[ Upstream commit 1f1496a923b6ba16679074fe77100e1b53cdb880 ]
Setup the port uartclk in sifive_serial_probe() so that the base baud
rate is correctly printed during device probe instead of always showing
"0". I.e. the probe message is changed from
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 0) is a SiFive UART v0
to the correct:
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 115200) is a SiFive UART v0
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e4e636e0e3e0b5deffc5e233adcb2cd4e68f2d0 ]
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201119141126.168850-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f70e49ed860020f5abae4f7015018ebc10e1f0e upstream.
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d26 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com>
Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 699cc4dfd1 (tty: serial: imx: add imx earlycon driver), the earlycon
part of imx serial is a separate driver and isn't necessarily enabled anymore
when the console is enabled. This causes users to loose the earlycon
functionality when upgrading their kenrel configuration via oldconfig.
Enable earlycon by default when IMX_SERIAL_CONSOLE is enabled.
Fixes: 699cc4dfd1 (tty: serial: imx: add imx earlycon driver)
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20201105204026.1818219-1-l.stach@pengutronix.de
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to the commit that this one fixes, the FIFO size was derived from
the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following
formula:
TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1)
The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A
LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ
being equal to 4, and in the register description for LPUARTx_FIFO, it
shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011",
even though these registers read as "101" in reality.
And when LPUART on LS1021A was working, the "101" value did correspond
to "16 datawords", by applying the formula above, even though the
documentation is wrong again (!!!!) and says that "101" means 64 datawords
(hint: it doesn't).
So the "new" formula created by commit f77ebb241c has all the premises
of being wrong for LS1021A, because it relied only on false data and no
actual experimentation.
Interestingly, in commit c2f448cff2 ("tty: serial: fsl_lpuart: add
LS1028A support"), Michael Walle applied a workaround to this by manually
setting the FIFO widths for LS1028A. It looks like the same values are
used by LS1021A as well, in fact.
When the driver thinks that it has a deeper FIFO than it really has,
getty (user space) output gets truncated.
Many thanks to Michael for pointing out where to look.
Fixes: f77ebb241c ("tty: serial: fsl_lpuart: correct the FIFO depth size")
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com
Reviewed-by：Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 293f899594 ("tty: serial: 21285: stop using the unused[]
variable from struct uart_port") introduced a bug which stops the
transmit interrupt being disabled when there are no characters to
transmit - disabling the transmit interrupt at the interrupt controller
is the only way to stop an interrupt storm. If this interrupt is not
disabled when there are no transmit characters, we end up with an
interrupt storm which prevents the machine making forward progress.
Fixes: 293f899594 ("tty: serial: 21285: stop using the unused[] variable from struct uart_port")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/E1kU4GS-0006lE-OO@rmk-PC.armlinux.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl+TT4gPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx322MP/1mI56SyOFx30AqtWBPSjHJp+DzhOObyb4vD
ndYuicBIn9tJwvVRBBZkfsbIU8EENVwrN3hOpesaj9L7xiqOqKakcnyC1REYmpIs
8XBDfdZzy5PrMHIu3fF1ZDCQyO7KndGf5DfLVxJtcf1tSPQyQCuIA3FtS6d8Bxnz
r491+om67ucnlFD5X0Spm3RdZH+ECmXx2iXwoS0Zi7P+X+S+ovG8wBV/X0ggeoBc
Zgi4W01SiRupmSVZ6PA7FvWaLGQErQAALQOcFtMcFgjeWzc1v2QzcURELH8JW7ro
72AH9st1Kvi3hoN2HNNzUnNUdQvZ+AdH8skMIpN/e1cBYqYStAF3gm/R9h+iVHbG
GMmgzXHAFErfAW2UcF8tq1CzvQ5ChcTLNXdeoa8CeQbcDfocF3EyuKSPuDH+ve0H
kk4tPesTAc6XCEVwLaGnoC75sdum5mSi8h9vqhln2KCdeTY7jxzH9YGHjm71Supb
kV9vqo5Q5U/c5l2nU4r5q/DZdIahKsk3HIQZ0iG7BifAzamaTh4uyLVjtM6HSwNz
tdHZaxoHd/PLI5IoeggFelx6qgvK5qVRLP0evgOdTLRFLj/ZbrOf0Q7DjdTy2BjZ
Lgq461QqNapOzxq43G2IDT2+P62Q1+d+YLCKBgaGQaJicyU5m9STCNo3UBb1qH1h
W6UwGF5z
=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make usage
of usage of 16byte load/stores possible
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=Aa/Q
-----END PGP SIGNATURE-----
Merge tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make use
of 16byte load/stores possible
- cleanups and fixes
* tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (92 commits)
MIPS: DEC: Restore bootmem reservation for firmware working memory area
MIPS: dec: fix section mismatch
bcm963xx_tag.h: fix duplicated word
mips: ralink: enable zboot support
MIPS: ingenic: Remove CPU_SUPPORTS_HUGEPAGES
MIPS: cpu-probe: remove MIPS_CPU_BP_GHIST option bit
MIPS: cpu-probe: introduce exclusive R3k CPU probe
MIPS: cpu-probe: move fpu probing/handling into its own file
MIPS: replace add_memory_region with memblock
MIPS: Loongson64: Clean up numa.c
MIPS: Loongson64: Select SMP in Kconfig to avoid build error
mips: octeon: Add Ubiquiti E200 and E220 boards
MIPS: SGI-IP28: disable use of ll/sc in kernel
MIPS: tx49xx: move tx4939_add_memory_regions into only user
MIPS: pgtable: Remove used PAGE_USERIO define
MIPS: alchemy: Share prom_init implementation
MIPS: alchemy: Fix build breakage, if TOUCHSCREEN_WM97XX is disabled
MIPS: process: include exec.h header in process.c
MIPS: process: Add prototype for function arch_dup_task_struct
MIPS: idle: Add prototype for function check_wait
...
After some unsuccessful attempts to use sysrq over console, figured
out that port->has_sysrq should likely be enabled, as per other
architectures, this when CONFIG_SERIAL_MCF_CONSOLE is also enabled.
Tested some magic sysrq commands (h, p, t, b), they works now
properly. Commands works inside 5 secs after BREAK is sent, as
expected.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20201002140545.477481-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add handling of magic sysrq keys when using dma/edma.
Tested by sending BREAK followed by a sysrq command inside
a 5 secs time window, by:
echo 1 > /proc/sys/kernel/sysrq
BREAK + h, t, e, b, c
Tested also sending a command after 5 secs after BREAK, that's
properly ignored.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20201004161144.1307174-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the RX interrupt logic uses the RXEMPTY interrupt, with the
RXEMPTYINV bit set, which means we get an RX interrupt as soon as the
RX FIFO is non-empty.
However, with the MAX310X having a FIFO of 128 bytes, this makes very
poor use of the FIFO: we trigger an interrupt as soon as the RX FIFO
has one byte, which means a lot of interrupts, each only collecting a
few bytes from the FIFO, causing a significant CPU load.
Instead this commit relies on two other RX interrupt events:
- MAX310X_IRQ_RXFIFO_BIT, which triggers when the RX FIFO has reached
a certain threshold, which we define to be half of the FIFO
size. This ensure we get an interrupt before the RX FIFO fills up.
- MAX310X_LSR_RXTO_BIT, which triggers when the RX FIFO has received
some bytes, and then no more bytes are received for a certain
time. Arbitrarily, this time is defined to the time is takes to
receive 4 characters.
On a Microchip SAMA5D3 platform that is receiving 20 bytes every 16ms
over one MAX310X UART, this patch has allowed to reduce the CPU
consumption of the interrupt handler thread from ~25% to 6-7%.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lore.kernel.org/r/20201001074415.349739-1-thomas.petazzoni@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been discovered that there is a potential deadlock between
the clock-change-notifier thread and the UART port suspending one:
CPU0 (suspend CPU/UART) CPU1 (update clock)
---- ----
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
*** DEADLOCK ***
The best way to fix this is to eliminate the CPU0
port->mutex/work-completion scenario. So we suggest to register and
unregister the clock-notifier during the DW APB UART port probe/remove
procedures, instead of doing that at the points of the port
startup/shutdown.
Link: https://lore.kernel.org/linux-serial/f1cd5c75-9cda-6896-a4e2-42c5bfc3f5c3@redhat.com
Fixes: cc816969d7 ("serial: 8250_dw: Fix common clocks usage race condition")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is erroneous to update the TTY port baud rate if it hasn't been
initialized yet, because in that case the TTY struct isn't set. So there
is no termios structure to get and re-calculate the baud if the current
baud can't be reached. Let's skip the baud rate update then until the port
is fully initialized.
Note the update UART clock method still sets the uartclk member with a new
ref clock value even if the port is turned off. The new UART ref clock
rate will be used later on the port starting up procedure.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been a mistake to add the MCR register RTS/DTS fields setting in
the generic method of the UART reference clock update. There is no point
in asserting these lines at that procedure. Just discard the
serial8250_out_MCR() mathod invocation from there then.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPG clock is disabled at the end of imx_uart_shutdown(); we really
don't want to run any IRQ handlers after this point.
At least on i.MX8MN, the UART will happily continue to generate interrupts
even with its clocks disabled, but in this state, all register writes are
ignored (which will cause the shadow registers to differ from the actual
register values, resulting in all kinds of weirdness).
In a transfer without DMA, this could lead to the following sequence of
events:
- The UART finishes its transmission while imx_uart_shutdown() is run,
triggering the TXDC interrupt (we can trigger this fairly reliably by
writing a single byte to the TTY and closing it right away)
- imx_uart_shutdown() finishes, disabling the UART clocks
- imx_uart_int() -> imx_uart_transmit_buffer() -> imx_uart_stop_tx()
imx_uart_stop_tx() should now clear UCR4_TCEN to disable the TXDC
interrupt, but this register write is ineffective. This results in an
interrupt storm.
To disable all interrupts in the same place, and to avoid setting UCR4
twice, clearing UCR4_OREN is moved below del_timer_sync() as well; this
should be harmless.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200925082412.12960-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the port of the commit db1b5bc047 ("serial: 8250: Fix TX
interrupt handling condition") to the 8250_fsl irq handling logic.
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Andrij Abyzov <aabyzov@slb.com>
Link: https://lore.kernel.org/r/20200928144127.87156-1-aabyzov@slb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issuing a magic-sysrq via the PL011 causes the following lockdep splat,
which is easily reproducible under QEMU:
| sysrq: Changing Loglevel
| sysrq: Loglevel set to 9
|
| ======================================================
| WARNING: possible circular locking dependency detected
| 5.9.0-rc7 #1 Not tainted
| ------------------------------------------------------
| systemd-journal/138 is trying to acquire lock:
| ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70
|
| but task is already holding lock:
| ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488
|
| which lock already depends on the new lock.
[...]
| Possible unsafe locking scenario:
|
| CPU0 CPU1
| ---- ----
| lock(&port_lock_key);
| lock(console_owner);
| lock(&port_lock_key);
| lock(console_owner);
|
| *** DEADLOCK ***
The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.
Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.
Cc: <stable@vger.kernel.org> # 4.19+
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2nd and 3rd parameter were wrongly used, and cause kernel abort when
doing kgdb debug.
Fixes: 1da17d7cf8 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For QUP IP versions 2.5 and above the oversampling rate is
halved from 32 to 16.
Commit ce73460054 ("tty: serial: qcom_geni_serial: Update
the oversampling rate") is pushed to handle this scenario.
But the existing logic is failing to classify QUP Version 3.0
into the correct group ( 2.5 and above).
As result Serial Engine clocks are not configured properly for
baud rate and garbage data is sampled to FIFOs from the line.
So, fix the logic to detect QUP with versions 2.5 and above.
Fixes: ce73460054 ("tty: serial: qcom_geni_serial: Update the oversampling rate")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Paras Sharma <parashar@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a warning shows that 'ret' becomes an unused variable
after simplify the return expression of mvebu_uart_probe(). So
remove it.
Fixes: b63537020d ("serial: mvebu-uart: simplify the return expression of mvebu_uart_probe()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20200929085651.158283-1-miaoqinglang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aarch64-linux-gnu-ld: drivers/tty/serial/imx_earlycon.o: in function `imx_uart_console_early_write':
imx_earlycon.c:(.text+0x84): undefined reference to `uart_console_write'
The driver uses the uart_console_write(), but SERIAL_CORE_CONSOLE is not
selected, so uart_console_write is not defined, then we get the error.
Fix this by selecting SERIAL_CORE_CONSOLE.
Fixes: 699cc4dfd1 ("tty: serial: imx: add imx earlycon driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20200919063240.2754965-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1600601186-7420-2-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here and this resolves a merge issue in
the 8250 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a part of system suspend uart_port_suspend is called from the
Serial driver, which calls set_mctrl passing mctrl as 0. This
makes RFR high(NOT_READY) during suspend.
Due to this BT SoC is not able to send wakeup bytes to UART during
suspend. Include if check for non-suspend case to keep RFR low
during suspend.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1599742438-16811-5-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the port-lock initialisation regression introduced by commit
a3cb39d258 ("serial: core: Allow detach and attach serial device for
console") by making sure that the lock is again initialised during
console setup.
The console may be registered before the serial controller has been
probed in which case the port lock needs to be initialised during
console setup by a call to uart_set_options(). The console-detach
changes introduced a regression in several drivers by effectively
removing that initialisation by not initialising the lock when the port
is used as a console (which is always the case during console setup).
Add back the early lock initialisation and instead use a new
console-reinit flag to handle the case where a console is being
re-attached through sysfs.
The question whether the console-detach interface should have been added
in the first place is left for another discussion.
Note that the console-enabled check in uart_set_options() is not
redundant because of kgdboc, which can end up reinitialising an already
enabled console (see commit 42b6a1baa3 ("serial_core: Don't
re-initialize a previously initialized spinlock.")).
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f743061a85 ("serial: core: Initialise spin lock before use in
uart_configure_port()") tried to work around a breakage introduced by
commit a3cb39d258 ("serial: core: Allow detach and attach serial
device for console") by adding a second initialisation of the port lock
when registering the port.
As reported by the build robots [1], this doesn't really solve the
regression introduced by the console-detach changes and also adds a
second redundant initialisation of the lock for normal ports.
Start cleaning up this mess by removing the redundant initialisation and
making sure that the port lock is again initialised once-only for ports
that aren't already in use as a console.
[1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian
Fixes: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c5cbc78acf ("tty: serial: qcom_geni_serial: Initialize baud
in qcom_geni_console_setup") fixed a bug by initting a variable that
was used in some cases without initialization. However, the "default"
baud rate picked by that CL was probably not the best choice. The
chances that anyone out there is trying to run a system with kernel
messages piped out over a 9600 baud serial port is just about nil.
Console messages are printed in a blocking manner. At 9600 baud we
print about 1 character per millisecond which means that printing a
40-byte message to the console will take ~40 ms. While it would
probably work, it's going to make boot _very_ slow and probably cause
the occasional timeout here and there in drivers (heck, even at 115200
console delays can wreck havoc).
This has already bit at least two people that I'm aware of that tried
to enable serial console by just adding "console=ttyMSM0" (instead of
"console=ttyMSM0,115200n8") to the command line, so it seems like it'd
be nice to fix.
Let's switch the default to 115200.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200911080054.1.I4c00b921c2f17b6988688046fa7be0f729f8d591@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use mmio32, we also need to set regshift.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Link: https://lore.kernel.org/r/20200915054825.3289105-2-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 devices may modify iotype in their own earlycon setup. For example:
8250_mtk and 8250_uniphier force iotype to be MMIO32. Print earlycon info
after match->setup to reflect actual earlycon info.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200915054825.3289105-1-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This eliminates the following sparse warning:
drivers/tty/serial/ucc_uart.c:286:6: warning: symbol 'qe_uart_set_mctrl'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200912033834.143166-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
SB1250 uart bug is related to PASS 2 workarounds. Use config
CONFIG_SB1_PASS_2_WORKAROUNDS directly and get rid of SIBYTE_1956_WAR.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This adds support for ACPI enumerated FSL 16550 UARTs.
For supporting ACPI, I added a wrapper so that this driver
can be used if firmware has exposed the HID "NXP0018" in
DSDT table.
This will be built as object file if config "SERIAL_8250_FSL"
is enabled which depends on config "SERIAL_8250_CONSOLE".
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Link: https://lore.kernel.org/r/20200903113402.12371-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Fixes: 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200831171045.205691-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac588759 ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some derivates of sc16is7xx devices expose more than one tty device to
userspace. If multiple such devices exist in a system, userspace
currently has no clean way to infer which tty maps to which physical
line.
Set the .iobase value to the relative index within the device to allow
infering the order through sysfs.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200901120329.4176302-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
