net/sch_generic.h does not need to be included, remove it.
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Th referenced change added an extra hw reset to rtl8169_net_suspend()
what makes WoL fail on few chip versions. Therefore skip the extra
reset if we're going down and WoL is enabled.
In rtl_shutdown() rtl8169_hw_reset() is called by rtl8169_net_suspend()
already if needed, therefore avoid issues issue by removing the extra
call. The fix was tested on a system with RTL8168g.
Meanwhile rtl8169_hw_reset() does more than a hw reset and should be
renamed. But that's net-next material.
Fixes: 8ac8e8c64b ("r8169: make rtl8169_down central chip quiesce function")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is return PTR_ERR(NULL) which is zero or success. We should
return -ENOMEM instead.
Fixes: 94abdad697 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two issues with XDP:
1. If the XDP verdict is XDP_ABORTED we break the loop, which results in
us handling one buffer per napi cycle instead of the total budget
(usually 64). To overcome this simply change the xdp_verdict check to
!= XDP_PASS. When the verdict is XDP_PASS, the skb is not expected to
be NULL.
2. Update the residual budget for XDP_DROP and XDP_ABORTED, since
packets are handled in these cases.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending very high packet rate, the XDP tx queues can get full and
start dropping packets. In this case we don't free the pages which
results in ena driver draining the system memory.
Fix:
Simply free the pages when necessary.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_uld_in_use() is used only by cxgb4_ktls_det_feature() which
is under CONFIG_CHELSIO_TLS_DEVICE macro.
Fixes: a3ac249a1a ("cxgb4/chcr: Enable ktls settings at run time")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
add support to change TX/RX queue number with "ethtool -L combined".
V5 -> V6: remove check for carrier in hinic_xmit_frame
V4 -> V5: change time zone in patch header
V3 -> V4: update date in patch header
V2 -> V3: remove check for zero channels->combined_count
V1 -> V2: update commit message("ethtool -L" to "ethtool -L combined")
V0 -> V1: remove check for channels->tx_count/rx_count/other_count
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in
the struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
* Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
* Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
* Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
* Fix wrong compatible binding in the qcom driver (Ansuel Smith).
* Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
* Add r8a7742 SoC support to the dt cpufreq driver (Lad Prabhakar).
- Update cpuidle core and drivers:
* Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
* Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
* Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver
and remove an unused local MSR definition from it (Jacob Pan,
Sumeet Pawnikar).
- Update devfreq core and drivers:
* Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
* Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
* Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei).
-----BEGIN PGP SIGNATURE-----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=APdj
-----END PGP SIGNATURE-----
Merge tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the system-wide PM driver flags, make runtime switching
of cpuidle governors easier, improve the user space hibernation
interface code, add intel-speed-select interface documentation, add
more debug messages to the ACPI code handling suspend to idle, update
the cpufreq core and drivers, fix a minor issue in the cpuidle core
and update two cpuidle drivers, improve the PM-runtime framework,
update the Intel RAPL power capping driver, update devfreq core and
drivers, and clean up the cpupower utility.
Specifics:
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in the
struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
- Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
- Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
- Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
- Fix wrong compatible binding in the qcom driver (Ansuel Smith).
- Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
- Add r8a7742 SoC support to the dt cpufreq driver (Lad
Prabhakar).
- Update cpuidle core and drivers:
- Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
- Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
- Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver and
remove an unused local MSR definition from it (Jacob Pan, Sumeet
Pawnikar).
- Update devfreq core and drivers:
- Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
- Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
- Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei)"
* tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (51 commits)
cpuidle: Fix three reference count leaks
PM: runtime: Replace pm_runtime_callbacks_present()
PM / devfreq: Use lockdep asserts instead of manual checks for locked mutex
PM / devfreq: imx-bus: Fix inconsistent IS_ERR and PTR_ERR
PM / devfreq: Replace strncpy with strscpy
PM / devfreq: imx: Register interconnect device
PM / devfreq: Add generic imx bus scaling driver
PM / devfreq: tegra30: Delete an error message in tegra_devfreq_probe()
PM / devfreq: tegra30: Make CPUFreq notifier to take into account boosting
PM: hibernate: Restrict writes to the resume device
PM: runtime: clk: Fix clk_pm_runtime_get() error path
cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver
ACPI: EC: PM: s2idle: Extend GPE dispatching debug message
ACPI: PM: s2idle: Print type of wakeup debug messages
powercap: RAPL: remove unused local MSR define
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
Documentation: admin-guide: pm: Document intel-speed-select
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
Documentation: ABI: make current_governer_ro as a candidate for removal
...
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-06-01
The following pull-request contains BPF updates for your *net-next* tree.
We've added 55 non-merge commits during the last 1 day(s) which contain
a total of 91 files changed, 4986 insertions(+), 463 deletions(-).
The main changes are:
1) Add rx_queue_mapping to bpf_sock from Amritha.
2) Add BPF ring buffer, from Andrii.
3) Attach and run programs through devmap, from David.
4) Allow SO_BINDTODEVICE opt in bpf_setsockopt, from Ferenc.
5) link based flow_dissector, from Jakub.
6) Use tracing helpers for lsm programs, from Jiri.
7) Several sk_msg fixes and extensions, from John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports a warning at efx_ef10_try_update_nic_stats_vf()
warning: context imbalance in efx_ef10_try_update_nic_stats_vf()
- unexpected unlock
The root cause is the missing annotation at
efx_ef10_try_update_nic_stats_vf()
Add the missing _must_hold(&efx->stats_lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current design enables ktls setting from start, which is not
efficient. Now the feature will be enabled when user demands
TLS offload on any interface.
v1->v2:
- taking ULD module refcount till any single connection exists.
- taking rtnl_lock() before clearing tls_devops.
v2->v3:
- cxgb4 is now registering to tlsdev_ops.
- module refcount inc/dec in chcr.
- refcount is only for connections.
- removed new code from cxgb_set_feature().
v3->v4:
- fixed warning message.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-31
This series contains updates to the ice driver only.
Brett modifies the driver to allow users to clear a VF's
administratively set MAC address on the PF. Fixes the driver to
recognize an existing VLAN tag when DMAC/SMAC is enabled in a packet.
Fixes an issue, so that VF's are reset after any VF port VLAN
modifications are made on the PF. Made sure the register QRXFLXP_CNTXT
is cleared before writing a new value to ensure the previous value is
not passed forward. Updates the PF to allow the VF to request a reset
as soon as it has been initialized. Fixes an issue to ensure when a VSI
is created, it uses the current coalesce value, not the default value.
Paul allows untrusted VF's to add 16 filters.
Dan increases the timeout needed after a PFR to allow ample time for
package download.
Chinh adjust the define value for the number of PHY speeds we currently
support. Changes the driver to ignore EMODE error when configuring the
PHY.
Jesse fixes an issue which was preventing a user from configuring the
interface before bringing it up.
Henry fixes the logic for adding back perfect flows after flow director
filter does a deletion.
Bruce fixes line wrappings to make it more consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Leave congestion group taildrop enabled for all traffic classes
when PFC is enabled. Notification threshold is low enough such
that it will be hit first and this also ensures that FQs on
traffic classes which are not PFC enabled won't drain the buffer
pool.
FQ taildrop threshold is kept disabled as long as any form of
flow control is on. Since FQ taildrop works with bytes, not number
of frames, we can't guarantee it will not interfere with the
congestion notification mechanism for all frame sizes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.
Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).
Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.
The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have congestion group taildrop configured at all
times, we can afford to increase the frame queue taildrop
threshold; this will ensure a better response when receiving
bursts of large-sized frames.
Also decouple the buffer pool count from the Rx FQ taildrop
threshold, as above change would increase it too much. Instead,
keep the old count as a hardcoded value.
With the new limits, we try to ensure that:
* we allow enough leeway for large frame bursts (by buffering
enough of them in queues to avoid heavy dropping in case of
bursty traffic, but when overall ingress bandwidth is manageable)
* allow pending frames to be evenly spread between ingress FQs,
regardless of frame size
* avoid dropping frames due to the buffer pool being empty; this
is not a bad behaviour per se, but system overall response is
more linear and predictable when frames are dropped at frame
queue/group level.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The increase in number of ingress frame queues means we now risk
depleting the buffer pool before the FQ taildrop kicks in.
Congestion group taildrop allows us to control the number of frames that
can accumulate on a group of Rx frame queues belonging to the same
traffic class. This setting coexists with the frame queue based
taildrop: whichever limit gets hit first triggers the frame drop.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add convenient helper functions that determines whether Rx/Tx pause
frames are enabled based on link state flags received from firmware.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware reserves for each DPNI a number of RX frame queues
equal to the number of configured flows x number of configured
traffic classes.
Current driver configuration directs all incoming traffic to
FQs corresponding to TC0, leaving all other priority levels unused.
Start adding support for multiple ingress traffic classes, by
configuring the FQs associated with all priority levels, not just
TC0. All settings that are per-TC, such as those related to
hashing and flow steering, are also updated.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.
New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in
other typical Linux drivers. The usage of phylib allows to
specify fixed-link parameters in the device tree.
. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).
Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing
as soon as the Corona measures allow this.
. All review findings of Andrew Lunn are included
Example:
--------
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have an Rx listener function for exception traps that marks
received skbs with 'offload_fwd_mark' and injects them to the kernel's
Rx path. The marking is done because all these exceptions occur during
L3 forwarding, after the packets were potentially flooded at L2.
A subsequent patch will add support for control traps. Packets received
via some of these control traps need different handling:
1. Packets might not need to be marked with 'offload_fwd_mark'. For
example, if packet was trapped before L2 forwarding
2. Packets might not need to be injected to the kernel's Rx path. For
example, sampled packets are reported to user space via the psample
module
Factor out a common Rx listener function that only reports trapped
packets to devlink. Call it from mlxsw_sp_rx_no_mark_listener() and
mlxsw_sp_rx_mark_listener() that will inject the packets to the kernel's
Rx path, without and with the marking, respectively.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: Liu Xiang <liuxiang_1999@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The removal of mips_swiotlb_ops exposed a problem in octeon_mgmt Ethernet
driver. mips_swiotlb_ops had an mb() after most of the operations and the
removal of the ops had broken the receive functionality of the driver.
My code inspection has shown no other places except
octeon_mgmt_rx_fill_ring() where an explicit barrier would be obviously
missing. The latter function however has to make sure that "ringing the
bell" doesn't happen before RX ring entry is really written.
The patch has been successfully tested on Octeon II.
Fixes: a999933db9 ("MIPS: remove mips_swiotlb_ops")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
No need for mlx5e_rep_indr_clean_block_privs() since flow_block_cb_free()
already releases the internal mapping via ->release callback, which in
this case is mlx5e_rep_indr_tc_block_unbind().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shrink the code visually by replacing regmap_update_bits() with
appropriate regmap bit operations where applicable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller doesn't care about the error codes, they only check for zero
vs non-zero. Still, it's better to preserve the negative error codes
from alloc_uld_rxqs() instead of changing it to 1. We can also return
directly if there is a failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic was missing for adding back perfect flows after flow director
filter delete. The code now adds perfect flows into the HW tables after
filter delete.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VSI is built (i.e. reset, set channels, etc.)
the coalesce settings will be preserved in most cases. However, when the
number of q_vectors are increased the settings for the new q_vectors
will be set to the driver defaults of AIM on, Rx/Tx ITR 50, and INTRL 0.
This is causing issues with how the ethtool layer gets the current
coalesce settings since it only uses q_vector 0. So, assume that the user
set the coalesce settings globally (i.e. ethtool -C eth0) and use q_vector
0's settings for all of the new q_vectors.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, cuddle multiple lines of function signatures to be
consistent throughout the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VF driver has the ability to request reset via VIRTCHNL_OP_RESET_VF.
This is a required step in VF driver load. Currently, the PF is only
allowing a VF to request reset using this method after the VF has
already communicated resources via VIRTCHNL_OP_GET_VF_RESOURCES.
However, this is incorrect because the VF can request reset before
requesting resources. Fix this by allowing the VF to request a reset
once it has been initialized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver prevents a user from doing
modprobe ice
ethtool -L eth0 combined 5
ip link set eth0 up
The ethtool command fails, because the driver is checking to see if the
interface is down before allowing the get_channels to proceed (even for
a set_channels).
Remove this check and allow the user to configure the interface
before bringing it up, which is a much better usability case.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always clear the previous value in QRXFLXP_CNTXT before writing a new
value. This will make it so re-used queues will not accidentally take the
previously configured settings.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF is modifying the VF's port VLAN on the fly when
configured via iproute. This is okay for most cases, but if the VF
already has guest VLANs configured the PF has to remove all of those
filters so only VLAN tagged traffic that matches the port VLAN will
pass. Instead of adding functionality to track which guest VLANs have
been added, just reset the VF each time port VLAN parameters are
modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As currently, we are supporting only 5 PHY_SPEEDs for phy_type_high.
Thus, we should adjust the value of ICE_PHY_TYPE_HIGH_MAX_INDEX to 5.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To allow for resets during package download, increase the timeout period
after performing a PFR. The time waited is the global config lock
timeout plus the normal PFSWR timeout.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver does not recognize when there is an 802.1AD VLAN
tag right after the dmac/smac (outermost VLAN tag). If any DCB map is
applied and/or DCB is enabled this is causing the hardware to insert a
VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet.
Fix this by preventing VLAN tag 0 from being added when any VLAN is
already present after dmac/smac (software offloaded) or skb (hardware
offloaded).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter
for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional
unicast/multicast filters.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently a user is not allowed to clear a VF's administratively set MAC
on the PF. Fix this by allowing an all zero MAC address via "ip link set
${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00".
An example use case for this would be issuing a "virsh shutdown"
command on a VM. The call to iproute mentioned above is part of this flow.
Without this change the driver incorrectly rejects clearing the VF's
administratively set MAC and prints unhelpful log messages.
Also, improve the comments surrounding this change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
