Firmware error recover is the major change in this spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each tls context maintains two cipher contexts (one each for tx and rx
directions). For each tls session, the constants such as protocol
version, ciphersuite, iv size, associated data size etc are same for
both the directions and need to be stored only once per tls context.
Hence these are moved from 'struct cipher_context' to 'struct
tls_prot_info' and stored only once in 'struct tls_context'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need separate lines for calculating register values.
Also add comment that value is different than in vendor driver.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The TX_PIN_CFG_RFRX_EN bit was not set on other devices than MT7620,
restore old behavaviour since setting this bit maight not be
correct for older devices.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not enable TX_PIN_CFG_LNA_PE_A* bits for 2.4GHz band and
vice versa TX_PIN_CFG_LNA_PE_G* bits for 5GHz.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register 66 was causing issues on RT6352 if set to the same value as
in MTK driver. With 1c reg value device was working fine in both HT20
and HT40 modes.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove band check from rf53xx channel config routine since all chips
using it are single band.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The parameter order for clamp is supposed to be clamp(value, low, high).
When we write it in this order it's equivalent to
min(head->plcp[3] & 0x7f, 75) which works in this context where the min
is zero. But it's not a correct use of the API.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c: In function 'rtl8180_probe':
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1727:15: warning:
variable 'io_addr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1726:16: warning:
variable 'mem_addr' set but not used [-Wunused-but-set-variable]
They're never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace hard coded function name with __func__, to
improve robustness and to conform to the Linux kernel coding
style. Issue found using checkpatch.
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As it is, doing something like
# iw phy phy0 interface add foobar type ibss
on a firmware that doesn't have ad-hoc support just yields failures of
HostCmd_CMD_SET_BSS_MODE, which happened to return a '-1' error code
(-EPERM? not really right...) and sometimes may even crash the firmware
along the way.
Let's parse the firmware capability flag while registering the wiphy, so
we don't allow attempting IBSS at all, and we get a proper -EOPNOTSUPP
from nl80211 instead.
Fixes: e267e71e68 ("mwifiex: Disable adhoc feature based on firmware capability")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NL80211_TX_POWER_LIMITED was treated as NL80211_TX_POWER_AUTOMATIC,
which is the opposite of what should happen and can cause nasty
regulatory problems.
if/else converted to a switch without default to make gcc warn
on unhandled enum values.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/marvell/libertas_tf/main.c: In function 'lbtf_rx':
drivers/net/wireless/marvell/libertas_tf/main.c:554:15: warning:
variable 'flags' set but not used [-Wunused-but-set-variable]
It never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of exposing the signal-to-noise ration, calculate the actual signal
level taking the noise floor into account.
Also, flip the SIGNAL_DBM bit on, so that mac80211 exposes the signal
level along with the station info in scan results. This fills
NetworkManager's "nmcli d wifi output" output with colors, bars and joy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Also, turn it to a dev_info() to make checkpatch.pl happy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It doesn't make sense and the USB core warns on each submit of such
URB, easily flooding the message buffer with tracebacks.
Analogous issue was fixed in regular libertas driver in commit 6528d88047
("libertas: don't set URB_ZERO_PACKET on IN USB transfer").
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Logging each and every command response is way too much for INFO level.
Silence this, unless CONFIG_LIBERTAS_THINFIRM_DEBUG has been enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_main.c: In function 'rsi_prepare_skb':
drivers/net/wireless/rsi/rsi_91x_main.c:127:24: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rsi/rsi_91x_main.c:124:28: warning:
variable 'info' set but not used [-Wunused-but-set-variable]
They're not used any more since 160ee2a11c ("rsi: fill rx_params only once.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fixes to spelling mistakes in various files in rsi folder.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a \b (backspace) character in the message that wasn't intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function 'brcmf_usb_state_change':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:578:6: warning:
variable 'old_state' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro will be used in more places not just the cfg80211.c. It makes
sense to pass some common struct to it as "struct wiphy" is mostly
referenced in cfg80211 code only.
A very common one (used above the bus abstraction layer) is struct
brcmf_pub. Many functions already keep reference to it which will make
using bphy_err() simpler. It should also allow extending that macro's
logic if it's ever needed.
This improves code recently added in the commit 3ef005b82e ("brcmfmac:
add bphy_err() and use it in the cfg80211.c").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far 160 MHz channels were treated as 20 MHz ones which was breaking
support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and
its assumptions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware is capable of reporting ring status. It's used e.g. to signal
some problem with a specific ring setup. This patch adds support for
printing ring & error number which may be useful for debugging setup
issues.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The local variable chipname is string representation of chip id and revision
which is printed in the good flow of brcmf_fw_alloc_request(). Also use it
for the error path, ie. for unknown/unsupported devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware crashes during the probe sequence we provide little
information on what really failed. This patch checks the sdpcm shared
location and show the trap information if a firmware trap has happened.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The MBSS feature was already disabled for bcm43362 as it resulted in a
beacon with BRCM_TEST_SSID regardless user configuration in hostapd. Now
the same has been reported for bcm4330 so disable the feature for this
device as well.
Reported-by: Russell King <linux@armlinux.org.uk>
Tested-by: Christopher Martin <chrsmrtn@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we moved the drivers debugfs directory under ieee80211 debugfs the
debugfs entries need to be added after wiphy_register() has been called.
For most part that has been done accordingly, but for the debugfs entries
added by SDIO it was not and failed silently. This patch fixes that by
adding a bus-layer callback for it.
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Reported-by: Russel King <linux@armlinux.org.uk>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For USB there is no separate channel being used to pass events
from firmware to the host driver and as such are passed over the
data path. In order to detect mock event messages an additional
check is needed on event subtype. This check is added conditionally
using unlikely() keyword.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SSID length as received from firmware should not exceed
IEEE80211_MAX_SSID_LEN as that would result in heap overflow.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
WARNING: line over 80 characters
#316: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.c:1751:
+ SET_8821AE_H2CCMD_AOAC_RSVDPAGE_LOC_GTK_EXT_MEM(u1rsvdpageloc2, GTKEXT_PG);
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
^
WARNING: Comparisons should place the constant on the right side of the test
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
CHECK: spaces preferred around that '&' (ctx:VxV)
#501: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2666:
+ pwrinfo24g->bw40_diff[rfpath][txcount] = (hwinfo[eeaddr]&0xf0) >> 4;
^
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#211: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:109:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#241: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:277:
+ ptmp_byte = (u8 *) (®toset) + index;
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch affects modules rtl8192ce, rtl8192cu, and rtl8192com.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#237: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:90:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#744: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:329:
+ pwr_val[i] = (u8) ((writeval & (0x7f <<
CHECK: No space is necessary after a cast
#784: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:365:
+ (u8) writeval);
CHECK: spaces preferred around that '/' (ctx:VxV)
#963: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:513:
+ txqpageunit = txqpagenum/outepnum;
^
CHECK: Unnecessary parentheses around 'outepnum > 1'
#975: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:521:
+ if ((outepnum > 1) && (txqremaininpage))
CHECK: Alignment should match open parenthesis
#1059: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:617:
+static void _rtl92cu_init_chipn_two_out_ep_priority(struct ieee80211_hw *hw,
bool wmm_enable,
ERROR: "foo * bar" should be "foo *bar"
#1940: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:591:
+void rtl92cu_fill_fake_txdesc(struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver contains one instance of a CamelCase variable, namely
IS_81xxC_VENDOR_UMC_A_CUT. This macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
File halbt_precomp.h contains the only CamelCase value, namely
GetDefaultAdapter, but that macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are a number of CamelCase variables remaining in the source
files of modules rtl_pci, rtl_usb, and rtlwifi.
The following checkpatch excettions are also fixed:
for_kalle1/0001-rtlwifi-Remove-CamelCase-variables-from-base-code.patch
-----------------------------------------------------------------------
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
WARNING: line over 80 characters
#70: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:379:
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
CHECK: No space is necessary after a cast
#186: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:396:
+ status->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#208: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c:335:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#243: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:301:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#252: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:368:
+ stats.rx_is40mhzpacket = (bool) GET_RX_DESC_BW(rxdesc);
CHECK: No space is necessary after a cast
#265: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c:475:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
WARNING: Unnecessary space before function pointer arguments
#455: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:1462:
+ void (*writen_sync) (struct rtl_priv *rtlpriv, u32 addr, void *buf,
WARNING: Unnecessary space before function pointer arguments
#483: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:2257:
+ void (*fill_fake_txdesc) (struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
