q->now is increased during dequeue and doesn't contain the current time
afterwards, resulting in a too large timeout value for the qdisc watchdog.
Use "now" instead, which still contains the current time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer resolution exported in /proc/net/psched is used by userspace to
calculate HTB's burst values. Currently it is set to HZ, since we're now
using hrtimers, use KTIME_MONOTONIC_RES, which makes HTB use smaller burst
values.
This patch also affects libnl, which incorrectly uses this value for
the SFQ perturbation parameter, which is always in seconds, and some
routing cache values, which are in USER_HZ, so both cases are broken
anyway.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all packet schedulers have been converted to hrtimers most users
of PSCHED_JIFFIE2US and PSCHED_US2JIFFIE are gone. The remaining users use
it to convert external time units to packet scheduler clock ticks, so use
PSCHED_TICKS_PER_SEC instead.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch delay_timer to hrtimer.
The class penalty parameter is changed to use psched ticks as units.
Since iproute never supported using this and the only existing user
(libnl) incorrectly assumes psched ticks as units anyway, this
shouldn't break anything.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
cbq_undelay_prio is supposed to return a time delta, but returns the
current time for non-active priorities, causing cbq_undelay to mark
the priority as active and schedule a timer for twice the current
time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the manual clock source selection mess and use ktime. Also
use a scalar representation, which allows to clean up pkt_sched.h a bit
more and results in less ktime_to_ns() calls in most cases.
The PSCHED_US2JIFFIE/PSCHED_JIFFIE2US macros are implemented quite
inefficient by this patch, following patches will convert all qdiscs
to hrtimers and get rid of them entirely.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time we have to set it to skb->tail that is not anymore equal to
skb->data, so we either add a new helper or just add the skb->tail - skb->data
offset, for now do the later.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_nd_hdr is always called immediately after a alloc_skb + skb_reserve
sequence, i.e. when skb->tail is equal to skb->data, making it correct to use
skb_reset_network_header().
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to the skb_reset_network_header(), i.e. at the point we reset
the transport header pointer/offset skb->tail is equal to skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nfattr_parse to parse attributes, this patch also modifies the default
behaviour since unknown attributes will be ignored instead of returning
EINVAL. This ensure backward compatibility: new libraries with new
attributes and old kernels can work.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch let userspace programs set the IP_CT_TCP_BE_LIBERAL flag to
force the pickup of established connections.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PUSH flag is accepted with every other valid combination.
Let's get it out of the tcp_valid_flags table and reduce the
number of combinations we have to handle. This does not
significantly reduce the table size however (8 bytes).
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This combination has been encountered on an IBM AS/400 in response
to packets sent to a closed session. There is no particular reason
to mark it invalid.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the codes to copy netfilter related datas. Before copying,
nf_copy() puts original members in destination skb.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the codes to copy netfilter related datas. Note that
__nf_copy() assumes destination skb doesn't have any netfilter
related members.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it uses jhash, but using jhash2 would be around 3-4 times faster
(on P4).
Signed-off-by: Sami Farin <safari-netfilter@safari.iki.fi>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
subsys_table is initialized to NULL, therefore just returns NULL in case
that it is not set.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove nfnetlink_check_attributes duplicates message size and callback
id checks. nfnetlink_find_client and nfnetlink_rcv_msg already do
such checks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The retrying after an allocation failure is not necessary anymore
since we're holding the mutex the entire time, for the same
reason the double allocation race can't happen anymore.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we don't use nf_conntrack_lock anymore but a single mutex for
all protocol handling, no need to release and grab it again for sysctl
registration.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ugly special-casing of nf_conntrack_l4proto_generic, all it
wants is its sysctl tables registered, so do that explicitly in an
init function and move the remaining protocol initialization and
cleanup code to nf_conntrack_proto.c as well.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol lookups done by nf_conntrack are already protected by RCU,
there is no need to keep taking nf_conntrack_lock for registration
and unregistration. Switch to a mutex.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the obsolete IPv4 only connection tracking/NAT as scheduled in
feature-removal-schedule.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove xt_proto_prefix array which duplicates xt_prefix and change all
users of xt_proto_prefix to xt_prefix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are a bit more subtle, they are of this type:
- skb->h.raw = payload;
__skb_pull(skb, payload - skb->data);
+ skb_reset_transport_header(skb);
__skb_pull results in:
skb->data = skb->data + payload - skb->data;
skb->data = payload;
So after __skb_pull we have skb->data pointing to payload and we can
just call skb_reset_transport_header(skb), that will do:
skb->h.raw = payload;
The others are similar, allowing us to get rid of some more cases where a
pointer was being attributed to the layer headers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.
Ditched a no-op in bnx2 in the process.
I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->h.raw accessors.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->h.raw accessors.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where the transport header is being set to a offset from
skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->h.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use logic operations rather than memcmp() to compare destination
address with link local multicast addresses.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...
Just out of curiosity, here are the idioms found to get the same result:
skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't access skb->nh.raw directly anymore, it will become an offset.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Show what protocols are bound to what packet types in /proc/net/ptype
Uses kallsyms to decode function pointers if possible.
Example:
Type Device Function
ALL eth1 packet_rcv_spkt+0x0
0800 ip_rcv+0x0
0806 arp_rcv+0x0
86dd :ipv6:ipv6_rcv+0x0
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The seq_file operations stuff can be marked constant to
get it out of dirty cache.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Eric, mark packet type and network device watermarks
as read mostly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where the network header is being set to a offset from skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the network header, it is still legal
to touch skb->nh.raw directly if just adding to, subtracting from or setting it
to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->nh.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting it to skb->h.raw, which is valid, in the (to become) old pointer based
world order and in the new world of offset based layer headers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now related to this form:
skb->nh.ipv6h = (struct ipv6hdr *)skb_put(skb, length);
That, as the others, is done when skb->tail is still equal to skb->data, making
the conversion to skb_reset_network_header possible.
Also one more case equivalent to skb->nh.raw = skb->data, of this form:
iph = (struct ipv6hdr *)skb->data;
<SNIP>
skb->nh.ipv6h = iph;
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some more cases where skb->nh.iph was being set that were converted
to using skb_reset_network_header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
boot_pkt->iph is the first member, that is at skb->data, so just use
skb_reset_network_header().
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time of the type:
skb->nh.iph = (struct iphdr *)skb->data;
That is completely equivalent to:
skb->nh.raw = skb->data;
Wonder why people love casts... :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It returns skb->data, so we can just use skb_reset_network_header after it.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
But only in the cases where its a newly allocated skb, i.e. one where skb->tail
is equal to skb->data, or just after skb_reserve, where this requirement is
maintained.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_push updates and returns skb->data, so we can just call
skb_reset_network_header after the call to skb_push.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nh.ipv6h is there exactly for this reason! Use it while it exists ;-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That is equal to skb->head before skb_reserve, to help in the layer header
changes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where we want to set skb->mac.raw to an offset from skb->data.
Simple cases first, the memmove ones and specially pktgen will be left for later.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_push updates and returns skb->data, so we can just call
skb_reset_mac_header after the call to skb_push.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->head is equal to skb->data after alloc_skb, so reset the mac header while
this is true, i.e. before skb_reserve.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all the _type_trans routines are consistent in this regard.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that network timestamps use ktime_t infrastructure, we can add a new
SOL_SOCKET sockopt SO_TIMESTAMPNS.
This command is similar to SO_TIMESTAMP, but permits transmission of
a 'timespec struct' instead of a 'timeval struct' control message.
(nanosecond resolution instead of microsecond)
Control message is labelled SCM_TIMESTAMPNS instead of SCM_TIMESTAMP
A socket cannot mix SO_TIMESTAMP and SO_TIMESTAMPNS : the two modes are
mutually exclusive.
sock_recv_timestamp() became too big to be fully inlined so I added a
__sock_recv_timestamp() helper function.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: linux-arch@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
net_msg_warn should be placed in the read_mostly section, to avoid
performance problems on SMP
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug noticed by Chris Wright <chrisw@sous-sol.org>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We returned incorrect result with IPV6_RTHDRDSTOPTS, IPV6_RTHDR and
IPV6_DSTOPTS.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of functions are exported or used indirectly
so it is pointless to mark them as inline.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several functions are marked inline or forced inline, but it
would be better to let the compiler decide.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add whitespace around keywords.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add whitespace around keywords.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix whitespace around keywords. Fix indentation especially of switch
statements.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix whitespace around keywords. Eliminate unnecessary ()'s on return
statements.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix whitespace around keywords.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Covert network warning messages from a compile time to runtime choice.
Removes kernel config option and replaces it with new /proc/sys/net/core/warnings.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now network timestamps use ktime_t infrastructure, we can add a new
ioctl() SIOCGSTAMPNS command to get timestamps in 'struct timespec'.
User programs can thus access to nanosecond resolution.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the following not or no longer used exports:
- drivers/char/random.c: secure_tcp_sequence_number
- net/dccp/options.c: sysctl_dccp_feat_sequence_window
- net/netlink/af_netlink.c: netlink_set_err
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the write queue implementation to be changed,
for example, to one which allows fast interval searching.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch eliminates some duplicate code for the verification of
receive checksums between UDP-Lite and UDP. It does this by
introducing __skb_checksum_complete_head which is identical to
__skb_checksum_complete_head apart from the fact that it takes
a length parameter rather than computing the first skb->len bytes.
As a result UDP-Lite will be able to use hardware checksum offload
for packets which do not use partial coverage checksums. It also
means that UDP-Lite loopback no longer does unnecessary checksum
verification.
If any NICs start support UDP-Lite this would also start working
automatically.
This patch removes the assumption that msg_flags has MSG_TRUNC clear
upon entry in recvmsg.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the changeset
[IPV6]: UDPv6 checksum.
We always need to check UDPv6 checksum because it is mandatory.
The sk_filter optimisation has nothing to do whether we verify the
checksum. It simply postpones it to the point when the user calls
recv or poll.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Some sysctl vars are declared __read_mostly
2) We can avoid updating stack[] when doing an AVL lookup only.
lookup() macro is extended to receive a second parameter, that may be NULL
in case of a pure lookup (no need to save the AVL path). This removes
unnecessary instructions, because compiler knows if this _stack parameter is
NULL or not.
text size of net/ipv4/inetpeer.o is 2063 bytes instead of 2107 on x86_64
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate need for full 6/4/64 divide to compute queue.
Variable maxqueue was really a constant.
Fix indentation.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Newton-Raphson method is quadratically convergent so
only a small fixed number of steps are necessary.
Therefore it is faster to unroll the loop. Since div64_64 is no longer
inline it won't cause code explosion.
Also fixes a bug that can occur if x^2 was bigger than 32 bits.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet6_ifaddr for source address of RS is leaked if the address
is not an optimistic address.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nominally an autoconfigured IPv6 address is added to an interface in the
Tentative state (as per RFC 2462). Addresses in this state remain in this
state while the Duplicate Address Detection process operates on them to
determine their uniqueness on the network. During this period, these
tentative addresses may not be used for communication, increasing the time
before a node may be able to communicate on a network. Using Optimistic
Duplicate Address Detection, autoconfigured addresses may be used
immediately for communication on the network, as long as certain rules are
followed to avoid conflicts with other nodes during the Duplicate Address
Detection process.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_tunnel before supporting IPv4/IPv6 tunnel allows only IPPROTO_IPV6
in configurations from userland. This allows userland to set IPPROTO_IPIP
and 0(wildcard). ip6_tunnel only handles allowed inner protocols.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some notes
- Protocol number IPPROTO_IPIP is used for IPv4 over IPv6 packets.
- If IP6_TNL_F_USE_ORIG_TCLASS is set, TOS in IPv4 header is copied to
Traffic Class in outer IPv6 header on xmit.
- IP6_TNL_F_USE_ORIG_FLOWLABEL is ignored on xmit of IPv4 packets, because
IPv4 header does not have flow label.
- Kernel sends ICMP error if IPv4 packet is too big on xmit, even if
DF flag is not set.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables to add IPv4/IPv6 specific handling later,
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables to add IPv4/IPv6 specific handling later,
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables to add IPv4/IPv6 specific error handling later,
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user passes MSG_TRUNC in via msg_flags, return
the full packet size not the truncated size.
Idea from Herbert Xu and Thomas Graf.
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use a special structure (struct skb_timeval) and plain
'struct timeval' to store packet timestamps in sk_buffs and struct
sock.
This has some drawbacks :
- Fixed resolution of micro second.
- Waste of space on 64bit platforms where sizeof(struct timeval)=16
I suggest using ktime_t that is a nice abstraction of high resolution
time services, currently capable of nanosecond resolution.
As sizeof(ktime_t) is 8 bytes, using ktime_t in 'struct sock' permits
a 8 byte shrink of this structure on 64bit architectures. Some other
structures also benefit from this size reduction (struct ipq in
ipv4/ip_fragment.c, struct frag_queue in ipv6/reassembly.c, ...)
Once this ktime infrastructure adopted, we can more easily provide
nanosecond resolution on top of it. (ioctl SIOCGSTAMPNS and/or
SO_TIMESTAMPNS/SCM_TIMESTAMPNS)
Note : this patch includes a bug correction in
compat_sock_get_timestamp() where a "err = 0;" was missing (so this
syscall returned -ENOENT instead of 0)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
CC: John find <linux.kernel@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the current version of the 64 bit divide common code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where appropriate, convert references to xtime.tv_sec to the
get_seconds() helper function.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since devices can change name and other wierdness, don't hold onto
a copy of device name, instead use pointer to output device.
Fix a couple of leaks in error handling path as well.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing htonl() macro is smart enough to do the same code as
using __constant_htonl() and it looks cleaner.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can use random32() now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove private debug macro and replace with standard version
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_backlog is a critical field of struct sock. (known famous words)
It is (ab)used in hot paths, in particular in release_sock(), tcp_recvmsg(),
tcp_v4_rcv(), sk_receive_skb().
It really makes sense to place it next to sk_lock, because sk_backlog is only
used after sk_lock locked (and thus memory cache line in L1 cache). This
should reduce cache misses and sk_lock acquisition time.
(In theory, we could only move the head pointer near sk_lock, and leaving tail
far away, because 'tail' is normally not so hot, but keep it simple :) )
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Undoing ssthresh is disabled in fastretrans_alert whenever
FLAG_ECE is set by clearing prior_ssthresh. The clearing does
not protect FRTO because FRTO operates before fastretrans_alert.
Moving the clearing of prior_ssthresh earlier seems to be a
suboptimal solution to the FRTO case because then FLAG_ECE will
cause a second ssthresh reduction in try_to_open (the first
occurred when FRTO was entered). So instead, FRTO falls back
immediately to the rate halving response, which switches TCP to
CA_CWR state preventing the latter reduction of ssthresh.
If the first ECE arrived before the ACK after which FRTO is able
to decide RTO as spurious, prior_ssthresh is already cleared.
Thus no undoing for ssthresh occurs. Besides, FLAG_ECE should be
set also in the following ACKs resulting in rate halving response
that sees TCP is already in CA_CWR, which again prevents an extra
ssthresh reduction on that round-trip.
If the first ECE arrived before RTO, ssthresh has already been
adapted and prior_ssthresh remains cleared on entry because TCP
is in CA_CWR (the same applies also to a case where FRTO is
entered more than once and ECE comes in the middle).
High_seq must not be touched after tcp_enter_cwr because CWR
round-trip calculation depends on it.
I believe that after this patch, FRTO should be ECN-safe and
even able to take advantage of synergy benefits.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
A local variable for icsk was created but this change was
missing. Spotted by Jarek Poplawski.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
New sysctl tcp_frto_response is added to select amongst these
responses:
- Rate halving based; reuses CA_CWR state (default)
- Very conservative; used to be the only one available (=1)
- Undo cwr; undoes ssthresh and cwnd reductions (=2)
The response with rate halving requires a new parameter to
tcp_enter_cwr because FRTO has already reduced ssthresh and
doing a second reduction there has to be prevented. In addition,
to keep things nice on 80 cols screen, a local variable was
added.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reordering detection must work also when FRTO has not been
used at all which was the original intention of mine, just the
expression of the idea was flawed.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed in oprofile study a cache miss in tcp_rcv_established() to read
copied_seq.
ffffffff80400a80 <tcp_rcv_established>: /* tcp_rcv_established total: 4034293
2.0400 */
55493 0.0281 :ffffffff80400bc9: mov 0x4c8(%r12),%eax copied_seq
543103 0.2746 :ffffffff80400bd1: cmp 0x3e0(%r12),%eax rcv_nxt
if (tp->copied_seq == tp->rcv_nxt &&
len - tcp_header_len <= tp->ucopy.len) {
In this function, the cache line 0x4c0 -> 0x500 is used only for this
reading 'copied_seq' field.
rcv_wup and copied_seq should be next to rcv_nxt field, to lower number of
active cache lines in hot paths. (tcp_rcv_established(), tcp_poll(), ...)
As you suggested, I changed tcp_create_openreq_child() so that these fields
are changed together, to avoid adding a new store buffer stall.
Patch is 64bit friendly (no new hole because of alignment constraints)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, TCP code uses "sk" for struct sock pointer.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
YeAH-TCP is a sender-side high-speed enabled TCP congestion control
algorithm, which uses a mixed loss/delay approach to compute the
congestion window. It's design goals target high efficiency, internal,
RTT and Reno fairness, resilience to link loss while keeping network
elements load as low as possible.
For further details look here:
http://wil.cs.caltech.edu/pfldnet2007/paper/YeAH_TCP.pdf
Signed-off-by: Angelo P. Castellani <angelo.castellani@gmail.con>
Signed-off-by: David S. Miller <davem@davemloft.net>
