indication
of when we need to (temporarily) boost GPU frequency to ensure smooth
delivery of frames. So now only allow each client to perform one RPS boost
in each period of GPU activity due to stalling on results.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Occasionally it would be interesting to read some of the DPCD registers
for debug purposes, without having to resort to logging. Add an i915
specific i915_dpcd debugfs file for DP and eDP connectors to dump parts
of the DPCD. Currently the DPCD addresses to be dumped are statically
configured, and more can be added trivially.
The implementation also makes it relatively easy to add other i915 and
connector specific debugfs files in the future, as necessary.
This is currently i915 specific just because there's no generic way to
do AUX transactions given just a drm_connector. However it's all pretty
straightforward to port to other drivers.
v2: Add more DPCD registers to dump.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Count the number of requests in a ring for the user and show who
submitted them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we idle, we set the GPU frequency to the hardware minimum (not user
minimum). We introduce a new variable to distinguish between the
different roles, and to allow easy tuning of the idle frequency without
impacting over aspects of RPS. Setting the minimum frequency should be a
safety blanket as the pcu on the GPU should be power gating itself
anyway. However, in order for us to do set the absolute minimum
frequency, we need to relax a few of our assertions that we do not
exceed the user limits.
v2: Add idle_freq
v3: Init idle_freq for vlv and add a bunch of WARNs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Regressed by this commit:
commit 3455454e18ca3f92c565700539e744c620d8276b
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Mar 3 15:21:56 2015 +0200
drm/i915: Add a for_each_intel_connector macro
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added support for SKL in the i915_frequency_info debugfs function
v2:
- corrected the handling of reqf (Damien)
- Reorderd the platform check for cagf (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Static analysis was complaining that a path existed where we could use
stat[] uninitialized. Fix this by simplifying the logic to exit early if
PSR isn't supported.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Collect the currently enabled counts of slice, subslice, and
execution units using the power gate control ack message
registers specific to Cherryview.
Slice/subslice/EU info and hardware status can now be
determined for CHV, so allow the debugfs SSEU status dump
to proceed for CHV devices.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently, this has never worked reliably and is currently disabled. Also, the
gains are not particularly impressive. Thus rather than try to keep unused code
from decaying and having to update it for other driver changes, it was decided
to simply remove it.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding a debugfs entry to determine if DRRS is supported or not
V2: [By Ram]: Following details about the active crtc will be filled
in seq-file of the debugfs
1. Encoder output type
2. DRRS Support on this CRTC
3. DRRS current state
4. Current Vrefresh
Format is as follows:
CRTC 1: Output: eDP, DRRS Supported: Yes (Seamless), DRRS_State: DRRS_HIGH_RR, Vrefresh: 60
CRTC 2: Output: HDMI, DRRS Supported : No, VBT DRRS_type: Seamless
CRTC 1: Output: eDP, DRRS Supported: Yes (Seamless), DRRS_State: DRRS_LOW_RR, Vrefresh: 40
CRTC 2: Output: HDMI, DRRS Supported : No, VBT DRRS_type: Seamless
V3: [By Ram]: Readability is improved.
Another error case is covered [Daniel]
V4: [By Ram]: Current status of the Idleness DRRS along with
the Front buffer bits are added to the debugfs. [Rodrigo]
V5: [By Ram]: Rephrased to make it easy to understand.
And format is modified. [Rodrigo]
V6: [By Ram]: Modeset mutex are acquired for each crtc along with
renaming the Idleness detection states [Daniel]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: dump full busy_frontbuffer_bits and remove the dubios
computed logical state of DRRS - debugfs is about what is fact,
developers should reach their own conclusion when debugging issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have similar macros for crtcs and encoders, and the pattern happens
often enough to justify the macro.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implicit usage of local variables in macros isn't exactly the greatest
thing in the world, especially when that variable is the drm device and
we want to move towards a broader use of the i915 device structure.
Let's make for_each_plane() take dev_priv as its first argument then.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor size fields in intel_crtc just duplicate the data from
cursor->state.crtc_{w,h} so we don't need them any more. Worse, their
use in the watermark code actually introduces a subtle bug since they
don't get updated to mirror the state values until the plane commit
stage, which is *after* we've already used them to calculate new
watermark values. This happens because we had to move watermark updates
slightly earlier (outside vblank evasion) in commit
commit 32b7eeec4d
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Wed Dec 24 07:59:06 2014 -0800
drm/i915: Refactor work that can sleep out of commit (v7)
Dropping the intel_crtc fields and just using the state values (which
are properly updated by the time watermark updates happen) should solve
the problem.
Aside from the actual removal of the struct fields (which are formatted
in a way that I couldn't figure out how to match in Coccinelle), the
rest of this patch was generated via the following semantic patch:
// Drop assignment
@@
struct intel_crtc *C;
struct drm_plane_state S;
@@
(
- C->cursor_width = S.crtc_w;
|
- C->cursor_height = S.crtc_h;
)
// Replace usage
@@
struct intel_crtc *C;
expression E;
@@
(
- C->cursor_width
+ C->base.cursor->state->crtc_w
|
- C->cursor_height
+ C->base.cursor->state->crtc_h
|
- to_intel_crtc(E)->cursor_width
+ E->cursor->state->crtc_w
|
- to_intel_crtc(E)->cursor_height
+ E->cursor->state->crtc_h
)
v2: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89346
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
- Y tiling support for scanout from Tvrtko&Damien
- Remove more UMS support
- some small prep patches for OLR removal from John Harrison
- first few patches for dynamic pagetable allocation from Ben Widawsky, rebased
by tons of other people
- DRRS support patches (Sonika&Vandana)
- fbc patches from Paulo
- make sure our vblank callbacks aren't called when the pipes are off
- various patches all over
* tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20150227
drm/i915: Clarify obj->map_and_fenceable
drm/i915/skl: Allow Y (and Yf) frame buffer creation
drm/i915/skl: Update watermarks for Y tiling
drm/i915/skl: Updated watermark programming
drm/i915/skl: Adjust get_plane_config() to support Yb/Yf tiling
drm/i915/skl: Teach pin_and_fence_fb_obj() about Y tiling constraints
drm/i915/skl: Adjust intel_fb_align_height() for Yb/Yf tiling
drm/i915/skl: Allow scanning out Y and Yf fbs
drm/i915/skl: Add new displayable tiling formats
drm/i915: Remove DRIVER_MODESET checks from modeset code
drm/i915: Remove regfile code&data for UMS suspend/resume
drm/i915: Remove DRIVER_MODESET checks from gem code
drm/i915: Remove DRIVER_MODESET checks in the gpu reset code
drm/i915: Remove DRIVER_MODESET checks from suspend/resume code
drm/i915: Remove DRIVER_MODESET checks in load/unload/close code
drm/i915: fix a printk format
drm/i915: Add media rc6 residency file to sysfs
drm/i915: Add missing description to parameter in alloc_pt_range
drm/i915: Removed the read of RP_STATE_CAP from sysfs/debugfs functions
...
- use the atomic helpers for plane_upate/disable hooks (Matt Roper)
- refactor the initial plane config code (Damien)
- ppgtt prep patches for dynamic pagetable alloc (Ben Widawsky, reworked and
rebased by a lot of other people)
- framebuffer modifier support from Tvrtko Ursulin, drm core code from Rob Clark
- piles of workaround patches for skl from Damien and Nick Hoath
- vGPU support for xengt on the client side (Yu Zhang)
- and the usual smaller things all over
* tag 'drm-intel-next-2015-02-14' of git://anongit.freedesktop.org/drm-intel: (88 commits)
drm/i915: Update DRIVER_DATE to 20150214
drm/i915: Remove references to previously removed UMS config option
drm/i915/skl: Use a LRI for WaDisableDgMirrorFixInHalfSliceChicken5
drm/i915/skl: Fix always true comparison in a revision id check
drm/i915/skl: Implement WaEnableLbsSlaRetryTimerDecrement
drm/i915/skl: Implement WaSetDisablePixMaskCammingAndRhwoInCommonSliceChicken
drm/i915: Add process identifier to requests
drm/i915/skl: Implement WaBarrierPerformanceFixDisable
drm/i915/skl: Implement WaCcsTlbPrefetchDisable:skl
drm/i915/skl: Implement WaDisableChickenBitTSGBarrierAckForFFSliceCS
drm/i915/skl: Implement WaDisableHDCInvalidation
drm/i915/skl: Implement WaDisableLSQCROPERFforOCL
drm/i915/skl: Implement WaDisablePartialResolveInVc
drm/i915/skl: Introduce a SKL specific init_workarounds()
drm/i915/skl: Document that we implement WaRsClearFWBitsAtReset
drm/i915/skl: Implement WaSetGAPSunitClckGateDisable
drm/i915/skl: Make the init clock gating function skylake specific
drm/i915/skl: Provide a gen9 specific init_render_ring()
drm/i915/skl: Document the WM read latency W/A with its name
drm/i915/skl: Also detect eDRAM on SKL
...
The current implementation is limited by the number of addresses that
fit into an unsigned long. This causes problems on 32-bit Tegra where
unsigned long is 32-bit but drm_mm is used to manage an IOVA space of
4 GiB. Given the 32-bit limitation, the range is limited to 4 GiB - 1
(or 4 GiB - 4 KiB for page granularity).
This commit changes the start and size of the range to be an unsigned
64-bit integer, thus allowing much larger ranges to be supported.
[airlied: fix i915 warnings and coloring callback]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixupo
The frequency values(Rp0, Rp1, Rpn) reported by RP_STATE_CAP register
are stored, initially by the Driver, inside the dev_priv->rps structure.
Since these values are expected to remain same throughout, there is no real
need to read this register, on dynamic basis, from certain debugfs/sysfs
functions and the values can be instead retrieved from the dev_priv->rps
structure when needed.
For the i915_frequency_info debugfs interface, the frequency values from the
RP_STATE_CAP register only should be used, to indicate the actual Hw state,
since it is principally used for the debugging purpose.
v2: Reverted the changes in i915_frequency_info function, to continue report
back the frequency values, as per the actual Hw state (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the remaining members over to the new page table structures.
This can be squashed with the previous commit if desire. The reasoning
is the same as that patch. I simply felt it is easier to review if split.
v2: In lrc: s/ppgtt->pd_dma_addr[i]/ppgtt->pdp.page_directory[i].daddr/
v3: Rebase.
v4: Rebased after s/page_tables/page_table/.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Static checkers complain that we should probably add curly braces
because, from the indenting, it looks like seq_printf() should be inside
the list_for_each_entry() loop. But the code is actually correct, it's
just the indenting which is off.
Besides fixing the indenting on seq_printf(), I did add curly braces,
because generally mult-line indents should have curly braces to make
them more readable.
The unintended indent was left behind and not unindented in
commit d7f46fc4e7
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Fri Dec 6 14:10:55 2013 -0800
drm/i915: Make pin count per VMA
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new section to the 'i915_sseu_status' debugfs entry to
report the currently enabled counts of slice, subslice, and
execution units on the device. The count of enabled subslice
per slice represents the most enabled subslice on any one
slice for devices where imbalances may exist. Similarly, the
count of enabled EU per subslice represents the most enabled
EU on any one subslice.
Collect this device status for Skylake by reading the Gen9
power gate control ack message registers. Power gate control
operates on EU in pairs, therefore our reported counts of
enabled EU can be overestimated by one for each pair in which
one EU is fused-off.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read fuse registers to determine the available slice total,
subslice total, subslice per slice, EU total, and EU per subslice
counts of the SKL device. The EU per subslice attribute is more
precisely defined as the maximum EU available on any one subslice,
since available EU counts may vary across subslices due to fusing.
Set flags indicating the SKL device's slice/subslice/EU (SSEU)
power gating capability. Make all values available via debugfs
entry 'i915_sseu_status'.
v2: Several small clean-ups suggested by Damien. Most notably,
used smaller types for the new device info fields to reduce
memory usage and improved the clarity/readability of the
method used to extract attribute values from the fuse
registers.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Where possible right now. Just a small step towards nirvana ...
v2: git add. Uggh. Noticed by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Replace the valleyview_set_rps() and gen6_set_rps() calls with
intel_set_rps() which itself does the IS_VALLEYVIEW() check. The
code becomes simpler since the callers don't have to do this check
themselves.
Most of the change was performe with the following semantic patch:
@@
expression E1, E2, E3;
@@
- if (IS_VALLEYVIEW(E1)) {
- valleyview_set_rps(E2, E3);
- } else {
- gen6_set_rps(E2, E3);
- }
+ intel_set_rps(E2, E3);
Adding intel_set_rps() and making valleyview_set_rps() and gen6_set_rps()
static was done manually. Also valleyview_set_rps() had to be moved a
bit avoid a forward declaration.
v2: Use a less greedy semantic patch
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We read the coherent current seqno and actual head from ring.
For hardware access we need to take runtime_pm reference.
Get hardware specific values with runtime reference held
and print them first to emphasize hw state vs bookkeepping.
v2: Reorder output according to hw access (Chris)
remove superfluous locking (Daniel)
Testcase: igt/pm_rpm/debugfs-read
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88910
Tested-by: Ding Heng <hengx.ding@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now when we declare gpu errors only through our own dedicated
hangcheck workqueue there is no need to have a separate workqueue
for handling the resetting and waking up the clients as the deadlock
concerns are no more.
The only exception is i915_debugfs::i915_set_wedged, which triggers
error handling through process context. However as this is only used through
test harness it is responsibility for test harness not to introduce hangs
through both debug interface and through hangcheck mechanism at the same time.
Remove gpu_error.work and let the hangcheck work do the tasks it used to.
v2: Add a big warning sign into i915_debugfs::i915_set_wedged (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have had %x and %u intermixed. Bring everything in line and
use %x
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For example,
/sys/kernel/debug/dri/0/i915_hangcheck_info:
Hangcheck active, fires in 15887800ms
render ring:
seqno = -4059 [current -583]
action = 2
score = 0
ACTHD = 1ee8 [current 21f980]
max ACTHD = 0
v2: Include expiration ETA. Can anyone spot a problem?
v3: Convert for workqueued hangcheck (Mika)
v4: Print seqnos as unsigned ints (Ville)
v5: Print seqnos as hex (Chris)
Tested-By: PRC QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com) (v2)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace all the vlv_gpu_freq(), vlv_freq_opcode(),
*GT_FREQUENCY_MULTIPLIER, and /GT_FREQUENCY_MULTIPLIER instances
with intel_gpu_freq() and intel_freq_opcode() calls.
Most of the change was performed with the following semantic patch:
@@
expression E;
@@
(
- E * GT_FREQUENCY_MULTIPLIER
+ intel_gpu_freq(dev_priv, E)
|
- E *= GT_FREQUENCY_MULTIPLIER
+ E = intel_gpu_freq(dev_priv, E)
|
- E /= GT_FREQUENCY_MULTIPLIER
+ E = intel_freq_opcode(dev_priv, E)
|
- do_div(E, GT_FREQUENCY_MULTIPLIER)
+ E = intel_freq_opcode(dev_priv, E)
)
@@
expression E1, E2;
@@
(
- vlv_gpu_freq(E1, E2)
+ intel_gpu_freq(E1, E2)
|
- vlv_freq_opcode(E1, E2)
+ intel_freq_opcode(E1, E2)
)
@@
expression E1, E2, E3, E4;
@@
(
- if (IS_VALLEYVIEW(E1)) {
- E2 = intel_gpu_freq(E3, E4);
- } else {
- E2 = intel_gpu_freq(E3, E4);
- }
+ E2 = intel_gpu_freq(E3, E4);
|
- if (IS_VALLEYVIEW(E1)) {
- E2 = intel_freq_opcode(E3, E4);
- } else {
- E2 = intel_freq_opcode(E3, E4);
- }
+ E2 = intel_freq_opcode(E3, E4);
)
One hunk was manually undone as intel_gpu_freq() ended up
calling itself. Supposedly it would be possible to exclude
certain functions via !=~, but I couldn't get that to work.
Also the removal of vlv_gpu_freq() and vlv_opcode_freq() compat
wrappers was done manually.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding new power doamins for AUX controllers
v2: Added new power domains in power_domain_str per Imre's comment
v3: Added AUX power domains to older platforms
v4: Rebase on top of POWER_DOMAIN_PLLS.
v5: Modified to address review comments from Imre
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are multiple forcewake domains in newer architectures.
Rename 'i915_gen6_forcewake_count_info' debugfs entry to
'i915_forcewake_domains' to reflect this.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have multiple forcewake domains now on recent gens. Change the
function naming to reflect this.
v2: More verbose names (Chris)
v3: Rebase
v4: Rebase
v5: Add documentation for forcewake_get/put
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we now have forcewake domains, take advantage of it
by putting the differences in gen fw handling in data rather
than in code.
In past we have opencoded this quite extensively as the fw handling
is in the fast path. There has also been a lot of cargo-culted
copy'n'pasting from older gens to newer ones.
Now when the releasing of the forcewake is done by deferred timer,
it gives chance to consolidate more. Due to the frequency of actual hw
access being significantly less.
Take advantage of this and generalize the fw handling code
as much as possible. But we still aim to keep the forcewake sequence
particularities for each gen intact. So the access pattern
to fw engines should remain the same.
v2: - s/old_ack/clear_ack (Chris)
- s/post_read/posting_read (Chris)
- less polite commit msg (Chris)
v3: - rebase
- check and clear wake_count in init
v4: - fix posting reads for gen8 (PRTS)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a structure to track the individual forcewake domains and use
that to eliminate duplicate logic.
v2: - Rebase on latest dinq (Mika)
- for_each_fw_domain macro (Mika)
- Handle reset atomically, keeping the timer running (Mika)
- for_each_fw_domain parameter ordering (Chris)
- defer timer on new register access (Mika)
v3: - Fix forcewake_reset/get race by waiting pending timers
v4: - cond_resched and verbose warning on timer deletion (Chris)
- need to run pending timers manually on reset
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On user forcewake access, assert that runtime pm reference is held.
Fix and cleanup the callsites accordingly.
v2: Remove intel_runtime_pm_get() rebasehap (Deepak)
v3: use drivers own runtime state tracking as pm_runtime_active()
will return wrong results when we are in resume callchain (Mika)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move all remaining elements that were unique to execlists queue items
in to the associated request.
Issue: VIZ-4274
v2: Rebase. Fixed issue of overzealous freeing of request.
v3: Removed re-addition of cleanup work queue (found by Daniel Vetter)
v4: Rebase.
v5: Actual removal of intel_ctx_submit_request. Update both tail and postfix
pointer in __i915_add_request (found by Thomas Daniel)
v6: Removed unrelated changes
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Reformat comment with strange linebreaks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Where there were duplicate variables for the tail, context and ring (engine)
in the gem request and the execlist queue item, use the one from the request
and remove the duplicate from the execlist queue item.
Issue: VIZ-4274
v1: Rebase
v2: Fixed build issues. Keep separate postfix & tail pointers as these are
used in different ways. Reinserted missing full tail pointer update.
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.
@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member
v2: Clarify manual changes by splitting them into another patch. (Matt)
Improve cocci script to generate even more of the changes. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is useful to know at debug time if we are keeping main link on.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds a small module for managing a pool of batch buffers.
The only current use case is for the command parser, as described
in the kerneldoc in the patch. The code is simple, but separating
it out makes it easier to change the underlying algorithms and to
extend to future use cases should they arise.
The interface is simple: init to create an empty pool, fini to
clean it up, get to obtain a new buffer. Note that all buffers are
expected to be inactive before cleaning up the pool.
Locking is currently based on the caller holding the struct_mutex.
We already do that in the places where we will use the batch pool
for the command parser.
v2:
- s/BUG_ON/WARN_ON/ for locking assertions
- Remove the cap on pool size
- Switch from alloc/free to init/fini
v3:
- Idiomatic looping structure in _fini
- Correct handling of purged objects
- Don't return a buffer that's too much larger than needed
v4:
- Rebased to latest -nightly
v5:
- Remove _put() function and clean up comments to match
v6:
- Move purged check inside the loop (danvet, from v4 1/7 feedback)
v7:
- Use single list instead of two. (Chris W)
- s/active_list/cache_list
- Squashed in debug patches (Chris W)
drm/i915: Add a batch pool debugfs file
It provides some useful information about the buffers in
the global command parser batch pool.
v2: rebase on global pool instead of per-ring pools
v3: rebase
drm/i915: Add batch pool details to i915_gem_objects debugfs
To better account for the potentially large memory consumption
of the batch pool.
v8:
- Keep cache in LRU order (danvet, from v6 1/5 feedback)
Issue: VIZ-4719
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-By: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Things like reliable GGTT mappings and mirrored 2d-on-3d display will need
to map objects into the same address space multiple times.
Added a GGTT view concept and linked it with the VMA to distinguish between
multiple instances per address space.
New objects and GEM functions which do not take this new view as a parameter
assume the default of zero (I915_GGTT_VIEW_NORMAL) which preserves the
previous behaviour.
This now means that objects can have multiple VMA entries so the code which
assumed there will only be one also had to be modified.
Alternative GGTT views are supposed to borrow DMA addresses from obj->pages
which is DMA mapped on first VMA instantiation and unmapped on the last one
going away.
v2:
* Removed per view special casing in i915_gem_ggtt_prepare /
finish_object in favour of creating and destroying DMA mappings
on first VMA instantiation and last VMA destruction. (Daniel Vetter)
* Simplified i915_vma_unbind which does not need to count the GGTT views.
(Daniel Vetter)
* Also moved obj->map_and_fenceable reset under the same check.
* Checkpatch cleanups.
v3:
* Only retire objects once the last VMA is unbound.
v4:
* Keep scatter-gather table for alternative views persistent for the
lifetime of the VMA.
* Propagate binding errors to callers and handle appropriately.
v5:
* Explicitly look for normal GGTT view in i915_gem_obj_bound to align
usage in i915_gem_object_ggtt_unpin. (Michel Thierry)
* Change to single if statement in i915_gem_obj_to_ggtt. (Michel Thierry)
* Removed stray semi-colon in i915_gem_object_set_cache_level.
For: VIZ-4544
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Drop hunk from i915_gem_shrink since it's just prettification
but upsets a __must_check warning.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Faster feedback to errors is always better. This is inspired by the
addition to WARN_ONs to mask/enable helpers for registers to make sure
callers have the arguments ordered correctly: Pretty much always the
arguments are static.
We use WARN_ON(1) a lot in default switch statements though where we
should always handle all cases. So add a new macro specifically for
that.
The idea to use __builtin_constant_p is from Chris Wilson.
v2: Use the ({}) gcc-ism to avoid the static inline, suggested by
Dave. My first attempt used __cond as the temp var, which is the same
used by BUILD_BUG_ON, but with inverted sense. Hilarity ensued, so
sprinkle i915 into the name.
Also use a temporary variable to only evaluate the condition once,
suggested by Damien.
v3: It's crazy but apparently 32bit gcc can't compile out the
BUILD_BUG_ON in a lot of cases and just falls over. I have no idea
why, but until clue grows just disable this nifty idea on 32bit
builds. Reported by 0-day builder.
v4: Got it all wrong, apparently its the gcc version. We need 4.9+.
Now reported by Imre.
v5: Chris suggested to add the case to MISSING_CASE for speedier
debug.
v6: Even some gcc 4.9 versions don't see through the maze, so give up
for now. Keep the skeleton and MISSING_CASE stuff though.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Stupid userspace (there is no evil userspace in debugfs by assumption)
might provoke a leak since we allocate the new array without holding
any locks. Drop in an unconditional kfree to deal with this - kfree
can handle NULL.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Currently i915_pipe_crc_read() will drop pipe_crc->lock for the entire
duration of the copy_to_user() loop, which means it'll access
pipe_crc->entries without any protection. If another thread sneaks in
and frees pipe_crc->entries the code will oops.
Reorganize the code to hold the lock around everything except
copy_to_user(). After the copy the lock is reacquired and the the number
of available entries is rechecked.
Since this is a debug feature simplify the error handling a bit by
consuming the crc entry even if copy_to_user() would fail.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
