i.MX7S does NOT support CPU frequency scaling, so no
need to specify the CPU regulator supply.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch configures the board to output UART6 to the mikroBus.
The NXP WaRP7 board can route UART6 to the mikroBus, where an RS232
click board can be plugged in to get an additional serial port.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
mmc1: new MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
On imx7s-warp the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
With this change HS200 error is gone and another benefit is that the
card can operate in DDR52 mode now:
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
Suggested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7 has two iomux controllers. the iomuxc and the iomuxc_lpsr.
In a board dts we have to make sure that both controllers are supplied
with the correct pins. It's way too easy to do this wrong since only
a look into the reference manual can reveal which pins belong to which
controller. To make this clearer add "LPSR" to the pin names which
belong to the LPSR controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog pin is controlled by the iomuxc_lpsr, not the regular
iomux, so move it there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
WaRP7 has a BCM43430 Bluetooth chip.
Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7s-warpd has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Warp7 has a BCM43430 Wifi chip connected to the USDHC1 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
warp7 has a sgtl5000 audio codec.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for MPL3115 NXP pressure sensor.
Tested by reading temperature and pressure:
$ cat /sys/bus/iio/devices/iio:device0/in_temp_raw
$ cat /sys/bus/iio/devices/iio:device0/in_pressure_raw
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
